`ni_cdio_cmdtest()` validates Comedi asynchronous commands for the DIO
subdevice (subdevice 2) of supported National Instruments M-series
cards. It is called when handling the `COMEDI_CMD` and `COMEDI_CMDTEST`
ioctls for this subdevice. There are two causes for a possible
divide-by-zero error when validating that the `stop_arg` member of the
passed-in command is not too large.
The first cause for the divide-by-zero is that calls to
`comedi_bytes_per_scan()` are only valid once the command has been
copied to `s->async->cmd`, but that copy is only done for the
`COMEDI_CMD` ioctl. For the `COMEDI_CMDTEST` ioctl, it will use
whatever was left there by the previous `COMEDI_CMD` ioctl, if any.
(This is very likely, as it is usual for the application to use
`COMEDI_CMDTEST` before `COMEDI_CMD`.) If there has been no previous,
valid `COMEDI_CMD` for this subdevice, then `comedi_bytes_per_scan()`
will return 0, so the subsequent division in `ni_cdio_cmdtest()` of
`s->async->prealloc_bufsz / comedi_bytes_per_scan(s)` will be a
divide-by-zero error. To fix this error, call a new function
`comedi_bytes_per_scan_cmd(s, cmd)`, based on the existing
`comedi_bytes_per_scan(s)` but using a specified `struct comedi_cmd` for
its calculations. (Also refactor `comedi_bytes_per_scan()` to call the
new function.)
Once the first cause for the divide-by-zero has been fixed, the second
cause is that `comedi_bytes_per_scan_cmd()` can legitimately return 0 if
the `scan_end_arg` member of the `struct comedi_cmd` being tested is 0.
Fix it by only performing the division (and validating that `stop_arg`
is no more than the maximum value) if `comedi_bytes_per_scan_cmd()`
returns a non-zero value.
The problem was reported on the COMEDI mailing list here:
https://groups.google.com/forum/#!topic/comedi_list/4t9WlHzMhKM
Reported-by: Ivan Vasilyev <grabesstimme@gmail.com> Tested-by: Ivan Vasilyev <grabesstimme@gmail.com> Fixes: f164cbf98fa8 ("staging: comedi: ni_mio_common: add finite regeneration to dio output") Cc: <stable@vger.kernel.org> # 4.6+ Cc: Spencer E. Olson <olsonse@umich.edu> Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suppose more than one non-NPIV FCP device is active on the same channel.
Send I/O to storage and have some of the pending I/O run into a SCSI
command timeout, e.g. due to bit errors on the fibre. Now the error
situation stops. However, we saw FCP requests continue to timeout in the
channel. The abort will be successful, but the subsequent TUR fails.
Scsi_eh starts. The LUN reset fails. The target reset fails. The host
reset only did an FCP device recovery. However, for non-NPIV FCP devices,
this does not close and reopen ports on the SAN-side if other non-NPIV FCP
device(s) share the same open ports.
In order to resolve the continuing FCP request timeouts, we need to
explicitly close and reopen ports on the SAN-side.
This was missing since the beginning of zfcp in v2.6.0 history commit ea127f975424 ("[PATCH] s390 (7/7): zfcp host adapter.").
Note: The FSF requests for forced port reopen could run into FSF request
timeouts due to other reasons. This would trigger an internal FCP device
recovery. Pending forced port reopen recoveries would get dismissed. So
some ports might not get fully reopened during this host reset handler.
However, subsequent I/O would trigger the above described escalation and
eventually all ports would be forced reopen to resolve any continuing FCP
request timeouts due to earlier bit errors.
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: <stable@vger.kernel.org> #3.0+ Reviewed-by: Jens Remus <jremus@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An already deleted SCSI device can exist on the Scsi_Host and remain there
because something still holds a reference. A new SCSI device with the same
H:C:T:L and FCP device, target port WWPN, and FCP LUN can be created. When
we try to unblock an rport, we still find the deleted SCSI device and
return early because the zfcp_scsi_dev of that SCSI device is not
ZFCP_STATUS_COMMON_UNBLOCKED. Hence we miss to unblock the rport, even if
the new proper SCSI device would be in good state.
Therefore, skip deleted SCSI devices when iterating the sdevs of the shost.
[cf. __scsi_device_lookup{_by_target}() or scsi_device_get()]
The following abbreviated trace sequence can indicate such problem:
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000 not ZFCP_STATUS_COMMON_UNBLOCKED
Ready count : n not incremented yet
Running count : 0x00000000
ERP want : 0x01
ERP need : 0xc1 ZFCP_ERP_ACTION_NONE
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x41000000
Ready count : n+1
Running count : 0x00000000
ERP want : 0x01
ERP need : 0x01
...
Area : REC
Level : 4 only with increased trace level
Tag : ertru_l
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000
Request ID : 0x0000000000000000
ERP status : 0x01800000
ERP step : 0x1000
ERP action : 0x01
ERP count : 0x00
NOT followed by a trace record with tag "scpaddy"
for WWPN 0x50050763031bd327.
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Fixes: 6f2ce1c6af37 ("scsi: zfcp: fix rport unblock race with LUN recovery") Cc: <stable@vger.kernel.org> #2.6.32+ Reviewed-by: Jens Remus <jremus@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple
of physical block size") split one conditional into several separate
statements in an effort to provide more accurate warning messages when
a device reports a nonsensical value. However, this reorganization
accidentally dropped the precondition of the reported value being
larger than zero. This lead to a warning getting emitted on devices
that do not report an optimal I/O size at all.
Remain silent if a device does not report an optimal I/O size.
