Those regulators are not actually supported by the AB8500 regulator
driver. There is no ab8500_regulator_info for them and no entry in
ab8505_regulator_match.
As such, they cannot be registered successfully, and looking them
up in ab8505_regulator_match causes an out-of-bounds array read.
Fixes: 547f384f33db ("regulator: ab8500: add support for ab8505") Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20191106173125.14496-2-stephan@gerhold.net Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the latest reference manual Rev.0,06/2019, the DDR clock mux
is extended to 2 bits, and the clock options are also changed,
correct them accordingly.
The original --reltime patch forbid --time with --reltime.
But it turns out --time doesn't really care about --reltime, because the
relative time is only used at final output, while the time filtering
always works earlier on absolute time.
So just remove the check and allow combining the two options.
Fixes: 90b10f47c0ee ("perf script: Support relative time") Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Link: http://lore.kernel.org/lkml/20191002164642.1719-1-andi@firstfloor.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since there are some DIE which has only ranges instead of the
combination of entrypc/highpc, address verification must use
dwarf_haspc() instead of dwarf_entrypc/dwarf_highpc.
Also, the ranges only DIE will have a partial code in different section
(e.g. unlikely code will be in text.unlikely as "FUNC.cold" symbol). In
that case, we can not use dwarf_entrypc() or die_entrypc(), because the
offset from original DIE can be a minus value.
Instead, this simply gets the symbol and offset from symtab.
Without this patch;
# perf probe -D clear_tasks_mm_cpumask:1
Failed to get entry address of clear_tasks_mm_cpumask
Error: Failed to add events.
The level of cckpd is from 0 to 4, and it is the index of
array pd_lvl[] and cs_lvl[]. However, the length of both arrays
are 4, which is smaller than the possible maximum input index.
Enumerate cck level to make sure the max level will not be wrong
if new level is added in future.
Many of the sgl-per-hdwq paths are locking with spin_lock_irq() and
spin_unlock_irq() and may unwittingly raising irq when it shouldn't. Hard
deadlocks were seen around lpfc_scsi_prep_cmnd().
Fix by converting the locks to irqsave/irqrestore.
Fixes: d79c9e9d4b3d ("scsi: lpfc: Support dynamic unbounded SGL lists on G7 hardware.") Link: https://lore.kernel.org/r/20190922035906.10977-16-jsmart2021@gmail.com Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In lpfc_release_io_buf, an lpfc_io_buf is returned to the 'available' pool
before any associated sgl or cmd and rsp buffers are returned via their
respective 'put' routines. If xri rebalancing occurs and an lpfc_io_buf
structure is reused quickly, there may be a race condition between release
of old and association of new resources.
Re-ordered lpfc_release_io_buf to release sgl and cmd/rsp
buffer lists before releasing the lpfc_io_buf structure for re-use.
Fixes: d79c9e9d4b3d ("scsi: lpfc: Support dynamic unbounded SGL lists on G7 hardware.") Link: https://lore.kernel.org/r/20190922035906.10977-17-jsmart2021@gmail.com Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an unintended sign extension on left shifts. From Colin
King: "Shifting a u8 left will cause the value to be promoted to an
integer. If the top bit of the u8 is set then the following conversion to
an u64 will sign extend the value causing the upper 32 bits to be set in
the result."
Fix this by using get_unaligned_be*() instead.
Fixes: bf8162354233 ("[SCSI] add scsi trace core functions and put trace points") Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.com> Cc: Douglas Gilbert <dgilbert@interlog.com> Link: https://lore.kernel.org/r/20191101211447.187151-1-bvanassche@acm.org Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In qla2x00_find_all_fabric_devs(), fcport->flags & FCF_LOGIN_NEEDED is a
necessary condition for logging into new rports, but not for dropping lost
ones.
Fixes: 726b85487067 ("qla2xxx: Add framework for async fabric discovery") Link: https://lore.kernel.org/r/20191122221912.20100-2-martin.wilck@suse.com Tested-by: David Bond <dbond@suse.com> Signed-off-by: Martin Wilck <mwilck@suse.com> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4fa183455988 ("scsi: qla2xxx: Utilize pci_alloc_irq_vectors/
pci_free_irq_vectors calls.") use pci_alloc_irq_vectors() to replace
pci_enable_msi() but it didn't handle the return value correctly. This bug
make qla2x00 always fail to setup MSI if MSI-X fail, so fix it.
BTW, improve the log message of return value in qla2x00_request_irqs() to
avoid confusion.
Fixes: 4fa183455988 ("scsi: qla2xxx: Utilize pci_alloc_irq_vectors/pci_free_irq_vectors calls.") Cc: Michael Hernandez <michael.hernandez@cavium.com> Link: https://lore.kernel.org/r/1574314847-14280-1-git-send-email-chenhc@lemote.com Signed-off-by: Huacai Chen <chenhc@lemote.com> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that we don't clean up the request queue fully for bsg
devices, as the blk mq tags for the request queue are not freed.
Fix by doing the queue removal in one place - in sas_rphy_remove() -
instead of unregistering the queue in sas_rphy_remove() and finally
cleaning up the queue in calling blk_cleanup_queue() from
sas_end_device_release() or sas_expander_release().
