Riku Voipio [Thu, 3 Dec 2009 13:56:08 +0000 (15:56 +0200)]
usb-musb: convert fifo to 8bit and add more registers
Convert musb fifo to 8bit to allow 8/16/32bit access
MUSB allows reading and writing to the fifo in 32/16/8 bit
width. The Linux kernel does this sometimes, most usually at
the end of writing the packet to allow packet to end at a
odd bytecount.
Convert the fifo to 8bit allows removing lots of shifts
which shows that the fifo is more natural as 8bit.
While at it, add multiple missing register definitions and
and cleanup debug prints.
Gerd Hoffmann [Fri, 18 Dec 2009 11:01:12 +0000 (12:01 +0100)]
roms: remove option rom packing logic
Now that we load the option roms via fw_cfg, we can stop copying
them to the 0xc000 -> 0xe000. The patch does just that.
Also the rom loader gets simplified as all remaining users of the
rom loader load the bits at a fixed address so the packing and
aligning logic can go away.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Gerd Hoffmann [Fri, 18 Dec 2009 11:01:10 +0000 (12:01 +0100)]
fw_cfg: add API for file transfer.
This patch adds a file transfer interface to fw_cfg. Intended to be
used for passing non-pci option roms and vgabios to seabios. Namespace
is modeled after the existing cbfs filesystem support in seabios.
Reading the new FW_CFG_FILE_DIR entry returns a file list.
Fields there are in network byte order (aka bigendian).
aliguori: fix fw_cfg.h for multiboot.bin, add proper fw_cfg.h declarations,
quiet fprintf() in fw_cfg.c
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Gerd Hoffmann [Fri, 18 Dec 2009 11:01:08 +0000 (12:01 +0100)]
pci romfiles: add property, add default to PCIDeviceInfo
This patch adds a romfile property to the pci bus. It allows to specify
a romfile to load into the rom bar of the pci device. The default value
comes from a new field in PCIDeviceInfo. The property allows to change
the file and also to disable the rom loading using an empty string.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Anthony Liguori [Fri, 18 Dec 2009 11:01:07 +0000 (12:01 +0100)]
Support PCI based option rom loading
Currently, we preload option roms into the option rom space in memory. This
prevents DDIM from functioning correctly which severely limits the number
of roms we can support.
This patch introduces a pci_add_option_rom() which registers the
PCI_ROM_ADDRESS bar which points to our option rom. It also converts over
the cirrus vga adapter, the rtl8139, virtio, and the e1000 to use this
new mechanism.
The result is that PXE boot functions even with three unique types of cards.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com> Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Anthony Liguori [Thu, 17 Dec 2009 22:08:10 +0000 (08:08 +1000)]
VMware VGA: Only enable dirty log tracking when fifo is disabled
This patch enables dirty log tracking whenever it's needed and disables it
when it is not.
We unconditionally enable dirty log tracking on reset, restart dirty log
tracking when PCI IO regions are remapped, and disable/enable it based on
commands from the guest.
Rebased-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Anthony Liguori [Thu, 17 Dec 2009 22:08:09 +0000 (08:08 +1000)]
Fix VMware VGA depth computation
VMware VGA requires that the depth presented to the guest is the same as the
DisplaySurface that it renders to. This is because it performs a very simple
memcpy() to blit from one surface to another.
We currently hardcode a 24-bit depth. The surface allocator for SDL may, and
usually will, allocate a surface with a different depth causing screen
corruption.
This changes the code to allocate the DisplaySurface before initializing the
device which allows the depth of the DisplaySurface to be used instead of
hardcoding something.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Anthony Liguori [Thu, 17 Dec 2009 22:08:07 +0000 (08:08 +1000)]
Make sure to enable dirty tracking of VBE vram mapping
Apparently, VBE maps the VGA vram to a fixed physical location. KVM requires
that all mappings of the VGA vram have dirty tracking enabled on them. Any
access to the VGA vram through the VBE mapping currently fails to result in
dirty page tracking updates causing a black screen.
This is the true root cause of VMware VGA not working correctly under KVM and
likely also an issue with some of the std-vga black screen issues too.
Cirrus does not enable VBE so it would not be a problem when using Cirrus.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com> Rebased-by: Dave Airlie <airlied@redhat.com>
Gerd Hoffmann [Wed, 16 Dec 2009 13:22:11 +0000 (14:22 +0100)]
qdev: improve property error reporting.