Fixes: a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple of physical block size") Cc: Randy Dunlap <rdunlap@infradead.org> Cc: <stable@vger.kernel.org> Reported-by: Hussam Al-Tayeb <ht990332@gmx.com> Tested-by: Hussam Al-Tayeb <ht990332@gmx.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The scsi_end_request() function calls scsi_cmd_to_driver() indirectly and
hence needs the disk->private_data pointer. Avoid that that pointer is
cleared before all affected I/O requests have finished. This patch avoids
that the following crash occurs:
Cc: Christoph Hellwig <hch@lst.de> Cc: Ming Lei <ming.lei@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Cc: Johannes Thumshirn <jthumshirn@suse.de> Cc: Jason Yan <yanaijie@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reported-by: Jason Yan <yanaijie@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ocfs2_reflink_inodes_lock() can swap the inode1/inode2 variables so that
we always grab cluster locks in order of increasing inode number.
Unfortunately, we forget to swap the inode record buffer head pointers
when we've done this, which leads to incorrect bookkeepping when we're
trying to make the two inodes have the same refcount tree.
This has the effect of causing filesystem shutdowns if you're trying to
reflink data from inode 100 into inode 97, where inode 100 already has a
refcount tree attached and inode 97 doesn't. The reflink code decides
to copy the refcount tree pointer from 100 to 97, but uses inode 97's
inode record to open the tree root (which it doesn't have) and blows up.
This issue causes filesystem shutdowns and metadata corruption!
Link: http://lkml.kernel.org/r/20190312214910.GK20533@magnolia Fixes: 29ac8e856cb369 ("ocfs2: implement the VFS clone_range, copy_range, and dedupe_range features") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Joseph Qi <jiangqi903@gmail.com> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <joseph.qi@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is hitting lockdep warning [1] due to trying to open a fifo
during an execve() operation. But we don't need to open non regular
files during an execve() operation, for all files which we will need are
the executable file itself and the interpreter programs like /bin/sh and
ld-linux.so.2 .
Since the manpage for execve(2) says that execve() returns EACCES when
the file or a script interpreter is not a regular file, and the manpage
for uselib(2) says that uselib() can return EACCES, and we use
FMODE_EXEC when opening for execve()/uselib(), we can bail out if a non
regular file is requested with FMODE_EXEC set.
Since this deadlock followed by khungtaskd warnings is trivially
reproducible by a local unprivileged user, and syzbot's frequent crash
due to this deadlock defers finding other bugs, let's workaround this
deadlock until we get a chance to find a better solution.
Fix commit 56067812d5b0 ("kbuild: modversions: add infrastructure for
emitting relative CRCs") where CRCs are interpreted in host byte order
rather than proper kernel byte order. The bug is conditional on
CONFIG_MODULE_REL_CRCS.
For example, when loading a BE module into a BE kernel compiled with a LE
system, the error "disagrees about version of symbol module_layout" is
produced. A message such as "Found checksum D7FA6856 vs module 5668FAD7"
will be given with debug enabled, which indicates an obvious endian
problem within __kcrctab within the kernel image.
The general solution is to use the macro TO_NATIVE, as is done in
similar cases throughout modpost.c. With this correction it has been
verified that a BE kernel compiled with a LE system accepts BE modules.
This change has also been verified with a LE kernel compiled with a LE
system, in which case TO_NATIVE returns its value unmodified since the
byte orders match. This is by far the common case.
Currently PCM core sets each opened stream forcibly to SUSPENDED state
via snd_pcm_suspend_all() call, and the user-space is responsible for
re-triggering the resume manually either via snd_pcm_resume() or
prepare call. The scheme works fine usually, but there are corner
cases where the stream can't be resumed by that call: the streams
still in OPEN state before finishing hw_params. When they are
suspended, user-space cannot perform resume or prepare because they
haven't been set up yet. The only possible recovery is to re-open the
device, which isn't nice at all. Similarly, when a stream is in
DISCONNECTED state, it makes no sense to change it to SUSPENDED
state. Ditto for in SETUP state; which you can re-prepare directly.
So, this patch addresses these issues by filtering the PCM streams to
be suspended by checking the PCM state. When a stream is in either
OPEN, SETUP or DISCONNECTED as well as already SUSPENDED, the suspend
action is skipped.
To be noted, this problem was originally reported for the PCM runtime
PM on HD-audio. And, the runtime PM problem itself was already
addressed (although not intended) by the code refactoring commits 3d21ef0b49f8 ("ALSA: pcm: Suspend streams globally via device type PM
ops") and 17bc4815de58 ("ALSA: pci: Remove superfluous
snd_pcm_suspend*() calls"). These commits eliminated the
snd_pcm_suspend*() calls from the runtime PM suspend callback code
path, hence the racy OPEN state won't appear while runtime PM.
(FWIW, the race window is between snd_pcm_open_substream() and the
first power up in azx_pcm_open().)
Although the runtime PM issue was already "fixed", the same problem is
still present for the system PM, hence this patch is still needed.
And for stable trees, this patch alone should suffice for fixing the
runtime PM problem, too.
The PCM OSS emulation converts and transfers the data on the fly via
"plugins". The data is converted over the dynamically allocated
buffer for each plugin, and recently syzkaller caught OOB in this
flow.
Although the bisection by syzbot pointed out to the commit 65766ee0bf7f ("ALSA: oss: Use kvzalloc() for local buffer
allocations"), this is merely a commit to replace vmalloc() with
kvmalloc(), hence it can't be the cause. The further debug action
revealed that this happens in the case where a slave PCM doesn't
support only the stereo channels while the OSS stream is set up for a
mono channel. Below is a brief explanation:
At each OSS parameter change, the driver sets up the PCM hw_params
again in snd_pcm_oss_change_params_lock(). This is also the place
where plugins are created and local buffers are allocated. The
problem is that the plugins are created before the final hw_params is
determined. Namely, two snd_pcm_hw_param_near() calls for setting the
period size and periods may influence on the final result of channels,
rates, etc, too, while the current code has already created plugins
beforehand with the premature values. So, the plugin believes that
channels=1, while the actual I/O is with channels=2, which makes the
driver reading/writing over the allocated buffer size.