Function bsg_remove_queue() can handle a NULL pointer q, so remove the
precheck in sas_rphy_remove().
Fixes: 651a013649943 ("scsi: scsi_transport_sas: switch to bsg-lib for SMP passthrough") Link: https://lore.kernel.org/r/1574242755-94156-1-git-send-email-john.garry@huawei.com Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 73a4925d154c ("scsi: hisi_sas: Update all the registers after suspend and resume") Link: https://lore.kernel.org/r/1573551059-107873-3-git-send-email-john.garry@huawei.com Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Print the string for which conversion failed instead of printing the
function name twice.
Fixes: 2650d71e244f ("target: move transport ID handling to the core") Cc: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20191107215525.64415-1-bvanassche@acm.org Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The member hba->pcidev may be used after its reference is dropped. Move the
put function to where it is never used to avoid potential use after free
issues.
Fixes: a77171806515 ("[SCSI] bnx2i: Removed the reference to the netdev->base_addr") Link: https://lore.kernel.org/r/1573043541-19126-1-git-send-email-bianpan2016@163.com Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable init_fw_cb is released twice, resulting in a double free
bug. The call to the function dma_free_coherent() before goto is removed to
get rid of potential double free.
Fixes: 2a49a78ed3c8 ("[SCSI] qla4xxx: added IPv6 support.") Link: https://lore.kernel.org/r/1572945927-27796-1-git-send-email-bianpan2016@163.com Signed-off-by: Pan Bian <bianpan2016@163.com> Acked-by: Manish Rangankar <mrangankar@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If set the BIST init value after enabling BIST, there may be still some few
error bits. According to the process, need to set the BIST init value
before enabling BIST.
Fixes: 97b151e75861 ("scsi: hisi_sas: Add BIST support for phy loopback") Link: https://lore.kernel.org/r/1571926105-74636-3-git-send-email-john.garry@huawei.com Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to a merge error, we attempt to create 2x debugfs dump folders, which
fails:
[ 861.101914] debugfs: Directory 'dump' with parent '0000:74:02.0'
already present!
This breaks the dump function.
To fix, remove the superfluous attempt to create the folder.
Fixes: 7ec7082c57ec ("scsi: hisi_sas: Add hisi_sas_debugfs_alloc() to centralise allocation") Link: https://lore.kernel.org/r/1571926105-74636-2-git-send-email-john.garry@huawei.com Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 60e4cf67a58 (reiserfs: fix extended attributes on the root
directory) introduced a regression open_xa_root started returning
-EOPNOTSUPP but it was not handled properly in reiserfs_for_each_xattr.
When the reiserfs module is built without CONFIG_REISERFS_FS_XATTR,
deleting an inode would result in a warning and chowning an inode
would also result in a warning and then fail to complete.
With CONFIG_REISERFS_FS_XATTR enabled, the xattr root would always be
present for read-write operations.
This commit handles -EOPNOSUPP in the same way -ENODATA is handled.
Fixes: 60e4cf67a582 ("reiserfs: fix extended attributes on the root directory") CC: stable@vger.kernel.org # Commit 60e4cf67a58 was picked up by stable Link: https://lore.kernel.org/r/20200115180059.6935-1-jeffm@suse.com Reported-by: Michael Brunnbauer <brunni@netestate.de> Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver *can* be a module, but then its parameters (socket path)
are untrusted data from inside the VM, and that isn't allowed. Allow
the code to only be built-in to avoid that.
Fixes: 5d38f324993f ("um: drivers: Add virtio vhost-user driver") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Anton Ivanov <anton.ivanov@cambridgegreys.co.uk> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the main() code, we eventually enable signals just before
exec() or exit(), in order to to not have signals pending and
delivered *after* the exec().
I've observed SIGSEGV loops at this point, and the reason seems
to be the irqflags tracing; this makes sense as the kernel is
no longer really functional at this point. Since there's really
no reason to use unblock_signals_trace() here (I had just done
a global search & replace), use the plain unblock_signals() in
this case to avoid going into the no longer functional kernel.
Fixes: 0dafcbe128d2 ("um: Implement TRACE_IRQFLAGS_SUPPORT") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 4844ef80305d ("mtd: cfi_cmdset_0002: Add support for polling
status register") added checking for the status register error bits into
chip_good() to only return 1 if these bits are 0s. Unfortunately, this
means that polling using chip_good() always reaches a timeout condition
when erase or program failure bits are set. Let's fully delegate the task
of determining the error conditions to cfi_check_err_status() and make
chip_good() only look for the Device Ready/Busy condition.
Fixes: 4844ef80305d ("mtd: cfi_cmdset_0002: Add support for polling status register") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cypress S26K{L|S}P{128|256|512}S datasheet says that the error bits in
the status register are only valid when the "device ready" bit 7 is set.
Add the check for the device ready bit in cfi_check_err_status() as that
function isn't always called with this bit set.
