Eric Blake [Wed, 9 Jun 2010 18:35:49 +0000 (12:35 -0600)]
build: restore operation of bit-rotted 'make cov'
'./autobuild.sh' with lcov installed discovered that our
coverage support has been bit-rotting for a while. This
restores it back to a successful state, although I have
not yet spent any time looking through the resulting files to
look for low-hanging fruit in the unit test coverage front.
* configure.ac: Clear COMPILER_FLAGS at right place.
* Makefile.am (cov): Newer genhtml no longer likes plain -s.
* m4/compiler-flags.m4 (gl_COMPILER_FLAGS): Don't AC_SUBST
COMPILER_FLAGS; it is a shell variable for use in configure only.
* src/Makefile.am (AM_CFLAGS, AM_LDFLAGS): New variables, to make
it easier to provide global flag additions. Use throughout, to
uniformly apply coverage flags.
* .gitignore: Globally ignore gcov output.
* daemon/.gitignore: Simplify.
* src/.gitignore: Likewise.
* tests/.gitignore: Likewise.
Eric Blake [Thu, 29 Jul 2010 19:27:58 +0000 (13:27 -0600)]
build: fix 'make syntax-check' failure
src/lxc/veth.c:150: VIR_DEBUG(_("Failed to delete '%s' (%d)"),
src/lxc/veth.c:188: VIR_DEBUG(_("Failed to disable '%s' (%d)"),
maint.mk: do not mark these strings for translation
Previously, the functions in src/lxc/veth.c could sometimes return
positive values on failure rather than -1. This made accurate error
reporting difficult, and led to one failure to catch an error in a
calling function.
This patch makes all the functions in veth.c consistently return 0 on
success, and -1 on failure. It also fixes up the callers to the veth.c
functions where necessary.
It will not fix the bug, but should unveil what happens.
* po/POTFILES.in - add veth.c, which previously had no translatable strings
* src/lxc/lxc_controller.c
* src/lxc/lxc_container.c
* src/lxc/lxc_driver.c - fixup callers to veth.c, and remove error logs,
as they are now done in veth.c
* src/lxc/veth.c - make all functions consistently return -1 on error.
* src/lxc/veth.h - use ATTRIBUTE_NONNULL to protect against NULL args.
Chris Lalancette [Wed, 28 Jul 2010 18:07:08 +0000 (14:07 -0400)]
Fix a potential race in pciInitDevice.
If detecting the FLR flag of a pci device fails, then we
could run into the situation of trying to close a file
descriptor twice, once in pciInitDevice() and once in pciFreeDevice().
Fix that by removing the pciCloseConfig() in pciInitDevice() and
just letting pciFreeDevice() handle it.
Thanks to Chris Wright for pointing out this problem.
While we are at it, fix an error check. While it would actually
work as-is (since success returns 0), it's still more clear to
check for < 0 (as the rest of the code does).
Signed-off-by: Chris Lalancette <clalance@redhat.com>
All <console> devices now export a <target> type attribute. QEMU defaults
to 'serial', UML defaults to 'uml, xen can be either 'serial' or 'xen'
depending on fullvirt. Understandably there is lots of test fallout.
This will be used to differentiate between a serial vs. virtio console for
QEMU.
domain conf: Rename character prop targetType -> deviceType
There is actually a difference between the character device type (serial,
parallel, channel, ...) and the target type (virtio, guestfwd). Currently
they are awkwardly conflated.
Start to pull them apart by renaming targetType -> deviceType. This is
an entirely mechanical change.
Gerhard Stenzel [Wed, 28 Jul 2010 14:17:21 +0000 (16:17 +0200)]
fix handling of PORT_PROFILE_RESPONSE_INPROGRESS netlink message
During function test of the 802.1Qbg implementation in lldpad we came
across a small problem in the handling of the netlink message
corresponding to PORT_PROFILE_RESPONSE_INPROGRESS. This should not
result in returning the default rc=1.
- src/util/macvtap.c: fix getPortProfileStatus() to return 0 in that
case and also fix an indentation problem
Eric Blake [Fri, 23 Jul 2010 20:28:31 +0000 (14:28 -0600)]
maint: turn on gcc logical-op checking
This would have detected the bug in commit 38ad33931 (Aug 09), which
we missed until commit f828ca35 (Jul 10); over 11 months later.