Add a error message in case we fail to parse a qdev property.
Also make qemu not abort() in case setting a global property can't be
set. This used to be a clear programming error. The introduction of
the -global switch changed that though, so better exit instead (after
printing the new error message).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Luiz Capitulino [Mon, 14 Dec 2009 20:53:24 +0000 (18:53 -0200)]
monitor: Catch printing to non-existent monitor
The monitor_vprintf() function now touches the 'mon' pointer
before calling monitor_puts(), this causes block migration
to segfault as its functions call monitor_printf() with a
NULL 'mon'.
To fix the problem this commit moves the 'mon' NULL check
from monitor_puts() to monitor_vprintf().
This can potentially hide bugs, but for some reason this has
been the behavior for a long time.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Avoid permanently disabled QEMU monitor when UNIX migration fails
If a UNIX migration command is attempt to a UNIX socket which does
not exist, then the monitor is suspended, but never resumed. This
prevents any further use of the monitor
* migration-unix.c: Only call migrate_fd_monitor_suspend() once
connected to the UNIX socket.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Kevin Wolf [Fri, 4 Dec 2009 16:19:25 +0000 (17:19 +0100)]
Fix loading of ELF multiboot kernels
The multiboot implementation assumed that there is only one program header
(which contains the entry point) and that the entry point is at the start of
the code. This doesn't hold true generally and caused too little data to be
loaded.
Fix the loading code to pass the whole loaded data to the Multiboot Option ROM.
Signed-off-by: Kevin Wolf <kwolf@redhat.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Kevin Wolf [Fri, 4 Dec 2009 11:06:32 +0000 (12:06 +0100)]
Revert "Rename DriveInfo.onerror to on_write_error" (fix mismerge)
Part of the first patch of the -drive rerror series has been merged once more
on top of the rest of the series. This effectively disables the rerror option
and always goes with the default value. Reverting the commit re-enables the
option.
Jan Kiszka [Mon, 14 Dec 2009 11:26:17 +0000 (12:26 +0100)]
kvm: x86: Use separate exception_injected CPUState field
Marcelo correctly remarked that there are usage conflicts between QEMU
core code and KVM /wrt exception_index. So spend a separate field and
also save/restore it properly.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Alexander Graf [Thu, 17 Dec 2009 12:06:09 +0000 (13:06 +0100)]
S390: Don't tell guest we're updating config space
Currently we always set the "config space changed" bit to 1 when triggering
any virtio interrupt. While that worked in 2.6.27, newer kernels interpret
that value as "only the config space changed and nothing else happened".
Since we usually trigger interrupts to tell the guest that something did
happen, we just not tell it the config space changed for now until we
implement the correct callback for that.
Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Alexander Graf [Thu, 17 Dec 2009 12:06:07 +0000 (13:06 +0100)]
S390: Loop through virtio console devices
We used to always create one single virtio console device. This breaks when
either zero of multiple virtio console devices are requested, so let's use
the same code as on x86.
Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Alexander Graf [Thu, 17 Dec 2009 12:56:47 +0000 (13:56 +0100)]
target-s390: Fail on unknown instructions
We were being a bit too nice and didn't give the guest an invalid instruction
interrupt.
While that works, it's not exactly the fastest thing to do, since now the
guest doesn't know that we're not really implementing that instruction, so it
continues doing it.
We run into this with the set_page_unstable hint instruction. So let's bail out
in these cases.
Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Andre Przywara [Fri, 18 Dec 2009 09:45:07 +0000 (10:45 +0100)]
osdep: Fix runtime failure on older Linux kernels
If QEMU finds newer kernel header files on compilation time, it will use
advertised features like pipe2 or SOCK_CLOEXEC by just doing a compile test.
If later the executables are executed on an older kernel (<2.6.27,
like Xen Dom0 2.6.18), then QEMU will fail on opening sockets and creating
pipes and returns the rather unspecific "qemu_init_main_loop failed".
This patch fixes this by checking the return values of these calls
for EINVAL and ENOSYS and falling back to the older versions automatically.
Signed-off-by: Andre Przywara <andre.przywara@amd.com> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Juergen Lock [Mon, 14 Dec 2009 20:54:43 +0000 (21:54 +0100)]
Fix a make -j race
Make libuser.a depend on $(GENERATED_HEADERS) too so make -j won't start
building it before the headers exist. (There may be more bugs like this
but at least this makes (g)make -j4 started from scratch on a quadcore
now always complete here again.)
