q800: implement mac rom reset function for BIOS-less mode
On Linux, calling `reboot(RB_AUTOBOOT);` will result in
arch/m68k/mac/misc.c's mac_reset function being called. That in turn
looks at the rombase (or uses 0x40800000 is there's no rombase), adds
0xa, and jumps to that address. At the moment, there's nothing there, so
the kernel just crashes when trying to reboot. So, this commit adds a
very simple implementation at that location, which just writes to via2
to power down. We also correct the value of ROMBASE while we're at it.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20200102120150.281082-1-Jason@zx2c4.com> Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Laurent Vivier [Thu, 19 Dec 2019 20:14:38 +0000 (21:14 +0100)]
q800: fix mac_via RTC PRAM commands
The command byte is not decoded correctly.
This patch reworks the RTC/PRAM interface and fixes the problem.
It adds a comment before the function to explain how are encoded commands
and some trace-events to ease debugging.
Bug: https://bugs.launchpad.net/qemu/+bug/1856549 Fixes: 6dca62a000 ("hw/m68k: add VIA support") Signed-off-by: Laurent Vivier <laurent@vivier.eu> Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20191219201439.84804-2-laurent@vivier.eu>
* remotes/xtensa/tags/20200106-xtensa:
target/xtensa: use MPU background map from core configuration
target/xtensa: import xtensa/config/core-isa.h
target/xtensa: fix ps.ring use in MPU configs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell [Mon, 6 Jan 2020 18:22:42 +0000 (18:22 +0000)]
Merge remote-tracking branch 'remotes/elmarco/tags/dbus-vmstate7-pull-request' into staging
Add dbus-vmstate
Hi,
With external processes or helpers participating to the VM support, it
becomes necessary to handle their migration. Various options exist to
transfer their state:
1) as the VM memory, RAM or devices (we could say that's how
vhost-user devices can be handled today, they are expected to
restore from ring state)
2) other "vmstate" (as with TPM emulator state blobs)
3) left to be handled by management layer
1) is not practical, since an external processes may legitimatelly
need arbitrary state date to back a device or a service, or may not
even have an associated device.
2) needs ad-hoc code for each helper, but is simple and working
3) is complicated for management layer, QEMU has the migration timing
The proposed "dbus-vmstate" object will connect to a given D-Bus
address, and save/load from org.qemu.VMState1 owners on migration.
Thus helpers can easily have their state migrated with QEMU, without
implementing ad-hoc support (such as done for TPM emulation)
D-Bus is ubiquitous on Linux (it is systemd IPC), and can be made to
work on various other OSes. There are several implementations and good
bindings for various languages. (the tests/dbus-vmstate-test.c is a
good example of how simple the implementation of services can be, even
in C)
dbus-vmstate is put into use by the libvirt series "[PATCH 00/23] Use
a slirp helper process".
v2:
- fix build with broken mingw-glib
# gpg: Signature made Mon 06 Jan 2020 14:43:35 GMT
# gpg: using RSA key 87A9BD933F87C606D276F62DDAE8E10975969CE5
# gpg: issuer "marcandre.lureau@redhat.com"
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>" [full]
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>" [full]
# Primary key fingerprint: 87A9 BD93 3F87 C606 D276 F62D DAE8 E109 7596 9CE5
* remotes/elmarco/tags/dbus-vmstate7-pull-request:
tests: add dbus-vmstate-test
tests: add migration-helpers unit
dockerfiles: add dbus-daemon to some of latest distributions
configure: add GDBUS_CODEGEN
Add dbus-vmstate object
util: add dbus helper unit
docs: start a document to describe D-Bus usage
vmstate: replace DeviceState with VMStateIf
vmstate: add qom interface to get id
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell [Mon, 6 Jan 2020 17:44:22 +0000 (17:44 +0000)]
Merge remote-tracking branch 'remotes/maxreitz/tags/pull-block-2020-01-06' into staging
Block patches:
- Minor fixes and tests from the freeze period (too minor to be included
in 4.2)
- Allow many bash iotests to test qcow2's external data file feature
- Add compress filter driver
- Fix Python iotests after 6f6e1698a6
- Fix for the backup job
# gpg: Signature made Mon 06 Jan 2020 14:33:06 GMT
# gpg: using RSA key 91BEB60A30DB3E8857D11829F407DB0061D5CF40
# gpg: issuer "mreitz@redhat.com"
# gpg: Good signature from "Max Reitz <mreitz@redhat.com>" [full]
# Primary key fingerprint: 91BE B60A 30DB 3E88 57D1 1829 F407 DB00 61D5 CF40
* remotes/maxreitz/tags/pull-block-2020-01-06: (34 commits)
backup-top: Begin drain earlier
tests/qemu-iotests: Update tests to recent desugarized -accel option
tests/qemu-iotests: add case to write compressed data of multiple clusters
qcow2: Allow writing compressed data of multiple clusters
block: introduce compress filter driver
iotests: Allow check -o data_file
iotests: Disable data_file where it cannot be used
iotests: Make 198 work with data_file
iotests: Make 137 work with data_file
iotests: Make 110 work with data_file
iotests: Make 091 work with data_file
iotests: Avoid cp/mv of test images
iotests: Use _rm_test_img for deleting test images
iotests: Avoid qemu-img create
iotests: Drop IMGOPTS use in 267
iotests: Replace IMGOPTS='' by --no-opts
iotests: Replace IMGOPTS= by -o
iotests: Inject space into -ocompat=0.10 in 051
iotests: Add -o and --no-opts to _make_test_img
iotests: Let _make_test_img parse its parameters
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* remotes/kraxel/tags/audio-20200106-pull-request:
audio: fix integer overflow
paaudio: wait until the recording stream is ready
paaudio: try to drain the recording stream
paaudio: drop recording stream in qpa_fini_in
hda-codec: fix recording rate control
hda-codec: fix playback rate control
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell [Mon, 6 Jan 2020 14:51:51 +0000 (14:51 +0000)]
Merge remote-tracking branch 'remotes/elmarco/tags/screendump-pull-request' into staging
console: screendump improvements
Hi,
The following patches have been extracted from the "[PATCH v6 00/25]
monitor: add asynchronous command type", as they are
reviewable/mergeable independantly.
