Avi Kivity [Mon, 15 Aug 2011 14:17:29 +0000 (17:17 +0300)]
sysbus: add a variant of sysbus_init_mmio_cb with an unmap callback
sysbus_init_mmio_cb() uses the destructive IO_MEM_UNASSIGNED to remove a
region. Provide an alternative that calls an unmap callback, so the removal
may be done non-destructively.
Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Brad [Sun, 14 Aug 2011 00:30:14 +0000 (20:30 -0400)]
Improvements to libtool support.
Improvements to the libtool support in QEMU. Replace hard coded
libtool in the infrastructure with $(LIBTOOL) and allow
overriding the libtool binary used via the configure
script.
Reviewed-by: Andreas F=E4rber <andreas.faerber@web.de> Signed-off-by: Brad Smith <brad@comstyle.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Bjørn Mork [Wed, 17 Aug 2011 09:03:14 +0000 (11:03 +0200)]
e1000: use MII status register for link up/down
Some guests will use the standard MII status register
to verify link state. They will not notice link changes
unless this register is updated.
Verified with Linux 3.0 and Windows XP guests.
Without this patch, ethtool will report speed and duplex as
unknown when the link is down, but still report the link as
up. This is because the Linux e1000 driver checks the
mac_reg[STATUS] register link state before it checks speed
and duplex, but uses the phy_reg[PHY_STATUS] register for
the actual link state check. Fix by updating both registers
on link state changes.
Linux guest before:
(qemu) set_link e1000.0 off
kvm-sid:~# ethtool eth0
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: Unknown!
Duplex: Unknown! (255)
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
MDI-X: Unknown
Supports Wake-on: umbg
Wake-on: d
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
(qemu) set_link e1000.0 on
Linux guest after:
(qemu) set_link e1000.0 off
[ 63.384221] e1000: eth0 NIC Link is Down
kvm-sid:~# ethtool eth0
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: Unknown!
Duplex: Unknown! (255)
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
MDI-X: Unknown
Supports Wake-on: umbg
Wake-on: d
Current message level: 0x00000007 (7)
drv probe link
Link detected: no
(qemu) set_link e1000.0 on
[ 84.304582] e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Michael Roth [Thu, 11 Aug 2011 20:38:12 +0000 (15:38 -0500)]
guest agent: remove uneeded dependencies
This patch tries to cull any uneeded library dependencies from the guest
agent to improve portability across various distros. We do so by being
as explicit as possible about in-tree dependencies rather than relying
on existing *-obj-y targets, and by manually setting LIBS for the
qemu-ga target to avoid pulling in LIBS_TOOLS libraries discovered by
configure.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Michael Roth [Thu, 11 Aug 2011 20:38:11 +0000 (15:38 -0500)]
guest agent: remove g_strcmp0 usage
g_strcmp0 isn't in all version of glib 2.0, so don't use it to avoid
build breakage on older distros.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com> Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Avi Kivity [Thu, 11 Aug 2011 07:40:26 +0000 (10:40 +0300)]
memory: crack wide ioport accesses into smaller ones when needed
The memory API supports cracking wide accesses into narrower ones
when needed; but this was no implemented for the pio address space,
causing lsi53c895a's IO BAR to malfunction.
Fix by correctly cracking wide accesses when needed.
Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Avi Kivity [Thu, 11 Aug 2011 07:40:25 +0000 (10:40 +0300)]
memory: abstract cracking of write access ops into a function
The memory API automatically cracks large reads and writes into smaller
ones when needed. Factor out this mechanism, which is now duplicated between
memory reads and memory writes, into a function.
Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
tcg: Always define all of the TCGOpcode enum members.
By always defining these symbols, we can eliminate a lot of ifdefs.
To allow this to be checked reliably, the semantics of the
TCG_TARGET_HAS_* macros must be changed from def/undef to true/false.
This allows even more ifdefs to be removed, converting them into
C if statements.