The fix is simply to move the plugin allocation code after the final
hw_params call.
Fix this by sanitizing dev before using it to index dp->synths.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Fix this by sanitizing info->stream before using it to index
rmidi->streams.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
This belated patch implements Andrew Lunn's request of
"remove the phy_read() and phy_write() functions."
<https://lore.kernel.org/patchwork/comment/902734/>
While seemingly harmless, this causes the switch's user
port PHYs to get registered twice. This is because the
DSA subsystem will create a slave mdio-bus not knowing
that the qca8k_phy_(read|write) accessors operate on
the external mdio-bus. So the same "bus" gets effectively
duplicated.
Cc: stable@vger.kernel.org Fixes: 6b93fb46480a ("net-next: dsa: add new driver for qca8xxx family") Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yauheni Kaliuta pointed out that PTR_TO_STACK store/load verifier test
was failing on powerpc64 BE, and rightfully indicated that the PPC_LD()
macro is not masking away the last two bits of the offset per the ISA,
resulting in the generation of 'lwa' instruction instead of the intended
'ld' instruction.
Segher also pointed out that we can't simply mask away the last two bits
as that will result in loading/storing from/to a memory location that
was not intended.
This patch addresses this by using ldx/stdx if the offset is not
word-aligned. We load the offset into a temporary register (TMP_REG_2)
and use that as the index register in a subsequent ldx/stdx. We fix
PPC_LD() macro to mask off the last two bits, but enhance PPC_BPF_LL()
and PPC_BPF_STL() to factor in the offset value and generate the proper
instruction sequence. We also convert all existing users of PPC_LD() and
PPC_STD() to use these macros. All existing uses of these macros have
been audited to ensure that TMP_REG_2 can be clobbered.
Fixes: 156d0e290e96 ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF") Cc: stable@vger.kernel.org # v4.9+ Reported-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com> Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current cpuidle implementation for i.MX6q, the CPU that sets
'WAIT_UNCLOCKED' and the CPU that returns to 'WAIT_CLOCKED' are always
the same. While the CPU that sets 'WAIT_UNCLOCKED' is in IDLE state of
"WAIT", if the other CPU wakes up and enters IDLE state of "WFI"
istead of "WAIT", this CPU can not wake up at expired time.
Because, in the case of "WFI", the CPU must be waked up by the local
timer interrupt. But, while 'WAIT_UNCLOCKED' is set, the local timer
is stopped, when all CPUs execute "wfi" instruction. As a result, the
local timer interrupt is not fired.
In this situation, this CPU will wake up by IRQ different from local
timer. (e.g. broacast timer)
So, this fix changes CPU to return to 'WAIT_CLOCKED'.
The reason is that kunmap(p_page) was completely left out, so we never
did an unmap for the p_page and the loop unmapping the rbio page was
iterating over the wrong number of stripes: unmapping should be done
with nr_data instead of rbio->real_stripes.
When Filipe added the recursive directory logging stuff in 2f2ff0ee5e430 ("Btrfs: fix metadata inconsistencies after directory
fsync") he specifically didn't take the directory i_mutex for the
children directories that we need to log because of lockdep. This is
generally fine, but can lead to this WARN_ON() tripping if we happen to
run delayed deletion's in between our first search and our second search
of dir_item/dir_indexes for this directory. We expect this to happen,
so the WARN_ON() isn't necessary. Drop the WARN_ON() and add a comment
so we know why this case can happen.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we do a shrinking truncate against an inode which is already present
in the respective log tree and then rename it, as part of logging the new
name we end up logging an inode item that reflects the old size of the
file (the one which we previously logged) and not the new smaller size.
The decision to preserve the size previously logged was added by commit 1a4bcf470c886b ("Btrfs: fix fsync data loss after adding hard link to
inode") in order to avoid data loss after replaying the log. However that
decision is only needed for the case the logged inode size is smaller then
the current size of the inode, as explained in that commit's change log.
If the current size of the inode is smaller then the previously logged
size, we know a shrinking truncate happened and therefore need to use
that smaller size.
$ mount /dev/sdb /mnt
$ od -t x1 -A d /mnt/bar 0000000 ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab
* 0008000
Once we rename the file, we log its name (and inode item), and because
the inode was already logged before in the current transaction, we log it
with a size of 8000 bytes because that is the size we previously logged
(with the first fsync). As part of the rename, besides logging the inode,
we do also sync the log, which is done since commit d4682ba03ef618
("Btrfs: sync log after logging new name"), so the next fsync against our
inode is effectively a no-op, since no new changes happened since the
rename operation. Even if did not sync the log during the rename
operation, the same problem (fize size of 8000 bytes instead of 3000
bytes) would be visible after replaying the log if the log ended up
getting synced to disk through some other means, such as for example by
fsyncing some other modified file. In the example above the fsync after
the rename operation is there just because not every filesystem may
guarantee logging/journalling the inode (and syncing the log/journal)
during the rename operation, for example it is needed for f2fs, but not
for ext4 and xfs.
Fix this scenario by, when logging a new name (which is triggered by
rename and link operations), using the current size of the inode instead
of the previously logged inode size.
A test case for fstests follows soon.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202695 CC: stable@vger.kernel.org # 4.4+ Reported-by: Seulbae Kim <seulbae@gatech.edu> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When I updated the spectre_v2 reporting to handle software count cache
flush I got the logic wrong when there's no software count cache
enabled at all.
The result is that on systems with the software count cache flush
disabled we print:
Which correctly indicates that the count cache is disabled, but
incorrectly says the software count cache flush is enabled.