They introduce some internal API changes, and fix
qemu_open()/qemu_close()/unlink() misusages which should be quite
harmless.
# gpg: Signature made Fri 03 Jan 2020 09:07:51 GMT
# gpg: using RSA key 87A9BD933F87C606D276F62DDAE8E10975969CE5
# gpg: issuer "marcandre.lureau@redhat.com"
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>" [full]
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>" [full]
# Primary key fingerprint: 87A9 BD93 3F87 C606 D276 F62D DAE8 E109 7596 9CE5
* remotes/elmarco/tags/screendump-pull-request:
screendump: use qemu_unlink()
osdep: add qemu_unlink()
screendump: replace FILE with QIOChannel and fix close()/qemu_close()
object: add g_autoptr support
ui: add pixman image g_autoptr support
ppm-save: pass opened fd
console: add graphic_hw_update_done()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When instantiated, this object will connect to the given D-Bus bus
"addr". During migration, it will take/restore the data from
org.qemu.VMState1 instances. See documentation for details.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Replace DeviceState dependency with VMStateIf on vmstate API.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Reviewed-by: Daniel P. Berrangé <berrange@redhat.com> Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com> Acked-by: Halil Pasic <pasic@linux.ibm.com>
Add an interface to get the instance id, instead of depending on
Device and qdev_get_dev_path().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Reviewed-by: Daniel P. Berrangé <berrange@redhat.com> Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
# gpg: Signature made Fri 20 Dec 2019 19:19:02 GMT
# gpg: using RSA key 5A322FD5ABC4D3DBACCFD1AA2807936F984DC5A6
# gpg: issuer "ehabkost@redhat.com"
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>" [full]
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/x86-and-machine-pull-request:
numa: properly check if numa is supported
numa: remove not needed check
i386: Resolve CPU models to v1 by default
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Max Reitz [Thu, 19 Dec 2019 18:26:38 +0000 (19:26 +0100)]
backup-top: Begin drain earlier
When dropping backup-top, we need to drain the node before freeing the
BlockCopyState. Otherwise, requests may still be in flight and then the
assertion in shres_destroy() will fail.
(This becomes visible in intermittent failure of 056.)
Cc: qemu-stable@nongnu.org Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191219182638.104621-1-mreitz@redhat.com Signed-off-by: Max Reitz <mreitz@redhat.com>
tests/qemu-iotests: Update tests to recent desugarized -accel option
Commit 6f6e1698a6 desugarized "-machine accel=" to a list
of "-accel" options. Since now "-machine accel" and "-accel"
became incompatible, update the iotests to the new format.
tests/qemu-iotests: add case to write compressed data of multiple clusters
Add the case to the iotest #214 that checks possibility of writing
compressed data of more than one cluster size. The test case involves
the compress filter driver showing a sample usage of that.
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com> Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 1575288906-551879-4-git-send-email-andrey.shinkevich@virtuozzo.com Signed-off-by: Max Reitz <mreitz@redhat.com>
qcow2: Allow writing compressed data of multiple clusters
QEMU currently supports writing compressed data of the size equal to
one cluster. This patch allows writing QCOW2 compressed data that
exceed one cluster. Now, we split buffered data into separate clusters
and write them compressed using the block/aio_task API.
Suggested-by: Pavel Butsykin <pbutsykin@virtuozzo.com> Suggested-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com> Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 1575288906-551879-3-git-send-email-andrey.shinkevich@virtuozzo.com Signed-off-by: Max Reitz <mreitz@redhat.com>
Allow writing all the data compressed through the filter driver.
The written data will be aligned by the cluster size.
Based on the QEMU current implementation, that data can be written to
unallocated clusters only. May be used for a backup job.
Suggested-by: Max Reitz <mreitz@redhat.com> Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com> Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 1575288906-551879-2-git-send-email-andrey.shinkevich@virtuozzo.com
[mreitz: Replace NULL bdrv_get_format_name() by "(no format)"] Signed-off-by: Max Reitz <mreitz@redhat.com>
Max Reitz [Thu, 7 Nov 2019 16:37:08 +0000 (17:37 +0100)]
iotests: Allow check -o data_file
The problem with allowing the data_file option is that you want to use a
different data file per image used in the test. Therefore, we need to
allow patterns like -o data_file='$TEST_IMG.data_file'.
Then, we need to filter it out from qemu-img map, qemu-img create, and
remove the data file in _rm_test_img.
Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-id: 20191107163708.833192-23-mreitz@redhat.com Signed-off-by: Max Reitz <mreitz@redhat.com>
Max Reitz [Thu, 7 Nov 2019 16:37:07 +0000 (17:37 +0100)]
iotests: Disable data_file where it cannot be used
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191107163708.833192-22-mreitz@redhat.com
[mreitz: Also disable 273] Signed-off-by: Max Reitz <mreitz@redhat.com>
Max Reitz [Thu, 7 Nov 2019 16:37:05 +0000 (17:37 +0100)]
iotests: Make 137 work with data_file
When using an external data file, there are no refcounts for data
clusters. We thus have to adjust the corruption test in this patch to
not be based around a data cluster allocation, but the L2 table
allocation (L2 tables are still refcounted with external data files).