However, on Fedora 13, it also triggers LOTS of warnings from
the libcurl-devel header for two files:
esx/esx_vi.c: In function 'esxVI_CURL_Perform':
esx/esx_vi.c:232: error: logical '&&' with non-zero constant will always evaluate as true [-Wlogical-op]
esx/esx_vi.c:232: error: logical '&&' with non-zero constant will always evaluate as true [-Wlogical-op]
esx/esx_vi.c:232: error: logical '&&' with non-zero constant will always evaluate as true [-Wlogical-op]
...
xenapi/xenapi_driver.c: In function 'call_func':
xenapi/xenapi_driver.c:1872: error: logical '&&' with non-zero constant will always evaluate as true [-Wlogical-op]
xenapi/xenapi_driver.c:1872: error: logical '&&' with non-zero constant will always evaluate as true [-Wlogical-op]
xenapi/xenapi_driver.c:1872: error: logical '&&' with non-zero constant will always evaluate as true [-Wlogical-op]
...
libcurl allows to disable the type-checking code that triggers those
warnings, along with the reduction in type-safety of calls to some
libcurl functions. I figure this is worth the improved compiler
checking throughout the rest of libvirt.
* acinclude.m4 (--enable-compile-warnings=error): Add -Wlogical-op.
* configure.ac: Add -DCURL_DISABLE_TYPECHECK to LIBCURL_CFLAGS to
avoid compilation warning.
Suggested by Daniel P. Berrange.
Tweaked by Matthias Bolte.
Eric Blake [Tue, 27 Jul 2010 18:05:27 +0000 (12:05 -0600)]
libvirt-guests: detect invalid arguments
Reject extra arguments.
Return the correct status for unknown arguments, as mandated by
https://fedoraproject.org/wiki/Packaging/SysVInitScript
Add --help, as a permitted extension.
* daemon/libvirt-guests.init.in (usage): New function. Use it in
more places, and return correct value.
Invert logic for checking for QEMU disk cache options
QEMU has had two different syntax for disk cache options
Old: on|off
New: writeback|writethrough|none
QEMU recently added another 'unsafe' option which broke the
libvirt check. We can avoid this & future breakage, if we
do a negative check for the old syntax, instead of a positive
check for the new syntax
Which maps to -boot,menu=on|off on the QEMU command line.
I decided to use an explicit 'enable' attribute rather than just make the
bootmenu element boolean. This allows us to treat lack of a bootmenu element
as 'use hypervisor default'.
libvirt-guests: Don't throw errors if libvirtd is not installed
When only client parts of libvirt are installed (i.e., no libvirtd
daemon), libvirt-guests init script in its default configuration would
throw seriously looking errors during host shutdown:
Running guests on default URI: error: unable to connect to
'/var/run/libvirt/libvirt-sock', libvirtd may need to be started: No
such file or directory
error: failed to connect to the hypervisor
This patch changes the script to print rather harmless message in that
situation:
Running guests on default URI: libvirtd not installed; skipping this
URI.
Chris Lalancette [Fri, 23 Jul 2010 19:03:29 +0000 (15:03 -0400)]
Force FLR on for buggy SR-IOV devices.
Some buggy PCI devices actually support FLR, but
forget to advertise that fact in their PCI config space.
However, Virtual Functions on SR-IOV devices are
*required* to support FLR by the spec, so force has_flr
on if this is a virtual function.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Eric Blake [Mon, 26 Jul 2010 16:38:30 +0000 (10:38 -0600)]
build: fix VPATH builds
After the recent libvirt-qemu library addition, VPATH builds fail with:
CC libvirt_qemu_la-libvirt-qemu.lo
In file included from ../../src/libvirt-qemu.c:29:
../../include/libvirt/libvirt-qemu.h:17:22: error: libvirt.h: No such file or directory
...
CCLD libvirt-qmeu.la
/usr/bin/ld: cannot open linker script file libvirt_qemu.syms: No such file or directory
This fixes both issues (there are still some documentation VPATH issues,
but those don't show up with 'make check').
* configure.ac (LIBVIRT_QEMU_SYMBOL_FILE): While libvirt.syms is
generated and lives in $(builddir), libvirt_qemu.syms is static
and lives in $(srcdir).
* include/libvirt/libvirt-qemu.h (includes): Pull in libvirt.h via
the public location, since this is a public header.
