This adds support for multiple namespaces by introducing a new 'nvme-ns'
device model. The nvme device creates a bus named from the device name
('id'). The nvme-ns devices then connect to this and registers
themselves with the nvme device.
This changes how an nvme device is created. Example with two namespaces:
Currently, the device only issues a single block backend request per
NVMe request, but as we move towards supporting metadata (and
discontiguous vector requests supported by OpenChannel 2.0) it will be
required to issue multiple block backend requests per NVMe request.
With this patch the NVMe device is ready for that.
Signed-off-by: Klaus Birkelund Jensen <klaus.jensen@cnexlabs.com>
Instead of handling both QSGs and IOVs in multiple places, simply use
QSGs everywhere by assuming that the request does not involve the
controller memory buffer (CMB). If the request is found to involve the
CMB, convert the QSG to an IOV and issue the I/O. The QSG is converted
to an IOV by the dma helpers anyway, so the CMB path is not unfairly
affected by this simplifying change.
As a side-effect, this patch also allows PRPs to be located in the CMB.
The logic ensures that if some of the PRP is in the CMB, all of it must
be located there.
Signed-off-by: Klaus Birkelund Jensen <klaus.jensen@cnexlabs.com>
Add the new Namespace Identification Descriptor List (CNS 03h) and track
creation of queues to enable the controller to return Command Sequence
Error if Set Features is called for Number of Queues after any queues
have been created.
Signed-off-by: Klaus Birkelund Jensen <klaus.jensen@cnexlabs.com>
Add support for the Get Log Page command and stub/dumb implementations
of the mandatory Error Information, SMART/Health Information and
Firmware Slot Information log pages.
Required for compliance with NVMe revision 1.2.1. See NVM Express 1.2.1,
Section 5.10 ("Get Log Page command").
Signed-off-by: Klaus Birkelund Jensen <klaus.jensen@cnexlabs.com>
nvme: populate the mandatory subnqn and ver fields
Required for compliance with NVMe revision 1.2.1 or later. See NVM
Express 1.2.1, Section 5.11 ("Identify command"), Figure 90 and Section
7.9 ("NVMe Qualified Names").
This also bumps the supported version to 1.2.1.
Signed-off-by: Klaus Birkelund Jensen <klaus.jensen@cnexlabs.com>
The Log Page Attributes in the Identify Controller structure indicates
that the controller supports the SMART / Health Information log page on
a per namespace basis. It does not, given that neither this log page or
the Get Log Page command is implemented.
Signed-off-by: Klaus Birkelund Jensen <klaus.jensen@cnexlabs.com>
The device model currently only supports a single namespace and also
specifically sets num_namespaces to 1. Take this into account and
simplify the code.
Signed-off-by: Klaus Birkelund Jensen <klaus.jensen@cnexlabs.com>
Peter Maydell [Mon, 23 Sep 2019 09:56:46 +0000 (10:56 +0100)]
Merge remote-tracking branch 'remotes/cminyard/tags/ipmi-for-release-2019-09-20' into staging
ipmi: Some bug fixes and new interfaces
Some bug fixes for the watchdog and hopeful the BT tests.
Change the IPMI UUID handling to give the user the ability to set it or
not have it.
Add a PCI interface.
Add an SMBus interfaces.
