According to Amlogic datasheets for the SoCs supported by this driver, the
maximum bit clock rate is 100MHz.
The tdm interface allows the rates listed by the DAI driver, regardless of
the number slots or their width. However, these will impact the bit clock
rate.
Hitting the 100MHz limit is very unlikely for most use cases but it is
possible.
For example with 32 slots / 32 bits wide, the maximum rate is no longer
384kHz but ~96kHz.
Add the constraint accordingly if the component is not already active.
If it is active, the rate is already constrained by the first stream rate.
By default, when mclk-fs is not provided, the tdm-interface driver
requests an MCLK that is 4x the bit clock, SCLK.
However there is no justification for this:
* If the codec needs MCLK for its operation, mclk-fs is expected to be set
according to the codec requirements.
* If the codec does not need MCLK the minimum is 2 * SCLK, because this is
minimum the divider between SCLK and MCLK can do.
Multiplying by 4 may cause problems because the PLL limit may be reached
sooner than it should, so use 2x instead.
mtd-ram can potentially be larger than 4GB. get_bitmask_order() uses
fls() that is not guaranteed to work with values larger than 32-bit.
Specifically on aarch64 fls() returns 0 when all 32 LSB bits are clear.
Use fls64() instead.
A sync lost issue can be observed with two displays, when moving a plane
from one disabled display to an another disabled display, and then
enabling the display to which the plane was moved to. The exact
requirements for this to trigger are not clear.
It looks like the issue is that the layers are left enabled in the first
display's OVR registers. Even if the corresponding VP is disabled, it
still causes an issue, as if the disabled VP and its OVR would still be
in use, leading to the same VID being used by two OVRs. However, this is
just speculation based on testing the DSS behavior.
Experimentation shows that as a workaround, we can disable all the
layers in the OVR when disabling a VP. There should be no downside to
this, as the OVR is anyway effectively disabled if its VP is disabled,
and it seems to solve the sync lost issue.
However, there may be a bigger issue in play here, related to J721e
erratum i2097 ("DSS: Disabling a Layer Connected to Overlay May Result
in Synclost During the Next Frame"). Experimentation also shows that the
OVR's CHANNELIN field has similar issue. So we may need to revisit this
when we find out more about the core issue.
When the driver sets up the zpos property it sets the default zpos value
to the HW id of the plane. That is fine as such, but as on many DSS
versions the driver arranges the DRM planes in a different order than
the HW planes (to keep the non-scalable planes first), this leads to odd
initial zpos values. An example is J721e, where the initial zpos values
for DRM planes are 1, 3, 0, 2.
In theory the userspace should configure the zpos values properly when
using multiple planes, and in that sense the initial zpos values
shouldn't matter, but there's really no reason not to fix this and help
the userspace apps which don't handle zpos perfectly. In particular,
some versions of Weston seem to have issues dealing with the planes
with the current default zpos values.
So let's change the zpos values for the DRM planes to 0, 1, 2, 3.
Another option would be to configure the planes marked as primary planes
to zpos 0. On a two display system this would give us plane zpos values
of 0, 0, 1, 2. The end result and behavior would be very similar in this
option, and I'm not aware that this would actually help us in any way.
So, to keep the code simple, I opted for the 0, 1, 2, 3 values.
clang-16 warns about casting between incompatible function types:
arch/arm/crypto/sha256_glue.c:37:5: error: cast from 'void (*)(u32 *, const void *, unsigned int)' (aka 'void (*)(unsigned int *, const void *, unsigned int)') to 'sha256_block_fn *' (aka 'void (*)(struct sha256_state *, const unsigned char *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
37 | (sha256_block_fn *)sha256_block_data_order);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/arm/crypto/sha512-glue.c:34:3: error: cast from 'void (*)(u64 *, const u8 *, int)' (aka 'void (*)(unsigned long long *, const unsigned char *, int)') to 'sha512_block_fn *' (aka 'void (*)(struct sha512_state *, const unsigned char *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
34 | (sha512_block_fn *)sha512_block_data_order);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix the prototypes for the assembler functions to match the typedef.
The code already relies on the digest being the first part of the
state structure, so there is no change in behavior.
