xen/swiotlb: Add support for 64KB page granularity
Swiotlb is used on ARM64 to support DMA on platform where devices are
not protected by an SMMU. Furthermore it's only enabled for DOM0.
While Xen is always using 4KB page granularity in the stage-2 page table,
Linux ARM64 may either use 4KB or 64KB. This means that a Linux page
can be spanned accross multiple Xen page.
The Swiotlb code has to validate that the buffer used for DMA is
physically contiguous in the memory. As a Linux page can't be shared
between local memory and foreign page by design (the balloon code always
removing entirely a Linux page), the changes in the code are very
minimal because we only need to check the first Xen PFN.
Note that it may be possible to optimize the function
check_page_physically_contiguous to avoid looping over every Xen PFN
for local memory. Although I will let this optimization for a follow-up.
Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
--- Cc: Russell King <linux@arm.linux.org.uk> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com>
Changes in v5:
- Patch was previously sent separately
- Add Stefano's reviewed-by
xen/swiotlb: Pass addresses rather than frame numbers to xen_arch_need_swiotlb
With 64KB page granularity support, the frame number will be different.
It will be easier to modify the behavior in a single place rather than
in each caller.
Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
--- Cc: Russell King <linux@arm.linux.org.uk> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: x86@kernel.org
Changes in v5:
- Patch was previously sent separately
- Fix compilation on x86 (spurious ; at the end of the
declaration)
- Add Stefano's reviewed-by
Julien Grall [Tue, 5 May 2015 15:36:56 +0000 (16:36 +0100)]
arm/xen: Add support for 64KB page granularity
The hypercall interface is always using 4KB page granularity. This is
requiring to use xen page definition macro when we deal with hypercall.
Note that pfn_to_gfn is working with a Xen pfn (i.e 4KB). We may want to
rename pfn_gfn to make this explicit.
We also allocate a 64KB page for the shared page even though only the
first 4KB is used. I don't think this is really important for now as it
helps to have the pointer 4KB aligned (XENMEM_add_to_physmap is taking a
Xen PFN).
Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
--- Cc: Russell King <linux@arm.linux.org.uk>
Stefano, I've dropped your reviewed-by given I've updated the doc and do
changes to avoid usage of XEN_PAGE_SHIFT
Changes in v4:
- Add Stefano's Reviewed-by
Changes in v3:
- s/MFN/GFN/ base on the new naming
- Use virt_to_gfn to avoid use XEN_PAGE_SHIFT
- Drop Stefano's reviewed-by
- Add some docs in arch/arm/asm/xen/page.h
Julien Grall [Tue, 5 May 2015 15:54:12 +0000 (16:54 +0100)]
xen/privcmd: Add support for Linux 64KB page granularity
The hypercall interface (as well as the toolstack) is always using 4KB
page granularity. When the toolstack is asking for mapping a series of
guest PFN in a batch, it expects to have the page map contiguously in
its virtual memory.
When Linux is using 64KB page granularity, the privcmd driver will have
to map multiple Xen PFN in a single Linux page.
Note that this solution works on page granularity which is a multiple of
4KB.
Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com>
--- Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
I kept the hypercall arguments in remap_data to avoid allocating them on
the stack every time that remap_pte_fn is called.
I will keep like that unless someone is strongly disagree.
Changes in v4:
- s/xen_page_to_pfn/page_to_xen_pfn/ based on the new naming
- Add David's reviewed-by
Changes in v3:
- The function to split a Linux page in mutiple Xen page has
been moved internally. It was the only use (not used anymore in
the balloon) and it's not quite clear what should be the common
interface. Differ the question until someone need to use it.
- s/nr_pfn/numgfns/ to make clear that we are dealing with GFN
- Use DIV_ROUND_UP rather round_up and fix the usage in
xen_xlate_unmap_gfn_range
Julien Grall [Tue, 5 May 2015 12:15:29 +0000 (13:15 +0100)]
net/xen-netback: Make it running on 64KB page granularity
The PV network protocol is using 4KB page granularity. The goal of this
patch is to allow a Linux using 64KB page granularity working as a
network backend on a non-modified Xen.
It's only necessary to adapt the ring size and break skb data in small
chunk of 4KB. The rest of the code is relying on the grant table code.
Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: Wei Liu <wei.liu2@citrix.com>
--- Cc: Ian Campbell <ian.campbell@citrix.com> Cc: netdev@vger.kernel.org
Improvement such as support of 64KB grant is not taken into
consideration in this patch because we have the requirement to run a
Linux using 64KB pages on a non-modified Xen.
Note that I haven't add a comment why the offset is 0 after the first
iteration. See [1] for more details.
[1] https://lkml.org/lkml/2015/8/10/456
Wei, I have kept your reviewed-by because the conflict during rebase
with with 1d5d48523900a4b0f25d6b52f1a93c84bd671186
"xen-netback: require fewer guest Rx slots when not using GSO" was
trivial to resolve. It's basically drop XEN_NETBK_RX_SLOTS_MAX and
replace the new PAGE_SIZE by XEN_PAGE_SIZE. Let me know if it's not
okay.
Changes in v4:
- Add a comment to explain how we compute MAX_XEN_SKB_FRAGS
Changes in v3:
- Fix errors reported by checkpatch.pl
- s/mfn/gfn/ based on the new naming
- gnttab_foreach_grant has been renamed to gnttab_forach_grant_in_range
- The grant callback doesn't allow anymore to use less data. An
helpers has been added in netback to handle this.
Changes in v2:
- Correctly set MAX_GRANT_COPY_OPS and XEN_NETBK_RX_SLOTS_MAX
- Don't use XEN_PAGE_SIZE in handle_frag_list as we coalesce
fragment into a new skb
- Use gnntab_foreach_grant to split a Linux page into grant
net/xen-netfront: Make it running on 64KB page granularity
The PV network protocol is using 4KB page granularity. The goal of this
patch is to allow a Linux using 64KB page granularity using network
device on a non-modified Xen.
It's only necessary to adapt the ring size and break skb data in small
chunk of 4KB. The rest of the code is relying on the grant table code.
Note that we allocate a Linux page for each rx skb but only the first
4KB is used. We may improve the memory usage by extending the size of
the rx skb.
Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com>
--- Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: netdev@vger.kernel.org
Improvement such as support of 64KB grant is not taken into
consideration in this patch because we have the requirement to run a Linux
using 64KB pages on a non-modified Xen.
Tested with workload such as ping, ssh, wget, git... I would happy if
someone give details how to test all the path.
Changes in v4:
- s/gnttab_one_grant/gnttab_for_one_grant/ based on the new naming
- Add David's reviewed-by
Changes in v3:
- Fix errors reported by checkpatch.pl
- s/mfn/gfn/ base on the new naming
- xennet_tx_setup_grant was calling itself resulting an
guest stall when using iperf.
- The grant callback doesn't allow anymore to change the len
(wasn't used here)
- gnttab_foreach_grant has been renamed to gnttab_foreach_grant_in_range
- gnttab_page_grant_foreign_ref has been renamed to
gnttab_foreach_grant_foreign_ref_one
Changes in v2:
- Use gnttab_foreach_grant to split a Linux page in grant
- Fix count slots
Julien Grall [Tue, 5 May 2015 15:25:56 +0000 (16:25 +0100)]
block/xen-blkback: Make it running on 64KB page granularity
The PV block protocol is using 4KB page granularity. The goal of this
patch is to allow a Linux using 64KB page granularity behaving as a
block backend on a non-modified Xen.
It's only necessary to adapt the ring size and the number of request per
indirect frames. The rest of the code is relying on the grant table
code.
Note that the grant table code is allocating a Linux page per grant
which will result to waste 6OKB for every grant when Linux is using 64KB
page granularity. This could be improved by sharing the page between
multiple grants.
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com>
Improvement such as support of 64KB grant is not taken into
consideration in this patch because we have the requirement to run a
Linux using 64KB pages on a non-modified Xen.
This has been tested only with a loop device. I plan to test passing
hard drive partition but I didn't yet convert the swiotlb code.
Changes in v4:
- Add Roger's acked-by
Changes in v3:
- Use DIV_ROUND_UP in INDIRECT_PAGES to avoid a line over 80
characters
block/xen-blkfront: Make it running on 64KB page granularity
The PV block protocol is using 4KB page granularity. The goal of this
patch is to allow a Linux using 64KB page granularity using block
device on a non-modified Xen.
The block API is using segment which should at least be the size of a
Linux page. Therefore, the driver will have to break the page in chunk
of 4K before giving the page to the backend.
When breaking a 64KB segment in 4KB chunks, it is possible that some
chunks are empty. As the PV protocol always require to have data in the
chunk, we have to count the number of Xen page which will be in use and
avoid sending empty chunks.