Furthermore, we should not print qcow2.py's list of incompatible
features because it differs depending on whether there is an external
data file or not.
With those two changes, the test will work both with and without
external data files (once that options works with the iotests at all).
Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-id: 20191107163708.833192-20-mreitz@redhat.com Signed-off-by: Max Reitz <mreitz@redhat.com>
Max Reitz [Thu, 7 Nov 2019 16:37:04 +0000 (17:37 +0100)]
iotests: Make 110 work with data_file
The only difference is that the json:{} filename of the image looks
different. We actually do not care about that filename in this test, we
are only interested in (1) that there is a json:{} filename, and (2)
whether the backing filename can be constructed.
So just filter out the json:{} data, thus making this test pass both
with and without data_file.
Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-id: 20191107163708.833192-19-mreitz@redhat.com Signed-off-by: Max Reitz <mreitz@redhat.com>
Max Reitz [Thu, 7 Nov 2019 16:37:03 +0000 (17:37 +0100)]
iotests: Make 091 work with data_file
The image end offset as reported by qemu-img check is different when
using an external data file; we do not care about its value here, so we
can just filter it. Incidentally, common.rc already has _check_test_img
for us which does exactly that.
Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-id: 20191107163708.833192-18-mreitz@redhat.com Signed-off-by: Max Reitz <mreitz@redhat.com>
Max Reitz [Thu, 7 Nov 2019 16:36:59 +0000 (17:36 +0100)]
iotests: Drop IMGOPTS use in 267
Overwriting IMGOPTS means ignoring all user-supplied options, which is
not what we want. Replace the current IMGOPTS use by a new BACKING_FILE
variable.
Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-id: 20191107163708.833192-14-mreitz@redhat.com Signed-off-by: Max Reitz <mreitz@redhat.com>
Max Reitz [Thu, 7 Nov 2019 16:36:57 +0000 (17:36 +0100)]
iotests: Replace IMGOPTS= by -o
Tests should not overwrite all user-supplied image options, but only add
to it (which will effectively overwrite conflicting values). Accomplish
this by passing options to _make_test_img via -o instead of $IMGOPTS.
For some tests, there is no functional change because they already only
appended options to IMGOPTS. For these, this patch is just a
simplification.
For others, this is a change, so they now heed user-specified $IMGOPTS.
Some of those tests do not work with all image options, though, so we
need to disable them accordingly.
Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-id: 20191107163708.833192-12-mreitz@redhat.com Signed-off-by: Max Reitz <mreitz@redhat.com>
Max Reitz [Thu, 7 Nov 2019 16:36:55 +0000 (17:36 +0100)]
iotests: Add -o and --no-opts to _make_test_img
Blindly overriding IMGOPTS is suboptimal as this discards user-specified
options. Whatever options the test needs should simply be appended.
Some tests do this (with IMGOPTS=$(_optstr_add "$IMGOPTS" "...")), but
that is cumbersome. It’s simpler to just give _make_test_img an -o
parameter with which tests can add options.
Some tests actually must override the user-specified options, though,
for example when creating an image in a different format than the test
$IMGFMT. For such cases, --no-opts allows clearing the current option
list.
Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-id: 20191107163708.833192-10-mreitz@redhat.com Signed-off-by: Max Reitz <mreitz@redhat.com>
Max Reitz [Thu, 7 Nov 2019 16:36:53 +0000 (17:36 +0100)]
iotests: Drop compat=1.1 in 050
IMGOPTS can never be empty for qcow2, because the check scripts adds
compat=1.1 unless the user specified any compat option themselves.
Thus, this block does not do anything and can be dropped.
Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-id: 20191107163708.833192-8-mreitz@redhat.com Signed-off-by: Max Reitz <mreitz@redhat.com>
Max Reitz [Thu, 7 Nov 2019 16:36:52 +0000 (17:36 +0100)]
iotests: Replace IMGOPTS by _unsupported_imgopts
Some tests require compat=1.1 and thus set IMGOPTS='compat=1.1'
globally. That is not how it should be done; instead, they should
simply set _unsupported_imgopts to compat=0.10 (compat=1.1 is the
default anyway).
This makes the tests heed user-specified $IMGOPTS. Some do not work
with all image options, though, so we need to disable them accordingly.
Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Maxim Levitsky <mlevitsky@redhat.com>
Message-id: 20191107163708.833192-7-mreitz@redhat.com Signed-off-by: Max Reitz <mreitz@redhat.com>
Max Reitz [Thu, 7 Nov 2019 16:36:51 +0000 (17:36 +0100)]
iotests: Filter refcount_order in 036
This test can run just fine with other values for refcount_bits, so we
should filter the value from qcow2.py's dump-header. In fact, we can
filter everything but the feature bits and header extensions, because
that is what the test is about.
(036 currently ignores user-specified image options, but that will be
fixed in the next patch.)
Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-id: 20191107163708.833192-6-mreitz@redhat.com Signed-off-by: Max Reitz <mreitz@redhat.com>
qcow2_can_store_new_dirty_bitmap works wrong, as it considers only
bitmaps already stored in the qcow2 image and ignores persistent
BdrvDirtyBitmap objects.
So, let's instead count persistent BdrvDirtyBitmaps. We load all qcow2
bitmaps on open, so there should not be any bitmap in the image for
which we don't have BdrvDirtyBitmaps version. If it is - it's a kind of
corruption, and no reason to check for corruptions here (open() and
close() are better places for it).