Chris Wright [Mon, 26 Jul 2010 16:43:04 +0000 (18:43 +0200)]
pciResetDevice: use inactive devices to determine safe reset
When doing a PCI secondary bus reset, we must be sure that there are no
active devices on the same bus segment. The active device tracking is
designed to only track host devices that are active in use by guests.
This ignores host devices that are actively in use by the host. So the
current logic will reset host devices.
Switch this logic around and allow sbus reset when we are assigning all
devices behind a bridge to the same guest at guest startup or as a result
of a single attach-device command.
* src/util/pci.h: change signature of pciResetDevice to add an
inactive devices list
* src/qemu/qemu_driver.c src/xen/xen_driver.c: use (or not) the new
functionality of pciResetDevice() depending on the place of use
* src/util/pci.c: implement the interface and logic changes
Chris Wright [Mon, 26 Jul 2010 16:34:24 +0000 (18:34 +0200)]
qemudDomainAttachHostPciDevice refactor to use new helpers
- src/qemu/qemu_driver.c: Eliminate code duplication by using the new
helpers qemuPrepareHostdevPCIDevices and qemuDomainReAttachHostdevDevices.
This reduces the number of open coded calls to pciResetDevice.
Chris Wright [Mon, 26 Jul 2010 16:23:17 +0000 (18:23 +0200)]
Add helpers qemuPrepareHostdevPCIDevice and qemuDomainReAttachHostdevDevices
- src/qemu/qemu_driver.c: These new helpers take hostdev list and count
directly rather than getting them indirectly from domain definition.
This will allow reuse for the attach-device case.
Chris Wright [Mon, 26 Jul 2010 16:17:20 +0000 (18:17 +0200)]
qemuGetPciHostDeviceList take hostdev list directly
- src/qemu/qemu_driver.c: Update qemuGetPciHostDeviceList to take a
hostdev list and count directly, rather than getting this indirectly
from domain definition. This will allow reuse for the attach-device case.
esx: Add vpx:// scheme to allow direct connection to a vCenter
Add a pointer to the primary context of a connection and use it in all
driver functions that don't dependent on the context type. This includes
almost all functions that deal with a virDomianPtr. Therefore, using
a vpx:// connection allows you to perform all the usual domain related
actions like start, destroy, suspend, resume, dumpxml etc.
Some functions that require an explicitly specified ESX server don't work
yet. This includes the host UUID, the hostname, the general node info, the
max vCPU count and the free memory. Also not working yet are migration and
defining new domains.
Since 070f61002f47b602c15d1e4950a122ac9edefe1b the vcenter query
parameter has been ignored, because the refactoring to use
esxUtil_ParseQuery was incomplete. This effectively broke migration,
because the vcenter query parameter is essential for a migration.
virt-aa-helper-test: Fix failure due to the new disk format probing option
Commit 68719c4bddb85fbcc931a5b7d99ac7c8a0af09b0 added the disk format
probing option. This makes virt-aa-helper-test fail because the domain
config didn't specifiy the disk format and it didn't pass '-p 1' to
virt-aa-helper to allow disk format probing.
Specify the disk format in the domain config. Pass the '-p 1' option
to virt-aa-helper for the test case with two disks. This way this test
also covers this new option.
Commit a8853344994a7c6aaca882a5e949ab5536821ab5 added this
function and wrapped vah_add_file in it. vah_add_file may
return -1, 0, 1. It returns 1 in case the call to valid_path
detects a restricted file. The original code treated a return
value != 0 as error. The refactored code treats a return
value < 0 as error. This triggers segfault in virt-aa-helper
and breaks virt-aa-helper-test for the restricted file tests.
virt-aa-helper used to ignore errors when opening files.
Commit a8853344994a7c6aaca882a5e949ab5536821ab5 refactored
the related code and changed this behavior. virt-aa-helper
didn't ignore open errors anymore and virt-aa-helper-test
fails.
Make sure that virt-aa-helper ignores open errors again.
Chris Lalancette [Sat, 17 Apr 2010 02:09:25 +0000 (22:09 -0400)]
Qemu remote protocol.
Since we are adding a new "per-hypervisor" protocol, we
make it so that the qemu remote protocol uses a new
PROTOCOL and PROGRAM number. This allows us to easily
distinguish it from the normal REMOTE protocol.