Signed-off-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Brad [Mon, 8 Aug 2011 00:02:11 +0000 (20:02 -0400)]
Check for presence of compiler -pthread flag.
OpenBSD / FreeBSD and some other OS's require the use of
cc -pthread to link threaded programs so have QEMU's
configure script check for the presence of the flag
and use it if so.
Signed-off-by: Brad Smith <brad@comstyle.com> Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Austin Clements [Mon, 15 Aug 2011 03:22:28 +0000 (23:22 -0400)]
monitor: Show combined protection bits in "info mem"
Previously, "info mem" considered and displayed only the last-level
protection bits for a memory range, which doesn't accurrately
represent the protection of that range. Now it shows the combined
protection.
Signed-off-by: Austin Clements <amdragon@mit.edu> Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Austin Clements [Mon, 15 Aug 2011 03:19:21 +0000 (23:19 -0400)]
monitor: Prevent sign-extension of 32-bit addresses printed by info mem
Previously, on 32-bit i386, info mem used signed 32-bit int's to store
the page table indexes. As a result, address calculation was done in
32 bits and then incorrectly sign-extended to 64 bits, yielding output
like
Stefan Weil [Fri, 15 Jul 2011 19:38:14 +0000 (21:38 +0200)]
w32: Fix format string regression
Commit 953ffe0f935f40c0d6061d69e76e0339393b54f8
introduced FMT_pid which is wrong for w32 and w64 getpid():
those getpid() implementations always return an int value.
Signed-off-by: Stefan Weil <weil@mail.berlios.de> Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Stefan Weil [Fri, 15 Jul 2011 19:38:13 +0000 (21:38 +0200)]
w64: Add definition of FMT_pid
For mingw-w64, pid_t is _pid_t which is __int64,
so this platform needs its own definition of FMT_pid.
Reviewed-by: Andreas Färber <andreas.faerber@web.de> Signed-off-by: Stefan Weil <weil@mail.berlios.de> Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Stefan Weil [Fri, 15 Jul 2011 19:38:12 +0000 (21:38 +0200)]
Fix conversions from pointer to tcg_target_long
tcg_gen_exit_tb takes a parameter of type tcg_target_long,
so the type casts of pointer to long should be replaced by
type casts of pointer to tcg_target_long.
These changes are needed for build environments where
sizeof(long) != sizeof(void *), especially for w64.
Cc: Alexander Graf <agraf@suse.de> Cc: Guan Xuetao <gxt@mprc.pku.edu.cn> Acked-by: Guan Xuetao<gxt@mprc.pku.edu.cn> Acked-by: Alexander Graf <agraf@suse.de> Signed-off-by: Stefan Weil <weil@mail.berlios.de> Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Peter Maydell [Fri, 19 Aug 2011 23:27:04 +0000 (00:27 +0100)]
target-cris/opcode-cris.h: rename REG_PC/SP to CRIS_REG_PC/SP
The REG_PC constant used in opcode-cris.h can clash with a
similar define in system include files. In particular the
Ubuntu Lucid SPARC signal.h will define REG_PC, and since
qemu-common.h now includes signal.h this was causing compile
failures. Rename the constants to avoid this issue.
(NB that REG_SP is not actually used within QEMU.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Engin AYDOGAN [Wed, 3 Aug 2011 21:15:23 +0000 (22:15 +0100)]
hw/stellaris: Add support for RCC2 register
Add support for the RCC2 register on Fury class devices.
Based on a patch by Vijay Kumar.