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20191014115126.15360-2-vsementsov@virtuozzo.com Reviewed-by: Max Reitz <mreitz@redhat.com> Cc: qemu-stable@nongnu.org Signed-off-by: Max Reitz <mreitz@redhat.com>
PanNengyuan [Wed, 27 Nov 2019 06:20:14 +0000 (14:20 +0800)]
throttle-groups: fix memory leak in throttle_group_set_limit:
This avoid a memory leak when qom-set is called to set throttle_group
limits, here is an easy way to reproduce:
1. run qemu-iotests as follow and check the result with asan:
./check -qcow2 184
Following is the asan output backtrack:
Direct leak of 912 byte(s) in 3 object(s) allocated from:
#0 0xffff8d7ab3c3 in __interceptor_calloc (/lib64/libasan.so.4+0xd33c3)
#1 0xffff8d4c31cb in g_malloc0 (/lib64/libglib-2.0.so.0+0x571cb)
#2 0x190c857 in qobject_input_start_struct /mnt/sdc/qemu-master/qemu-4.2.0-rc0/qapi/qobject-input-visitor.c:295
#3 0x19070df in visit_start_struct /mnt/sdc/qemu-master/qemu-4.2.0-rc0/qapi/qapi-visit-core.c:49
#4 0x1948b87 in visit_type_ThrottleLimits qapi/qapi-visit-block-core.c:3759
#5 0x17e4aa3 in throttle_group_set_limits /mnt/sdc/qemu-master/qemu-4.2.0-rc0/block/throttle-groups.c:900
#6 0x1650eff in object_property_set /mnt/sdc/qemu-master/qemu-4.2.0-rc0/qom/object.c:1272
#7 0x1658517 in object_property_set_qobject /mnt/sdc/qemu-master/qemu-4.2.0-rc0/qom/qom-qobject.c:26
#8 0x15880bb in qmp_qom_set /mnt/sdc/qemu-master/qemu-4.2.0-rc0/qom/qom-qmp-cmds.c:74
#9 0x157e3e3 in qmp_marshal_qom_set qapi/qapi-commands-qom.c:154
Max Reitz [Fri, 8 Nov 2019 12:34:55 +0000 (13:34 +0100)]
iotests: Add test for failing mirror complete
Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Tested-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20191108123455.39445-6-mreitz@redhat.com Signed-off-by: Max Reitz <mreitz@redhat.com>
Max Reitz [Fri, 8 Nov 2019 12:34:54 +0000 (13:34 +0100)]
iotests: Add @error to wait_until_completed
Callers can use this new parameter to expect failure during the
completion process.
Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: John Snow <jsnow@redhat.com> Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20191108123455.39445-5-mreitz@redhat.com Signed-off-by: Max Reitz <mreitz@redhat.com>
Max Reitz [Fri, 8 Nov 2019 12:34:53 +0000 (13:34 +0100)]
blkdebug: Allow taking/unsharing permissions
Sometimes it is useful to be able to add a node to the block graph that
takes or unshare a certain set of permissions for debugging purposes.
This patch adds this capability to blkdebug.
(Note that you cannot make blkdebug release or share permissions that it
needs to take or cannot share, because this might result in assertion
failures in the block layer. But if the blkdebug node has no parents,
it will not take any permissions and share everything by default, so you
can then freely choose what permissions to take and share.)
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191108123455.39445-4-mreitz@redhat.com Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Signed-off-by: Max Reitz <mreitz@redhat.com>
Max Reitz [Fri, 8 Nov 2019 12:34:52 +0000 (13:34 +0100)]
block: Use bdrv_qapi_perm_to_blk_perm()
We can save some LoC in xdbg_graph_add_edge() by using
bdrv_qapi_perm_to_blk_perm().
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191108123455.39445-3-mreitz@redhat.com Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Signed-off-by: Max Reitz <mreitz@redhat.com>
Max Reitz [Fri, 8 Nov 2019 12:34:51 +0000 (13:34 +0100)]
block: Add bdrv_qapi_perm_to_blk_perm()
We need some way to correlate QAPI BlockPermission values with
BLK_PERM_* flags. We could:
(1) have the same order in the QAPI definition as the the BLK_PERM_*
flags are in LSb-first order. However, then there is no guarantee
that they actually match (e.g. when someone modifies the QAPI schema
without thinking of the BLK_PERM_* definitions).
We could add static assertions, but these would break what’s good
about this solution, namely its simplicity.
(2) define the BLK_PERM_* flags based on the BlockPermission values.
But this way whenever someone were to modify the QAPI order
(perfectly sensible in theory), the BLK_PERM_* values would change.
Because these values are used for file locking, this might break
file locking between different qemu versions.
Therefore, go the slightly more cumbersome way: Add a function to
translate from the QAPI constants to the BLK_PERM_* flags.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191108123455.39445-2-mreitz@redhat.com Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Signed-off-by: Max Reitz <mreitz@redhat.com>
Volker Rümelin [Thu, 19 Dec 2019 20:34:05 +0000 (21:34 +0100)]
audio: fix integer overflow
Tell the compiler to do a 32bit * 32bit -> 64bit multiplication
because period_ticks is a 64bit variable. The overflow occurs
for audio timer periods larger than 4294967us.
Volker Rümelin [Sat, 4 Jan 2020 09:11:21 +0000 (10:11 +0100)]
paaudio: try to drain the recording stream
There is no guarantee a single call to pa_stream_peek every
timer_period microseconds can read a recording stream faster
than the data gets produced at the source. Let qpa_read try to
drain the recording stream.