Note that, a pre-defined number of grants are reserved before preparing
the request. This pre-defined number is based on the number and the
maximum size of the segments. If each segment contains a very small
amount of data, the driver may reserve too many grants (16 grants is
reserved per segment with 64KB page granularity).
Furthermore, in the case of persistent grants we allocate one Linux page
per grant although only the first 4KB of the page will be effectively
in use. This could be improved by sharing the page with multiple grants.
Signed-off-by: Julien Grall <julien.grall@citrix.com> Acked-by: Roger Pau Monné <roger.pau@citrix.com>
--- Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com>
Improvement such as support 64KB grant is not taken into consideration in
this patch because we have the requirement to run a Linux using 64KB page
on a non-modified Xen.
Changes in v4:
- Rebase after d50babbe300eedf33ea5b00a12c5df3a05bd96c7 "
xen-blkfront: introduce blkfront_gather_backend_features()"
- Fix typoes
- Add Roger's acked-by
Changes in v3:
- Use DIV_ROUND_UP in INDIRECT_GREFS
- Split lines over 80 characters whenever it's possible
- s/mfn/gfn/ based on the new naming
- The grant callback doesn't allow anymore to change the len
(wasn't used here).
- gnttab_foreach_grant has been renamed to gnttab_foreach_grant_in_range
- Use gnttab_count_grant to get the number of grants in a sg
- Do some renaming to use the correct variable every time
Changes in v2:
- Use gnttab_foreach_grant to split a Linux page into grant
Julien Grall [Tue, 5 May 2015 15:37:30 +0000 (16:37 +0100)]
xen/events: fifo: Make it running on 64KB granularity
Only use the first 4KB of the page to store the events channel info. It
means that we will waste 60KB every time we allocate page for:
* control block: a page is allocating per CPU
* event array: a page is allocating everytime we need to expand it
I think we can reduce the memory waste for the 2 areas by:
* control block: sharing between multiple vCPUs. Although it will
require some bookkeeping in order to not free the page when the CPU
goes offline and the other CPUs sharing the page still there
* event array: always extend the array event by 64K (i.e 16 4K
chunk). That would require more care when we fail to expand the
event channel.
Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Stefano Stabellini <stefano.stabellini@citrix.com>
--- Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Note I haven't updated the suggestion to reduce the memory waste
after David's email [1]. I can do it if necessary.
Changes in v3:
- Add David and Stefano's reviewed-by
Julien Grall [Mon, 4 May 2015 14:39:08 +0000 (15:39 +0100)]
xen/balloon: Don't rely on the page granularity is the same for Xen and Linux
For ARM64 guests, Linux is able to support either 64K or 4K page
granularity. Although, the hypercall interface is always based on 4K
page granularity.
With 64K page granularity, a single page will be spread over multiple
Xen frame.
To avoid splitting the page into 4K frame, take advantage of the
extent_order field to directly allocate/free chunk of the Linux page
size.
Note that PVMMU is only used for PV guest (which is x86) and the page
granularity is always 4KB. Some BUILD_BUG_ON has been added to ensure
that because the code has not been modified.
Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
--- Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Wei Liu <wei.liu2@citrix.com>
Note that two BUILD_BUG_ON(XEN_PAGE_SIZE != PAGE_SIZE) in code built
for the PV MMU code is kept in order to have at least one even if we
ever decide to drop of code section.
Stefano, I've kept your reviewed-by because the rebase conflict was very
trivial. Let me know if it's not okay.
Changes in v5:
- Add Stefano's reviewed-by
- Fix comment coding style
- Rebase on top of xentip/for-linus-4.4. Got minor conflict
Changes in v4:
- s/xen_page_to_pfn/page_to_xen_pfn/ based on the new naming
- Use the field lru in the page to get a list of pages when
decreasing the memory reservation. It avoids to use a static
array to store the pages (see v3).
- Update comment for EXTENT_ORDER.
Changes in v3:
- Fix errors reported by checkpatch.pl
- s/mfn/gfn/ based on the new naming
- Rather than splitting the page into 4KB chunk, use the
extent_order field to allocate directly a Linux page size. This
is avoid lots of code for no benefits.
Changes in v2:
- Use xen_apply_to_page to split a page in 4K chunk
- It's not necessary to have a smaller frame list. Re-use
PAGE_SIZE
- Convert reserve_additional_memory to use XEN_... macro
Julien Grall [Tue, 5 May 2015 15:58:43 +0000 (16:58 +0100)]
tty/hvc: xen: Use xen page definition
The console ring is always based on the page granularity of Xen.
Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
--- Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.cz> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: linuxppc-dev@lists.ozlabs.org
Changes in v4:
- The ring is always 4K (i.e XEN_PAGE_SIZE), so no need to
map with PAGE_SIZE. This was correctly done in v2 but lost with
the rebase to the "s/mfn/gfn/" series
Changes in v3:
- Some changes has been moved in the series "Use correctly the
Xen memory terminologies in Linux".
- Add Stefano's reviewed-by
Julien Grall [Tue, 5 May 2015 15:38:27 +0000 (16:38 +0100)]
xen/xenbus: Use Xen page definition
All the ring (xenstore, and PV rings) are always based on the page
granularity of Xen.
Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
--- Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Changes in v3:
- Fix errors reported by checkpatch.pl
- s/MFN/GFN base on the new naming
- Add David and Stefano's reviewed-by
Changes in v2:
- Also update the ring mapping function
Julien Grall [Mon, 11 May 2015 12:44:21 +0000 (13:44 +0100)]
xen/biomerge: Don't allow biovec's to be merged when Linux is not using 4KB pages
On ARM all dma-capable devices on a same platform may not be protected
by an IOMMU. The DMA requests have to use the BFN (i.e MFN on ARM) in
order to use correctly the device.
While the DOM0 memory is allocated in a 1:1 fashion (PFN == MFN), grant
mapping will screw this contiguous mapping.
When Linux is using 64KB page granularitary, the page may be split
accross multiple non-contiguous MFN (Xen is using 4KB page
granularity). Therefore a DMA request will likely fail.
Checking that a 64KB page is using contiguous MFN is tedious. For
now, always says that biovec are not mergeable.
Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
--- Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com>
There is some ideas to check whether two biovec could be merged
(see [1]) but it's not critical and can be consider as a performance
improvement.
Changes in v4:
- Fix typoes in the subject
- Add Stefano's reviewed-by
Changes in v3:
- Update commit message
- s/mfn/bfn/ base on the new renaming
- Update TODO
Changes in v2:
- Remove the workaround and check if the Linux page granularity
is the same as Xen or not
Prepare the code to support 64KB page granularity. The first
implementation will use a full Linux page per indirect and persistent
grant. When non-persistent grant is used, each page of a bio request
may be split in multiple grant.
Furthermore, the field page of the grant structure is only used to copy
data from persistent grant or indirect grant. Avoid to set it for other
use case as it will have no meaning given the page will be split in
multiple grant.
Provide 2 functions, to setup indirect grant, the other for bio page.
Signed-off-by: Julien Grall <julien.grall@citrix.com> Acked-by: Roger Pau Monné <roger.pau@citrix.com>
--- Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com>
Changes in v4:
- Add Roger's acked-by
Changes in v3:
- Fix errors reported by checkpatch.pl
- gnttab_page_grant_foreign_access_ref has been renamed to
gnttab_page_grant_foreign_access_ref_one
- Fix compilation by using get_indirect_grant rather than
get_grant (the changes was in a later patch...).
- Make grant_foreign_access static inline
- s/mfn/gfn/ based on the new naming
Julien Grall [Tue, 30 Jun 2015 10:58:51 +0000 (11:58 +0100)]
block/xen-blkfront: Store a page rather a pfn in the grant structure
All the usage of the field pfn are done using the same idiom:
pfn_to_page(grant->pfn)
This will return always the same page. Store directly the page in the
grant to clean up the code.
Signed-off-by: Julien Grall <julien.grall@citrix.com> Acked-by: Roger Pau Monné <roger.pau@citrix.com> Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
--- Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com>
Changes in v4:
- rebase after 7adf12b87f45a77d364464018fb8e9e1ac875152
"xen-blkfront: don't add indirect pages to list when
!feature_persistent"
Changes in v3:
- Use the correct indentation in get_grant. The current
indentation (i.e without this patch) was wrong because it was
using space rather than tabulation.
- Add Roger's acked and Stefano's reviewed
- s/mfn/gfn based on the new naming
Julien Grall [Mon, 29 Jun 2015 16:35:24 +0000 (17:35 +0100)]
block/xen-blkfront: Split blkif_queue_request in 2
Currently, blkif_queue_request has 2 distinct execution path:
- Send a discard request
- Send a read/write request
The function is also allocating grants to use for generating the
request. Although, this is only used for read/write request.