Fixes: c80ae7ca3726 ("crypto: arm/sha512 - accelerated SHA-512 using ARM generic ASM and NEON") Fixes: b59e2ae3690c ("crypto: arm/sha256 - move SHA-224/256 ASM/NEON implementation to base layer") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_parse_phandle() returns a device_node with refcount incremented, which
the callee needs to call of_node_put() on when done. We should only call
of_node_put() when the property argument is provided though as otherwise
nothing has taken a reference on the node.
Fixes: f36e789a1f8d ("mfd: altera-sysmgr: Add SOCFPGA System Manager") Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Link: https://lore.kernel.org/r/20240220115012.471689-4-peter.griffin@linaro.org Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_parse_phandle() returns a device_node with refcount incremented, which
the callee needs to call of_node_put() on when done. We should only call
of_node_put() when the property argument is provided though as otherwise
nothing has taken a reference on the node.
Fixes: 45330bb43421 ("mfd: syscon: Allow property as NULL in syscon_regmap_lookup_by_phandle") Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Link: https://lore.kernel.org/r/20240220115012.471689-2-peter.griffin@linaro.org Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Inside tegra_fb_create(), drm_gem_object_lookup() increments ref count of
the found object. But if the following size check fails then the last
found object's ref count should be put there as the unreferencing loop
can't detect this situation.
Found by Linux Verification Center (linuxtesting.org).
Per PCIe r6.1, sec 2.2.6.2 and 7.5.3.4, a Requester may not use 8-bit Tags
unless its Extended Tag Field Enable is set, but all Receivers/Completers
must handle 8-bit Tags correctly regardless of their Extended Tag Field
Enable.
Some devices do not handle 8-bit Tags as Completers, so add a quirk for
them. If we find such a device, we disable Extended Tags for the entire
hierarchy to make peer-to-peer DMA possible.
The 3ware 9650SE seems to have issues with handling 8-bit tags. Mark it as
broken.
The register bits definitions for RGB666 formats are wrong in multiple
ways: first, in the DSI_PS_SEL bits region, the Packed 18-bits RGB666
format is selected with bit 1, while the Loosely Packed one is bit 2,
and second - the definition name "LOOSELY_PS_18BIT_RGB666" is wrong
because the loosely packed format is 24 bits instead!
Either way, functions mtk_dsi_ps_control_vact() and mtk_dsi_ps_control()
do not even agree on the DSI_PS_SEL bit to set in DSI_PSCTRL: one sets
loosely packed (24) on RGB666, the other sets packed (18), and the other
way around for RGB666_PACKED.
Fixing this entire stack of issues is done in one go:
- Use the correct bit for the Loosely Packed RGB666 definition
- Rename LOOSELY_PS_18BIT_RGB666 to LOOSELY_PS_24BIT_RGB666
- Change ps_bpp_mode in mtk_dsi_ps_control_vact() to set:
- Loosely Packed, 24-bits for MIPI_DSI_FMT_RGB666
- Packed, 18-bits for MIPI_DSI_FMT_RGB666_PACKED
Currently coefficients are applied only once, since they don't change.
However, this is done before enable bit is set and thus it doesn't get
applied properly.
Fix that by applying coefficients after enable bit is set. While this
means that it will be done evey time, it doesn't bring much time
penalty.
bit_size field holds size of slice, not slice + header. Because of HW
quirks, driver can't program in just slice, but also preceding header.
But that means that currently used bit_size is wrong (too small).
Instead, just use size of whole buffer. There is no harm in doing this.
Currently mv col aux buffers are allocated as a pool. This is not
optimal because pool size equals number of buffers before stream is
started. Buffers can easily be allocated afterwards. In such cases,
invalid pointer is assigned to the decoding frame and Cedrus might
overwrite memory location which is allocated to different task.
Solve this issue with allocating mv col buffer once capture buffer is
actually used.
If device_register() fails in ntb_register_device(), the device name
allocated by dev_set_name() should be freed. As per the comment in
device_register(), callers should use put_device() to give up the
reference in the error path. So fix this by calling put_device() in the
error path so that the name can be freed in kobject_cleanup().
As a result of this, put_device() in the error path of
ntb_register_device() is removed and the actual error is returned.
As ntb_register_device() don't handle error of device_register(),
if ntb_register_device() returns error in pci_vntb_probe(), name of kobject
which is allocated in dev_set_name() called in device_add() is leaked.
As comment of device_add() says, it should call put_device() to drop the
reference count that was set in device_initialize()
when it fails, so the name can be freed in kobject_cleanup().