To reproduce the problem:
Start qemu with -audiodev pa,id=audio0,in.mixing-engine=off
On the host connect the qemu recording stream to the monitor of
a hardware output device. While the problem can also be seen
with a hardware input device, it's obvious with the monitor of
a hardware output device.
In the guest start audio recording with audacity and notice the
slow recording data rate.
Volker Rümelin [Sat, 4 Jan 2020 09:11:20 +0000 (10:11 +0100)]
paaudio: drop recording stream in qpa_fini_in
Every call to pa_stream_peek which returns a data length > 0
should have a corresponding pa_stream_drop. A call to qpa_read
does not necessarily call pa_stream_drop immediately after a
call to pa_stream_peek. Test in qpa_fini_in if a last
pa_stream_drop is needed.
This prevents following messages in the libvirt log file after
a recording stream gets closed and a new one opened.
pulseaudio: pa_stream_drop failed
pulseaudio: Reason: Bad state
pulseaudio: pa_stream_drop failed
pulseaudio: Reason: Bad state
To reproduce start qemu with
-audiodev pa,id=audio0,in.mixing-engine=off
and in the guest start and stop Audacity several times.
Volker Rümelin [Sat, 4 Jan 2020 09:11:18 +0000 (10:11 +0100)]
hda-codec: fix playback rate control
Since commit 1930616b98 "audio: make mixeng optional" the
function hda_audio_output_cb can no longer assume the function
parameter avail contains the free buffer size. With the playback
mixing-engine turned off this leads to a broken playback rate
control and playback buffer drops in regular intervals.
This patch moves down the rate calculation, so the correct
buffer fill level is used for the calculation.
Peter Maydell [Fri, 3 Jan 2020 18:50:33 +0000 (18:50 +0000)]
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20191220' into staging
target-arm queue:
* Support emulating the generic timers at frequencies other than 62.5MHz
* Various fixes for SMMUv3 emulation bugs
* Improve assert error message for hflags mismatches
* arm-powerctl: rebuild hflags after setting CP15 bits in arm_set_cpu_on()
* remotes/pmaydell/tags/pull-target-arm-20191220:
arm/arm-powerctl: rebuild hflags after setting CP15 bits in arm_set_cpu_on()
target/arm: Display helpful message when hflags mismatch
hw/arm/smmuv3: Report F_STE_FETCH fault address in correct word position
hw/arm/smmuv3: Use correct bit positions in EVT_SET_ADDR2 macro
hw/arm/smmuv3: Align stream table base address to table size
hw/arm/smmuv3: Check stream IDs against actual table LOG2SIZE
hw/arm/smmuv3: Correct SMMU_BASE_ADDR_MASK value
hw/arm/smmuv3: Apply address mask to linear strtab base address
ast2600: Configure CNTFRQ at 1125MHz
target/arm: Prepare generic timer for per-platform CNTFRQ
target/arm: Abstract the generic timer frequency
target/arm: Remove redundant scaling of nexttick
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a helper function to match qemu_open() which may return files
under the /dev/fdset prefix. Those shouldn't be removed, since it's
only a qemu namespace.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
screendump: replace FILE with QIOChannel and fix close()/qemu_close()
The file opened for ppm_save() may be a /dev/fdset, in which case a
dup fd is added to the fdset. It should be removed by calling
qemu_close(), instead of the implicit close() on fclose().
I don't see a convenient way to solve that with stdio streams, so I
switched the code to QIOChannel which uses qemu_close().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Add a function to be called when a graphic update is done.
Declare the QXL renderer as async: render_update_cookie_num counts the
number of outstanding updates, and graphic_hw_update_done() is called
when it reaches none.
(note: this is preliminary work for asynchronous screendump support)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Reviewed-by: Gerd Hoffmann <kraxel@redhat.com> Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Peter Maydell [Fri, 20 Dec 2019 18:25:32 +0000 (18:25 +0000)]
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches:
- qemu-img: fix info --backing-chain --image-opts
- Error out on image creation with conflicting size options
- Fix external snapshot with VM state
- hmp: Allow using qdev ID for qemu-io command
- Misc code cleanup
- Many iotests improvements
# gpg: Signature made Thu 19 Dec 2019 17:23:11 GMT
# gpg: using RSA key 7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (30 commits)
iotests: Test external snapshot with VM state
hmp: Allow using qdev ID for qemu-io command
block: Activate recursively even for already active nodes
iotests: 211: Remove duplication with VM.blockdev_create()
iotests: 207: Remove duplication with VM.blockdev_create()
iotests: 266: Convert to VM.blockdev_create()
iotests: 237: Convert to VM.blockdev_create()
iotests: 213: Convert to VM.blockdev_create()
iotests: 212: Convert to VM.blockdev_create()
iotests: 210: Convert to VM.blockdev_create()
iotests: 206: Convert to VM.blockdev_create()
iotests: 255: Drop blockdev_create()
iotests: Create VM.blockdev_create()
qcow2: Move error check of local_err near its assignment
iotests: Fix IMGOPTSSYNTAX for nbd
iotests/273: Filter format-specific information
iotests: Add more "_require_drivers" checks to the shell-based tests
MAINTAINERS: fix qcow2-bitmap.c under Dirty Bitmaps header
qcow2: Use offset_into_cluster()
iotests: Support job-complete in run_job()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Eduardo Habkost [Wed, 16 Oct 2019 22:42:37 +0000 (19:42 -0300)]
configure: Require Python >= 3.5
Python 3.5 is the oldest Python version available on our
supported build platforms, and Python 2 end of life will be 3
weeks after the planned release date of QEMU 4.2.0. Drop Python
2 support from configure completely, and require Python 3.5 or
newer.