This necessitates changing the proc in remote_message_header
from a "remote_procedure" to an "unsigned", which should
be the same size (and thus preserve the on-wire protocol).
Changes since v1:
- Fixed up a couple of script problems in remote_generate_stubs.pl
- Switch an int flag to a bool in dispatch.c
Changes since v2:
- None
Changes since v3:
- Change unsigned proc to signed proc, to conform to spec
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Chris Lalancette [Sat, 17 Apr 2010 02:12:45 +0000 (22:12 -0400)]
Qemu arbitrary monitor commands.
Implement the qemu driver's virDomainQemuMonitorCommand
and hook it into the API entry point.
Changes since v1:
- Rename the (external) qemuMonitorCommand to qemuDomainMonitorCommand
- Add virCheckFlags to qemuDomainMonitorCommand
Changes since v2:
- Drop ATTRIBUTE_UNUSED from the flags
Changes since v3:
- Add a flag to priv so we only print out monitor command warning once. Note
that this has not been plumbed into qemuDomainObjPrivateXMLFormat or
qemuDomainObjPrivateXMLParse, which means that if you run a monitor command,
restart libvirtd, and then run another monitor command, you may get an
an erroneous VIR_INFO. It's a pretty minor matter, and I didn't think it
warranted the additional code.
- Add BeginJob/EndJob calls around EnterMonitor/ExitMonitor
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Chris Lalancette [Tue, 13 Apr 2010 18:02:46 +0000 (14:02 -0400)]
Qemu Monitor API entry point.
Add the library entry point for the new virDomainQemuMonitorCommand()
entry point. Because this is not part of the "normal" libvirt API,
it gets its own header file, library file, and will eventually
get its own over-the-wire protocol later in the series.
Changes since v1:
- Go back to using the virDriver table for qemuDomainMonitorCommand, due to
linking issues
- Added versioning information to the libvirt-qemu.so
Changes since v2:
- None
Changes since v3:
- Add LGPL header to libvirt-qemu.c
- Make virLibConnError and virLibDomainError macros instead of function calls
Changes since v4:
- Move exported symbols to libvirt_qemu.syms
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Chris Lalancette [Mon, 19 Apr 2010 20:34:00 +0000 (16:34 -0400)]
Handle arbitrary qemu command-lines in qemuParseCommandLine.
Now that we have the ability to specify arbitrary qemu
command-line parameters in the XML, use it to handle unknown
command-line parameters when doing a native-to-xml conversion.
Changes since v1:
- Rename num_extra to num_args
- Fix up a memory leak on an error path
Changes since v2:
- Add a VIR_WARN when adding the argument via qemu:arg
Changes since v3:
- None
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Changes since v1:
- Change the <qemu:arg>arg</qemu:arg> XML to <qemu:arg value='arg'/> XML
- Fix up some memory leaks in qemuDomainDefNamespaceParse
- Rename num_extra and extra to num_args and args, respectively
- Fixed up some error messages
- Make sure to escape user-provided data in qemuDomainDefNamespaceFormatXML
Changes since v2:
- Add checking to ensure environment variable names are valid
- Invert the logic in qemuDomainDefNamespaceFormatXML to return early
Changes since v3:
- Change strspn() to c_isalpha() check of first letter of environment variable
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Chris Lalancette [Sat, 17 Apr 2010 03:08:29 +0000 (23:08 -0400)]
Add namespace callback hooks to domain_conf.
This patch adds namespace XML parsers to be hooked into
the main domain parser. This allows for individual hypervisor
drivers to add per-namespace XML into the main domain XML.
Changes since v1:
- Use a statically declared table for caps->ns, removing the need to
allocate/free it.
Changes since v2:
- None
Changes since v3:
- None
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Philipp Hahn [Tue, 13 Jul 2010 08:54:26 +0000 (10:54 +0200)]
Fix SEGV on exit after domainEventDeregister()
When the last callback is removed using domainEventDeregister(), the
events dispatcher is deregistered from the C-library, but
domainEventsCallbacks is still an empty list.