Rather than having a function with 2 distinct execution path, separate
the function in 2. This will also remove one level of tabulation.
Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: Roger Pau Monné <roger.pau@citrix.com>
--- Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com>
Roger, if you really want if can drop the else clause in
blkif_queue_request, IHMO it's more clear here. Although I've kept
your Reviewed-by. Let me know if it's not fine.
Changes in v3:
- Fix errors reported by checkpatch.pl
- Add Roger's Reviewed-by
pfn = page_to_gfn(...) /* Or similar */
gnttab_grant_foreign_access_ref
Replace it by a new helper. Note that when Linux is using a different
page granularity than Xen, the helper only gives access to the first 4KB
grant.
This is useful where drivers are allocating a full Linux page for each
grant.
Also include xen/interface/grant_table.h rather than xen/grant_table.h in
asm/page.h for x86 to fix a compilation issue [1]. Only the former is
useful in order to get the structure definition.
[1] Interdependency between asm/page.h and xen/grant_table.h which result
to page_mfn not being defined when necessary.
Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
--- Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Changes in v3:
- Rename gnttab_page_grant_foreign_access_ref into
gnttab_page_grant_foreign_access_ref_one
- Fix typo in the commit message
- s/mfn/gfn based on the new naming
- Add David and Stefano's reviewed-by
Julien Grall [Fri, 19 Jun 2015 16:49:03 +0000 (17:49 +0100)]
xen/grant: Introduce helpers to split a page into grant
Currently, a grant is always based on the Xen page granularity (i.e
4KB). When Linux is using a different page granularity, a single page
will be split between multiple grants.
The new helpers will be in charge of splitting the Linux page into grants
and call a function given by the caller on each grant.
Also provide an helper to count the number of grants within a given
contiguous region.
Note that the x86/include/asm/xen/page.h is now including
xen/interface/grant_table.h rather than xen/grant_table.h. It's
necessary because xen/grant_table.h depends on asm/xen/page.h and will
break the compilation. Furthermore, only definition in
interface/grant_table.h is required.
Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
--- Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: x86@kernel.org
Changes in v4:
- Typoes
- Rename gnttab_one_grant into gnttab_for_one_grant
- Add Stefano and David's reviewed-by
- s/xen_page_to_pfn/page_to_xen_pfn/ based on the new naming
Changes in v3:
- Fix error reported by checkpatch.pl
- Typoes
- s/pfn/xen_pfn/ in gnttab_foreach_grant
- Drop the possibility to use less data. The complexity is moved
in netback which is the only user
- Rename gnttab_foreach_grant into gnttab_foreach_grant_in_range
- s/offset/start/ in gnttab_count_grant and update the
description of the parameter
- s/mfn/gfn base on the new terminologies
- Add EXPORT_SYMBOL_GPL for gnttab_foreach_grant_in_range
- Use xen_offset_in_page and XEN_PFN_DOWN whenever it's possible
- Fix compilation on x86.
Julien Grall [Mon, 4 May 2015 14:47:16 +0000 (15:47 +0100)]
xen: Add Xen specific page definition
The Xen hypercall interface is always using 4K page granularity on ARM
and x86 architecture.
With the incoming support of 64K page granularity for ARM64 guest, it
won't be possible to re-use the Linux page definition in Xen drivers.
Introduce Xen page definition helpers based on the Linux page
definition. They have exactly the same name but prefixed with
XEN_/xen_ prefix.
Also modify xen_page_to_gfn to use new Xen page definition.
Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
--- Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com>
Changes in v4:
- Typoes
- Rename xen_page_to_pfn to page_to_xen_pfn
Changes in v3:
- Fix errors reported by checkpatch.pl
- Rename pfn to xen_pfn in xen_pfn_to_page
- Add a comment that we assume PAGE_SIZE to be a multiple of
XEN_PAGE_SIZE
- s/MFN/GFN/ according to new naming
- Add Stefano's reviewed-by
Changes in v2:
- Add XEN_PFN_UP
- Add a comment describing the behavior of page_to_pfn
David Vrabel [Wed, 22 Jul 2015 13:50:37 +0000 (14:50 +0100)]
xen/balloon: pre-allocate p2m entries for ballooned pages
Pages returned by alloc_xenballooned_pages() will be used for grant
mapping which will call set_phys_to_machine() (in PV guests).
Ballooned pages are set as INVALID_P2M_ENTRY in the p2m and thus may
be using the (shared) missing tables and a subsequent
set_phys_to_machine() will need to allocate new tables.
Since the grant mapping may be done from a context that cannot sleep,
the p2m entries must already be allocated.
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
David Vrabel [Wed, 22 Jul 2015 13:48:09 +0000 (14:48 +0100)]
x86/xen: export xen_alloc_p2m_entry()
Rename alloc_p2m() to xen_alloc_p2m_entry() and export it.
This is useful for ensuring that a p2m entry is allocated (i.e., not a
shared missing or identity entry) so that subsequent set_phys_to_machine()
calls will require no further allocations.
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
---
v3:
- Make xen_alloc_p2m_entry() a nop on auto-xlate guests.
David Vrabel [Thu, 25 Jun 2015 15:29:18 +0000 (16:29 +0100)]
xen/balloon: use hotplugged pages for foreign mappings etc.
alloc_xenballooned_pages() is used to get ballooned pages to back
foreign mappings etc. Instead of having to balloon out real pages,
use (if supported) hotplugged memory.
This makes more memory available to the guest and reduces
fragmentation in the p2m.
This is only enabled if the xen.balloon.hotplug_unpopulated sysctl is
set to 1. This sysctl defaults to 0 in case the udev rules to
automatically online hotplugged memory do not exist.
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
---
v3:
- Add xen.balloon.hotplug_unpopulated sysctl to enable use of hotplug
for unpopulated pages.
David Vrabel [Thu, 25 Jun 2015 11:10:28 +0000 (12:10 +0100)]
xen/balloon: only hotplug additional memory if required
Now that we track the total number of pages (included hotplugged
regions), it is easy to determine if more memory needs to be
hotplugged.
Add a new BP_WAIT state to signal that the balloon process needs to
wait until kicked by the memory add notifier (when the new section is
onlined by userspace).
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
---
v3:
- Return BP_WAIT if enough sections are already hotplugged.
v2:
- New BP_WAIT status after adding new memory sections.
David Vrabel [Thu, 25 Jun 2015 11:08:20 +0000 (12:08 +0100)]
xen/balloon: rationalize memory hotplug stats
The stats used for memory hotplug make no sense and are fiddled with
in odd ways. Remove them and introduce total_pages to track the total
number of pages (both populated and unpopulated) including those within
hotplugged regions (note that this includes not yet onlined pages).
This will be used in a subsequent commit (xen/balloon: only hotplug
additional memory if required) when deciding whether additional memory
needs to be hotplugged.
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
David Vrabel [Wed, 24 Jun 2015 14:58:42 +0000 (15:58 +0100)]
xen/balloon: find non-conflicting regions to place hotplugged memory
Instead of placing hotplugged memory at the end of RAM (which may
conflict with PCI devices or reserved regions) use allocate_resource()
to get a new, suitably aligned resource that does not conflict.
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
---
v3:
- Remove stale comment.
David Vrabel [Mon, 19 Jan 2015 11:08:05 +0000 (11:08 +0000)]
x86/xen: discard RAM regions above the maximum reservation
During setup, discard RAM regions that are above the maximum
reservation (instead of marking them as E820_UNUSABLE). This allows
hotplug memory to be placed at these addresses.
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
David Vrabel [Thu, 25 Jun 2015 12:18:12 +0000 (13:18 +0100)]
xen/balloon: remove scratch page left overs
Commit 0bb599fd30108883b00c7d4a226eeb49111e6932 (xen: remove scratch
frames for ballooned pages and m2p override) removed the use of the
scratch page for ballooned out pages.
Remove some left over function definitions.
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
David Vrabel [Thu, 25 Jun 2015 15:35:49 +0000 (16:35 +0100)]
mm: memory hotplug with an existing resource
Add add_memory_resource() to add memory using an existing "System RAM"
resource. This is useful if the memory region is being located by
finding a free resource slot with allocate_resource().
Xen guests will make use of this in their balloon driver to hotplug
arbitrary amounts of memory in response to toolstack requests.
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com> Reviewed-by: Tang Chen <tangchen@cn.fujitsu.com>
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Two bugfixes from Andy addressing at least some of the subtle NMI
related wreckage which has been reported by Sasha Levin"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/nmi/64: Fix a paravirt stack-clobbering bug in the NMI code
x86/paravirt: Replace the paravirt nop with a bona fide empty function
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Our first real batch of fixes this release cycle. Nothing really
concerning, and diffstat is a bit inflated due to some DT contents
moving around on STi platforms.