* remotes/cohuck/tags/s390x-20191219:
s390x: Properly fetch and test the short psw on diag308 subc 0/1
pc-bios/s390: Update firmware images
pc-bios/s390x: Fix reset psw mask
tests/boot-sector: Fix the bad s390x assembler code
target/s390x: Implement LOAD/STORE TO REAL ADDRESS inline
target/s390x: Split out helper_per_store_real
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Niek Linnenbank [Fri, 20 Dec 2019 14:03:00 +0000 (14:03 +0000)]
arm/arm-powerctl: rebuild hflags after setting CP15 bits in arm_set_cpu_on()
After setting CP15 bits in arm_set_cpu_on() the cached hflags must
be rebuild to reflect the changed processor state. Without rebuilding,
the cached hflags would be inconsistent until the next call to
arm_rebuild_hflags(). When QEMU is compiled with debugging enabled
(--enable-debug), this problem is captured shortly after the first
call to arm_set_cpu_on() for CPUs running in ARM 32-bit non-secure mode:
Simon Veith [Fri, 20 Dec 2019 14:03:00 +0000 (14:03 +0000)]
hw/arm/smmuv3: Report F_STE_FETCH fault address in correct word position
The smmuv3_record_event() function that generates the F_STE_FETCH error
uses the EVT_SET_ADDR macro to record the fetch address, placing it in
32-bit words 4 and 5.
The correct position for this address is in words 6 and 7, per the
SMMUv3 Architecture Specification.
Update the function to use the EVT_SET_ADDR2 macro instead, which is the
macro intended for writing to these words.
ref. ARM IHI 0070C, section 7.3.4.
Signed-off-by: Simon Veith <sveith@amazon.de> Acked-by: Eric Auger <eric.auger@redhat.com> Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-7-git-send-email-sveith@amazon.de Cc: Eric Auger <eric.auger@redhat.com> Cc: qemu-devel@nongnu.org Cc: qemu-arm@nongnu.org Acked-by: Eric Auger <eric.auger@redhat.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Simon Veith [Fri, 20 Dec 2019 14:03:00 +0000 (14:03 +0000)]
hw/arm/smmuv3: Use correct bit positions in EVT_SET_ADDR2 macro
The bit offsets in the EVT_SET_ADDR2 macro do not match those specified
in the ARM SMMUv3 Architecture Specification. In all events that use
this macro, e.g. F_WALK_EABT, the faulting fetch address or IPA actually
occupies the 32-bit words 6 and 7 in the event record contiguously, with
the upper and lower unused bits clear due to alignment or maximum
supported address bits. How many bits are clear depends on the
individual event type.
Update the macro to write to the correct words in the event record so
that guest drivers can obtain accurate address information on events.
ref. ARM IHI 0070C, sections 7.3.12 through 7.3.16.
Signed-off-by: Simon Veith <sveith@amazon.de> Acked-by: Eric Auger <eric.auger@redhat.com> Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-6-git-send-email-sveith@amazon.de Cc: Eric Auger <eric.auger@redhat.com> Cc: qemu-devel@nongnu.org Cc: qemu-arm@nongnu.org Acked-by: Eric Auger <eric.auger@redhat.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Simon Veith [Fri, 20 Dec 2019 14:03:00 +0000 (14:03 +0000)]
hw/arm/smmuv3: Align stream table base address to table size
Per the specification, and as observed in hardware, the SMMUv3 aligns
the SMMU_STRTAB_BASE address to the size of the table by masking out the
respective least significant bits in the ADDR field.
Apply this masking logic to our smmu_find_ste() lookup function per the
specification.
ref. ARM IHI 0070C, section 6.3.23.
Signed-off-by: Simon Veith <sveith@amazon.de> Acked-by: Eric Auger <eric.auger@redhat.com> Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-5-git-send-email-sveith@amazon.de Cc: Eric Auger <eric.auger@redhat.com> Cc: qemu-devel@nongnu.org Cc: qemu-arm@nongnu.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Simon Veith [Fri, 20 Dec 2019 14:03:00 +0000 (14:03 +0000)]
hw/arm/smmuv3: Check stream IDs against actual table LOG2SIZE
When checking whether a stream ID is in range of the stream table, we
have so far been only checking it against our implementation limit
(SMMU_IDR1_SIDSIZE). However, the guest can program the
STRTAB_BASE_CFG.LOG2SIZE field to a size that is smaller than this
limit.
Check the stream ID against this limit as well to match the hardware
behavior of raising C_BAD_STREAMID events in case the limit is exceeded.
Also, ensure that we do not go one entry beyond the end of the table by
checking that its index is strictly smaller than the table size.
ref. ARM IHI 0070C, section 6.3.24.
Signed-off-by: Simon Veith <sveith@amazon.de> Acked-by: Eric Auger <eric.auger@redhat.com> Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-4-git-send-email-sveith@amazon.de Cc: Eric Auger <eric.auger@redhat.com> Cc: qemu-devel@nongnu.org Cc: qemu-arm@nongnu.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Simon Veith [Fri, 20 Dec 2019 14:03:00 +0000 (14:03 +0000)]
hw/arm/smmuv3: Correct SMMU_BASE_ADDR_MASK value
There are two issues with the current value of SMMU_BASE_ADDR_MASK:
- At the lower end, we are clearing bits [4:0]. Per the SMMUv3 spec,
we should also be treating bit 5 as zero in the base address.
- At the upper end, we are clearing bits [63:48]. Per the SMMUv3 spec,
only bits [63:52] must be explicitly treated as zero.