Fixes: 4844ef80305d ("mtd: cfi_cmdset_0002: Add support for polling status register") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the use of sizeof(), command size set for the spi transfer
was wrong. Driver was sending and receiving always 1 byte less
and especially on write, it was hanging.
echo -n -e "\\x1\\x2\\x3\\x4" > /dev/mtd1
And read part too now works as expected.
hexdump -C -n16 /dev/mtd1 00000000 01 02 03 04 ab f3 ad c2 ab e3 f4 36 dd 38 04 15 00000010
Fixes: 4379075a870b ("mtd: mchp23k256: Add support for mchp23lcv1024") Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 951d48855d86 ("of: Make of_dma_get_range() work on bus nodes")
reworked the logic such that of_dma_get_range() works correctly
starting from a bus node containing "dma-ranges".
Since on Juno we don't have a SoC level bus node and "dma-ranges" is
present only in the root node, we get the following error:
OF: translation of DMA address(0) to CPU address failed node(/sram@2e000000)
OF: translation of DMA address(0) to CPU address failed node(/uart@7ff80000)
...
OF: translation of DMA address(0) to CPU address failed node(/mhu@2b1f0000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
OF: translation of DMA address(0) to CPU address failed node(/iommu@2b600000)
So let's fix it by dropping the "dma-ranges" property for now. This
should be fine since it doesn't represent any kind of device-visible
restriction; it was only there for completeness, and we've since given
in to the assumption that missing "dma-ranges" implies a 1:1 mapping
anyway.
We can add it later with a proper SoC bus node and moving all the
devices that belong there along with the "dma-ranges" if required.
Looks like we've had the sgx sysconfig register and revision register
always wrong for omap4, including the old platform data. Let's fix the
offsets to what the TRM says. Otherwise the sgx module may never idle
depending on the state of the real sysconfig register.
Fixes: d23a163ebe5a ("ARM: dts: Add nodes for missing omap4 interconnect target modules") Cc: H. Nikolaus Schaller <hns@goldelico.com> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Older versions of the Juno *SoC* TRM [1] recommended that the UART clock
source should be 7.2738 MHz, whereas the *system* TRM [2] stated a more
correct value of 7.3728 MHz. Somehow the wrong value managed to end up in
our DT.
Doing a prime factorisation, a modulo divide by 115200 and trying
to buy a 7.2738 MHz crystal at your favourite electronics dealer suggest
that the old value was actually a typo. The actual UART clock is driven
by a PLL, configured via a parameter in some board.txt file in the
firmware, which reads 7.37 MHz (sic!).
Fix this to correct the baud rate divisor calculation on the Juno board.
The DRA7 CPSW MDIO functional clock (gmac_clkctrl DRA7_GMAC_GMAC_CLKCTRL 0)
is specified incorrectly, which is caused incorrect MDIO bus clock
configuration MDCLK. The correct CPSW MDIO functional clock is
gmac_main_clk (125MHz), which is the same as CPSW fck. Hence fix it.
Fixes: 1faa415c9c6e ("ARM: dts: Add fck for cpsw mdio for omap variants") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As it was found recently, the Performance Monitoring Unit (PMU) on the
Allwinner A64 SoC was not generating (the right) interrupts. With the
SPI numbers from the manual the kernel did not receive any overflow
interrupts, so perf was not happy at all.
It turns out that the numbers were just off by 4, so the PMU interrupts
are from 148 to 151, not from 152 to 155 as the manual describes.
This was found by playing around with U-Boot, which typically does not
use interrupts, so the GIC is fully available for experimentation:
With *every* PPI and SPI enabled, an overflowing PMU cycle counter was
found to set a bit in one of the GICD_ISPENDR registers, with careful
counting this was determined to be number 148.
Tested with perf record and perf top on a Pine64-LTS. Also tested with
tasksetting to every core to confirm the assignment between IRQs and
cores.
This somewhat "revert-fixes" commit ed3e9406bcbc ("arm64: dts: allwinner:
a64: Drop PMU node").
Fixes: 34a97fcc71c2 ("arm64: dts: allwinner: a64: Add PMU node") Fixes: ed3e9406bcbc ("arm64: dts: allwinner: a64: Drop PMU node") Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The snvs-poweroff driver can power off the system by pulling the
PMIC_ON_REQ signal low, to let the PMIC disable the power.
The Kontron SoMs do not have this signal connected, so let's remove
the node.
This fixes a real issue when the signal is asserted at poweroff,
but not actually causing the power to turn off. It was observed,
that in this case the system would not shut down properly.
This is unused on cheza. Delete the node to get ride of the reserved-
memory section, and to avoid the driver from attempting to load a zap
shader that doesn't exist every time it powers up the GPU.
This also avoids a massive amount of dmesg spam about missing zap fw:
msm ae00000.mdss: [drm:adreno_request_fw] *ERROR* failed to load
qcom/a630_zap.mdt: -2
adreno 5000000.gpu: [drm:adreno_zap_shader_load] *ERROR* Unable to
load a630_zap.mdt
Signed-off-by: Rob Clark <robdclark@chromium.org> Cc: Douglas Anderson <dianders@chromium.org> Fixes: 3fdeaee951aa ("arm64: dts: sdm845: Add zap shader region for GPU") Reviewed-by: Douglas Anderson <dianders@chromium.org> Tested-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Andy Gross <agross@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.0-rc7+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Use READ_ONCE() and WRITE_ONCE() to annotate this expected race.
Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20191205045619.204946-1-edumazet@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arch/arm/dts/meson-gxl-s905x-khadas-vim.dtb: Warning (avoid_unnecessary_addr_size):
/gpio-keys-polled: unnecessary #address-cells/#size-cells
without "ranges" or child "reg" property
Fixes: e15d2774b8c0 ("ARM64: dts: meson-gxl: add support for the Khadas VIM board") Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "priv->hw_type" is an enum and in this context GCC will treat it
as an unsigned int so the error handling will never trigger.
Fixes: a910e4a94f69 ("cw1200: add driver for the ST-E CW1100 & CW1200 WLAN chipsets") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Boot failure has been reported on MSM8998 based laptop when
coresight is enabled. This is most likely due to lack of
firmware support for coresight on production device when
compared to debug device like MTP where this issue is not
observed. So disable coresight by default for MSM8998 and
enable it only for MSM8998 MTP.
At the time commit ce5ec440994b ("tcp: ensure epoll edge trigger
wakeup when write queue is empty") was added to the kernel,
we still had a single write queue, combining rtx and write queues.
Once we moved the rtx queue into a separate rb-tree, testing
if sk_write_queue is empty has been suboptimal.
Indeed, if we have packets in the rtx queue, we probably want
to delay the EPOLLOUT generation at the time incoming packets
will free them, making room, but more importantly avoiding
flooding application with EPOLLOUT events.
Solution is to use tcp_rtx_and_write_queues_empty() helper.
Fixes: 75c119afe14f ("tcp: implement rb-tree based retransmit queue") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jason Baron <jbaron@akamai.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DT property definitions must be under a 'properties' keyword. This was
missing for 'snps,tso' in an if/then clause. A meta-schema fix will
catch future errors like this.
Fixes: 7db3545aef5f ("dt-bindings: net: stmmac: Convert the binding to a schemas") Cc: "David S. Miller" <davem@davemloft.net> Acked-by: Maxime Ripard <mripard@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
../drivers/block/xen-blkfront.c:1117:4: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
nr_parts = PARTS_PER_DISK;
^
../drivers/block/xen-blkfront.c:1115:3: note: previous statement is here
if (err)
^
This is because there is a space at the beginning of this line; remove
it so that the indentation is consistent according to the Linux kernel
coding style and clang no longer warns.
While we are here, the previous line has some trailing whitespace; clean
that up as well.
Fixes: c80a420995e7 ("xen-blkfront: handle Xen major numbers other than XENVBD") Link: https://github.com/ClangBuiltLinux/linux/issues/791 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Juergen Gross <jgross@suse.com> Acked-by: Roger Pau Monné <roger.pau@citrix.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit cited below causes devlink to emit a warning if a type was
not set on a devlink port for longer than 30 seconds to "prevent
misbehavior of drivers". This proved to be problematic when
unregistering the backing netdev. The flow is always:
devlink_port_type_clear() // schedules the warning
unregister_netdev() // blocking
devlink_port_unregister() // cancels the warning
The call to unregister_netdev() can block for long periods of time for
various reasons: RTNL lock is contended, large amounts of configuration
to unroll following dismantle of the netdev, etc. This results in
devlink emitting a warning despite the driver behaving correctly.
In emulated environments (of future hardware) which are usually very
slow, the warning can also be emitted during port creation as more than
30 seconds can pass between the time the devlink port is registered and
when its type is set.
In addition, syzbot has hit this warning [1] 1974 times since 07/11/19
without being able to produce a reproducer. Probably because
reproduction depends on the load or other bugs (e.g., RTNL not being
released).
To prevent bogus warnings, increase the timeout to 1 hour.
Fixes: 136bf27fc0e9 ("devlink: add warning in case driver does not set port type") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: syzbot+b0a18ed7b08b735d2f41@syzkaller.appspotmail.com Reported-by: Alex Veber <alexve@mellanox.com> Tested-by: Alex Veber <alexve@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RSS, when enabled, will bypass the L3 and L4 filtering causing it not
to work. Add a check before trying to setup the filters.
Fixes: 425eabddaf0f ("net: stmmac: Implement L3/L4 Filters using TC Flower") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are disabling RSS on HW but not updating the internal private status
to the 'disabled' state. This is needed for next tc commit that will
check if RSS is disabled before trying to apply filters.
Fixes: 4647e021193d ("net: stmmac: selftests: Add selftest for L3/L4 Filters") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mausezahn does not recognize "own" as a keyword on source IP address. As a
result, the MC stream is not running at all, and therefore no UC
degradation can be observed even in principle.
Fix the invocation, and tighten the test: due to the minimum shaper
configured at the MC TCs, we always expect about 20% degradation. Fail the
test if it is lower.
Fixes: 573363a68f27 ("selftests: mlxsw: Add qos_lib.sh") Signed-off-by: Petr Machata <petrm@mellanox.com> Reported-by: Amit Cohen <amitc@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the VLAN ID does not match the expected one it means filter failed
in HW. Fix it.