There's a collection of them here:
- A fixup for a build breakage that hits on arm64 allmodconfig in
QCOM SCM firmware drivers
- MMC fixes for OMAP that had quite a bit of breakage this merge
window.
- Misc build/warning fixes on PXA and OMAP
- A couple of minor fixes for Beagleboard X15 which is now starting
to see a few more users in the wild"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: sti: dt: adapt DT to fix probe/bind issues in DRM driver
ARM: dts: fix omap2+ address translation for pbias
firmware: qcom: scm: Add function stubs for ARM64
ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
ARM: omap2plus_defconfig: enable GPIO_PCA953X
ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
ARM: dts: am57xx-beagle-x15: Update Phy supplies
ARM: pxa: balloon3: Fix build error
ARM: dts: Fixup model name for HP t410 dts
ARM: dts: DRA7: fix a typo in ethernet
ARM: omap2plus_defconfig: make PCF857x built-in
ARM: dts: Use ti,pbias compatible string for pbias
ARM: OMAP5: Cleanup options for SoC only build
ARM: DRA7: Select missing options for SoC only build
ARM: OMAP2+: board-generic: Remove stale of_irq macros
ARM: OMAP4+: PM: erratum is used by OMAP5 and DRA7 as well
ARM: dts: omap3-igep: Move eth IRQ pinmux to IGEPv2 common dtsi
ARM: dts: am57xx-beagle-x15: Add wakeup irq for mcp79410
ARM: dts: am335x-phycore-som: Fix mpu voltage
...
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS fixes from Steve French:
"Four fixes from testing at the recent SMB3 Plugfest including two
important authentication ones (one fixes authentication problems to
some popular servers when clock times differ more than two hours
between systems, the other fixes Kerberos authentication for SMB3)"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
fix encryption error checks on mount
[SMB3] Fix sec=krb5 on smb3 mounts
cifs: use server timestamp for ntlmv2 authentication
disabling oplocks/leases via module parm enable_oplocks broken for SMB3
Olof Johansson [Sun, 27 Sep 2015 05:22:31 +0000 (22:22 -0700)]
Merge tag 'omap-for-v4.3/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.3-rc cycle:
- Two more patches to fix most of the MMC regressions with the
PBIAS regulator changes. At least two MMC driver related issues
still seems to remain for omap3 legacy booting and omap4 duovero.
Note that the dts changes depend on a recent regulator fix, and
are based on the regulator commit now in mainline kernel
- Enable autoidle for am43xx clocks to prevent clocks from staying
always on
- Fix i2c5 pinctrl offsets for omap5-uevm
- Enable PCA953X as that's needed for HDMI to work on omap5
- Update phy supplies for beagle x15 beta board
- Use palmas-usb for on beagle x15 to start using the related
driver that recently got merged
* tag 'omap-for-v4.3/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: fix omap2+ address translation for pbias
ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
ARM: omap2plus_defconfig: enable GPIO_PCA953X
ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
ARM: dts: am57xx-beagle-x15: Update Phy supplies
regulator: pbias: program pbias register offset in pbias driver
ARM: omap2plus_defconfig: Enable MUSB DMA support
ARM: DRA752: Add ID detect for ES2.0
ARM: OMAP3: vc: fix 'or' always true warning
ARM: OMAP2+: Fix booting if no timer parent clock is available
ARM: OMAP2+: omap-device: fix race deferred probe of omap_hsmmc vs omap_device_late_init
Pull SCSI target fixes from Nicholas Bellinger:
"This includes a iser-target series from Jenny + Sagi @ Mellanox that
addresses the few remaining active I/O shutdown bugs, along with a
patch to support zero-copy for immediate data payloads that gives a
nice performance improvement for small block WRITEs.
Also included are some recent >= v4.2 regression bug-fixes. The most
notable is a RCU conversion regression for SPC-3 PR registrations, and
recent removal of obsolete RFC-3720 markers that introduced a login
regression bug with MSFT iSCSI initiators.
Thanks to everyone who has been testing + reporting bugs for v4.x"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Avoid OFMarker + IFMarker negotiation
target: Make TCM_WRITE_PROTECT failure honor D_SENSE bit
target: Fix target_sense_desc_format NULL pointer dereference
target: Propigate backend read-only to core_tpg_add_lun
target: Fix PR registration + APTPL RCU conversion regression
iser-target: Skip data copy if all the command data comes as immediate
iser-target: Change the recv buffers posting logic
iser-target: Fix pending connections handling in target stack shutdown sequnce
iser-target: Remove np_ prefix from isert_np members
iser-target: Remove unused variables
iser-target: Put the reference on commands waiting for unsol data
iser-target: remove command with state ISTATE_REMOVE
Merge tag 'usb-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB driver fixes for 4.3-rc3.
There's the usual assortment of new device ids, combined with xhci and
gadget driver fixes. Full details in the shortlog. All of these have
been in linux-next with no reported problems"
* tag 'usb-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (34 commits)
MAINTAINERS: remove amd5536udc USB gadget driver maintainer
USB: whiteheat: fix potential null-deref at probe
xhci: init command timeout timer earlier to avoid deleting it uninitialized
xhci: change xhci 1.0 only restrictions to support xhci 1.1
usb: xhci: exit early in xhci_setup_device() if we're halted or dying
usb: xhci: stop everything on the first call to xhci_stop
usb: xhci: Clear XHCI_STATE_DYING on start
usb: xhci: lock mutex on xhci_stop
xhci: Move xhci_pme_quirk() behind #ifdef CONFIG_PM
xhci: give command abortion one more chance before killing xhci
usb: Use the USB_SS_MULT() macro to get the burst multiplier.
usb: dwc3: gadget: Fix BUG in RT config
usb: musb: fix cppi channel teardown for isoch transfer
usb: phy: isp1301: Export I2C module alias information
usb: gadget: drop null test before destroy functions
usb: gadget: dummy_hcd: in transfer(), return data sent, not limit
usb: gadget: dummy_hcd: fix rescan logic for transfer
usb: gadget: dummy_hcd: fix unneeded else-if condition
usb: gadget: dummy_hcd: emulate sending zlp in packet logic
usb: musb: dsps: fix polling in device-only mode
...
Merge tag 'tty-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fix from Greg KH:
"Here is one serial driver fix for 4.3-rc3 that resolves a module
loading issue due to splitting up of the 8250 driver into smaller
pieces. It's been in linux-next with no reported problems"
* tag 'tty-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: Add missing module license for 8250_base.ko
Merge tag 'char-misc-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here's some tiny char and misc driver fixes that resolve some reported
errors for 4.3-rc3.
All of these have been in linux-next with no problems for a while"
* tag 'char-misc-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
extcon: Fix attached value returned by is_extcon_changed
Drivers: hv: vmbus: fix init_vp_index() for reloading hv_netvsc
mei: fix debugfs files leak on error path
thunderbolt: Allow loading of module on recent Apple MacBooks with thunderbolt 2 controller
1) When we run a tap on netlink sockets, we have to copy mmap'd SKBs
instead of cloning them. From Daniel Borkmann.
2) When converting classical BPF into eBPF, fix the setting of the
source reg to BPF_REG_X. From Tycho Andersen.
3) Fix igmpv3/mldv2 report parsing in the bridge multicast code, from
Linus Lussing.
4) Fix dst refcounting for ipv6 tunnels, from Martin KaFai Lau.
5) Set NLM_F_REPLACE flag properly when replacing ipv6 routes, from
Roopa Prabhu.
6) Add some new cxgb4 PCI device IDs, from Hariprasad Shenai.
7) Fix headroom tests and SKB leaks in ipv6 fragmentation code, from
Florian Westphal.
8) Check DMA mapping errors in bna driver, from Ivan Vecera.
9) Several 8139cp bug fixes (dev_kfree_skb_any in interrupt context,
misclearing of interrupt status in TX timeout handler, etc.) from
David Woodhouse.
10) In tipc, reset SKB header pointer after skb_linearize(), from Erik
Hugne.
11) Fix autobind races et al. in netlink code, from Herbert Xu with
help from Tejun Heo and others.
12) Missing SET_NETDEV_DEV in sunvnet driver, from Sowmini Varadhan.
13) Fix various races in timewait timer and reqsk_queue_hadh_req, from
Eric Dumazet.
14) Fix array overruns in mac80211, from Johannes Berg and Dan
Carpenter.
15) Fix data race in rhashtable_rehash_one(), from Dmitriy Vyukov.
16) Fix race between poll_one_napi and napi_disable, from Neil Horman.
17) Fix byte order in geneve tunnel port config, from John W Linville.