Update the SMMU_BASE_ADDR_MASK value to mask out bits [63:52] and [5:0].
ref. ARM IHI 0070C, section 6.3.23.
Signed-off-by: Simon Veith <sveith@amazon.de> Acked-by: Eric Auger <eric.auger@redhat.com> Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-3-git-send-email-sveith@amazon.de Cc: Eric Auger <eric.auger@redhat.com> Cc: qemu-devel@nongnu.org Cc: qemu-arm@nongnu.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Simon Veith [Fri, 20 Dec 2019 14:03:00 +0000 (14:03 +0000)]
hw/arm/smmuv3: Apply address mask to linear strtab base address
In the SMMU_STRTAB_BASE register, the stream table base address only
occupies bits [51:6]. Other bits, such as RA (bit [62]), must be masked
out to obtain the base address.
The branch for 2-level stream tables correctly applies this mask by way
of SMMU_BASE_ADDR_MASK, but the one for linear stream tables does not.
Apply the missing mask in that case as well so that the correct stream
base address is used by guests which configure a linear stream table.
Linux guests are unaffected by this change because they choose a 2-level
stream table layout for the QEMU SMMUv3, based on the size of its stream
ID space.
ref. ARM IHI 0070C, section 6.3.23.
Signed-off-by: Simon Veith <sveith@amazon.de> Acked-by: Eric Auger <eric.auger@redhat.com> Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-2-git-send-email-sveith@amazon.de Cc: Eric Auger <eric.auger@redhat.com> Cc: qemu-devel@nongnu.org Cc: qemu-arm@nongnu.org Acked-by: Eric Auger <eric.auger@redhat.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Andrew Jeffery [Fri, 20 Dec 2019 14:03:00 +0000 (14:03 +0000)]
ast2600: Configure CNTFRQ at 1125MHz
This matches the configuration set by u-boot on the AST2600.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Reviewed-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 080ca1267a09381c43cf3c50d434fb6c186f2b6e.1576215453.git-series.andrew@aj.id.au Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Andrew Jeffery [Fri, 20 Dec 2019 14:02:59 +0000 (14:02 +0000)]
target/arm: Prepare generic timer for per-platform CNTFRQ
The ASPEED AST2600 clocks the generic timer at the rate of HPLL. On
recent firmwares this is at 1125MHz, which is considerably quicker than
the assumed 62.5MHz of the current generic timer implementation. The
delta between the value as read from CNTFRQ and the true rate of the
underlying QEMUTimer leads to sticky behaviour in AST2600 guests.
Add a feature-gated property exposing CNTFRQ for ARM CPUs providing the
generic timer. This allows platforms to configure CNTFRQ (and the
associated QEMUTimer) to the appropriate frequency prior to starting the
guest.
As the platform can now determine the rate of CNTFRQ we're exposed to
limitations of QEMUTimer that didn't previously materialise: In the
course of emulation we need to arbitrarily and accurately convert
between guest ticks and time, but we're constrained by QEMUTimer's use
of an integer scaling factor. The effect is QEMUTimer cannot exactly
capture the period of frequencies that do not cleanly divide
NANOSECONDS_PER_SECOND for scaling ticks to time. As such, provide an
equally inaccurate scaling factor for scaling time to ticks so at least
a self-consistent inverse relationship holds.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: a22db9325f96e39f76e3c2baddcb712149f46bf2.1576215453.git-series.andrew@aj.id.au Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Andrew Jeffery [Fri, 20 Dec 2019 14:02:59 +0000 (14:02 +0000)]
target/arm: Abstract the generic timer frequency
Prepare for SoCs such as the ASPEED AST2600 whose firmware configures
CNTFRQ to values significantly larger than the static 62.5MHz value
currently derived from GTIMER_SCALE. As the OS potentially derives its
timer periods from the CNTFRQ value the lack of support for running
QEMUTimers at the appropriate rate leads to sticky behaviour in the
guest.
Substitute the GTIMER_SCALE constant with use of a helper to derive the
period from gt_cntfrq_hz stored in struct ARMCPU. Initially set
gt_cntfrq_hz to the frequency associated with GTIMER_SCALE so current
behaviour is maintained.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 40bd8df043f66e1ccfb3e9482999d099ac72bb2e.1576215453.git-series.andrew@aj.id.au Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Andrew Jeffery [Fri, 20 Dec 2019 14:02:59 +0000 (14:02 +0000)]
target/arm: Remove redundant scaling of nexttick
The corner-case codepath was adjusting nexttick such that overflow
wouldn't occur when timer_mod() scaled the value back up. Remove a use
of GTIMER_SCALE and avoid unnecessary operations by calling
timer_mod_ns() directly.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: f8c680720e3abe55476e6d9cb604ad27fdbeb2e0.1576215453.git-series.andrew@aj.id.au Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell [Fri, 20 Dec 2019 14:00:49 +0000 (14:00 +0000)]
Merge remote-tracking branch 'remotes/stsquad/tags/pull-tesing-and-misc-191219-1' into staging
Various testing and logging updates
- test tci with Travis
- enable multiarch testing in Travis
- default to out-of-tree builds
- make changing logfile safe via RCU
- remove redundant tests
- remove gtester test from docker
- convert DEBUG_MMAP to tracepoints
- remove hand rolled glob function
- trigger tcg re-configure when needed
# gpg: Signature made Thu 19 Dec 2019 08:24:08 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-tesing-and-misc-191219-1: (25 commits)
tests/tcg: ensure we re-configure if configure.sh is updated
trace: replace hand-crafted pattern_glob with g_pattern_match_simple
linux-user: convert target_munmap debug to a tracepoint
linux-user: log page table changes under -d page
linux-user: add target_mmap_complete tracepoint
linux-user: convert target_mmap debug to tracepoint
linux-user: convert target_mprotect debug to tracepoint
travis.yml: Remove the redundant clang-with-MAIN_SOFTMMU_TARGETS entry
docker: gtester is no longer used
Added tests for close and change of logfile.