Signed-off-by: ruanjinjie <ruanjinjie@huawei.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
Stable-dep-of: aebfdfe39b93 ("NTB: fix possible name leak in ntb_register_device()") Signed-off-by: Sasha Levin <sashal@kernel.org>
Smatch complains about "head->full_size - head->header_size" can
underflow. To some extent, we're always going to have to trust the
firmware a bit. However, it's easy enough to add a check for negatives,
and let's add a upper bounds check as well.
Fixes: d2458baa799f ("ASoC: SOF: ipc3-loader: Implement firmware parsing and loading") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Link: https://msgid.link/r/5593d147-058c-4de3-a6f5-540ecb96f6f8@moroto.mountain Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move the firmware related information under a new struct (sof_firmware)
and add it to the high level snd_sof_dev struct.
Convert the generic code to use this new container when working with the
basefw and for compatibility reasons set the old plat_data members used by
the platforms.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Chao Song <chao.song@intel.com> Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Link: https://lore.kernel.org/r/20221020121238.18339-3-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 98f681b0f84c ("ASoC: SOF: Add some bounds checking to firmware data") Signed-off-by: Sasha Levin <sashal@kernel.org>
arch_vmap_pud_supported() and arch_vmap_pmd_supported() are
expected to constant-fold to false when RADIX is not enabled.
Force inlining in order to avoid following failure which
leads to unexpected call of non-existing pud_set_huge() and
pmd_set_huge() on powerpc 8xx.
In function 'pud_huge_tests',
inlined from 'debug_vm_pgtable' at mm/debug_vm_pgtable.c:1399:2:
./arch/powerpc/include/asm/vmalloc.h:9:33: warning: inlining failed in call to 'arch_vmap_pud_supported.isra': call is unlikely and code size would grow [-Winline]
9 | #define arch_vmap_pud_supported arch_vmap_pud_supported
| ^~~~~~~~~~~~~~~~~~~~~~~
./arch/powerpc/include/asm/vmalloc.h:10:20: note: in expansion of macro 'arch_vmap_pud_supported'
10 | static inline bool arch_vmap_pud_supported(pgprot_t prot)
| ^~~~~~~~~~~~~~~~~~~~~~~
./arch/powerpc/include/asm/vmalloc.h:9:33: note: called from here
9 | #define arch_vmap_pud_supported arch_vmap_pud_supported
mm/debug_vm_pgtable.c:458:14: note: in expansion of macro 'arch_vmap_pud_supported'
458 | if (!arch_vmap_pud_supported(args->page_prot) ||
| ^~~~~~~~~~~~~~~~~~~~~~~
clang-16 warns about casting functions to incompatible types, as is done
here to call clk_disable_unprepare:
sound/soc/meson/t9015.c:274:4: error: cast from 'void (*)(struct clk *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
274 | (void(*)(void *))clk_disable_unprepare,
The pattern of getting, enabling and setting a disable callback for a
clock can be replaced with devm_clk_get_enabled(), which also fixes
this warning.
clang-16 warns about casting functions to incompatible types, as is done
here to call clk_disable_unprepare:
sound/soc/meson/aiu.c:243:12: error: cast from 'void (*)(struct clk *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
243 | (void(*)(void *))clk_disable_unprepare,
The pattern of getting, enabling and setting a disable callback for a
clock can be replaced with devm_clk_get_enabled(), which also fixes
this warning.
Cycles is recognized as part of a hard coded metric in stat-shadow.c,
it may call print_metric_only with a NULL fmt string leading to a
segfault. Handle the NULL fmt explicitly.
Fixes: 088519f318be ("perf stat: Move the display functions to stat-display.c") Signed-off-by: Ian Rogers <irogers@google.com> Reviewed-by: Kan Liang <kan.liang@linux.intel.com> Cc: K Prateek Nayak <kprateek.nayak@amd.com> Cc: James Clark <james.clark@arm.com> Cc: Kaige Ye <ye@kaige.org> Cc: John Garry <john.g.garry@oracle.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20240209204947.3873294-4-irogers@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Add the module clock used by the Thermal Sensor/Chip Internal Voltage
Monitor/Core Voltage Monitor (THS/CIVM/CVM) on the Renesas R-Car V4H
(R8A779G0) SoC.
Based on a large patch in the BSP by Kazuya Mizuguchi.