-corey
# gpg: Signature made Fri 20 Sep 2019 20:11:21 BST
# gpg: using RSA key FD0D5CE67CE0F59A6688268661F38C90919BFF81
# gpg: Good signature from "Corey Minyard <cminyard@mvista.com>" [unknown]
# gpg: aka "Corey Minyard <minyard@acm.org>" [unknown]
# gpg: aka "Corey Minyard <corey@minyard.net>" [unknown]
# gpg: aka "Corey Minyard <minyard@mvista.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FD0D 5CE6 7CE0 F59A 6688 2686 61F3 8C90 919B FF81
* remotes/cminyard/tags/ipmi-for-release-2019-09-20:
pc: Add an SMB0 ACPI device to q35
ipmi: Fix SSIF ACPI handling to use the right CRS
acpi: Add i2c serial bus CRS handling
ipmi: Add an SMBus IPMI interface
ipmi: Add PCI IPMI interfaces
smbios:ipmi: Ignore IPMI devices with no fwinfo function
ipmi: Allow a size value to be passed for I/O space
ipmi: Split out BT-specific code from ISA BT code
ipmi: Split out KCS-specific code from ISA KCS code
ipmi: Add a UUID device property
qdev: Add a no default uuid property
tests:ipmi: Fix IPMI BT tests
ipmi: Generate an interrupt on watchdog pretimeout expiry
ipmi: Fix the get watchdog command
ipmi: Fix watchdog NMI handling
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Corey Minyard [Fri, 13 May 2016 01:43:45 +0000 (20:43 -0500)]
pc: Add an SMB0 ACPI device to q35
This is so I2C devices can be found in the ACPI namespace. Currently
that's only IPMI, but devices can be easily added now.
Adding the devices required some PCI information, and the bus itself
to be added to the PCMachineState structure.
Note that this only works on Q35, the ACPI for PIIX4 is not capable
of handling an SMBus device.
Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Igor Mammedov <imammedo@redhat.com> Signed-off-by: Corey Minyard <cminyard@mvista.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Using the UUID that qemu generates probably isn't the best thing
to do, allow it to be passed in via properties, and use QemuUUID
for the type.
If the UUID is not set, return an unsupported command error. This
way we are not providing an all-zero (or randomly generated) GUID
to the IPMI user. This lets the host fall back to the other
method of using the get device id command to determind the BMC
being accessed.
Signed-off-by: Corey Minyard <cminyard@mvista.com> Cc: Cédric Le Goater <clg@kaod.org> Cc: David Gibson <david@gibson.dropbear.id.au> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com>
Corey Minyard [Thu, 27 Jun 2019 22:42:25 +0000 (17:42 -0500)]
tests:ipmi: Fix IPMI BT tests
The IPMI BT tests had a race condition, if it receive an IPMI command
to enable interrupt, it would write the message to enable interrupts
after it wrote the command response. So the test code could
receive the command response and issue the next command before the
device handled the interrupt enable command, and thus no interrupt.
So send the message to enable interrupt before the command response.
Also add some sleeps to give qemu time to handle responses, there was
no delay before, and it could result in an invalid timeout.
And re-enable the tests, as hopefully they are fixed now.
Note that I was unable to reproduce this even with the instructions
Peter gave me, but hopefully this fixes the issue.
Cc: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Corey Minyard <cminyard@mvista.com>
Corey Minyard [Fri, 16 Aug 2019 14:09:21 +0000 (09:09 -0500)]
ipmi: Fix watchdog NMI handling
The wrong logic was used for detection (so it wouldn't work at all)
and the wrong interface was used to inject the NMI if the detection
logic was correct.
Signed-off-by: Corey Minyard <cminyard@mvista.com> Reviewed-by: Cédric Le Goater <clg@kaod.org>
Peter Maydell [Fri, 20 Sep 2019 16:28:42 +0000 (17:28 +0100)]
Merge remote-tracking branch 'remotes/cleber/tags/python-next-pull-request' into staging
Python (acceptance tests) queue, 2019-09-19
# gpg: Signature made Thu 19 Sep 2019 17:24:04 BST
# gpg: using RSA key 7ABB96EB8B46B94D5E0FE9BB657E8D33A5F209F3
# gpg: Good signature from "Cleber Rosa <crosa@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 7ABB 96EB 8B46 B94D 5E0F E9BB 657E 8D33 A5F2 09F3
* remotes/cleber/tags/python-next-pull-request:
BootLinuxSshTest: Only run the tests when explicitly requested
tests/acceptance: Specify arch for QueryCPUModelExpansion
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell [Thu, 19 Sep 2019 15:59:57 +0000 (16:59 +0100)]
Makefile: Fix in-tree builds when Sphinx is available
In commit 27a296fce9821e we switched the qemu-ga manpage over to
being built from Sphinx. The makefile rules for this were correct
for an out-of-tree build, but break for in-tree builds if Sphinx is
present and we're trying to build the documentation.