18) Fix handling of ARP replies over lightweight tunnels, from Jiri
Benc.
19) We can loop when fib rule dumps cross multiple SKBs, fix from Wilson
Kok and Roopa Prabhu.
20) Several reference count handling bug fixes in the PHY/MDIO layer
from Russel King.
21) Fix lockdep splat in ppp_dev_uninit(), from Guillaume Nault.
22) Fix crash in icmp_route_lookup(), from David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net: Fix panic in icmp_route_lookup
net: update docbook comment for __mdiobus_register()
ppp: fix lockdep splat in ppp_dev_uninit()
net: via/Kconfig: GENERIC_PCI_IOMAP required if PCI not selected
phy: marvell: add link partner advertised modes
net: fix net_device refcounting
phy: add phy_device_remove()
phy: fixed-phy: properly validate phy in fixed_phy_update_state()
net: fix phy refcounting in a bunch of drivers
of_mdio: fix MDIO phy device refcounting
phy: add proper phy struct device refcounting
phy: fix mdiobus module safety
net: dsa: fix of_mdio_find_bus() device refcount leak
phy: fix of_mdio_find_bus() device refcount leak
ip6_tunnel: Reduce log level in ip6_tnl_err() to debug
ip6_gre: Reduce log level in ip6gre_err() to debug
fib_rules: fix fib rule dumps across multiple skbs
bnx2x: byte swap rss_key to comply to Toeplitz specs
net: revert "net_sched: move tp->root allocation into fw_init()"
lwtunnel: remove source and destination UDP port config option
...
Prior to the VRF change the oif was not set in the flow struct, so the
VRF support should really have only added the vrf_master_ifindex lookup.
Fixes: 613d09b30f8b ("net: Use VRF device index for lookups on TX") Cc: Andrey Melnikov <temnota.am@gmail.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
MAINTAINERS: remove amd5536udc USB gadget driver maintainer
Thomas can no longer work on the driver, so he asked me to mark the
MAINTAINER entry as "Orphan" with the hope that someone else would
someday pick it up.
Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge branch 'for-4.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull another cgroup fix from Tejun Heo:
"The cgroup writeback support got inadvertently enabled for traditional
hierarchies revealing two regressions which are currently being worked
on. It shouldn't have been enabled on traditional hierarchies, so
disable it on them. This is enough to make the regressions go away
for people who aren't experimenting with cgroup"
* 'for-4.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup, writeback: don't enable cgroup writeback on traditional hierarchies
ppp_dev_uninit() locks all_ppp_mutex while under rtnl mutex protection.
ppp_create_interface() must then lock these mutexes in that same order
to avoid possible deadlock.
net: via/Kconfig: GENERIC_PCI_IOMAP required if PCI not selected
The builds of allmodconfig of avr32 is failing with:
drivers/net/ethernet/via/via-rhine.c:1098:2: error: implicit declaration
of function 'pci_iomap' [-Werror=implicit-function-declaration]
drivers/net/ethernet/via/via-rhine.c:1119:2: error: implicit declaration
of function 'pci_iounmap' [-Werror=implicit-function-declaration]
The generic empty pci_iomap and pci_iounmap is used only if CONFIG_PCI
is not defined and CONFIG_GENERIC_PCI_IOMAP is defined.
Add GENERIC_PCI_IOMAP in the dependency list for VIA_RHINE as we are
getting build failure when CONFIG_PCI and CONFIG_GENERIC_PCI_IOMAP both
are not defined.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 23 Sep 2015 23:07:17 +0000 (00:07 +0100)]
phy: marvell: add link partner advertised modes
Read the standard link partner advertisment registers and store it in
phydev->lp_advertising, so ethtool can report this information to
userspace via ethtool. Zero it as per genphy if autonegotiation is
disabled. Tested with a Marvell 88E1512 PHY.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This is an assorted set I've been queuing up:
Jeff Mahoney tracked down a tricky one where we ended up starting IO
on the wrong mapping for special files in btrfs_evict_inode. A few
people reported this one on the list.
Filipe found (and provided a test for) a difficult bug in reading
compressed extents, and Josef fixed up some quota record keeping with
snapshot deletion. Chandan killed off an accounting bug during DIO
that lead to WARN_ONs as we freed inodes"
* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: keep dropped roots in cache until transaction commit
Btrfs: Direct I/O: Fix space accounting
btrfs: skip waiting on ordered range for special files
Btrfs: fix read corruption of compressed and shared extents
Btrfs: remove unnecessary locking of cleaner_mutex to avoid deadlock
Btrfs: don't initialize a space info as full to prevent ENOSPC
Merge tag 'nfs-for-4.3-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable patches:
- fix v4.2 SEEK on files over 2 gigs
- Fix a layout segment reference leak when pNFS I/O falls back to inband I/O.
- Fix recovery of recalled read delegations
Bugfixes:
- Fix a case where NFSv4 fails to send CLOSE after a server reboot
- Fix sunrpc to wait for connections to complete before retrying
- Fix sunrpc races between transport connect/disconnect and shutdown
- Fix an infinite loop when layoutget fail with BAD_STATEID
- nfs/filelayout: Fix NULL reference caused by double freeing of fh_array
- Fix a bogus WARN_ON_ONCE() in O_DIRECT when layout commit_through_mds is set
- Fix layoutreturn/close ordering issues"
* tag 'nfs-for-4.3-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS41: make close wait for layoutreturn
NFS: Skip checking ds_cinfo.buckets when lseg's commit_through_mds is set
NFSv4.x/pnfs: Don't try to recover stateids twice in layoutget
NFSv4: Recovery of recalled read delegations is broken
NFS: Fix an infinite loop when layoutget fail with BAD_STATEID
NFS: Do cleanup before resetting pageio read/write to mds
SUNRPC: xs_sock_mark_closed() does not need to trigger socket autoclose
SUNRPC: Lock the transport layer on shutdown
nfs/filelayout: Fix NULL reference caused by double freeing of fh_array
SUNRPC: Ensure that we wait for connections to complete before retrying
SUNRPC: drop null test before destroy functions
nfs: fix v4.2 SEEK on files over 2 gigs
SUNRPC: Fix races between socket connection and destroy code
nfs: fix pg_test page count calculation
Failing to send a CLOSE if file is opened WRONLY and server reboots on a 4.x mount
Merge tag 'sound-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This ended up with a larger set of fixes than wished, unfortunately.
As diffstat shows, the majority of changes are for various ASoC
drivers (Realtek, Wolfson codec drivers, etc), in addition to a couple
of HD-audio regression fixes. All these are reasonably small and
nothing to scare much"
* tag 'sound-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (29 commits)
ALSA: hda - Disable power_save_node for Thinkpads
ALSA: hda/tegra - async probe for avoiding module loading deadlock
ASoC: rt5645: Prevent the pop sound in case of playback and the jack is plugging
ASoC: rt5645: Increase the delay time to remove the pop sound
ASoC: rt5645: Use the type SOC_DAPM_SINGLE_AUTODISABLE to prevent the weird sound in runtime of power up
ASoC: pxa: pxa2xx-ac97: fix dma requestor lines
MAINTAINERS: Update website and git repo for Wolfson Microelectronics
ASoC: fsl_ssi: Fix checking of dai format for AC97 mode
ASoC: wm0010: fix error path
ASoC: wm0010: fix memory leak
ASoC: wm8960: correct the max register value of mic boost pga
ASoC: wm8962: remove 64k sample rate support
ASoC: davinci-mcasp: Fix devm_kasprintf format string
ASoC: fix broken pxa SoC support
ASoC: davinci-mcasp: Set .symmetric_rates = 1 in snd_soc_dai_driver
ASoC: au1x: psc-i2s: Fix unused variable 'ret' warning
ASoC: SPEAr: Make SND_SPEAR_SOC select SND_SOC_GENERIC_DMAENGINE_PCM
ASoC: mediatek: Increase periods_min in capture
ASoC: davinci-mcasp: Revise the FIFO threshold calculation
ASoC: wm8960: correct gain value for input PGA and add microphone PGA
...
Merge tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for things we merged for v4.3 (VPD, MSI, and bridge
window management), and a new Renesas R8A7794 SoC device ID.