On shutdown __del__() deregisters the dispatacher again, which SEGVs
# You need the event-loop implementation from the Python examples;
# give the file a name which is importable by Python.
ln examples/domain-events/events-python/event-test.py eloop.py
python -c 'from eloop import *
import sys
def dump(*args): print " ".join(map(str, args))
virEventLoopPureStart()
c = libvirt.open("xen:///")
c.domainEventRegister(dump, None)
c.domainEventDeregister(dump)
sys.exit(0)'
domainEventDeregister() needs to delete domainEventCallbacks so subsequent
calls to __del__() and domainEventRegister() choose the right code paths.
Setting it to None is not enough, since calling domainEventRegiser() again
would trigger an TypeError.
Fix incorrect use of private data in remote driver
The remote driver is using the wrong privateData field in
a couple of functions. THis is harmless for stateful
drivers like QEMU/UML/LXC, but will crash with Xen
* src/remote/remote_driver.c: Fix use of privateData field
Set a stable & high MAC addr for guest TAP devices on host
A Linux software bridge will assume the MAC address of the enslaved
interface with the numerically lowest MAC addr. When the bridge
changes MAC address there is a period of network blackout, so a
change should be avoided. The kernel gives TAP devices a completely
random MAC address. Occassionally the random TAP device MAC is lower
than that of the physical interface (eth0, eth1etc) that is enslaved,
causing the bridge to change its MAC.
This change sets an explicit MAC address for all TAP devices created
using the configured MAC from the XML, but with the high byte set
to 0xFE. This should ensure TAP device MACs are higher than any
physical interface MAC.
* src/qemu/qemu_conf.c, src/uml/uml_conf.c: Pass in a MAC addr
for the TAP device with high byte set to 0xFE
* src/util/bridge.c, src/util/bridge.h: Set a MAC when creating
the TAP device to override random MAC
Laine Stump [Mon, 19 Jul 2010 23:52:57 +0000 (19:52 -0400)]
Remove erroneous setting of return value to errno.
One error exit in virStorageBackendCreateBlockFrom was setting the
return value to errno. The convention for volume build functions is to
return 0 on success or -1 on failure. Not only was it not necessary to
set the return value (it defaults to -1, and is set to 0 when
everything has been successfully completed), in the case that some
caller were checking for < 0 rather than != 0, they would incorrectly
believe that it completed successfully.
Laine Stump [Mon, 19 Jul 2010 23:48:59 +0000 (19:48 -0400)]
Change virDirCreate to return -errno on failure.
virDirCreate also previously returned 0 on success and errno on
failure. This makes it fit the recommended convention of returning 0
on success, -errno (ie a negative number) on failure.
Laine Stump [Mon, 19 Jul 2010 23:35:30 +0000 (19:35 -0400)]
Make virStorageBackendCopyToFD return -errno.
Previously virStorageBackendCopyToFD would simply return -1 on
error. This made the error return from one of its callers inconsistent
(createRawFileOpHook is supposed to return -errno, but if
virStorageBackendCopyToFD failed, createRawFileOpHook would just
return -1). Since there is a useful errno in every case of error
return from virStorageBackendCopyToFD, and since the other uses of
that function ignore the return code (beyond simply checking to see if
it is < 0), this is a safe change.
Laine Stump [Mon, 19 Jul 2010 23:25:58 +0000 (19:25 -0400)]
Change virFileOperation to return -errno (ie < 0) on error.
virFileOperation previously returned 0 on success, or the value of
errno on failure. Although there are other functions in libvirt that
use this convention, the preferred (and more common) convention is to
return 0 on success and -errno (or simply -1 in some cases) on
failure. This way the check for failure is always (ret < 0).
* src/util/util.c - change virFileOperation and virFileOperationNoFork to
return -errno on failure.
* src/storage/storage_backend.c, src/qemu/qemu_driver.c
- change the hook functions passed to virFileOperation to return
-errno on failure.
Re-arrange PCI device address assignment to match QEMU's default
To try and ensure that people upgrading from old QEMU get guests
with the same PCI device ordering, change the way we assign addrs
to match QEMU's default order. This should make Windows less
annoyed.
* src/qemu/qemu_conf.c: Follow QEMU's default PCI ordering
logic when assigning addresses
* tests/*.args: Update for changed PCI addresses
Explicitly represent balloon device in XML and handle PCI address
To allow compatibility with older QEMU PCI device slot assignment
it is necessary to explicitly track the balloon device in the
XML. This introduces a new device
<memballoon model='virtio|xen'/>
It can also have a PCI address, auto-assigned if necessary.
