This limits CLEANFILES removal to just bsd.obj.mk now and removes the need
for NOPATH_FILES.
This reverts r96529 which was done due to the command line being too long
for libc. Since then all architectures now use 256k for ARG_MAX (r170102).
Regardless of that, the libc CLEANFILES is only 72k now. Others
may be larger but not likely to hit the limit. If needed, we can improve
the bsd.obj.mk clean: target to split up the list via bmake features.
This also removes some workarounds that are no longer needed.
- a.out removal
- OBJS.tmp, which has not been needed since r117080.
- *.so, which has not been needed since a .so->.So rename in r42450.
This also fixes STATICOBJS and SHLIB_LINK not being in the .NOPATH list.
adrian [Tue, 22 Sep 2015 02:57:18 +0000 (02:57 +0000)]
Begin fleshing out basic power-on / power-off and A-MPDU TX support.
* Add a new method to control NIC poweron / network-sleep / power off;
* Add in A-MPDU TX negotiation support, but comment it out because it
does break TX traffic;
* blank out the tx buffer before sending a firmware message, just in case;
* go into network-sleep once associated;
TODO:
* figure out why ampdu negotiation isn't working and breaking TX traffic,
then enable it.
Fix installation of 32bit libraries after r288074.
FILES is not used when LIBRARIES_ONLY is set, which is used to build and
install the lib32 sysroot. All of the csu files do quality as "libraries"
for this case so just undefine LIBRARIES_ONLY.
This is still better than the previous realinstall handling as it does
not hook into META_MODE properly.
des [Mon, 21 Sep 2015 17:26:35 +0000 (17:26 +0000)]
Restore the upstream (and documented) behavior of searching for modules
both in /usr/lib and /usr/local/lib, thus simplifying the use of modules
from ports, without breaking the compat32 case again.
Ensure that maxproc does not exceed pid_max, at the time of boot.
Changes to kern.pid_max mib after the boot can break this relation.
The maxfiles value was calculated by the MAXFILES formula based on
maxproc value, but this change decouples them, and MAXFILES now
references maxusers. Without manual tuning, the maxfiles default
value remains as it was prior to this commit. But for systems which
have tuned maxproc and rely on maxfiles to adjust, additional
reconfiguration is needed.
Reported by: rwatson
Reviewed by: emaste
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
In the UDP over IPv6 implementation several cases are using the wrong protocol,
e.g., based on wrong "next header" assumptions (which does not have to point to
the upper layer protocol), or using hard-coded UDP instead of UDP or UDP-Lite
possibly switching protocols. Fix those cases for UDP-Lite to work correctly.
https://github.com/illumos/illumos-gate/commit/c546f36aa898d913ff77674fb5ff97f15b2e08b4
https://www.illumos.org/issues/6220
5408 introduced a memleak in l2arc, namely the member b_thawed gets leaked when
an arc_hdr is realloced from full to l2only.
Reviewed by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Reviewed by: Simon Klinkert <simon.klinkert@gmail.com>
Reviewed by: George Wilson <george@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Author: Arne Jansen <sensille@gmx.net>
Unify nd6 state switching by using newly-created nd6_llinfo_setstate()
function. The change is mostly mechanical with the following exception:
Last piece of nd6_resolve_slow() was refactored: ND6_LLINFO_PERMANENT
condition was removed as always-true, explicit ND6_LLINFO_NOSTATE ->
ND6_LLINFO_INCOMPLETE state transition was removed as duplicate.
Add "stale" timer back to nd6_cache_lladdr().
Setting timer was accidentally removed in r276844 due to misleading
comment on its meaningless. Add it back to restore proper behaviour.
adrian [Mon, 21 Sep 2015 02:30:22 +0000 (02:30 +0000)]
Convert if_rsu to use a deferred transmit task rather than using rsu_start()
to do it directly.
Ensure that we re-queue starting transmit upon TX completion.
This solves two issues:
* It stops tx stalls - before this, if the transmit path filled the
mbuf queue then it'd never start another transmit.
* It enforces ordering - this is very required for 802.11n which
requires frames to be transmitted in the order they're queued.
Since everything remotely involved in USB has an unlock/thing/relock
pattern with that mutex, the only way to guarantee TX ordering is
to 100% defer it into a separate thread.
This now survives an iperf test and gets a reliable 30mbit/sec.
adrian [Mon, 21 Sep 2015 02:12:01 +0000 (02:12 +0000)]
Drain the mbuf queue upon rsu_stop().