Details:
Resource management:
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn
Helgaas)
MSI:
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Miscellaneous:
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)"
* tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: rcar: Add R8A7794 support
PCI: Use function 0 VPD for identical functions, regular VPD for others
PCI: Fix devfn for VPD access through function 0
PCI/MSI: Fix MSI IRQ domains for VFs on virtual buses
PCI: Clear IORESOURCE_UNSET when clipping a bridge window
PCI: Revert "PCI: Call pci_read_bridge_bases() from core instead of arch code"
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"AMD fixes for bugs introduced in the 4.2 merge window, and a few PPC
bug fixes too"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: disable halt_poll_ns as default for s390x
KVM: x86: fix off-by-one in reserved bits check
KVM: x86: use correct page table format to check nested page table reserved bits
KVM: svm: do not call kvm_set_cr0 from init_vmcb
KVM: x86: trap AMD MSRs for the TSeg base and mask
KVM: PPC: Book3S: Take the kvm->srcu lock in kvmppc_h_logical_ci_load/store()
KVM: PPC: Book3S HV: Pass the correct trap argument to kvmhv_commence_exit
KVM: PPC: Book3S HV: Fix handling of interrupted VCPUs
kvm: svm: reset mmu on VCPU reset
Merge tag 'powerpc-4.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Wire up sys_membarrier()
- cxl: Fix lockdep warning while creating afu_err_buff from Vaibhav
* tag 'powerpc-4.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
cxl: Fix lockdep warning while creating afu_err_buff attribute
powerpc: Wire up sys_membarrier()
We observed some performance degradation on s390x with dynamic
halt polling. Until we can provide a proper fix, let's enable
halt_poll_ns as default only for supported architectures.
Architectures are now free to set their own halt_poll_ns
default value.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Tue, 22 Sep 2015 08:15:59 +0000 (10:15 +0200)]
KVM: x86: fix off-by-one in reserved bits check
29ecd6601904 ("KVM: x86: avoid uninitialized variable warning",
2015-09-06) introduced a not-so-subtle problem, which probably
escaped review because it was not part of the patch context.
Before the patch, leaf was always equal to iterator.level. After,
it is equal to iterator.level - 1 in the call to is_shadow_zero_bits_set,
and when is_shadow_zero_bits_set does another "-1" the check on
reserved bits becomes incorrect. Using "iterator.level" in the call
fixes this call trace:
Paolo Bonzini [Tue, 22 Sep 2015 21:02:14 +0000 (23:02 +0200)]
KVM: x86: use correct page table format to check nested page table reserved bits
Intel CPUID on AMD host or vice versa is a weird case, but it can
happen. Handle it by checking the host CPU vendor instead of the
guest's in reset_tdp_shadow_zero_bits_mask. For speed, the
check uses the fact that Intel EPT has an X (executable) bit while
AMD NPT has NX.
Paolo Bonzini [Mon, 21 Sep 2015 05:46:55 +0000 (07:46 +0200)]
KVM: svm: do not call kvm_set_cr0 from init_vmcb
kvm_set_cr0 may want to call kvm_zap_gfn_range and thus access the
memslots array (SRCU protected). Using a mini SRCU critical section
is ugly, and adding it to kvm_arch_vcpu_create doesn't work because
the VMX vcpu_create callback calls synchronize_srcu.
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
1 lock held by qemu-system-i38/17000:
#0: (&(&kvm->mmu_lock)->rlock){+.+...}, at: kvm_zap_gfn_range+0x24/0x1a0 [kvm]
This patch fixes a v4.2+ regression introduced by commit c04a6091
that removed support for obsolete sync-and-steering markers usage
as originally defined in RFC-3720.
The regression would involve attempting to send OFMarker=No +
IFMarker=No keys during opertional negotiation login phase,
including when initiators did not actually propose these keys.
The result for MSFT iSCSI initiators would be random junk in
TCP stream after the last successful login request was been sent
signaling the move to full feature phase (FFP) operation.
To address this bug, go ahead and avoid negotiating these keys
by default unless the initiator explicitly proposes them, but
still respond to them with 'No' if they are proposed.
This patch allows target_sense_desc_format() to be called without a
valid se_device pointer, which can occur during an early exception
ahead of transport_lookup_cmd_lun() setting up se_cmd->se_device.
This addresses a v4.3-rc1 specific NULL pointer dereference
regression introduced by commit 4e4937e8.
Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target: Propigate backend read-only to core_tpg_add_lun
This patch adds a DF_READ_ONLY flag that is used by IBLOCK to
signal when a backend has been set to read-only mode, in order
to propigate read-only status up to core_tpg_add_lun() for all
future LUN fabric exports.
With this is place, existing emulation for reporting read-only
in spc_emulate_modesense() and normal transport_lookup_cmd_lun()
TCM_WRITE_PROTECTED status checking just works as expected.
Reported-by: Joeue Deng <joeue404@gmail.com> Reported-by: Andy Grover <agrover@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a v4.2+ regression introduced by commit 79dc9c9e86
where lookup of t10_pr_registration->pr_reg_deve and associated
->pr_kref get was missing from __core_scsi3_do_alloc_registration(),
which is responsible for setting DEF_PR_REG_ACTIVE.
This would result in REGISTER operations completing successfully,
but subsequent core_scsi3_pr_seq_non_holder() checking would fail
with !DEF_PR_REG_ACTIVE -> RESERVATION CONFLICT status.
Update __core_scsi3_add_registration() to drop ->pr_kref reference
after registration and any optional ALL_TG_PT=1 processing has
completed. Update core_scsi3_decode_spec_i_port() to release
the new parent local_pr_reg->pr_kref as well.
Also, update __core_scsi3_check_aptpl_registration() to perform
the same target_nacl_find_deve() lookup + ->pr_kref get, now that
__core_scsi3_add_registration() expects to drop the reference.
Finally, since there are cases when se_dev_entry->se_lun_acl can
still be dereferenced in core_scsi3_lunacl_undepend_item() while
holding ->pr_kref, go ahead and move explicit rcu_assign_pointer()
NULL assignments within core_disable_device_list_for_node() until
after orig->pr_comp finishes.
Reported-by: Scott L. Lykens <scott@lykens.org> Tested-by: Scott L. Lykens <scott@lykens.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Lee Duncan <lduncan@suse.com> Cc: <stable@vger.kernel.org> # v4.2+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
David S. Miller [Fri, 25 Sep 2015 06:04:53 +0000 (23:04 -0700)]
Merge branch 'phy-mdio-refcnt'
Russell King says:
====================
Phy, mdiobus, and netdev struct device fixes
The third version of this series fixes the build error which David
identified, and drops the broken changes for the Cavium Thunger BGX
ethernet driver as this driver requires some complex changes to
resolve the leakage - and this is best done by people who can test
the driver.
Compared to v2, the only patch which has changed is patch 6
"net: fix phy refcounting in a bunch of drivers"
I _think_ I've been able to build-test all the drivers touched by
that patch to some degree now, though several of them needed the
Kconfig hacked to allow it (not all had || COMPILE_TEST clause on
their dependencies.)
Previous cover letters below:
This is the second version of the series, with the comments David had
on the first patch fixed up. Original series description with updated
diffstat below.
While looking at the DSA code, I noticed we have a
of_find_net_device_by_node(), and it looks like users of that are
similarly buggy - it looks like net/dsa/dsa.c is the only user. Fix
that too.
Hi,
While looking at the phy code, I identified a number of weaknesses
where refcounting on device structures was being leaked, where
modules could be removed while in-use, and where the fixed-phy could
end up having unintended consequences caused by incorrect calls to
fixed_phy_update_state().
This patch series resolves those issues, some of which were discovered
with testing on an Armada 388 board. Not all patches are fully tested,
particularly the one which touches several network drivers.
When resolving the struct device refcounting problems, several different
solutions were considered before settling on the implementation here -
one of the considerations was to avoid touching many network drivers.
The solution here is:
phy_attach*() - takes a refcount
phy_detach*() - drops the phy_attach refcount
Provided drivers always attach and detach their phys, which they should
already be doing, this should change nothing, even if they leak a refcount.
of_phy_find_device() and of_* functions which use that take
a refcount. Arrange for this refcount to be dropped once
the phy is attached.
This is the reason why the previous change is important - we can't drop
this refcount taken by of_phy_find_device() until something else holds
a reference on the device. This resolves the leaked refcount caused by
using of_phy_connect() or of_phy_attach().
Even without the above changes, these drivers are leaking by calling
of_phy_find_device(). These drivers are addressed by adding the
appropriate release of that refcount.
The mdiobus code also suffered from the same kind of leak, but thankfully
this only happened in one place - the mdio-mux code.
I also found that the try_module_get() in the phy layer code was utterly
useless: phydev->dev.driver was guaranteed to always be NULL, so
try_module_get() was always being called with a NULL argument. I proved
this with my SFP code, which declares its own MDIO bus - the module use
count was never incremented irrespective of how I set the MDIO bus up.
This allowed the MDIO bus code to be removed from the kernel while there
were still PHYs attached to it.
One other bug was discovered: while using in-band-status with mvneta, it
was found that if a real phy is attached with in-band-status enabled,
and another ethernet interface is using the fixed-phy infrastructure, the
interface using the fixed-phy infrastructure is configured according to
the other interface using the in-band-status - which is caused by the
fixed-phy code not verifying that the phy_device passed in is actually
a fixed-phy device, rather than a real MDIO phy.