When the topology calls for two interfaces on the current fixed topology
of 2 DSC blocks, or uses 1 DSC block for a single interface (e.g. SC7280
with only one DSC block), there should be no merging of DSC output.
This is already represented by the return value of
dpu_encoder_use_dsc_merge(), but not yet used to correctly configure
this flag.
Fixes: 58dca9810749 ("drm/msm/disp/dpu1: Add support for DSC in encoder") Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/577067/ Link: https://lore.kernel.org/r/20240204-dpu-dsc-multiplex-v1-1-080963233c52@somainline.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently INTF_CFG2_DATA_HCTL_EN is coupled with the enablement
of widebus but this is incorrect because we should be enabling
this bit independent of widebus except for cases where compression
is enabled in one pixel per clock mode.
Fix this by making the condition checks more explicit and enabling
INTF_CFG2_DATA_HCTL_EN for all other cases when supported by DPU.
The commit in Fixes changed the logic on how resources are released and
introduced a new switchtec_exit_pci() that need to be called explicitly in
order to undo a corresponding switchtec_init_pci().
This was done in the remove function, but not in the probe.
Dquot pointers in i_dquot array in the inode are protected by
dquot_srcu. Annotate the array pointers with __rcu, perform the locked
dereferences with srcu_dereference_check() instead of plain reads, and
set the array elements with rcu_assign_pointer().
Fixes: b9ba6f94b238 ("quota: remove dqptr_sem") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202402061900.rTuYDlo6-lkp@intel.com/ Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
If dquot_free_inode(or other routines) checks inode's quota pointers (1)
before quota_off sets it to NULL(2) and use it (3) after that, NULL pointer
dereference will be triggered.
So let's fix it by using a temporary pointer to avoid this issue.
Signed-off-by: Wang Jianjian <wangjianjian3@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20240202081852.2514092-1-wangjianjian3@huawei.com>
Stable-dep-of: 179b8c97ebf6 ("quota: Fix rcu annotations of inode dquot pointers") Signed-off-by: Sasha Levin <sashal@kernel.org>
As Honza said, remove_inode_dquot_ref() currently does not release the
last dquot reference but instead adds the dquot to tofree_head list. This
is because dqput() can sleep while dropping of the last dquot reference
(writing back the dquot and calling ->release_dquot()) and that must not
happen under dq_list_lock. Now that dqput() queues the final dquot cleanup
into a workqueue, remove_inode_dquot_ref() can call dqput() unconditionally
and we can significantly simplify it.
Here we open code the simplified code of remove_inode_dquot_ref() into
remove_dquot_ref() and remove the function put_dquot_list() which is no
longer used.
Signed-off-by: Baokun Li <libaokun1@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20230630110822.3881712-6-libaokun1@huawei.com>
Stable-dep-of: 179b8c97ebf6 ("quota: Fix rcu annotations of inode dquot pointers") Signed-off-by: Sasha Levin <sashal@kernel.org>
Trying to toggle the resets in a rapid fashion can lead to the changes
not actually arriving at the clock controller block when we expect them
to. This was observed at least on SM8250.
Read back the value after regmap_update_bits to ensure write completion.
The MT8192 does not support configuring pin slew rate. This is evident
from both the datasheet, and the fact that the driver points the slew
rate register range at the GPIO direction register range.
Drop the bogus setting.
Fixes: d32f38f2a8fc ("pinctrl: mediatek: Add pinctrl driver for mt8192") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20240131071910.3950450-2-wenst@chromium.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MT8186 does not support configuring pin slew rate. This is evident
from both the datasheet, and the fact that the driver points the slew
rate register range at the GPIO direction register range.
Drop the bogus setting.
Fixes: 8b483bda1e46 ("pinctrl: add pinctrl driver on mt8186") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20240131071910.3950450-1-wenst@chromium.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In dvb_register_device, *pdvbdev is set equal to dvbdev, which is freed
in several error-handling paths. However, *pdvbdev is not set to NULL
after dvbdev's deallocation, causing use-after-frees in many places,
for example, in the following call chain:
When calling dvb_unregister_device, dmxdev->dvbdev (i.e. *pdvbdev in
dvb_register_device) could point to memory that had been freed in
dvb_register_device. Thereafter, this pointer is transferred to
kref_put and triggering a use-after-free.