The root of the problem is that we are trying to handle all
combinations of options. But we know now that we only expect to see
the software count cache flush enabled if the other options are false.
So split the two cases, which simplifies the logic and fixes the bug.
We were also missing a space before "(hardware accelerated)".
The commit identified below adds MC_BTB_FLUSH macro only when
CONFIG_PPC_FSL_BOOK3E is defined. This results in the following error
on some configs (seen several times with kisskb randconfig_defconfig)
Fixed the following build warning:
powerpc-linux-gnu-ld: warning: orphan section `__btb_flush_fixup' from
`arch/powerpc/kernel/head_44x.o' being placed in section
`__btb_flush_fixup'.
In order to protect against speculation attacks on
indirect branches, the branch predictor is flushed at
kernel entry to protect for the following situations:
- userspace process attacking another userspace process
- userspace process attacking the kernel
Basically when the privillege level change (i.e.the kernel
is entered), the branch predictor state is flushed.
In order to protect against speculation attacks on
indirect branches, the branch predictor is flushed at
kernel entry to protect for the following situations:
- userspace process attacking another userspace process
- userspace process attacking the kernel
Basically when the privillege level change (i.e. the
kernel is entered), the branch predictor state is flushed.
In order to flush the branch predictor the guest kernel performs
writes to the BUCSR register which is hypervisor privilleged. However,
the branch predictor is flushed at each KVM entry, so the branch
predictor has been already flushed, so just return as soon as possible
to guest.
In order to protect against speculation attacks (Spectre
variant 2) on NXP PowerPC platforms, the branch predictor
should be flushed when the privillege level is changed.
This patch is adding the infrastructure to fixup at runtime
the code sections that are performing the branch predictor flush
depending on a boot arg parameter which is added later in a
separate patch.
Look for fw-features properties to determine the appropriate settings
for the count cache flush, and then call the generic powerpc code to
set it up based on the security feature flags.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the existing hypercall to determine the appropriate settings for
the count cache flush, and then call the generic powerpc code to set
it up based on the security feature flags.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some CPU revisions support a mode where the count cache needs to be
flushed by software on context switch. Additionally some revisions may
have a hardware accelerated flush, in which case the software flush
sequence can be shortened.
If we detect the appropriate flag from firmware we patch a branch
into _switch() which takes us to a count cache flush sequence.
That sequence in turn may be patched to return early if we detect that
the CPU supports accelerating the flush sequence in hardware.
Add debugfs support for reporting the state of the flush, as well as
runtime disabling it.
And modify the spectre_v2 sysfs file to report the state of the
software flush.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add security feature flags to indicate the need for software to flush
the count cache on context switch, and for the presence of a hardware
assisted count cache flush.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a macro and some helper C functions for patching single asm
instructions.
The gas macro means we can do something like:
1: nop
patch_site 1b, patch__foo
Which is less visually distracting than defining a GLOBAL symbol at 1,
and also doesn't pollute the symbol table which can confuse eg. perf.
These are obviously similar to our existing feature sections, but are
not automatically patched based on CPU/MMU features, rather they are
designed to be manually patched by C code at some arbitrary point.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a subsequent patch we will enable building security.c for Book3E.
However the NXP platforms are not vulnerable to Meltdown, so make the
Meltdown vulnerability reporting PPC_BOOK3S_64 specific.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
[mpe: Split out of larger patch] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we require platform code to call setup_barrier_nospec(). But
if we add an empty definition for the !CONFIG_PPC_BARRIER_NOSPEC case
then we can call it in setup_arch().
Add a config symbol to encode which platforms support the
barrier_nospec speculation barrier. Currently this is just Book3S 64
but we will add Book3E in a future patch.
When I added the spectre_v2 information in sysfs, I included the
availability of the ori31 speculation barrier.
Although the ori31 barrier can be used to mitigate v2, it's primarily
intended as a spectre v1 mitigation. Spectre v2 is mitigated by
hardware changes.
So rework the sysfs files to show the ori31 information in the
spectre_v1 file, rather than v2.
See commit 304ec1b05031 ("x86/uaccess: Use __uaccess_begin_nospec()
and uaccess_try_nospec") and b3bbfb3fb5d2 ("x86: Introduce
__uaccess_begin_nospec() and uaccess_try_nospec") for more detail.
In all cases we are ordering the load from the potentially
user-controlled pointer vs a previous branch based on an access_ok()
check or similar.
Base on a patch from Michal Suchanek.
Signed-off-by: Michal Suchanek <msuchanek@suse.de> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the RFI patching. This is required to be able to disable the
speculation barrier.
Only one barrier type is supported and it does nothing when the
firmware does not enable it. Also re-patching modules is not supported
So the only meaningful thing that can be done is patching out the
speculation barrier at boot when the user says it is not wanted.
Signed-off-by: Michal Suchanek <msuchanek@suse.de> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In my latest patch I missed one rcu_read_unlock(), in case
device is down.
Fixes: 4477138fa0ae ("tun: properly test for IFF_UP") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Same reasons than the ones explained in commit 4179cb5a4c92
("vxlan: test dev->flags & IFF_UP before calling netif_rx()")
netif_rx_ni() or napi_gro_frags() must be called under a strict contract.
At device dismantle phase, core networking clears IFF_UP
and flush_all_backlogs() is called after rcu grace period
to make sure no incoming packet might be in a cpu backlog
and still referencing the device.
A similar protocol is used for gro layer.
Most drivers call netif_rx() from their interrupt handler,
and since the interrupts are disabled at device dismantle,
netif_rx() does not have to check dev->flags & IFF_UP
Virtual drivers do not have this guarantee, and must
therefore make the check themselves.