Fixes: 94e18382003c ("net: stmmac: selftests: Add selftest for VLAN TX Offload") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Synopsys AXS101 boards do not support unaligned memory loads or stores.
Change the selftests mechanism to explicity:
- Not add extra alignment in TX SKB
- Use the unaligned version of ether_addr_equal()
Fixes: 091810dbded9 ("net: stmmac: Introduce selftests support") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mlxsw configures Spectrum in such a way that BUM traffic is passed not
through its nominal traffic class TC, but through its MC counterpart TC+8.
However, when collecting statistics, Qdiscs only look at the nominal TC and
ignore the MC TC.
Add two helpers to compute the value for logical TC from the constituents,
one for backlog, the other for tail drops. Use them throughout instead of
going through the xstats pointer directly.
Counters for TX bytes and packets are deduced from packet priority
counters, and therefore already include BUM traffic. wred_drop counter is
irrelevant on MC TCs, because RED is not enabled on them.
Fixes: 7b8195306694 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports") Signed-off-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per-port counter cache used by Qdiscs is updated periodically, unless the
port is down. The fact that the cache is not updated for down ports is no
problem for most counters, which are relative in nature. However, backlog
is absolute in nature, and if there is a non-zero value in the cache around
the time that the port goes down, that value just stays there. This value
then leaks to offloaded Qdiscs that report non-zero backlog even if
there (obviously) is no traffic.
The HW does not keep backlog of a downed port, so do likewise: as the port
goes down, wipe the backlog value from xstats.
Fixes: 075ab8adaf4e ("mlxsw: spectrum: Collect tclass related stats periodically") Signed-off-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver needs to prepend a Tx header to each packet it is
transmitting. The header includes information such as the egress port
and traffic class.
The addition of the header requires the driver to modify the SKB's
header and therefore it must not be shared. Otherwise, we risk hitting
various race conditions.
For example, when a packet is flooded (cloned) by the bridge driver to
two switch ports swp1 and swp2:
t0 - mlxsw_sp_port_xmit() is called for swp1. Tx header is prepended with
swp1's port number
t1 - mlxsw_sp_port_xmit() is called for swp2. Tx header is prepended with
swp2's port number, overwriting swp1's port number
t2 - The device processes data buffer from t0. Packet is transmitted via
swp2
t3 - The device processes data buffer from t1. Packet is transmitted via
swp2
Usually, the device is fast enough and transmits the packet before its
Tx header is overwritten, but this is not the case in emulated
environments.
Fix this by making sure the SKB's header is writable by calling
skb_cow_head(). Since the function ensures we have headroom to push the
Tx header, the check further in the function can be removed.
v2:
* Use skb_cow_head() instead of skb_unshare() as suggested by Jakub
* Remove unnecessary check regarding headroom
Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Shalom Toledo <shalomt@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When adding the sh_eth_cpu_data::dual_port flag I forgot to add the flag
checks to __sh_eth_get_regs(), causing the non-existing TSU registers to
be dumped by 'ethtool' on the single port Ether controllers having TSU...
Fixes: a94cf2a614f8 ("sh_eth: fix TSU init on SH7734/R8A7740") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It will cause modprobe atombios stuck problem in raven2 if it doesn't
allow direct upload save restore list from gfx driver.
So it needs to allow direct upload save restore list for raven2
temporarily.
With the implementation of the system reset controller we lost a setting
that is currently applied by the bootloader and which configures the IMP
port for 2Gb/sec, the default is 1Gb/sec. This is needed given the
number of ports and applications we expect to run so bring back that
setting.
Fixes: 01b0ac07589e ("net: dsa: bcm_sf2: Add support for optional reset controller line") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The correct name is GSWIP (Gigabit Switch IP). Typo was introduced in 875138f81d71a ("dsa: Move tagger name into its ops structure") while
moving tagger names to their structures.
Fixes: 875138f81d71a ("dsa: Move tagger name into its ops structure") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexander Lobakin <alobakin@dlink.ru> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sja1105_parse_ports_node function was tested only on device trees
where all ports were enabled. Fix this check so that the driver
continues to probe only with the ports where status is not "disabled",
as expected.
Fixes: 8aa9ebccae87 ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We would not be transmitting using the correct SYSTEMPORT transmit queue
during ndo_select_queue() which looks up the internal TX ring map
because while establishing the mapping we would be off by 4, so for
instance, when we populate switch port mappings we would be doing:
switch port 0, queue 0 -> ring index #0
switch port 0, queue 1 -> ring index #1
...
switch port 0, queue 3 -> ring index #3
switch port 1, queue 0 -> ring index #8 (4 + 4 * 1)
...
instead of using ring index #4. This would cause our ndo_select_queue()
to use the fallback queue mechanism which would pick up an incorrect
ring for that switch port. Fix this by using the correct switch queue
number instead of SYSTEMPORT queue number.
Fixes: 25c440704661 ("net: systemport: Simplify queue mapping logic") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building with PROVE_LOCKING=y, lockdep shows the following
dump message.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
...