The entity->name (i.e. name) is allocated in v4l2_m2m_register_entity
but isn't freed in its following error-handling paths. This patch
adds such deallocation to prevent memleak of entity->name.
Fixes: be2fff656322 ("media: add helpers for memory-to-memory media controller") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
In tpg_alloc, resources should be deallocated in each and every
error-handling paths, since they are allocated in for statements.
Otherwise there would be memleaks because tpg_free is called only when
tpg_alloc return 0.
Fixes: 63881df94d3e ("[media] vivid: add the Test Pattern Generator") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Static analyzers generate alerts for an unchecked call to
`media_device_register()`. However, in this case, the device will work
reliably without the media controller API.
Add a comment above the call to prevent future unnecessary changes.
When SPI transfer is being prepared, the spi-s3c64xx driver will call
clk_set_rate() to change the rate of SPI source clock (IPCLK). But IPCLK
is a gate (leaf) clock, so it must propagate the rate change up the
clock tree, so that corresponding DIV clocks can actually change their
divider values. Add CLK_SET_RATE_PARENT flag to corresponding clocks for
all SPI instances in Exynos850 (spi_0, spi_1 and spi_2) to make it
possible. This change involves next clocks:
usi_spi_0:
Clock Block Div range
--------------------------------------------
gout_spi0_ipclk CMU_PERI -
dout_peri_spi0 CMU_PERI /1..32
mout_peri_spi_user CMU_PERI -
dout_peri_ip CMU_TOP /1..16
usi_cmgp0:
Clock Block Div range
--------------------------------------------
gout_cmgp_usi0_ipclk CMU_CMGP -
dout_cmgp_usi0 CMU_CMGP /1..32
mout_cmgp_usi0 CMU_CMGP -
gout_clkcmu_cmgp_bus CMU_APM -
dout_apm_bus CMU_APM /1..8
usi_cmgp1:
Clock Block Div range
--------------------------------------------
gout_cmgp_usi1_ipclk CMU_CMGP -
dout_cmgp_usi1 CMU_CMGP /1..32
mout_cmgp_usi1 CMU_CMGP -
gout_clkcmu_cmgp_bus CMU_APM -
dout_apm_bus CMU_APM /1..8
With input clock of 400 MHz, this scheme provides next IPCLK rate range,
for each SPI block:
Which should cover all possible applications of SPI bus. Of course,
setting SPI frequency to values as low as 500 kHz will also affect the
common bus dividers (dout_apm_bus or dout_peri_ip), which in turn
effectively lowers the rates for all leaf bus clocks derived from those
dividers, like HSI2C and I3C clocks. But at least it gives the board
designer a choice, whether to keep all clocks (SPI/HSI2C/I3C) at high
frequencies, or make all those clocks have lower frequencies. Not
propagating the rate change to those common dividers would limit this
choice to "only high frequencies are allowed for SPI/HSI2C/I3C" option,
making the common dividers useless. This decision follows the "Worse is
better" approach, relying on the users/engineers to know the system
internals when working with such low-level features, instead of trying
to account for all possible use-cases.
The 'stream' pointer is used in dcn10_set_output_transfer_func() before
the check if 'stream' is NULL.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn10/dcn10_hwseq.c:1892 dcn10_set_output_transfer_func() warn: variable dereferenced before check 'stream' (see line 1875)
Fixes: ddef02de0d71 ("drm/amd/display: add null checks before logging") Cc: Wyatt Wood <wyatt.wood@amd.com> Cc: Anthony Koo <Anthony.Koo@amd.com> Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Cc: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Tell snprintf() to store at most 10 bytes in the output buffer
instead of 30.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_debugfs.c:1508 dp_dsc_clock_en_read() error: snprintf() is printing too much 30 vs 10
Fixes: c06e09b76639 ("drm/amd/display: Add DSC parameters logging to debugfs") Cc: Alex Hung <alex.hung@amd.com> Cc: Qingqing Zhuo <qingqing.zhuo@amd.com> Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Cc: Aurabindo Pillai <aurabindo.pillai@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previous attempt to autodetect well-behaving patched firmware
introduced in commit 46a0a2c96f0f ("HID: lenovo: Detect quirk-free fw
on cptkbd and stop applying workaround") has shown that there are
false-positives on original firmware (on both 1st gen and 2nd gen
keyboards) which causes the middle button click workaround to be
mistakenly disabled.