The memballoon will be automatically added to all Xen and QEMU
guests by default.
* docs/schemas/domain.rng: Add <memballoon> element
* src/conf/domain_conf.c, src/conf/domain_conf.h: parsing
and formatting for memballoon device. Always add a memory
balloon device to Xen/QEMU if none exists in XML
* src/libvirt_private.syms: Export memballoon model APIs
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Honour the
PCI device address in memory balloon device
* tests/*: Update to test new functionality
The first VGA and IDE devices need to have fixed PCI address
reservations. Currently this is handled inline with the other
non-primary VGA/IDE devices. The fixed virtio balloon device
at slot 3, ensures auto-assignment skips the slots 1/2. The
virtio address will shortly become configurable though. This
means the reservation of fixed slots needs to be done upfront
to ensure that they don't get re-used for other devices.
This is more or less reverting the previous changeset:
Fix restore of QEMU guests with PCI device reservation
The difference is that this time, instead of unconditionally
reserving the address, we only reserve the address if it was
initially type=none. Addresses of type=pci were handled
earlier in process by qemuDomainPCIAddressSetCreate(). This
ensures restore step doesn't have problems
* src/qemu/qemu_conf.c: Reserve first VGA + IDE address
upfront
The VIR_ERR_NO_SUPPORT refers to an API which is not implemented.
There is a separate VIR_ERR_CONFIG_UNSUPPORTED for XML config
options that are not available with the current hypervisor.
* src/qemu/qemu_conf.c, src/qemu/qemu_driver.c: Remove
many VIR_ERR_NO_SUPPORT replace with VIR_ERR_CONFIG_UNSUPPORTED
Chris Lalancette [Thu, 15 Jul 2010 14:12:35 +0000 (10:12 -0400)]
Fix a deadlock in bi-directional p2p concurrent migration.
If you try to execute two concurrent migrations p2p
from A->B and B->A, the two libvirtd's will deadlock
trying to perform the migrations. The reason for this is
that in p2p migration, the libvirtd's are responsible for
making the RPC Prepare, Migrate, and Finish calls. However,
they are currently holding the driver lock while doing so,
which basically guarantees deadlock in this scenario.
This patch fixes the situation by adding
qemuDomainObjEnterRemoteWithDriver and
qemuDomainObjExitRemoteWithDriver helper methods. The Enter
take an additional object reference, then drops both the
domain object lock and the driver lock. The Exit takes
both the driver and domain object lock, then drops the
reference. Adding calls to these Enter and Exit helpers
around remote calls in the various migration methods
seems to fix the problem for me in testing.
This should make the situation safe. The additional domain
object reference ensures that the domain object won't disappear
while this operation is happening. The BeginJob that is called
inside of qemudDomainMigratePerform ensures that we can't execute a
second migrate (or shutdown, or save, etc) job while the
migration is active. Finally, the additional check on the state
of the vm after we reacquire the locks ensures that we can't
be surprised by an external event (domain crash, etc).
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Chris Lalancette [Tue, 30 Mar 2010 13:03:26 +0000 (09:03 -0400)]
Make virsh setmaxmem balloon only when successful.
After playing around with virsh setmaxmem for a bit,
I ran into some surprising behavior; if a hypervisor does
not support the virDomainSetMaxMemory() API, but the value
specified for setmaxmem is less than the current amount
of memory in the domain, the domain would be ballooned
down *before* an error was reported.
To make this more consistent, run virDomainSetMaxMemory()
before trying to shrink; that way, if an error is thrown,
no changes to the running domain are made.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Chris Lalancette [Thu, 17 Jun 2010 19:36:36 +0000 (15:36 -0400)]
Use unsigned long in cmdSetmem.
The virsh command "setmem" takes as input a number that
should represent an unsigned long number of kilobytes. Fix
cmdSetmem to properly parse this as an unsigned long instead
of an int.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Laine Stump [Mon, 19 Jul 2010 22:59:07 +0000 (18:59 -0400)]
fsync new storage volumes even if new volume was copied.
Originally the storage volume files were opened with O_DSYNC to make
sure they were flushed to disk immediately. It turned out that this
was extremely slow in some cases, so the O_DSYNC was removed in favor
of just calling fsync() after all the data had been written. However,
this call to fsync was inside the block that is executed to zero-fill
the end of the volume file. In cases where the new volume is copied
from an old volume, and they are the same length, this fsync would
never take place.