Fixes: 1bd4978a88ac ("tun: honor IFF_UP in tun_get_user()") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bug that Stan reported is as follows. After a restart, a 16-bit NIC
may be incorrectly identified as a 32-bit NIC and stop working.
mac8390 slot.E: Memory length resource not found, probing
mac8390 slot.E: Farallon EtherMac II-C (type farallon)
mac8390 slot.E: MAC 00:00:c5:30:c2:99, IRQ 61, 32 KB shared memory at 0xfeed0000, 32-bit access.
The bug never arises after a cold start and only intermittently after a
warm start. (I didn't investigate why the bug is intermittent.)
It turns out that memcpy_toio() is deprecated and memcmp_withio() also
has issues. Replacing these calls with mmio accessors fixes the problem.
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com> Fixes: 2964db0f5904 ("m68k: Mac DP8390 update") Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCP/UDP checksum validity was propagated to skb
only if IP checksum is valid.
But for IPv6 there is no validity as there is no checksum in IPv6.
This patch propagates TCP/UDP checksum validity regardless of IP checksum.
Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code") Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com> Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sctp_hdr(skb) only works when skb->transport_header is set properly.
But in Netfilter, skb->transport_header for ipv6 is not guaranteed
to be right value for sctphdr. It would cause to fail to check the
checksum for sctp packets.
So fix it by using offset, which is always right in all places.
v1->v2:
- Fix the changelog.
Fixes: e6d8b64b34aa ("net: sctp: fix and consolidate SCTP checksumming code") Reported-by: Li Shuang <shuali@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ad6c9986bcb62 ("vxlan: Fix GRO cells race condition between
receive and link delete") fixed a race condition for the typical case a vxlan
device is dismantled from the current netns. But if a netns is dismantled,
vxlan_destroy_tunnels() is called to schedule a unregister_netdevice_queue()
of all the vxlan tunnels that are related to this netns.
In vxlan_destroy_tunnels(), gro_cells_destroy() is called and finished before
unregister_netdevice_queue(). This means that the gro_cells_destroy() call is
done too soon, for the same reasons explained in above commit.
So we need to fully respect the RCU rules, and thus must remove the
gro_cells_destroy() call or risk use after-free.
Fixes: 58ce31cca1ff ("vxlan: GRO support at tunnel layer") Signed-off-by: Suanming.Mou <mousuanming@huawei.com> Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the non-XDP case, commit 773225388dae15e72790 ("net: thunderx: Optimize
page recycling for XDP") added code to nicvf_free_rbdr() that, when releasing
the additional receive buffer page reference held for recycling, repeatedly
calls put_page() until the page's _refcount goes to zero. Which results in
the page being freed.
This is not okay if the page's _refcount was greater than 1 (in the non-XDP
case), because nicvf_free_rbdr() should not be subtracting more than what
nicvf_alloc_page() had previously added to the page's _refcount, which was
only 1 (in the non-XDP case).
This can arise if a received packet is still being processed and the receive
buffer (i.e., skb->head) has not yet been freed via skb_free_head() when
nicvf_free_rbdr() is spinning through the aforementioned put_page() loop.
If this should occur, when the received packet finishes processing and
skb_free_head() is called, various problems can ensue. Exactly what, depends on
whether the page has already been reallocated or not, anything from "BUG: Bad
page state ... ", to "Unable to handle kernel NULL pointer dereference ..." or
"Unable to handle kernel paging request...".
So this patch changes nicvf_free_rbdr() to only call put_page() once for pages
held for recycling (in the non-XDP case).
Fixes: 773225388dae ("net: thunderx: Optimize page recycling for XDP") Signed-off-by: Dean Nelson <dnelson@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 773225388dae15e72790 ("net: thunderx: Optimize page recycling for XDP")
added code to nicvf_alloc_page() that inadvertently disables receive buffer
page recycling for the non-XDP case by always NULL'ng the page pointer.
This patch corrects two if-conditionals to allow for the recycling of non-XDP
mode pages by only setting the page pointer to NULL when the page is not ready
for recycling.
Fixes: 773225388dae ("net: thunderx: Optimize page recycling for XDP") Signed-off-by: Dean Nelson <dnelson@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a dual stack tcp listener accepts an ipv4 flow,
it should not attempt to use an ipv6 header or tcp_v6_iif() helper.
Fixes: 1397ed35f22d ("ipv6: add flowinfo for tcp6 pkt_options for all cases") Fixes: df3687ffc665 ("ipv6: add the IPV6_FL_F_REFLECT flag to IPV6_FL_A_GET") Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As it stands if a shrink is delayed because of an outstanding
rehash, we will go into a rescheduling loop without ever doing
the rehash.
This patch fixes this by still carrying out the rehash and then
rescheduling so that we can shrink after the completion of the
rehash should it still be necessary.
The return value of EEXIST captures this case and other cases
(e.g., another thread expanded/rehashed the table at the same
time) where we should still proceed with the rehash.
Fixes: da20420f83ea ("rhashtable: Add nested tables") Reported-by: Josh Elsasser <jelsasser@appneta.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Tested-by: Josh Elsasser <jelsasser@appneta.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using fanouts with AF_PACKET, the demux functions such as
fanout_demux_cpu will return an index in the fanout socket array, which
corresponds to the selected socket.
The ordering of this array depends on the order the sockets were added
to a given fanout group, so for FANOUT_CPU this means sockets are bound
to cpus in the order they are configured, which is OK.
However, when stopping then restarting the interface these sockets are
bound to, the sockets are reassigned to the fanout group in the reverse
order, due to the fact that they were inserted at the head of the
interface's AF_PACKET socket list.
This means that traffic that was directed to the first socket in the
fanout group is now directed to the last one after an interface restart.
In the case of FANOUT_CPU, traffic from CPU0 will be directed to the
socket that used to receive traffic from the last CPU after an interface
restart.