This commit adds explicit parameter to sysfs to control this
workaround.
Fixes: 46a0a2c96f0f ("HID: lenovo: Detect quirk-free fw on cptkbd and stop applying workaround") Fixes: 43527a0094c1 ("HID: lenovo: Restrict detection of patched firmware only to USB cptkbd") Signed-off-by: Mikhail Khvainitski <me@khvoinitsky.org> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
perf_data__switch() may not assign a legal value to 'new_filename'.
In this case, 'new_filename' uses the on-stack value, which may cause a
incorrect free and unexpected result.
Fixes: 03724b2e9c45 ("perf record: Allow to limit number of reported perf.data files") Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20240119040304.3708522-2-yangjihong1@huawei.com Signed-off-by: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The TLP Prefix Log Register consists of multiple DWORDs (PCIe r6.1 sec
7.9.14.13) but the loop in dpc_process_rp_pio_error() keeps reading from
the first DWORD, so we print only the first PIO TLP Prefix (duplicated
several times), and we never print the second, third, etc., Prefixes.
Add the iteration count based offset calculation into the config read.
Update the architecture dependency to be the generic Tegra
because the driver works on the four latest Tegra generations
not just T210, if you build a kernel with a specific
ARCH_TEGRA_xxx_SOC option that excludes 210 you don't get
this driver.
Fixes: 433de642a76c9 ("dmaengine: tegra210-adma: add support for Tegra186/Tegra194") Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Thierry Reding <treding@nvidia.com> Cc: Sameer Pujar <spujar@nvidia.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20240112093310.329642-2-pbrobinson@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Handle potential acp_sofdsp_dai_links_create() errors in ACP SOF machine
driver's probe function. Note there is no need for an undo.
While at it, switch to dev_err_probe().
Fixes: 9f84940f5004 ("ASoC: amd: acp: Add SOF audio support on Chrome board") Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Reviewed-by: Emil Velikov <emil.velikov@collabora.com> Link: https://msgid.link/r/20231219030728.2431640-4-cristian.ciocaltea@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some edp panel requires T10 (Delay from end of valid video data transmitted
by the Source device to power-off) less than 500ms. Using autosuspend with
delay set as 1000 violates this requirement.
Use put_sync_suspend in unprepare to meet the spec. For other cases (such
as getting EDID), it still uses autosuspend.
Suggested-by: Douglas Anderson <dianders@chromium.org> Fixes: 3235b0f20a0a ("drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare") Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20231220221418.2610185-1-hsinyi@chromium.org Signed-off-by: Sasha Levin <sashal@kernel.org>
This scary message can misled the user into thinking something bad has
happened and needs to be fixed, however it could simply be part of a
normal boot process where EPROBE_DEFER is taken into account. Therefore,
let's use dev_err_probe so that this message doesn't get shown (by
default) when the return code is EPROBE_DEFER.
ret variable stores the return value of drm_of_find_panel_or_bridge
which can return error codes different from EPROBE_DEFER. Therefore,
let's just return that error code instead of forcing it to EPROBE_DEFER.
Unit testing this in VKMS shows that passing 0 into
this function returns -1, which is highly counter-
intuitive. Fix it by checking whether the input is
>= 0 instead of > 0.
Fixes: 64566b5e767f ("drm: Add drm_fixp_from_fraction and drm_fixp2int_ceil") Signed-off-by: Harry Wentland <harry.wentland@amd.com> Reviewed-by: Simon Ser <contact@emersion.fr> Reviewed-by: Melissa Wen <mwen@igalia.com> Signed-off-by: Melissa Wen <melissa.srw@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20231108163647.106853-2-harry.wentland@amd.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The controller wants the difference between *total and *sync_start in the
HDMI_VIDEO_EXT_*DELAY registers. Otherwise the signal is very unstable for
certain non-VIC modes. See downstream commit [0].
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Stable-dep-of: 830c1ded3563 ("drm/tegra: dsi: Fix some error handling paths in tegra_dsi_probe()") Signed-off-by: Sasha Levin <sashal@kernel.org>
The pm_runtime_enable function increases the power disable depth,
which means that we must perform a matching decrement on the error
handling path to maintain balance within the given context.
Additionally, we need to address the same issue for pm_runtime_get_sync.
We fix this by invoking pm_runtime_disable and pm_runtime_put_sync
when error returns.