Now the fsync is *always* done, unless there is an error (in which
case it isn't important, and is most likely inappropriate.
Laine Stump [Mon, 19 Jul 2010 22:53:38 +0000 (18:53 -0400)]
Don't skip zero'ing end of volume file when inputvol is shorter than newvol
A missing set of braces around an error condition caused us to skip
zero'ing out the remainder of a new volume file if the new volume was
longer than the original (the goto was supposed to be taken only in
the case of error, but was always being taken).
Chris Lalancette [Thu, 17 Jun 2010 18:58:55 +0000 (14:58 -0400)]
Fix up inconsistent virsh option error reporting.
The virsh option error reporting was not being used
consistently; some commands would spit out errors on
missing required options while others would just silently fail.
However, vshCommandOptString knows which ones are required
and which ones aren't, so make it spit out an error where
appropriate. The rest of the patch is just cleaning up
the uses of vshCommandOptString to deal with the new error
reporting.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Use the extract backing store format in storage volume lookup
The storage volume lookup code was probing for the backing store
format, instead of using the format extracted from the file
itself. This meant it could report in accurate information. If
a format is included in the file, then use that in preference,
with probing as a fallback.
* src/storage/storage_backend_fs.c: Use extracted backing store
format
When creating qcow2 files with a backing store, it is important
to set an explicit format to prevent QEMU probing. The storage
backend was only doing this if it found a 'kvm-img' binary. This
is wrong because plenty of kvm-img binaries don't support an
explicit format, and plenty of 'qemu-img' binaries do support
a format. The result was that most qcow2 files were not getting
a backing store format.
This patch runs 'qemu-img -h' to check for the two support
argument formats
'-o backing_format=raw'
'-F raw'
and use whichever option it finds
* src/storage/storage_backend.c: Query binary to determine
how to set the backing store format
Add ability to set a default driver name/type when parsing disks
Record a default driver name/type in capabilities struct. Use this
when parsing disks if value is not set in XML config.
* src/conf/capabilities.h: Record default driver name/type for disks
* src/conf/domain_conf.c: Fallback to default driver name/type
when parsing disks
* src/qemu/qemu_driver.c: Set default driver name/type to raw
Disable all disk probing in QEMU driver & add config option to re-enable
Disk format probing is now disabled by default. A new config
option in /etc/qemu/qemu.conf will re-enable it for existing
deployments where this causes trouble
Pass security driver object into all security driver callbacks
The implementation of security driver callbacks often needs
to access the security driver object. Currently only a handful
of callbacks include the driver object as a parameter. Later
patches require this is many more places.
* src/qemu/qemu_driver.c: Pass in the security driver object
to all callbacks
* src/qemu/qemu_security_dac.c, src/qemu/qemu_security_stacked.c,
src/security/security_apparmor.c, src/security/security_driver.h,
src/security/security_selinux.c: Add a virSecurityDriverPtr
param to all security callbacks
Convert all disk backing store loops to shared helper API
Update the QEMU cgroups code, QEMU DAC security driver, SELinux
and AppArmour security drivers over to use the shared helper API
virDomainDiskDefForeachPath().
* src/qemu/qemu_driver.c, src/qemu/qemu_security_dac.c,
src/security/security_selinux.c, src/security/virt-aa-helper.c:
Convert over to use virDomainDiskDefForeachPath()
There is duplicated code which iterates over disk backing stores
performing some action. Provide a convenient helper for doing
this to eliminate duplication & risk of mistakes with disk format
probing
Require format to be passed into virStorageFileGetMetadata
Require the disk image to be passed into virStorageFileGetMetadata.
If this is set to VIR_STORAGE_FILE_AUTO, then the format will be
resolved using probing. This makes it easier to control when
probing will be used
* src/qemu/qemu_driver.c, src/qemu/qemu_security_dac.c,
src/security/security_selinux.c, src/security/virt-aa-helper.c:
Set VIR_STORAGE_FILE_AUTO when calling virStorageFileGetMetadata.
* src/storage/storage_backend_fs.c: Probe for disk format before
calling virStorageFileGetMetadata.