This commit introduces a helper to add a socket at the tail of a list,
then uses it to register AF_PACKET sockets.
Note that this changes the order in which sockets are listed in /proc and
with sock_diag.
Fixes: dc99f600698d ("packet: Add fanout support") Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In netdev_queue_add_kobject and rx_queue_add_kobject,
if sysfs_create_group failed, kobject_put will call
netdev_queue_release to decrease dev refcont, however
dev_hold has not be called. So we will see this while
unregistering dev:
unregister_netdevice: waiting for bcsh0 to become free. Usage count = -1
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: d0d668371679 ("net: don't decrement kobj reference count on init failure") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using 16K DMA buffers and ring mode, the DES3 refill is not working
correctly as the function is using a bogus pointer for checking the
private data. As a result stale pointers will remain in the RX descriptor
ring, so DMA will now likely overwrite/corrupt some already freed memory.
As simple reproducer, just receive some UDP traffic:
# ifconfig eth0 down; ifconfig eth0 mtu 9000; ifconfig eth0 up
# iperf3 -c 192.168.253.40 -u -b 0 -R
If you didn't crash by now check the RX descriptors to find non-contiguous
RX buffers:
# ping -s 8200 192.168.253.40
PING 192.168.253.40 (192.168.253.40) 8200(8228) bytes of data.
8208 bytes from 192.168.253.40: icmp_seq=1 ttl=64 time=1.00 ms
wrong data byte #8144 should be 0xd0 but was 0x88
Fix the wrong pointer. Also we must refill DES3 only if the DMA buffer
size is 16K.
Fixes: 54139cf3bb33 ("net: stmmac: adding multiple buffers for rx") Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Acked-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rose_write_internal() uses a temp buffer of 100 bytes, but a manual
inspection showed that given arbitrary input, rose_create_facilities()
can fill up to 110 bytes.
Lets use a tailroom of 256 bytes for peace of mind, and remove
the bounce buffer : we can simply allocate a big enough skb
and adjust its length as needed.
syzbot report :
BUG: KASAN: stack-out-of-bounds in memcpy include/linux/string.h:352 [inline]
BUG: KASAN: stack-out-of-bounds in rose_create_facilities net/rose/rose_subr.c:521 [inline]
BUG: KASAN: stack-out-of-bounds in rose_write_internal+0x597/0x15d0 net/rose/rose_subr.c:116
Write of size 7 at addr ffff88808b1ffbef by task syz-executor.0/24854
Memory state around the buggy address: ffff88808b1ffa80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff88808b1ffb00: 00 00 00 00 00 00 00 00 f1 f1 f1 f1 00 00 00 03
>ffff88808b1ffb80: f2 f2 00 00 00 00 00 00 00 00 00 00 00 00 04 f3
^ ffff88808b1ffc00: f3 f3 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00 ffff88808b1ffc80: 00 00 00 00 00 00 00 f1 f1 f1 f1 f1 f1 01 f2 01
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit fc62814d690c ("net/packet: fix 4gb buffer limit due to overflow check")
one can now allocate packet ring buffers >= UINT_MAX. However, syzkaller
found that that triggers a warning:
Christoph reported a stall while peeking datagram with an offset when
busy polling is enabled. __skb_try_recv_datagram() uses as the loop
termination condition 'queue empty'. When peeking, the socket
queue can be not empty, even when no additional packets are received.
Address the issue explicitly checking for receive queue changes,
as currently done by __skb_wait_for_more_packets().
Fixes: 2b5cd0dfa384 ("net: Change return type of sk_busy_loop from bool to void") Reported-and-tested-by: Christoph Paasch <cpaasch@apple.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device ID alone does not uniquely identify a device. Test both the
vendor and device ID to make sure we don't mistakenly think some other
vendor's 0xB410 device is a Digium HFC4S. Also, instead of the bare hex
ID, use the same constant (PCI_DEVICE_ID_DIGIUM_HFC4S) used in the device
ID table.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In genl_register_family(), when idr_alloc() fails,
we forget to free the memory we possibly allocate for
family->attrbuf.
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: 2ae0f17df1cd ("genetlink: use idr to track families") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a dual stack dccp listener accepts an ipv4 flow,
it should not attempt to use an ipv6 header or
inet6_iif() helper.
Fixes: 3df80d9320bc ("[DCCP]: Introduce DCCPv6") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently stmmac driver not copying the valid ethernet
MAC address to MAC registers. This patch takes care
of updating the MAC register with MAC address.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
User space Android code identifies pixclock == 0 as a sign for emulation
and will set the frame rate to 60 fps when reading this value, which is
the desired outcome.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Roman Kiryanov <rkir@google.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function l2cap_get_conf_opt will return L2CAP_CONF_OPT_SIZE + opt->len
as length value. The opt->len however is in control over the remote user
and can be used by an attacker to gain access beyond the bounds of the
actual packet.
To prevent any potential leak of heap memory, it is enough to check that
the resulting len calculation after calling l2cap_get_conf_opt is not
below zero. A well formed packet will always return >= 0 here and will
end with the length value being zero after the last option has been
parsed. In case of malformed packets messing with the opt->len field the
length value will become negative. If that is the case, then just abort
and ignore the option.
In case an attacker uses a too short opt->len value, then garbage will
be parsed, but that is protected by the unknown option handling and also
the option parameter size checks.
When doing option parsing for standard type values of 1, 2 or 4 octets,
the value is converted directly into a variable instead of a pointer. To
avoid being tricked into being a pointer, check that for these option
types that sizes actually match. In L2CAP every option is fixed size and
thus it is prudent anyway to ensure that the remote side sends us the
right option size along with option paramters.
If the option size is not matching the option type, then that option is
silently ignored. It is a protocol violation and instead of trying to
give the remote attacker any further hints just pretend that option is
not present and proceed with the default values. Implementation
following the specification and its qualification procedures will always
use the correct size and thus not being impacted here.