Specifically, because Sphinx refuses to build output files into
the same directory as its sources, for an in-tree build we tell
it to build into a subdirectory docs/built, and set up a makefile
variable MANUAL_BUILDDIR indicating where the docs are going.
The makefile rule telling Make how to build qemu-ga.8 correctly
used this variable, but the lines adding qemu-ga.8 to the list
of DOCS to be built and the 'make install' rune did not. The
effect was that for an in-tree build we told Make to build
'docs/interop/qemu-ga.8' but did not provide a specific rule for
doing so, which caused Make to fall back to the old rules.make
rule for building any "%.8" file. Make tried to invoke texi2pod
with a bogus command line, resulting in the error:
GEN docs/interop/qemu-ga.8
No filename or title
make: *** [rules.mak:394: docs/interop/qemu-ga.8]
Fix this by using $(MANUAL_BUILDDIR) when constructing the
list of DOCS files we want to build and also in the source
file name we install for 'make install'.
(Among other things, this broke the Shippable CI builds.)
Fixes: 27a296fce9821e Reported-by: Eric Blake <eblake@redhat.com> Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190919155957.12618-1-peter.maydell@linaro.org Tested-by: Eric Blake <eblake@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com>
BootLinuxSshTest: Only run the tests when explicitly requested
Currently the Avocado framework does not distinct the time spent
downloading assets vs. the time spent running a test. With big
assets (like a full VM image) the tests likely fail.
This is a limitation known by the Avocado team.
Until this issue get fixed, do not run this tests automatically.
Tests can still be run setting the AVOCADO_TIMEOUT_EXPECTED
environment variable.
Reported-by: Gerd Hoffmann <kraxel@redhat.com> Reported-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com> Reviewed-by: Cleber Rosa <crosa@redhat.com>
Message-Id: <20190918122748.2144-1-philmd@redhat.com> Signed-off-by: Cleber Rosa <crosa@redhat.com>
Justin Hibbits [Wed, 21 Aug 2019 08:25:46 +0000 (10:25 +0200)]
Fix cacheline detection on FreeBSD/powerpc.
machdep.cacheline_size is an integer, not a long. Since PowerPC is
big-endian this causes sysctlbyname() to fill in the upper bits of the
argument, rather than the correct 'lower bits' of the word. Specify the
correct type to fix this.
* remotes/stefanha/tags/tracing-pull-request:
trace: Forbid event format ending with newline character
trace: Remove trailing newline in events
loader: Trace loaded images
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell [Thu, 19 Sep 2019 10:14:28 +0000 (11:14 +0100)]
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-4.2-sf1-v3' into staging
RISC-V Patches for the 4.2 Soft Freeze, Part 1, v3
This contains quite a few patches that I'd like to target for 4.2.
They're mostly emulation fixes for the sifive_u board, which now much
more closely matches the hardware and can therefor run the same fireware
as what gets loaded onto the board. Additional user-visible
improvements include:
* support for loading initrd files from the command line into Linux, via
/chosen/linux,initrd-{start,end} device tree nodes.
* The conversion of LOG_TRACE to trace events.
* The addition of clock DT nodes for our uart and ethernet.
This also includes some preliminary work for the H extension patches,
but does not include the H extension patches as I haven't had time to
review them yet.
This passes my OE boot test on 32-bit and 64-bit virt machines, as well
as a 64-bit upstream Linux boot on the sifive_u machine. It has been
fixed to actually pass "make check" this time.
Changes since v2 (never made it to the list):
* Sets the sifive_u machine default core count to 2 instead of 5.
Changes since v1 <20190910190513.21160-1-palmer@sifive.com>:
* Sets the sifive_u machine default core count to 5 instead of 1, as
it's impossible to have a single core sifive_u machine.