Lastly, having mdio_bus reversing phy_device_register() internals seems
like a layering violation - it's trivial to move that code to the phy
device layer.
====================
Tested-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 24 Sep 2015 19:36:33 +0000 (20:36 +0100)]
net: fix net_device refcounting
of_find_net_device_by_node() uses class_find_device() internally to
lookup the corresponding network device. class_find_device() returns
a reference to the embedded struct device, with its refcount
incremented.
Add a comment to the definition in net/core/net-sysfs.c indicating the
need to drop this refcount, and fix the DSA code to drop this refcount
when the OF-generated platform data is cleaned up and freed. Also
arrange for the ref to be dropped when handling errors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 24 Sep 2015 19:36:28 +0000 (20:36 +0100)]
phy: add phy_device_remove()
Add a phy_device_remove() function to complement phy_device_register(),
which undoes the effects of phy_device_register() by removing the phy
device from visibility, but not freeing it.
This allows these details to be moved out of the mdio bus code into
the phy code where this action belongs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 24 Sep 2015 19:36:23 +0000 (20:36 +0100)]
phy: fixed-phy: properly validate phy in fixed_phy_update_state()
Validate that the phy_device passed into fixed_phy_update_state() is a
fixed-phy device before walking the list of phys for a fixed phy at the
same address.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 24 Sep 2015 19:36:18 +0000 (20:36 +0100)]
net: fix phy refcounting in a bunch of drivers
of_phy_find_device() increments the phy struct device refcount, which
we need to properly balance. Add code to network drivers using this
function to ensure that the struct device refcount is correctly
balanced.
For xgene, looking back in the history, we should be able to use
of_phy_connect() with a zero flags argument for the DT case as this is
how the driver used to operate prior to de7b5b3d790a ("net: eth: xgene:
change APM X-Gene SoC platform ethernet to support ACPI").
This leaves the Cavium Thunder BGX unfixed; fixing this driver is a
complicated task, one which the maintainers need to be involved with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 24 Sep 2015 19:36:13 +0000 (20:36 +0100)]
of_mdio: fix MDIO phy device refcounting
bus_find_device() is defined as:
* This is similar to the bus_for_each_dev() function above, but it
* returns a reference to a device that is 'found' for later use, as
* determined by the @match callback.
and it does indeed return a reference-counted pointer to the device:
while ((dev = next_device(&i)))
if (match(dev, data) && get_device(dev))
^^^^^^^^^^^^^^^
break;
klist_iter_exit(&i);
return dev;
What that means is that when we're done with the struct device, we must
drop that reference. Neither of_phy_connect() nor of_phy_attach() did
this when phy_connect_direct() or phy_attach_direct() failed.
With our previous patch, phy_connect_direct() and phy_attach_direct()
take a new refcount on the phy device when successful, so we can drop
our local reference immediatley after these functions, whether or not
they succeeded.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 24 Sep 2015 19:36:08 +0000 (20:36 +0100)]
phy: add proper phy struct device refcounting
Take a refcount on the phy struct device when the phy device is attached
to a network device, and drop it after it's detached. This ensures that
a refcount is held on the phy device while the device is being used by
a network device, thereby preventing the phy_device from being
unexpectedly kfree()'d by phy_device_release().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 24 Sep 2015 19:36:02 +0000 (20:36 +0100)]
phy: fix mdiobus module safety
Re-implement the mdiobus module refcounting to ensure that we actually
ensure that the mdiobus module code does not go away while we might call
into it.
The old scheme using bus->dev.driver was buggy, because bus->dev is a
class device which never has a struct device_driver associated with it,
and hence the associated code trying to obtain a refcount did nothing
useful.
Instead, take the approach that other subsystems do: pass the module
when calling mdiobus_register(), and record that in the mii_bus struct.
When we need to increment the module use count in the phy code, use
this stored pointer. When the phy is deteched, drop the module
refcount, remembering that the phy device might go away at that point.
This doesn't stop the mii_bus going away while there are in-use phys -
it merely stops the underlying code vanishing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Current users of of_mdio_find_bus() leak a struct device refcount, as
they fail to clean up the reference obtained inside class_find_device().
Fix the DSA code to properly refcount the returned MDIO bus by:
1. taking a reference on the struct device whenever we assign it to
pd->chip[x].host_dev.
2. dropping the reference when we overwrite the existing reference.
3. dropping the reference when we free the data structure.
4. dropping the initial reference we obtained after setting up the
platform data structure, or on failure.
In step 2 above, where we obtain a new MDIO bus, there is no need to
take a reference on it as we would only have to drop it immediately
after assignment again, iow:
put_device(cd->host_dev); /* drop original assignment ref */
cd->host_dev = get_device(&mdio_bus_switch->dev); /* get our ref */
put_device(&mdio_bus_switch->dev); /* drop of_mdio_find_bus ref */
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 24 Sep 2015 19:35:52 +0000 (20:35 +0100)]
phy: fix of_mdio_find_bus() device refcount leak
of_mdio_find_bus() leaks a struct device refcount, caused by using
class_find_device() and not realising that the device reference has
its refcount incremented:
* Note, you will need to drop the reference with put_device() after use.
...
while ((dev = class_dev_iter_next(&iter))) {
if (match(dev, data)) {
get_device(dev);
break;
}
Update the comment, and arrange for the phy code to drop this refcount
when disposing of a reference to it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fixes from Zhang Rui:
- Power allocator governor changes to allow binding on thermal zones
with missing power estimates information. From Javi Merino.
- Add compile test flags on thermal drivers that allow it without
producing compilation errors. From Eduardo Valentin.
- Fixes around memory allocation on cpu_cooling. From Javi Merino.
- Fix on db8500 cpufreq code to allow autoload. From Luis de
Bethencourt.
- Maintainer entries for cpu cooling device
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: power_allocator: exit early if there are no cooling devices
thermal: power_allocator: don't require tzp to be present for the thermal zone
thermal: power_allocator: relax the requirement of two passive trip points
thermal: power_allocator: relax the requirement of a sustainable_power in tzp
thermal: Add a function to get the minimum power
thermal: cpu_cooling: free power table on error or when unregistering
thermal: cpu_cooling: don't call kcalloc() under rcu_read_lock
thermal: db8500_cpufreq_cooling: Fix module autoload for OF platform driver
thermal: cpu_cooling: Add MAINTAINERS entry
thermal: ti-soc: Kconfig fix to avoid menu showing wrongly
thermal: ti-soc: allow compile test
thermal: qcom_spmi: allow compile test
thermal: exynos: allow compile test
thermal: armada: allow compile test
thermal: dove: allow compile test
thermal: kirkwood: allow compile test
thermal: rockchip: allow compile test
thermal: spear: allow compile test
thermal: hisi: allow compile test
thermal: Fix thermal_zone_of_sensor_register to match documentation
Merge tag 'devicetree-fixes-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- Silence bogus warning for of_irq_parse_pci
- Fix typo in ARM idle-states binding doc and dts files
- Various minor binding documentation updates
* tag 'devicetree-fixes-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
Documentation: arm: Fix typo in the idle-states bindings examples
gpio: mention in DT binding doc that <name>-gpio is deprecated
of_pci_irq: Silence bogus "of_irq_parse_pci() failed ..." messages.
devicetree: bindings: Extend the bma180 bindings with bma250 info
of: thermal: Mark cooling-*-level properties optional
of: thermal: Fix inconsitency between cooling-*-state and cooling-*-level
Docs: dt: add #msi-cells to GICv3 ITS binding
of: add vendor prefix for Socionext Inc.
ARM: sti: dt: adapt DT to fix probe/bind issues in DRM driver
STI drm drivers probe and bind using component framework was incorrect.
In addition to drivers fix DT update is needed to make all sub-components
become childs of sti-display-subsystem.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com> Signed-off-by: Olof Johansson <olof@lixom.net>
ARM: dts: fix omap2+ address translation for pbias
"ARM: dts: <omap2/omap4/omap5/dra7>: add minimal l4 bus
layout with control module support" moved pbias_regulator dt node
from being a child node of ocp to be the child node of
'syscon'. Since 'syscon' doesn't have the 'ranges' property,
address translation fails while trying to convert the address
to resource. Fix it here by populating 'ranges' property in
syscon dt node.