Calling device_set_wakeup_enable() directly occurs this issue,
and it isn't necessary for initialization, so this patch creates
internal function __ave_ethtool_set_wol() and replaces with this
in ave_init() and ave_resume().
Fixes: 7200f2e3c9e2 ("net: ethernet: ave: Set initial wol state to disabled") Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DSN read can fail, for example on a kdump kernel without PCIe extended
config space support. If DSN read fails, don't set the
BNXT_FLAG_DSN_VALID flag and continue loading. Check the flag
to see if the stored DSN is valid before using it. Only VF reps
creation should fail without valid DSN.
Fixes: 03213a996531 ("bnxt: move bp->switch_id initialization to PF probe") Reported-by: Marc Smith <msmith626@gmail.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix bnxt_fltr_match() to match ipv6 source and destination addresses.
The function currently only checks ipv4 addresses and will not work
corrently on ipv6 filters.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NTUPLE related firmware commands are sent to the wrong firmware
channel, causing all these commands to fail on new firmware that
supports the new firmware channel. Fix it by excluding the 3
NTUPLE firmware commands from the list for the new firmware channel.
Fixes: 760b6d33410c ("bnxt_en: Add support for 2nd firmware message channel.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the packet pointed to by retransmit_skb_hint is unlinked by ACK,
retransmit_skb_hint will be set to NULL in tcp_clean_rtx_queue().
If packet loss is detected at this time, retransmit_skb_hint will be set
to point to the current packet loss in tcp_verify_retransmit_hint(),
then the packets that were previously marked lost but not retransmitted
due to the restriction of cwnd will be skipped and cannot be
retransmitted.
To fix this, when retransmit_skb_hint is NULL, retransmit_skb_hint can
be reset only after all marked lost packets are retransmitted
(retrans_out >= lost_out), otherwise we need to traverse from
tcp_rtx_queue_head in tcp_xmit_retransmit_queue().
Packetdrill to demonstrate:
// Disable RACK and set max_reordering to keep things simple
0 `sysctl -q net.ipv4.tcp_recovery=0`
+0 `sysctl -q net.ipv4.tcp_max_reordering=3`
// Send 8 data segments
+0 write(4, ..., 8000) = 8000
+0 > P. 1:8001(8000) ack 1
// Enter recovery and 1:3001 is marked lost
+.01 < . 1:1(0) ack 1 win 257 <sack 3001:4001,nop,nop>
+0 < . 1:1(0) ack 1 win 257 <sack 5001:6001 3001:4001,nop,nop>
+0 < . 1:1(0) ack 1 win 257 <sack 5001:7001 3001:4001,nop,nop>
// Retransmit 1:1001, now retransmit_skb_hint points to 1001:2001
+0 > . 1:1001(1000) ack 1
// 1001:2001 was ACKed causing retransmit_skb_hint to be set to NULL
+.01 < . 1:1(0) ack 2001 win 257 <sack 5001:8001 3001:4001,nop,nop>
// Now retransmit_skb_hint points to 4001:5001 which is now marked lost
// BUG: 2001:3001 was not retransmitted
+0 > . 2001:3001(1000) ack 1
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com> Acked-by: Neal Cardwell <ncardwell@google.com> Tested-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing endpoint sanity check to probe in order to prevent a
NULL-pointer dereference (or slab out-of-bounds access) when retrieving
the interrupt-endpoint bInterval on ndo_open() in case a device lacks
the expected endpoints.
Fixes: 40a82917b1d3 ("net/usb/r8152: enable interrupt transfer") Cc: hayeswang <hayeswang@realtek.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a bug in ptp_clock_unregister(), where ptp_cleanup_pin_groups()
first frees ptp->pin_{,dev_}attr, but then posix_clock_unregister() needs
them to destroy a related sysfs device.
These functions can not be just swapped, as posix_clock_unregister() frees
ptp which is needed in the ptp_cleanup_pin_groups(). Fix this by calling
ptp_cleanup_pin_groups() in ptp_clock_release(), right before ptp is freed.
This makes this patch fix an UAF bug in a patch which fixes an UAF bug.
Reported-by: Antti Laakso <antti.laakso@intel.com> Fixes: a33121e5487b ("ptp: fix the race between the release of ptp_clock and cdev") Link: https://lore.kernel.org/netdev/3d2bd09735dbdaf003585ca376b7c1e5b69a19bd.camel@intel.com/ Signed-off-by: Vladis Dronov <vdronov@redhat.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Array utdm_info is declared as an array of MAX_HDLC_NUM (4) elements
however up to UCC_MAX_NUM (8) elements are potentially being written
to it. Currently we have an array out-of-bounds write error on the
last 4 elements. Fix this by making utdm_info UCC_MAX_NUM elements in
size.
Addresses-Coverity: ("Out-of-bounds write") Fixes: c19b6d246a35 ("drivers/net: support hdlc function for QE-UCC") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lan78xx_tx_bh() makes sure to not exceed MAX_SINGLE_PACKET_SIZE
bytes in the aggregated packets it builds, but does
nothing to prevent large GSO packets being submitted.
Pierre-Francois reported various hangs when/if TSO is enabled.
For localy generated packets, we can use netif_set_gso_max_size()
to limit the size of TSO packets.