# gpg: Signature made Tue 17 Sep 2019 16:43:30 BST
# gpg: using RSA key 00CE76D1834960DFCE886DF8EF4CA1502CCBAB41
# gpg: issuer "palmer@dabbelt.com"
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
* remotes/palmer/tags/riscv-for-master-4.2-sf1-v3: (48 commits)
gdbstub: riscv: fix the fflags registers
target/riscv: Use TB_FLAGS_MSTATUS_FS for floating point
target/riscv: Fix mstatus dirty mask
target/riscv: Use both register name and ABI name
riscv: sifive_u: Update model and compatible strings in device tree
riscv: sifive_u: Remove handcrafted clock nodes for UART and ethernet
riscv: sifive_u: Fix broken GEM support
riscv: sifive_u: Instantiate OTP memory with a serial number
riscv: sifive: Implement a model for SiFive FU540 OTP
riscv: roms: Update default bios for sifive_u machine
riscv: sifive_u: Change UART node name in device tree
riscv: sifive_u: Update UART base addresses and IRQs
riscv: sifive_u: Reference PRCI clocks in UART and ethernet nodes
riscv: sifive_u: Add PRCI block to the SoC
riscv: sifive_u: Generate hfclk and rtcclk nodes
riscv: sifive: Implement PRCI model for FU540
riscv: sifive_u: Update PLIC hart topology configuration string
riscv: sifive_u: Update hart configuration to reflect the real FU540 SoC
riscv: sifive_u: Set the minimum number of cpus to 2
riscv: hart: Add a "hartid-base" property to RISC-V hart array
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
KONRAD Frederic [Thu, 12 Sep 2019 14:02:00 +0000 (16:02 +0200)]
target/m68k/fpu_helper.c: rename the access arguments
The "access" arguments clash with a macro under Windows with MinGW:
CC m68k-softmmu/target/m68k/fpu_helper.o
target/m68k/fpu_helper.c: In function 'fmovem_predec':
target/m68k/fpu_helper.c:405:56: error: macro "access" passed 4 arguments,
but takes just 2
size = access(env, addr, &env->fregs[i], ra);
So this renames them access_fn.
Tested with:
./configure --target-list=m68k-softmmu
make -j8
Signed-off-by: KONRAD Frederic <frederic.konrad@adacore.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com> Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <1568296920-29939-1-git-send-email-frederic.konrad@adacore.com> Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Thomas Huth [Wed, 4 Sep 2019 05:27:39 +0000 (07:27 +0200)]
Replace '-machine accel=xyz' with '-accel xyz'
We've got a separate option to configure the accelerator nowadays, which
is shorter to type and the preferred way of specifying an accelerator.
Use it in the source and examples to show that it is the favored option.
(However, do not touch the places yet which also specify other machine
options or multiple accelerators - these are currently still better
handled with one single "-machine" statement instead)
Signed-off-by: Thomas Huth <thuth@redhat.com> Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20190904052739.22123-1-thuth@redhat.com> Signed-off-by: Laurent Vivier <laurent@vivier.eu>
cutils: Move size_to_str() from "qemu-common.h" to "qemu/cutils.h"
"qemu/cutils.h" contains various qemu_strtosz_*() functions
useful to convert strings to size. It seems natural to have
the opposite usage (from size to string) there too.
The function definition is already in util/cutils.c.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com> Reviewed-by: John Snow <jsnow@redhat.com> Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190903120555.7551-1-philmd@redhat.com> Signed-off-by: Laurent Vivier <laurent@vivier.eu>
David Gibson [Wed, 18 Sep 2019 07:06:54 +0000 (17:06 +1000)]
tests/acceptance: Specify arch for QueryCPUModelExpansion
At the moment this test runs on whatever the host arch is. But it looks
for 'unavailable-features' which is an x86 specific cpu property. Tag it
to always use qemu-system-x86_64.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com> Reviewed-by: Cleber Rosa <crosa@redhat.com>
Message-Id: <20190918070654.19356-1-david@gibson.dropbear.id.au> Signed-off-by: Cleber Rosa <crosa@redhat.com>
trace: Forbid event format ending with newline character
Event format ending with newlines confuse the trace reports.
Forbid them.
Add a check to refuse new format added with trailing newline:
$ make
[...]