Fixes: 72b10ac00eb1 ("ARM: dts: omap24xx: add minimal l4 bus
layout with control module support")
Fixes: 7415b0b4c645 ("ARM: dts: omap4: add minimal l4 bus layout
with control module support")
Fixes: ed8509edddeb ("ARM: dts: omap5: add minimal l4 bus
layout with control module support")
Fixes: d919501feffa ("ARM: dts: dra7: add minimal l4 bus
layout with control module support")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[tony@atomide.com: fixed omap3 pbias to work] Signed-off-by: Tony Lindgren <tony@atomide.com>
Matt Bennett [Thu, 24 Sep 2015 23:01:47 +0000 (11:01 +1200)]
ip6_tunnel: Reduce log level in ip6_tnl_err() to debug
Currently error log messages in ip6_tnl_err are printed at 'warn'
level. This is different to other tunnel types which don't print
any messages. These log messages don't provide any information that
couldn't be deduced with networking tools. Also it can be annoying
to have one end of the tunnel go down and have the logs fill with
pointless messages such as "Path to destination invalid or inactive!".
This patch reduces the log level of these messages to 'dbg' level to
bring the visible behaviour into line with other tunnel types.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation: arm: Fix typo in the idle-states bindings examples
The idle-states bindings mandate that the entry-method string
in the idle-states node must be "psci" for ARM v8 64-bit systems,
but the examples in the bindings report a wrong entry-method string.
Owing to this typo, some dts in the kernel wrongly defined the
entry-method property, since they likely cut and pasted the example
definition without paying attention to the bindings definitions.
This patch fixes the typo in the DT idle states bindings examples and
respective dts in the kernel so that the bindings and related dts
files are made compliant.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Howard Chen <howard.chen@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Rob Herring <robh@kernel.org>
gpio: mention in DT binding doc that <name>-gpio is deprecated
The gpiolib supports parsing DT properties of the form <name>-gpio but it
was only added for compatibility with older DT bindings that got it wrong
and should not be used in newer bindings.
The commit that added support for this was:
dd34c37aa3e8 ("gpio: of: Allow -gpio suffix for property names")
but didn't update the documentation to explain this so it's been a source
of confusion. So let's make this clear in the GPIO DT binding doc.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Rob Herring <robh@kernel.org>
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Most of the GPU drivers people were at XDC last week, so I didn't get
much to send, so I let it rollover until this week.
Also Alex was away for 3 weeks so amdgpu/radeon got a bit more stuff
than usual in one go.
I've been trying to figure out some 4.2 issues with i915 still (that
are fixed in 4.3, but bisecting ends up in a merge commit). Hopefully
next week I or i915 people can work that out"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (46 commits)
drm: Allow also control clients to check the drm version
drm/vmwgfx: Fix uninitialized return in vmw_kms_helper_dirty()
drm/vmwgfx: Fix uninitialized return in vmw_cotable_unbind()
drm/layerscape: fix handling fsl_dcu_drm_plane_index result
drm/mgag200: Fix driver_load error handling
drm/mgag200: Fix error handling paths in fbdev driver
drm/qxl: only report first monitor as connected if we have no state
drm/radeon: add quirk for MSI R7 370
drm/amdgpu: Sprinkle drm_modeset_lock_all to appease locking checks
drm/radeon: Sprinkle drm_modeset_lock_all to appease locking checks
drm/amdgpu: sync ce and me with SWITCH_BUFFER(2)
drm/amdgpu: integer overflow in amdgpu_mode_dumb_create()
drm/amdgpu: info leak in amdgpu_gem_metadata_ioctl()
drm/amdgpu: integer overflow in amdgpu_info_ioctl()
drm/amdgpu: unwind properly in amdgpu_cs_parser_init()
drm/amdgpu: Fix max_vblank_count value for current display engines
drm/amdgpu: use kmemdup rather than duplicating its implementation
drm/amdgpu: fix UVD suspend and resume for VI APU
drm/amdgpu: fix the UVD suspend sequence order
drm/amdgpu: make UVD handle checking more strict
...
David S. Miller [Thu, 24 Sep 2015 22:36:20 +0000 (15:36 -0700)]
Merge tag 'mac80211-for-davem-2015-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just two small fixes:
* VHT MCS mask array overrun, reported by Dan Carpenter
* reset CQM history to always get a notification, from Sara Sharon
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Bennett [Wed, 23 Sep 2015 04:58:31 +0000 (16:58 +1200)]
ip6_gre: Reduce log level in ip6gre_err() to debug
Currently error log messages in ip6gre_err are printed at 'warn'
level. This is different to most other tunnel types which don't
print any messages. These log messages don't provide any information
that couldn't be deduced with networking tools. Also it can be annoying
to have one end of the tunnel go down and have the logs fill with
pointless messages such as "Path to destination invalid or inactive!".
This patch reduces the log level of these messages to 'dbg' level to
bring the visible behaviour into line with other tunnel types.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
Wilson Kok [Wed, 23 Sep 2015 04:40:22 +0000 (21:40 -0700)]
fib_rules: fix fib rule dumps across multiple skbs
dump_rules returns skb length and not error.
But when family == AF_UNSPEC, the caller of dump_rules
assumes that it returns an error. Hence, when family == AF_UNSPEC,
we continue trying to dump on -EMSGSIZE errors resulting in
incorrect dump idx carried between skbs belonging to the same dump.
This results in fib rule dump always only dumping rules that fit
into the first skb.
This patch fixes dump_rules to return error so that we exit correctly
and idx is correctly maintained between skbs that are part of the
same dump.
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Williamson [Wed, 16 Sep 2015 04:24:46 +0000 (22:24 -0600)]
PCI: Use function 0 VPD for identical functions, regular VPD for others
932c435caba8 ("PCI: Add dev_flags bit to access VPD through function 0")
added PCI_DEV_FLAGS_VPD_REF_F0. Previously, we set the flag on every
non-zero function of quirked devices. If a function turned out to be
different from function 0, i.e., it had a different class, vendor ID, or
device ID, the flag remained set but we didn't make VPD accessible at all.
Flip this around so we only set PCI_DEV_FLAGS_VPD_REF_F0 for functions that
are identical to function 0, and allow regular VPD access for any other
functions.
[bhelgaas: changelog, stable tag] Fixes: 932c435caba8 ("PCI: Add dev_flags bit to access VPD through function 0") Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Bjorn Helgaas <helgaas@kernel.org> Acked-by: Myron Stowe <myron.stowe@redhat.com> Acked-by: Mark Rustad <mark.d.rustad@intel.com> CC: stable@vger.kernel.org
Alex Williamson [Tue, 15 Sep 2015 17:17:21 +0000 (11:17 -0600)]
PCI: Fix devfn for VPD access through function 0
Commit 932c435caba8 ("PCI: Add dev_flags bit to access VPD through function
0") passes PCI_SLOT(devfn) for the devfn parameter of pci_get_slot().
Generally this works because we're fairly well guaranteed that a PCIe
device is at slot address 0, but for the general case, including
conventional PCI, it's incorrect. We need to get the slot and then convert
it back into a devfn.
Fixes: 932c435caba8 ("PCI: Add dev_flags bit to access VPD through function 0") Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Bjorn Helgaas <helgaas@kernel.org> Acked-by: Myron Stowe <myron.stowe@redhat.com> Acked-by: Mark Rustad <mark.d.rustad@intel.com> CC: stable@vger.kernel.org
Alex Williamson [Fri, 18 Sep 2015 21:08:54 +0000 (15:08 -0600)]
PCI/MSI: Fix MSI IRQ domains for VFs on virtual buses
SR-IOV creates a virtual bus where bus->self is NULL. When we add VFs and
scan for an MSI domain, pci_set_bus_msi_domain() dereferences bus->self,
which causes a kernel NULL pointer dereference oops.
Scan up to the parent bus until we find a real bridge where we can get the
MSI domain.
[bhelgaas: changelog] Fixes: 44aa0c657e3e ("PCI/MSI: Add hooks to populate the msi_domain field") Tested-by: Joerg Roedel <joro@8bytes.org> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Bjorn Helgaas <helgaas@kernel.org> Acked-by: Marc Zyngier <marc.zyngier@arm.com>
It is mostly a non issue, unless we want to mix different NIC
in a host, and want consistent hashing among all of them, ie
if they all use the boot time generated rss key, or if some application
is choosing specific tuple(s) so that incoming traffic lands into known
rx queue(s).
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Wed, 23 Sep 2015 00:01:11 +0000 (17:01 -0700)]
net: revert "net_sched: move tp->root allocation into fw_init()"
fw filter uses tp->root==NULL to check if it is the old method,
so it doesn't need allocation at all in this case. This patch
reverts the offending commit and adds some comments for old
method to make it obvious.
Fixes: 33f8b9ecdb15 ("net_sched: move tp->root allocation into fw_init()") Reported-by: Akshat Kakkar <akshat.1984@gmail.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / people / julieng / linux-arm.git / log