Note that forwarded packets could still hit the issue,
so a complete fix might require implementing .ndo_features_check
for this driver, forcing a software segmentation if the size
of the TSO packet exceeds MAX_SINGLE_PACKET_SIZE.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: RENARD Pierre-Francois <pfrenard@gmail.com> Tested-by: RENARD Pierre-Francois <pfrenard@gmail.com> Cc: Stefan Wahren <stefan.wahren@i2se.com> Cc: Woojung Huh <woojung.huh@microchip.com> Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the Datasheet this bit should be 0 (Normal operation) in
default. With the FORCE_LINK_GOOD bit set, it is not possible to get a
link. This patch sets FORCE_LINK_GOOD to the default value after
resetting the phy.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When there is not enough memory and napi_alloc_skb() return NULL,
the HNS driver will print error message, and than try again, if
the memory is not enough for a while, huge error message and the
retry operation will cause soft lockup.
When napi_alloc_skb() return NULL because of no memory, we can
get a warn_alloc() call trace, so this patch deletes the error
message. We already use polling mode to handle irq, but the
retry operation will render the polling weight inactive, this
patch just return budget when the rx is not completed to avoid
dead loop.
Fixes: 36eedfde1a36 ("net: hns: Optimize hns_nic_common_poll for better performance") Fixes: b5996f11ea54 ("net: add Hisilicon Network Subsystem basic ethernet support") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware can not handle short frames below or equal to 32
bytes according to the hardware user manual, and it will trigger
a RAS error when the frame's length is below 33 bytes.
This patch pads the SKB when skb->len is below 33 bytes before
sending it to hardware.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DSA subsystem takes care of netdev statistics since commit 4ed70ce9f01c
("net: dsa: Refactor transmit path to eliminate duplication"), so
any accounting inside tagger callbacks is redundant and can lead to
messing up the stats.
This bug is present in Qualcomm tagger since day 0.
Fixes: cafdc45c949b ("net-next: dsa: add Qualcomm tag RX/TX handler") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexander Lobakin <alobakin@dlink.ru> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reported some bogus lockdep warnings, for example bad unlock
balance in sch_direct_xmit(). They are due to a race condition between
slow path and fast path, that is qdisc_xmit_lock_key gets re-registered
in netdev_update_lockdep_key() on slow path, while we could still
acquire the queue->_xmit_lock on fast path in this small window:
CPU A CPU B
__netif_tx_lock();
lockdep_unregister_key(qdisc_xmit_lock_key);
__netif_tx_unlock();
lockdep_register_key(qdisc_xmit_lock_key);
In fact, unlike the addr_list_lock which has to be reordered when
the master/slave device relationship changes, queue->_xmit_lock is
only acquired on fast path and only when NETIF_F_LLTX is not set,
so there is likely no nested locking for it.
Therefore, we can just get rid of re-registration of
qdisc_xmit_lock_key.
Reported-by: syzbot+4ec99438ed7450da6272@syzkaller.appspotmail.com Fixes: ab92d68fc22f ("net: core: add generic lockdep keys") Cc: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rndis_filter_device_add() allocates an instance of struct rndis_device
which never gets deallocated as rndis_filter_device_remove() sets
net_device->extension which points to the rndis_device struct to NULL,
leaving the rndis_device dangling.
Since net_device->extension is eventually freed in free_netvsc_device(),
we refrain from setting it to NULL inside rndis_filter_device_remove()
Signed-off-by: Mohammed Gamal <mgamal@redhat.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I missed the fact that macvlan_broadcast() can be used both
in RX and TX.
skb_eth_hdr() makes only sense in TX paths, so we can not
use it blindly in macvlan_broadcast()
Fixes: 96cc4b69581d ("macvlan: do not assume mac_header is set in macvlan_broadcast()") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Jurgen Van Ham <juvanham@gmail.com> Tested-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The distributed arp table is using a DHT to store and retrieve MAC address
information for an IP address. This is done using unicast messages to
selected peers. The potential peers are looked up using the IP address and
the VID.
While the IP address is always stored in big endian byte order, this is not
the case of the VID. It can (depending on the host system) either be big
endian or little endian. The host must therefore always convert it to big
endian to ensure that all devices calculate the same peers for the same
lookup data.
Fixes: be1db4f6615b ("batman-adv: make the Distributed ARP Table vlan aware") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For plain text output, it incorrectly prints the pointer value
"void *data". The "void *data" is actually pointing to memory that
contains a bpf-map's value. The intention is to print the content of
the bpf-map's value instead of printing the pointer pointing to the
bpf-map's value.
In this case, a member of the bpf-map's value is a pointer type.
Thus, it should print the "*(void **)data".
Fixes: 22c349e8db89 ("tools: bpftool: fix format strings and arguments for jsonw_printf()") Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Link: https://lore.kernel.org/bpf/20200110231644.3484151-1-kafai@fb.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible to leak time wait and request sockets via the following
BPF pseudo code:
sk = bpf_skc_lookup_tcp(...)
if (sk)
bpf_sk_release(sk)
If sk->sk_state is TCP_NEW_SYN_RECV or TCP_TIME_WAIT the refcount taken
by bpf_skc_lookup_tcp is not undone by bpf_sk_release. This is because
sk_flags is re-used for other data in both kinds of sockets. The check
!sock_flag(sk, SOCK_RCU_FREE)
therefore returns a bogus result. Check that sk_flags is valid by calling
sk_fullsock. Skip checking SOCK_RCU_FREE if we already know that sk is
not a full socket.