GEN hw/misc/trace.h
Traceback (most recent call last):
File "scripts/tracetool.py", line 152, in <module>
main(sys.argv)
File "scripts/tracetool.py", line 143, in main
events.extend(tracetool.read_events(fh, arg))
File "scripts/tracetool/__init__.py", line 367, in read_events
event = Event.build(line)
File "scripts/tracetool/__init__.py", line 281, in build
raise ValueError("Event format can not end with a newline character")
ValueError: Error at hw/misc/trace-events:121: Event format can not end with a newline character
Reviewed-by: John Snow <jsnow@redhat.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190916095121.29506-3-philmd@redhat.com
Message-Id: <20190916095121.29506-3-philmd@redhat.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
While the tracing framework does not forbid trailing newline in
events format string, using them lead to confuse output.
It is the responsibility of the backend to properly end an event
line.
Some of our formats have trailing newlines, remove them.
[Fixed typo in commit description reported by Eric Blake
<eblake@redhat.com>
--Stefan]
Reviewed-by: John Snow <jsnow@redhat.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190916095121.29506-2-philmd@redhat.com
Message-Id: <20190916095121.29506-2-philmd@redhat.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
KONRAD Frederic [Tue, 10 Sep 2019 08:15:41 +0000 (10:15 +0200)]
gdbstub: riscv: fix the fflags registers
While debugging an application with GDB the following might happen:
(gdb) return
Make xxx return now? (y or n) y
Could not fetch register "fflags"; remote failure reply 'E14'
This is because riscv_gdb_get_fpu calls riscv_csrrw_debug with a wrong csr
number (8). It should use the csr_register_map in order to reach the
riscv_cpu_get_fflags callback.
Bin Meng [Fri, 6 Sep 2019 16:20:18 +0000 (09:20 -0700)]
riscv: sifive_u: Remove handcrafted clock nodes for UART and ethernet
In the past we did not have a model for PRCI, hence two handcrafted
clock nodes ("/soc/ethclk" and "/soc/uartclk") were created for the
purpose of supplying hard-coded clock frequencies. But now since we
have added the PRCI support in QEMU, we don't need them any more.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Bin Meng [Fri, 6 Sep 2019 16:20:17 +0000 (09:20 -0700)]
riscv: sifive_u: Fix broken GEM support
At present the GEM support in sifive_u machine is seriously broken.
The GEM block register base was set to a weird number (0x100900FC),
which for no way could work with the cadence_gem model in QEMU.
Not like other GEM variants, the FU540-specific GEM has a management
block to control 10/100/1000Mbps link speed changes, that is mapped
to 0x100a0000. We can simply map it into MMIO space without special
handling using create_unimplemented_device().
Update the GEM node compatible string to use the official name used
by the upstream Linux kernel, and add the management block reg base
& size to the <reg> property encoding.
Tested with upstream U-Boot and Linux kernel MACB drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Bin Meng [Fri, 6 Sep 2019 16:20:16 +0000 (09:20 -0700)]
riscv: sifive_u: Instantiate OTP memory with a serial number
This adds an OTP memory with a given serial number to the sifive_u
machine. With such support, the upstream U-Boot for sifive_fu540
boots out of the box on the sifive_u machine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Bin Meng [Fri, 6 Sep 2019 16:20:15 +0000 (09:20 -0700)]
riscv: sifive: Implement a model for SiFive FU540 OTP
This implements a simple model for SiFive FU540 OTP (One-Time
Programmable) Memory interface, primarily for reading out the
stored serial number from the first 1 KiB of the 16 KiB OTP
memory reserved by SiFive for internal use.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Bin Meng [Fri, 6 Sep 2019 16:20:14 +0000 (09:20 -0700)]
riscv: roms: Update default bios for sifive_u machine
With the support of heterogeneous harts and PRCI model, it's now
possible to use the OpenSBI image (PLATFORM=sifive/fu540) built
for the real hardware.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Bin Meng [Fri, 6 Sep 2019 16:20:13 +0000 (09:20 -0700)]
riscv: sifive_u: Change UART node name in device tree
OpenSBI for fu540 does DT fix up (see fu540_modify_dt()) by updating
chosen "stdout-path" to point to "/soc/serial@...", and U-Boot will
use this information to locate the serial node and probe its driver.