Correctly (I hope!) remove net80211 references before doing so.
Just doing a dumb mbufq drain isn't enough.
If enough traffic occurs and the mbuf queue fills up then transmit
stalls (which I'm not fixing in this commit!) but then the mbuf queue
stays full until the driver is removed. There's also the net80211
node refcounting leak.
This just ensures that during rsu_stop and detach the mbuf queue
is purged (and references!) so the queue-full situation can be
recovered from.
Ensure that when a blockable open of fifo returns success, a valid
file descriptor opened for complimentary access exists as well.
The implementation of the guarantee is done by counting the
generations of readers and writers opens. We return success and not
EINTR or ERESTART error, when the sleep for complimentary opening is
interrupted, but the generation was changed during the sleep.
Longer explanation: assume there are two threads, A doing open("fifo",
O_RDONLY) and B doing open("fifo", O_WRONLY), and no other threads
either trying to open the fifo, nor there are any file descriptors
referencing the fifo. Before the change, it was possible e.g. for for
thread A to return a valid file descriptor, while thread B returned
EINTR if a signal to B was delivered simultaneously with the wakeup
from A. After the change, in this situation both A::open() and
B::open() succeed and the signal is made "as if" it was noticed
slightly later. Note that the signal actual delivery is not changed,
it is done by ast on syscall return path, so signal handler is still
executed before first instruction after syscall.
See PR for the code demonstrating the issue.
PR: 203162
Reported by: Victor Stinner victor.stinner@gmail.com
Reviewed by: jilles
Tested by: bapt, pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Correct a non-fatal error in vm_pageout_worker(). vm_pageout_worker()
should not assume that vm_pages_needed will remain set while it sleeps.
Other threads can clear vm_pages_needed by performing a sufficient
number of vm_page_free() calls, e.g., process termination. The effect
of this error was that vm_pageout_worker() would free and/or launder
pages when, in fact, there was no shortage of free pages.
Rewrite a nearby comment to describe all of the possible cases and not
just the most common case. The problem being that the comment made
the most common case seem like the only case.
Add support for weak symbols to the kernel linkers. It means that
linkers no longer raise an error when undefined weak symbols are
found, but relocate as if the symbol value was 0. Note that we do not
repeat the mistake of userspace dynamic linker of making the symbol
lookup prefer non-weak symbol definition over the weak one, if both
are available. In fact, kernel linker uses the first definition
found, and ignores duplicates.
Signature of the elf_lookup() and elf_obj_lookup() functions changed
to split result/error code and the symbol address returned.
Otherwise, it is impossible to return zero address as the symbol
value, to MD relocation code. This explains the mechanical changes in
elf_machdep.c sources.
The powerpc64 R_PPC_JMP_SLOT handler did not checked error from the
lookup() call, the patch leaves the code as is (untested).
Reported by: glebius
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Add PF_LOCAL support in getaddrinfo(3) and getnameinfo(3):
- In a PF_LOCAL address, "hostname" must begins with '/' and "servname"
is always NULL. All of ai_flags are ignored.
- PF_UNSPEC matches PF_LOCAL. EAI_SERVICE is not returned to make
AF-independent programming easier; "servname" is always ignored
in PF_LOCAL. In practice, PF_INET* and PF_LOCAL are
mutually-exclusive because a hostname which begins with '/' is invalid
in PF_INET*. No domain name resolution is performed for a PF_LOCAL address.
- Use NI_MAXHOST-long buffer for getnameinfo().
Although INET6_ADDRSTRLEN was designed to hold the longest
IPv6 address in IPv4-mapped address format a long time ago,
getnameinfo() can return scope identifier in addition to it.
- Fix a crash on a rpc entry when an IPv6 address is explicitly specified
in -a flag.
- Fix a bug that sockaddr_in was used where sockaddr_in6 should have
been used. This was not actually harmful because offsetof(struct
sockaddr_in, sin_port) is equal to offsetof(struct sockaddr_in6,
sin6_port).
'sin' is never used after assignment. Looking at the context, it seems
that it belongs the commented out section of code so make it part of that
section.
Always execute REPORT LUNS and REQUEST SENSE commands locally.
REPORT LUNS command is more related to target rather then specific LUN.
This node may be primary for LUNs for some reason unknown to another,
and command forwarded to another node won't be able to report them.
REQUEST SENSE is related to LUN, but in our implementation it reports
only UAs and CAs, that are stored locally rather then on primary node.
projects / people / julieng / freebsd.git / log