Fixes: edbf8c01de5a ("bpf: add skc_lookup_tcp helper") Fixes: f7355a6c0497 ("bpf: Check sk_fullsock() before returning from bpf_sk_lookup()") Signed-off-by: Lorenz Bauer <lmb@cloudflare.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Martin KaFai Lau <kafai@fb.com> Link: https://lore.kernel.org/bpf/20200110132336.26099-1-lmb@cloudflare.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver was doing a synchronous uninterruptible bulk-transfer without
using a timeout. This could lead to the driver hanging on probe due to a
malfunctioning (or malicious) device until the device is physically
disconnected. While sleeping in probe the driver prevents other devices
connected to the same hub from being added to (or removed from) the bus.
An arbitrary limit of five seconds should be more than enough.
Fixes: dbafc28955fa ("NFC: pn533: don't send USB data off of the stack") Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A missing generation check during DELTABLE processing causes it to queue
the DELFLOWTABLE operation a second time, so we corrupt the list here:
case NFT_MSG_DELFLOWTABLE:
list_del_rcu(&nft_trans_flowtable(trans)->list);
nf_tables_flowtable_notify(&trans->ctx,
because we have two different DELFLOWTABLE transactions for the same
flowtable. We then call list_del_rcu() twice for the same flowtable->list.
The object handling seems to suffer from the same bug so add a generation
check too and only queue delete transactions for flowtables/objects that
are still active in the next generation.
This patch fixes a WARN_ON in nft_set_destroy() due to missing
set reference count drop from the preparation phase. This is triggered
by the module autoload path. Do not exercise the abort path from
nft_request_module() while preparation phase cleaning up is still
pending.
Update comment on the code to describe the new behaviour.
Reported-by: Marco Oliverio <marco.oliverio@tanaza.com> Fixes: 452238e8d5ff ("netfilter: nf_tables: add and use helper for module autoload") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8303b7e8f018 ("netfilter: nat: fix spurious connection timeouts")
made nf_nat_icmp_reply_translation() use icmp_manip_pkt() as the l4
manipulation function for the outer packet on ICMP errors.
However, icmp_manip_pkt() assumes the packet has an 'id' field which
is not correct for all types of ICMP messages.
This is not correct for ICMP error packets, and leads to bogus bytes
being written the ICMP header, which can be wrongfully regarded as
'length' bytes by RFC 4884 compliant receivers.
Fix by assigning the 'id' field only for ICMP messages that have this
semantic.
An earlier commit (1b789577f655060d98d20e,
"netfilter: arp_tables: init netns pointer in xt_tgchk_param struct")
fixed missing net initialization for arptables, but turns out it was
incomplete. We can get a very similar struct net NULL deref during
error unwinding:
map->members is freed by ip_set_free() right before using it in
mtype_ext_cleanup() again. So we just have to move it down.
Reported-by: syzbot+4c3cc6dbe7259dbf9054@syzkaller.appspotmail.com Fixes: 40cd63bf33b2 ("netfilter: ipset: Support extensions which need a per data destroy function") Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When handling devm_gpiod_get_optional() errors, free the memory already
allocated. This fixes Smatch warnings:
drivers/i2c/busses/i2c-iop3xx.c:437 iop3xx_i2c_probe() warn: possible memory leak of 'new_adapter'
drivers/i2c/busses/i2c-iop3xx.c:442 iop3xx_i2c_probe() warn: possible memory leak of 'new_adapter'
Fixes: fdb7e884ad61 ("i2c: iop: Use GPIO descriptors") Reported-by: kbuild test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now in tcp_bpf_recvmsg, sock read data first from sk_receive_queue
if not empty than psock->ingress_msg otherwise. If a FIN packet arrives
and there's also some data in psock->ingress_msg, the data in
psock->ingress_msg will be purged. It is always happen when request to a
HTTP1.0 server like python SimpleHTTPServer since the server send FIN
packet after data is sent out.
Fixes: 604326b41a6fb ("bpf, sockmap: convert to generic sk_msg interface") Reported-by: Arika Chen <eaglesora@gmail.com> Suggested-by: Arika Chen <eaglesora@gmail.com> Signed-off-by: Lingpeng Chen <forrest0579@gmail.com> Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Song Liu <songliubraving@fb.com> Link: https://lore.kernel.org/bpf/20200109014833.18951-1-forrest0579@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fragments attached to a skb can be part of a compound page. In that case,
page_ref_inc will increment the refcount for the wrong page. Fix this by
using get_page instead, which calls page_ref_inc on the compound head and
also checks for overflow.
Fixes: 2b67f944f88c ("cfg80211: reuse existing page fragments in A-MSDU rx") Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20200113182107.20461-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / arm / linux.git / log