* src/util/storage_file.h, src/util/storage_file.c: Remove format
from virStorageFileMeta struct & require it to be passed into
method.
Refactor virStorageFileGetMetadataFromFD to separate functionality
The virStorageFileGetMetadataFromFD did two jobs in one. First
it probed for storage type, then it extracted metadata for the
type. It is desirable to be able to separate these jobs, allowing
probing without querying metadata, and querying metadata without
probing.
To prepare for this, split out probing code into a new pair of
methods
Instead of including a field in FileTypeInfo struct for the
disk format, rely on the array index matching the format.
Use verify() to assert the correct number of elements in the
array.
* src/util/storage_file.c: remove type field from FileTypeInfo
Extract the backing store format as well as name, if available
When QEMU opens a backing store for a QCow2 file, it will
normally auto-probe for the format of the backing store,
rather than assuming it has the same format as the referencing
file. There is a QCow2 extension that allows an explicit format
for the backing store to be embedded in the referencing file.
This closes the auto-probing security hole in QEMU.
This backing store format can be useful for libvirt users
of virStorageFileGetMetadata, so extract this data and report
it.
QEMU does not require disk image backing store files to be in
the same format the file linkee. It will auto-probe the disk
format for the backing store when opening it. If the backing
store was intended to be a raw file this could be a security
hole, because a guest may have written data into its disk that
then makes the backing store look like a qcow2 file. If it can
trick QEMU into thinking the raw file is a qcow2 file, it can
access arbitrary files on the host by adding further backing
store links.
To address this, callers of virStorageFileGetMeta need to be
told of the backing store format. If no format is declared,
they can make a decision whether to allow format probing or
not.
CVE-2010-2242 Apply a source port mapping to virtual network masquerading
IPtables will seek to preserve the source port unchanged when
doing masquerading, if possible. NFS has a pseudo-security
option where it checks for the source port <= 1023 before
allowing a mount request. If an admin has used this to make the
host OS trusted for mounts, the default iptables behaviour will
potentially allow NAT'd guests access too. This needs to be
stopped.
With this change, the iptables -t nat -L -n -v rules for the
default network will be
* src/network/bridge_driver.c: Add masquerade rules for TCP
and UDP protocols
* src/util/iptables.c, src/util/iptables.c: Add source port
mappings for TCP & UDP protocols when masquerading.
man pages: update authors and copyright notice for libvirtd and virsh
This patch removes the individual author names from the libvirtd and virsh
man pages, instead referring to the main AUTHORS file distributed with
libvirt. This approach is needed, as we can't guarantee unicode support
across all versions of pod2man used with libvirt.
Additionally, this patch includes the libvirtd man page in the spec file
used with "make rpm". Without this patch "make rpm" is broken.
The universe of possible conventions isn't clear. Rather than trying
to understand all possible conventions, this patch divides devices
into two groups, device mapper devices and everything else. Device
mapper devices seem always to follow the convention of device ->
devicep1; everything else is canonicalized.
daemon: dispatch.c should include stdio.h (and stdarg.h)
dispatch.c requires stdio.h (and stdarg.h), however, currently
dispatch.c implicitly relys on rpc/xdr.h to include stdio.h.
If rpc/xdr.h unxpectedly does not include stdio.h, the compilation
of dispatch.c fails.
This can happen, for example, when portablexdr is installed
under /usr/local; because portablexdr's rpc/xdr.h does not
include stdio.h and gcc looks up it not /usr/include/rpc/xdr.h.
Note that stdarg.h is also included according to man va_start,
although stdio.h seems including it anyway.
Jim Meyering [Tue, 13 Jul 2010 20:28:35 +0000 (15:28 -0500)]
uml_driver: correct logic error in umlMonitorCommand
* src/uml/uml_driver.c (umlMonitorCommand): Correct flaw that would
cause unconditional "incomplete reply ..." failure, since "nbytes"
was always 0 or 1.
Jim Meyering [Tue, 13 Jul 2010 20:15:04 +0000 (15:15 -0500)]
qemuConnectMonitor: fix a bug that would have masked SELinux failure
* src/qemu/qemu_driver.c (qemuConnectMonitor): Correct erroneous
parenthesization in two expressions. Without this fix, failure
to set or clear SELinux security context in the monitor would go
undiagnosed. Also correct a diagnostic and split some long lines.
projects / libvirt.git / log