Add use of RCU for qemu_logfile.
qemu_log_lock/unlock now preserves the qemu_logfile handle.
Add a mutex to guarantee single writer to qemu_logfile handle.
Cleaned up flow of code in qemu_set_log(), to simplify and clarify.
Fix double free issue in qemu_set_log_filename().
ci: build out-of-tree
travis.yml: Enable builds on arm64, ppc64le and s390x
tests/test-util-filemonitor: Skip test on non-x86 Travis containers
tests/hd-geo-test: Skip test when images can not be created
iotests: Skip test 079 if it is not possible to create large files
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* remotes/vivier2/tags/trivial-branch-pull-request:
qemu-doc: Remove the unused "Guest Agent" node
Revert "qemu-options.hx: Update for reboot-timeout parameter"
target/sparc: Remove old TODO file
test-keyval: Tighten test of trailing crap after size
util/cutils: Turn FIXME comment into QEMU_BUILD_BUG_ON()
monitor: Remove unused define
MAINTAINERS: Add hw/sd/ssi-sd.c in the SD section
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell [Fri, 20 Dec 2019 11:20:25 +0000 (11:20 +0000)]
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* More uses of RCU_READ_LOCK_GUARD (Dave, myself)
* QOM doc improvments (Greg)
* Cleanups from the Meson conversion (Marc-André)
* Support for multiple -accel options (myself)
* Many x86 machine cleanup (Philippe, myself)
* tests/migration-test cleanup (Juan)
* PC machine removal and next round of deprecation (Thomas)
* kernel-doc integration (Peter, myself)
* remotes/bonzini/tags/for-upstream: (87 commits)
vga: cleanup mapping of VRAM for non-PCI VGA
hw/display: Remove "rombar" hack from vga-pci and vmware_vga
hw/pci: Remove the "command_serr_enable" property
hw/audio: Remove the "use_broken_id" hack from the AC97 device
hw/i386: Remove the deprecated machines 0.12 up to 0.15
hw/pci-host: Add Kconfig entry to select the IGD Passthrough Host Bridge
hw/pci-host/i440fx: Extract the IGD passthrough host bridge device
hw/pci-host/i440fx: Use definitions instead of magic values
hw/pci-host/i440fx: Use size_t to iterate over ARRAY_SIZE()
hw/pci-host/i440fx: Extract PCII440FXState to "hw/pci-host/i440fx.h"
hw/pci-host/i440fx: Correct the header description
Fix some comment spelling errors.
target/i386: remove unused pci-assign codes
WHPX: refactor load library
migration: check length directly to make sure the range is aligned
memory: include MemoryListener documentation and some missing function parameters
docs: add memory API reference
memory.h: Silence kernel-doc complaints
docs: Create bitops.rst as example of kernel-docs
bitops.h: Silence kernel-doc complaints
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Igor Mammedov [Thu, 12 Dec 2019 12:48:56 +0000 (13:48 +0100)]
numa: properly check if numa is supported
Commit aa57020774b, by mistake used MachineClass::numa_mem_supported
to check if NUMA is supported by machine and also as unrelated change
set it to true for sbsa-ref board.
Luckily change didn't break machines that support NUMA, as the field
is set to true for them.
But the field is not intended for checking if NUMA is supported and
will be flipped to false within this release for new machine types.
Fix it:
- by using previously used condition
!mc->cpu_index_to_instance_props || !mc->get_default_cpu_node_id
the first time and then use MachineState::numa_state down the road
to check if NUMA is supported
- dropping stray sbsa-ref chunk
Eduardo Habkost [Thu, 5 Dec 2019 22:33:39 +0000 (19:33 -0300)]
i386: Resolve CPU models to v1 by default
When using `query-cpu-definitions` using `-machine none`,
QEMU is resolving all CPU models to their latest versions. The
actual CPU model version being used by another machine type (e.g.
`pc-q35-4.0`) might be different.
In theory, this was OK because the correct CPU model
version is returned when using the correct `-machine` argument.
Except that in practice, this breaks libvirt expectations:
libvirt always use `-machine none` when checking if a CPU model
is runnable, because runnability is not expected to be affected
when the machine type is changed.
For example, when running on a Haswell host without TSX,
Haswell-v4 is runnable, but Haswell-v1 is not. On those hosts,
`query-cpu-definitions` says Haswell is runnable if using
`-machine none`, but Haswell is actually not runnable using any
of the `pc-*` machine types (because they resolve Haswell to
Haswell-v1). In other words, we're breaking the "runnability
guarantee" we promised to not break for a few releases (see
qemu-deprecated.texi).
To address this issue, change the default CPU model version to v1
on all machine types, so we make `query-cpu-definitions` output
when using `-machine none` match the results when using `pc-*`.
This will change in the future (the plan is to always return the
latest CPU model version if using `-machine none`), but only
after giving libvirt the opportunity to adapt.
Kevin Wolf [Tue, 17 Dec 2019 14:18:58 +0000 (15:18 +0100)]
iotests: Test external snapshot with VM state
This tests creating an external snapshot with VM state (which results in
an active overlay over an inactive backing file, which is also the root
node of an inactive BlockBackend), re-activating the images and
performing some operations to test that the re-activation worked as
intended.
projects / qemu-xen.git / log