Signed-off-by: Engin AYDOGAN <engin@bzzzt.biz>
[Peter Maydell: fixed comment typos, minor cleanup of unreachable code] Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell [Wed, 3 Aug 2011 22:13:45 +0000 (23:13 +0100)]
hw/pl061: Convert to VMState
Convert the PL061 to VMState. We choose to widen the struct members
to uint32_t rather than the other two options of breaking migration
compatibility or using vmstate hacks to read/write a 32 bit value
into an 8 bit struct field.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell [Fri, 22 Jul 2011 15:36:54 +0000 (15:36 +0000)]
vexpress, realview: Use pl111, not pl110
The Versatile Express, Realview EB, PBX A9 and PB A8 boards all
use a PL111 for their graphics, not a PL110. Now we model the
PL111, use it on these board models.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell [Fri, 22 Jul 2011 13:42:39 +0000 (13:42 +0000)]
versatilepb: Implement SYS_CLCD mux control register bits
On the Versatile PB, PL110 graphics adaptor only natively supports
5551 pixel format; an external mux swaps bits around to allow
RGB565 and BGR565, under the control of bits [1:0] in the SYS_CLCD
system register.
Implement these SYS_CLCD register bits, and use a gpio line to
feed them out of the system register model, across the versatilepb
board and into the pl110 so we can select the right format.
This is necessary as recent Linux versatile kernels default to
programming the CLCD and mux for 16 bit BGR rather than 16 bit RGB.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell [Fri, 22 Jul 2011 13:19:33 +0000 (13:19 +0000)]
hw/pl110: Model the PL111 CLCD controller
Model the PL111 CLCD controller. This is a minor variation
on the PL110; the major programmer visible differences are
support for hardware cursor (unimplemented) and two new
pixel formats.
Since syborg_fb.c borrows the pl11x pixel drawing routines,
we also update it to cope with the new slightly larger array
of function pointers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Paolo Bonzini [Sun, 14 Aug 2011 21:05:49 +0000 (14:05 -0700)]
scsi: do not overwrite memory on REQUEST SENSE commands with a large buffer
Other scsi_target_reqops commands were careful about not using r->cmd.xfer
directly, and instead always cap it to a fixed length. This was not done
for REQUEST SENSE, and this patch fixes it.
Reported-by: Blue Swirl <blauwirbel@gmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Jan Kiszka [Sat, 6 Aug 2011 12:23:29 +0000 (14:23 +0200)]
slirp: Fix bit field types in IP header structs
-mms-bitfields prevents that the bitfields in current IP header structs
are packed into a single byte as it is required. Fix this by using
uint8_t as backing type.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Michael Roth [Wed, 10 Aug 2011 18:10:51 +0000 (13:10 -0500)]
qapi: fix build issue due to missing newline in generated header
Fixes a build issue on RHEL5, and potentially other distros, where gcc
will generate an error due to us not writing a trailing "\n" when
generating *qmp-commands.h
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Jiri Denemark [Wed, 10 Aug 2011 10:04:34 +0000 (12:04 +0200)]
build: Move QEMU_INCLUDES before QEMU_CFLAGS
This patch fixes build when any of the include paths from QEMU_CFLAGS
contains a header file with similar name to a header file in qemu
sources. I hit it with error.h included by qapi/qapi-types-core.h. GCC
decided to use /usr/include/alsa/error.h instead of qemu's error.h.
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com> Signed-off-by: Jiri Denemark <jdenemar@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Stefan Weil [Sat, 6 Aug 2011 20:47:22 +0000 (22:47 +0200)]
configure: Disable guest_agent for mingw32
guest_agent is not supported for mingw32, so the default value
should be 'no', not 'yes'.
This removes the dependencies to glib-2.0 and python which
makes native and cross builds for w32 much easier (no need
to get and install these extra packages).
It also avoids the problems caused by different bitfield alignment
which is required by glib-2.0.
It is still possible to set guest_agent=yes via configure option.
Signed-off-by: Stefan Weil <weil@mail.berlios.de> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Paolo Bonzini [Wed, 3 Aug 2011 08:49:17 +0000 (10:49 +0200)]
scsi: add support for unit attention conditions
Unit attention conditions override any sense data the device already
has. Their signaling and clearing is handled entirely by the SCSIBus
code, and they are completely transparent to the SCSIDevices.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>