To keep the code readable and consistent accross all options, a few
cosmetic changes were also required.
The way that 'strncat' is used here raised a warning in gcc-8:
drivers/net/wireless/ath/ath10k/wmi.c: In function 'ath10k_wmi_tpc_stats_final_disp_tables':
drivers/net/wireless/ath/ath10k/wmi.c:4649:4: error: 'strncat' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
Effectively, this is simply a strcat() but the use of strncat() suggests
some form of overflow check. Regardless of whether this might actually
overflow, using strlcat() instead of strncat() avoids the warning and
makes the code more robust.
Fixes: bc64d05220f3 ("ath10k: debugfs support to get final TPC stats for 10.4 variants") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before this patch the enable signal was set before the PWM signal and
vice-versa on power off. This sequence is wrong, at least, it is on
the different panels datasheets that I checked, so I inverted the sequence
to follow the specs.
For reference the following panels have the mentioned sequence:
- N133HSE-EA1 (Innolux)
- N116BGE (Innolux)
- N156BGE-L21 (Innolux)
- B101EAN0 (Auo)
- B101AW03 (Auo)
- LTN101NT05 (Samsung)
- CLAA101WA01A (Chunghwa)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Acked-by: Daniel Thompson <daniel.thompson@linaro.org> Acked-by: Jingoo Han <jingoohan1@gmail.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prevents the 'global_tunables_lock' mutex from being
unlocked before being locked. This mutex is not locked if the
sugov_kthread_create() function fails.
Signed-off-by: Jules Maselbas <jules.maselbas@arm.com> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Chris Redpath <chris.redpath@arm.com> Cc: Dietmar Eggermann <dietmar.eggemann@arm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Patrick Bellasi <patrick.bellasi@arm.com> Cc: Stephen Kyle <stephen.kyle@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Cc: nd@arm.com Link: http://lkml.kernel.org/r/20180329144301.38419-1-jules.maselbas@arm.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we convert one large time values to rtc_time, in the original formula
'days * 86400' can be overflowed in 'unsigned int' type to make the formula
get one incorrect remain seconds value. Thus we can use div_s64_rem()
function to avoid this situation.
After commit 723288836628 ("of: restrict DMA configuration"),
of_dma_configure() doesn't configure the coherent_dma_mask/dma_mask
of endpoint function device (since it doesn't have a DT node associated
with and hence no dma-ranges property), resulting in
dma_alloc_coherent() (used in pci_epf_alloc_space()) to fail.
Fix it by making dma_alloc_coherent() use EPC's device for allocating
memory address.
Link: http://lkml.kernel.org/r/64d63468-d28f-8fcd-a6f3-cf2a6401c8cb@ti.com Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: tweaked commit log] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Rob Herring <robh@kernel.org> Cc: Christoph Hellwig <hch@lst.de> Tested-by: Cyrille Pitchen <cyrille.pitchen@free-electrons.com> Tested-by: Niklas Cassel <niklas.cassel@axis.com> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Certain registers that pcie-designware-ep tries to write to are read-only
registers. However, these registers can become read/write if we first
enable the DBI_RO_WR_EN bit. Set/unset the DBI_RO_WR_EN bit before/after
writing these registers.
Previously, dw_pcie_ep_set_msi() wrote all bits in the Message Control
register, thus overwriting the PCI_MSI_FLAGS_64BIT bit.
By clearing the PCI_MSI_FLAGS_64BIT bit, we break MSI
on systems where the RC has set a 64 bit MSI address.
Fix dw_pcie_ep_set_msi() so that it only sets MMC bits.
Since the command type of UTRD in UFS 2.1 specification is the same with
UFS 2.0. And it assumes the future UFS specification will follow the
same definition.
Signed-off-by: kehuanlin <kehuanlin@pinecone.net> Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current int_sqrt() computation is sub-optimal for the case of small
@x. Which is the interesting case when we're going to do cumulative
distribution functions on idle times, which we assume to be a random
variable, where the target residency of the deepest idle state gives an
upper bound on the variable (5e6ns on recent Intel chips).
In the case of small @x, the compute loop:
while (m != 0) {
b = y + m;
y >>= 1;
if (x >= b) {
x -= b;
y += m;
}
m >>= 2;
}
can be reduced to:
while (m > x)
m >>= 2;
Because y==0, b==m and until x>=m y will remain 0.
And while this is computationally equivalent, it runs much faster
because there's less code, in particular less branches.
Averages computed over all values <128k using a LFSR to generate order.
Cold numbers have a LFSR based branch trace buffer 'confuser' ran between
each int_sqrt() invocation.
Link: http://lkml.kernel.org/r/20171020164644.876503355@infradead.org Fixes: 30493cc9dddb ("lib/int_sqrt.c: optimize square root algorithm") Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Suggested-by: Anshul Garg <aksgarg1989@gmail.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Will Deacon <will.deacon@arm.com> Cc: Joe Perches <joe@perches.com> Cc: David Miller <davem@davemloft.net> Cc: Matthew Wilcox <mawilcox@microsoft.com> Cc: Kees Cook <keescook@chromium.org> Cc: Michael Davidson <md@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently we found the audio jack detection stop working after suspend
on many machines with Realtek codec. Sometimes the audio selection
dialogue didn't show up after users plugged headhphone/headset into
the headset jack, sometimes after uses plugged headphone/headset, then
click the sound icon on the upper-right corner of gnome-desktop, it
also showed the speaker rather than the headphone.
The root cause is that before suspend, the codec already call the
runtime_suspend since this codec is not used by any apps, then in
resume, it will not call runtime_resume for this codec. But for some
realtek codec (so far, alc236, alc255 and alc891) with the specific
BIOS, if it doesn't run runtime_resume after suspend, all codec
functions including jack detection stop working anymore.