However currently we generate the UART node name as "/soc/uart@...",
causing U-Boot fail to find the serial node in DT.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Bin Meng [Fri, 6 Sep 2019 16:20:11 +0000 (09:20 -0700)]
riscv: sifive_u: Reference PRCI clocks in UART and ethernet nodes
Now that we have added a PRCI node, update existing UART and ethernet
nodes to reference PRCI as their clock sources, to keep in sync with
the Linux kernel device tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Bin Meng [Fri, 6 Sep 2019 16:20:06 +0000 (09:20 -0700)]
riscv: sifive_u: Update hart configuration to reflect the real FU540 SoC
The FU540-C000 includes a 64-bit E51 RISC-V core and four 64-bit U54
RISC-V cores. Currently the sifive_u machine only populates 4 U54
cores. Update the max cpu number to 5 to reflect the real hardware,
by creating 2 CPU clusters as containers for RISC-V hart arrays to
populate heterogeneous harts.
The cpu nodes in the generated DTS have been updated as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Bin Meng [Fri, 6 Sep 2019 16:20:04 +0000 (09:20 -0700)]
riscv: hart: Add a "hartid-base" property to RISC-V hart array
At present each hart's hartid in a RISC-V hart array is assigned
the same value of its index in the hart array. But for a system
that has multiple hart arrays, this is not the case any more.
Add a new "hartid-base" property so that hartid number can be
assigned based on the property value.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Bin Meng [Fri, 6 Sep 2019 16:20:03 +0000 (09:20 -0700)]
riscv: hart: Extract hart realize to a separate routine
Currently riscv_harts_realize() creates all harts based on the
same cpu type given in the hart array property. With current
implementation it can only create homogeneous harts. Exact the
hart realize to a separate routine in preparation for supporting
multiple hart arrays.
Note the file header says the RISC-V hart array holds the state
of a heterogeneous array of RISC-V harts, which is not true.
Update the comment to mention homogeneous array of RISC-V harts.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Bin Meng [Fri, 6 Sep 2019 16:19:48 +0000 (09:19 -0700)]
riscv: hw: Remove duplicated "hw/hw.h" inclusion
Commit a27bd6c779ba ("Include hw/qdev-properties.h less") wrongly
added "hw/hw.h" to sifive_prci.c and sifive_test.c.
Another inclusion of "hw/hw.h" was later added via
commit 650d103d3ea9 ("Include hw/hw.h exactly where needed"), that
resulted in duplicated inclusion of "hw/hw.h".
Fixes: a27bd6c779ba ("Include hw/qdev-properties.h less") Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Bin Meng [Wed, 14 Aug 2019 15:33:32 +0000 (08:33 -0700)]
riscv: hmp: Add a command to show virtual memory mappings
This adds 'info mem' command for RISC-V, to show virtual memory
mappings that aids debugging.
Rather than showing every valid PTE, the command compacts the
output by merging all contiguous physical address mappings into
one block and only shows the merged block mapping details.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com> Reviewed-by: Palmer Dabbelt <palmer@sifive.com> Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Bin Meng [Fri, 16 Aug 2019 13:09:36 +0000 (06:09 -0700)]
riscv: Resolve full path of the given bios image
At present when "-bios image" is supplied, we just use the straight
path without searching for the configured data directories. Like
"-bios default", we add the same logic so that "-L" actually works.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Bin Meng [Thu, 8 Aug 2019 02:49:30 +0000 (19:49 -0700)]
riscv: rv32: Root page table address can be larger than 32-bit
For RV32, the root page table's PPN has 22 bits hence its address
bits could be larger than the maximum bits that target_ulong is
able to represent. Use hwaddr instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Alistair Francis [Tue, 30 Jul 2019 23:35:24 +0000 (16:35 -0700)]
target/riscv: Create function to test if FP is enabled
Let's create a function that tests if floating point support is
enabled. We can then protect all floating point operations based on if
they are enabled.
This patch so far doesn't change anything, it's just preparing for the
Hypervisor support for floating point operations.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com> Reviewed-by: Christophe de Dinechin <dinechin@redhat.com> Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
projects / people / pauldu / qemu.git / log