There is this reported crash when experimenting with the lvm2 testsuite.
The list corruption is caused by the fact that the postsuspend and resume
methods were not paired correctly; there were two consecutive calls to the
origin_postsuspend function. The second call attempts to remove the
"hash_list" entry from a list, while it was already removed by the first
call.
Fix __dm_internal_resume so that it calls the preresume and resume
methods of the table's targets.
If a preresume method of some target fails, we are in a tricky situation.
We can't return an error because dm_internal_resume isn't supposed to
return errors. We can't return success, because then the "resume" and
"postsuspend" methods would not be paired correctly. So, we set the
DMF_SUSPENDED flag and we fake normal suspend - it may confuse userspace
tools, but it won't cause a kernel crash.
An empty flush doesn't have a payload, so it should never be looked at
when considering to possibly requeue a bio for the case when a reshape
is in progress.
Fixes: 9dbd1aa3a81c ("dm raid: add reshaping support to the target") Reported-by: Patrick Plenefisch <simonpatp@gmail.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On some architectures like ARM64, PMD_SIZE can be really large in some
configurations. Like with CONFIG_ARM64_64K_PAGES=y the PMD_SIZE is
512MB.
Use 2MB * num_possible_nodes() as the size for allocations done through
the prog pack allocator. On most architectures, PMD_SIZE will be equal
to 2MB in case of 4KB pages and will be greater than 2MB for bigger page
sizes.
The kmalloc_array() in nfp_fl_lag_do_work() will return null, if
the physical memory has run out. As a result, if we dereference
the acti_netdevs, the null pointer dereference bugs will happen.
This patch adds a check to judge whether allocation failure occurs.
If it happens, the delayed work will be rescheduled and try again.
Fixes: bb9a8d031140 ("nfp: flower: monitor and offload LAG groups") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Reviewed-by: Louis Peens <louis.peens@corigine.com> Link: https://lore.kernel.org/r/20240308142540.9674-1-duoming@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 3557baabf280 ("[L2TP]: PPP over L2TP driver core") Reviewed-by: Tom Parkin <tparkin@katalix.com> Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'olr' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'olr' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Reviewed-by: Jason Xing <kerneljasonxing@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the kernel isn't built with interconnect support, icc_get_name()
returns NULL and we get following warning:
drivers/opp/debugfs.c: In function 'bw_name_read':
drivers/opp/debugfs.c:43:42: error: '%.62s' directive argument is null [-Werror=format-overflow=]
i = scnprintf(buf, sizeof(buf), "%.62s\n", icc_get_name(path));
Fix it.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202402141313.81ltVF5g-lkp@intel.com/ Fixes: 0430b1d5704b0 ("opp: Expose bandwidth information via debugfs") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Reviewed-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The logic for enabling the TX clock shift is inverse of enabling the RX
clock shift. The TX clock shift is disabled when DP83822_TX_CLK_SHIFT is
set. Correct the current behavior and always write the delay configuration
to ensure consistent delay settings regardless of bootloader configuration.
Reference: https://www.ti.com/lit/ds/symlink/dp83822i.pdf p. 69
Fixes: 8095295292b5 ("net: phy: DP83822: Add setting the fixed internal delay") Signed-off-by: Tim Pambor <tp@osasysteme.de> Link: https://lore.kernel.org/r/20240305110608.104072-1-tp@osasysteme.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to Section 1.2 of Core Specification Supplement Part A the
complete or short name strings are defined as utf8s, which should not
include the trailing NULL for variable length array as defined in Core
Specification Vol1 Part E Section 2.9.3.
Removing the trailing NULL allows PTS to retrieve the random address based
on device name, e.g. for SM/PER/KDU/BV-02-C, SM/PER/KDU/BV-08-C or
GAP/BROB/BCST/BV-03-C.
Fixes: f61851f64b17 ("Bluetooth: Fix append max 11 bytes of name to scan rsp data") Signed-off-by: Frédéric Danis <frederic.danis@collabora.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There a few instances still using HCI_MAX_AD_LENGTH instead of using
max_adv_len which takes care of detecting what is the actual maximum
length depending on if the controller supports EA or not.
Fixes: 112b5090c219 ("Bluetooth: MGMT: Fix always using HCI_MAX_AD_LENGTH") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 2ab3e8d67fc1 ("Bluetooth: Fix eir name length") Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / people / aperard / linux.git / log