This problem existed for a long time, but it was not exposed, that is
because when problem happens, if users play sound or open
sound-setting to check audio device, this will trigger calling to
runtime_resume (via snd_hda_power_up), then the codec starts working
again before users notice this problem.
Since we don't know how many codec and BIOS combinations have this
problem, to fix it, let the driver call runtime_resume for all codecs
in pm_resume, maybe for some codecs, this is not needed, but it is
harmless. After a codec is runtime resumed, if it is not used by any
apps, it will be runtime suspended soon and furthermore we don't run
suspend frequently, this change will not add much power consumption.
Fixes: cc72da7d4d06 ("ALSA: hda - Use standard runtime PM for codec power-save control") Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we deal with single codec and suspend codec callbacks for
all S3, S4 and runtime PM handling. But it turned out that we want
distinguish the call patterns sometimes, e.g. for applying some init
sequence only at probing and restoring from hibernate.
This patch slightly modifies the common PM callbacks for HD-audio
codec and stores the currently processed PM event in power_state of
the codec's device.power field, which is currently unused. The codec
callback can take a look at this event value and judges which purpose
it's being called.
Tetsuo Handa had reported he saw an incorrect "downgrading a read lock"
warning right after a previous lockdep warning. It is likely that the
previous warning turned off lock debugging causing the lockdep to have
inconsistency states leading to the lock downgrade warning.
Fix that by add a check for debug_locks at the beginning of
__lock_downgrade().
Debugged-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Reported-by: syzbot+53383ae265fb161ef488@syzkaller.appspotmail.com Signed-off-by: Waiman Long <longman@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Link: https://lkml.kernel.org/r/1547093005-26085-1-git-send-email-longman@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the ORC unwinder is invoked for an oops caused by IP==0,
it currently has no idea what to do because there is no debug information
for the stack frame of NULL.
But if RIP is NULL, it is very likely that the last successfully executed
instruction was an indirect CALL/JMP, and it is possible to unwind out in
the same way as for the first instruction of a normal function. Hardcode
a corresponding ORC entry.
With an artificially-added NULL call in prctl_set_seccomp(), before this
patch, the trace is:
prctl_set_seccomp() still doesn't show up in the trace because for some
reason, tail call optimization is only disabled in builds that use the
frame pointer unwinder.
Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: syzbot <syzbot+ca95b2b7aef9e7cbd6ab@syzkaller.appspotmail.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Michal Marek <michal.lkml@markovi.net> Cc: linux-kbuild@vger.kernel.org Link: https://lkml.kernel.org/r/20190301031201.7416-2-jannh@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the frame unwinder is invoked for an oops caused by a call to NULL, it
currently skips the parent function because BP still points to the parent's
stack frame; the (nonexistent) current function only has the first half of
a stack frame, and BP doesn't point to it yet.
Add a special case for IP==0 that calculates a fake BP from SP, then uses
the real BP for the next frame.
Note that this handles first_frame specially: Return information about the
parent function as long as the saved IP is >=first_frame, even if the fake
BP points below it.
With an artificially-added NULL call in prctl_set_seccomp(), before this
patch, the trace is:
Delay the drm_modeset_acquire_init() until after we check for an
allocation failure so that we can return immediately upon error without
having to unwind.
WARNING: lock held when returning to user space!
4.20.0+ #174 Not tainted
------------------------------------------------
syz-executor556/8153 is leaving the kernel with locks still held!
1 lock held by syz-executor556/8153:
#0: 000000005100c85c (crtc_ww_class_acquire){+.+.}, at:
set_property_atomic+0xb3/0x330 drivers/gpu/drm/drm_mode_object.c:462
Reported-by: syzbot+6ea337c427f5083ebdf2@syzkaller.appspotmail.com Fixes: 144a7999d633 ("drm: Handle properties in the core for atomic drivers") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Sean Paul <sean@poorly.run> Cc: David Airlie <airlied@linux.ie> Cc: <stable@vger.kernel.org> # v4.14+ Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181230122842.21917-1-chris@chris-wilson.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It could use ioctl to set hci uart proto, but there is
a use-after-free issue when hci_uart_register_dev() fail in
hci_uart_set_proto(), see stack above, fix this by setting
HCI_UART_PROTO_READY bit only when hci_uart_register_dev()
return success.
Reported-by: syzbot+899a33dc0fa0dbaf06a6@syzkaller.appspotmail.com Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reviewed-by: Jeremy Cline <jcline@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hci_dev struct hdev is referenced in work queues and timers started
by open() in some protocols. This creates a race between the
initialization function and the work or timer which can result hdev
being dereferenced while it is still null.
The syzbot report contains a reliable reproducer which causes a null
pointer dereference of hdev in hci_uart_write_work() by making the
memory allocation for hdev fail.
To fix this, ensure hdev is valid from before calling a protocol's
open() until after calling a protocol's close().
When releasing socket, it is possible to enter hci_sock_release() and
hci_sock_dev_event(HCI_DEV_UNREG) at the same time in different thread.
The reference count of hdev should be decremented only once from one of
them but if storing hdev to local variable in hci_sock_release() before
detached from socket and setting to NULL in hci_sock_dev_event(),
hci_dev_put(hdev) is unexpectedly called twice. This is resolved by
referencing hdev from socket after bt_sock_unlink() in
hci_sock_release().
h4_recv_buf() callers store the return value to socket buffer and
recursively pass the buffer to h4_recv_buf() without protection. So,
ERR_PTR returned from h4_recv_buf() can be dereferenced, if called again
before setting the socket buffer to NULL from previous error. Check if
skb is ERR_PTR in h4_recv_buf().
projects / arm / linux.git / log