There was a bug in float32_to_s that incorrectly mapped a zero exponent
to 0x38. This meant 0.0f != 0. At the same time, fix a generic type
punning bug in helper_memory_to_s and helper_s_to_memory.
Signed-off-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The old fcmov implementation had a typo:
- tcg_gen_mov_i64(cpu_fir[rc], cpu_fir[ra]);
which moved the condition, not the second source, to the destination.
But it's also easy to implement the simplified fp comparison inline.
Signed-off-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Stefan Weil [Tue, 15 Dec 2009 13:43:40 +0000 (14:43 +0100)]
target-mips: 4Kc, 4KEc cores do not support MIPS16
4Kc, 4KEc cores do not support MIPS16, so not only the
CP0_Config1 had to be fixed (see previous patch),
but also MIPS16 instructions must not be executed.
(Hint from Nathan Froyd, thanks).
Signed-off-by: Stefan Weil <weil@mail.berlios.de> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
target-alpha: Implement RD/WRUNIQUE in the translator
When emulating user-mode only, there's no reason to exit
the translation block to effect a call_pal. We can generate
a move to/from the unique slot directly.
Signed-off-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
target-alpha: Rewrite gen_ext_[hl] in terms of zapnot.
The architecture manual specifies the EXT instructions
in terms of the ZAPNOT operation; writing it that way in
the translator makes things a bit clearer.
Signed-off-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Generic disassembly was incorrectly keyed on ALPHA_DEBUG_DISAS
rather than the generic DEBUG_DISAS. Use qemu_log_mask for
additional LOG_DISAS output. Delete some random insn_count
logging noise from gen_intermediate_code_internal.
Signed-off-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Nathan Froyd [Fri, 11 Dec 2009 17:29:20 +0000 (09:29 -0800)]
target-mips: fix user-mode emulation startup
Running programs with the MIPS user-mode emulator fails during dynamic
loading, as floating-point instructions are not enabled in in
env->hflags. Move the code for doing so from fpu_init to cpu_reset so
the MIPS_HFLAG_{FPU,F64} setting doesn't get clobbered by cpu_reset
setting env->hflags to MIPS_HFLAG_UM.
The same end can be achieved by swapping the ordering of fpu_init and
cpu_reset in cpu_mips_init, but it seemed better to consolidate the
CONFIG_USER_ONLY code into a single location.
Andre Przywara [Mon, 7 Dec 2009 11:05:38 +0000 (12:05 +0100)]
target-i386: Update CPUID feature set for TCG
The CPUID features QEMU presented to the guest were not up-to-date
with QEMU's emulated feature set.
Add the missing bits of recent (and not so recent) additions to
QEMU's emulation engine.
For stability reasons only the user mode usable bits are exposed for
now, features like Monitor or CR8LEG are left out.
Signed-off-by: Andre Przywara <andre.przywara@amd.com> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
1. Add correct definitions of error numbers.
2. Implement SYS_osf_sigprocmask
3. Implement SYS_osf_get/setsysinfo for IEEE_FP_CONTROL.
This last requires exposing the FPCR value to do_syscall.
Since this value is actually split up into the float_status,
expose routines from helper.c to access it.
Finally, also add a float_exception_mask field to float_status.
We don't actually use it to control delivery of exceptions to
the emulator yet, but simply hold the value that we placed there
when loading/storing the FPCR.
Signed-off-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Nathan Froyd [Tue, 8 Dec 2009 16:06:29 +0000 (08:06 -0800)]
target-mips: add mips16 instruction decoding
There's no good way to add this incrementally, so we do it all at once.
The only changes to shared code are in handle_delay_slot. We need to
flip ISAMode when doing a jump-and-exchange. We also need to set
ISAMode the low bit of the target address for jump-to-register.
Also, since we're now adding bits that can be in MIPS_HFLAG_BMASK_EXT,
make sure we use MIPS_HFLAG_BMASK_BASE in the places where we just want
basic information about a branch.
Nathan Froyd [Tue, 8 Dec 2009 16:06:24 +0000 (08:06 -0800)]
target-mips: move ROTR and ROTRV inside gen_shift_{imm, }
It's easier to implement mips16 shift instructions if we're not
examining the opcode inside gen_shift_{imm,}. So move ROTR and ROTRV
and do the special-case handling of SRL and SRLV inside decode_opc.
Likewise for their 64-bit counterparts.
projects / qemu-upstream-4.6-testing.git / log