* pci/host-designware:
PCI: dwc: Clear MSI interrupt status after it is handled, not before
PCI: qcom: Allow ->post_init() to fail
PCI: qcom: Don't unroll init if ->init() fails
PCI: dwc: designware: Handle ->host_init() failures
PCI: dwc: designware: Test PCIE_ATU_ENABLE bit specifically
PCI: dwc: designware: Make dw_pcie_prog_*_atu_unroll() static
PCI: iproc: Rename PCI_EXP_CAP to IPROC_PCI_EXP_CAP
PCI_EXP_CAP is an iProc-specific value, so rename it to IPROC_PCI_EXP_CAP
to make it obvious that it's not related to the generic values like
PCI_EXP_RTCTL, etc. No functional change intended.
Oza Pawandeep [Mon, 28 Aug 2017 21:43:35 +0000 (16:43 -0500)]
PCI: iproc: Add 500ms delay during device shutdown
During soft reset (e.g., "reboot" from Linux) on some iProc-based SOCs, the
LCPLL clock and PERST both go off simultaneously. This seems in accordance
with the PCIe Card Electromechanical spec, r2.0, sec 2.2.3, which says the
clock goes inactive after PERST# goes active, but doesn't specify how long
the clock should be valid after PERST#.
However, we have observed that with the iProc Stingray, some Intel NVMe
endpoints, e.g., the P3700 400GB series, are not detected correctly upon
the next boot sequence unless the clock remains valid for some time after
PERST# is asserted.
Delay 500ms after asserting PERST# before performing a reboot. The 500ms
is experimentally determined.
Signed-off-by: Oza Pawandeep <oza.oza@broadcom.com>
[bhelgaas: changelog, add spec reference, fold in iproc_pcie_shutdown()
export from Arnd Bergmann <arnd@arndb.de>] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Oza Pawandeep [Mon, 28 Aug 2017 21:43:30 +0000 (16:43 -0500)]
PCI: iproc: Work around Stingray CRS defects
Configuration Request Retry Status ("CRS") completions are a required part
of PCIe. A PCIe device may respond to config a request with a CRS
completion to indicate that it needs more time to initialize. A Root Port
that receives a CRS completion may automatically retry the request, or it
may treat the request as a failed transaction. For a failed read, it will
likely synthesize all 1's data, i.e., 0xffffffff, to complete the read to
the CPU.
CRS Software Visibility ("CRS SV") is an optional feature. Per PCIe r3.1,
sec 2.3.2, if supported and enabled, a Root Port that receives a CRS
completion for a config read of the Vendor ID will synthesize 0x0001 data
(an invalid Vendor ID) instead of retrying or failing the transaction. The
0x0001 data makes the CRS completion visible to software, so it can perform
other tasks while waiting for the device.
The iProc "Stingray" PCIe controller does not support CRS completions
correctly. From the Stingray PCIe Controller spec:
4.7.3.3. Retry Status On Configuration Cycle
Endpoints are allowed to generate retry status on configuration cycles.
In this case, the RC needs to re-issue the request. The IP does not
handle this because the number of configuration cycles needed will
probably be less than the total number of non-posted operations needed.
When a retry status is received on the User RX interface for a
configuration request that was sent on the User TX interface, it will be
indicated with a completion with the CMPL_STATUS field set to 2=CRS, and
the user will have to find the address and data values and send a new
transaction on the User TX interface. When the internal configuration
space returns a retry status during a configuration cycle (user_cscfg =
1) on the Command/Status interface, the pcie_cscrs will assert with the
pcie_csack signal to indicate the CRS status.
When the CRS Software Visibility Enable register in the Root Control
register is enabled, the IP will return the data value to 0x0001 for the
Vendor ID value and 0xffff (all 1’s) for the rest of the data in the
request for reads of offset 0 that return with CRS status. This is true
for both the User RX Interface and for the Command/Status interface.
When CRS Software Visibility is enabled, the CMPL_STATUS field of the
completion on the User RX Interface will not be 2=CRS and the pcie_cscrs
signal will not assert on the Command/Status interface.
The Stingray hardware never reissues configuration requests when it
receives CRS completions. Contrary to what sec 4.7.3.3 above says, when it
receives a CRS completion, it synthesizes 0xffff0001 data regardless of the
address of the read or the value of the CRS SV enable bit.
This is broken in two ways:
1) When CRS SV is disabled, the Root Port should never synthesize the
0x0001 value. If it receives a CRS completion, it should fail the
transaction and synthesize all 1's data.
2) When CRS SV is enabled, the Root Port should only synthesize 0x0001
data if it receives a CRS completion for a read of the Vendor ID. If it
receives a CRS completion for any other read, it should fail the
transaction and synthesize all 1's data.
This breaks pci_flr_wait(), which reads the Command register and expects to
see all 1's data if the read fails because of CRS completions. On
Stingray, it sees the incorrect 0xffff0001 data instead.
It also breaks config registers that contain the 0xffff0001 value. If we
read such a register, software can't distinguish a CRS completion from the
actual value read from the device.
On Stingray, if we read 0xffff0001 data, assume this indicates a CRS
completion and retry the read for 500ms. If we time out, return all 1's
(0xffffffff) data. Note that this corrupts registers that happen to
contain 0xffff0001.
Stingray advertises CRS SV support in its Root Capabilities register, and
the CRS SV enable bit is writable (even though the hardware ignores it).
Mask out PCI_EXP_RTCAP_CRSVIS so software doesn't try to use CRS SV.
Signed-off-by: Oza Pawandeep <oza.oza@broadcom.com>
[bhelgaas: changelog, add probe-time warning about corruption, don't
advertise CRS SV support, remove duplicate pci_generic_config_read32(),
fix alignment based on patch from Arnd Bergmann <arnd@arndb.de>] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Faiz Abbas [Thu, 10 Aug 2017 11:24:55 +0000 (16:54 +0530)]
PCI: dwc: Clear MSI interrupt status after it is handled, not before
If the interrupt status is cleared before it is handled, it is possible
that another interrupt will trigger while servicing the previous one. This
is causing timeouts in some wireless lan cards which use PCIe.
Clear MSI interrupt status after it gets serviced instead of before calling
generic_handler.
PCI: dra7xx: Propagate platform_get_irq() errors in dra7xx_pcie_probe()
platform_get_irq() returns an error code, but the pci-dra7xx driver ignores
it and always returns -EINVAL. This is not correct and prevents
-EPROBE_DEFER from being propagated properly.
Print and propagate the return value of platform_get_irq() on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Paul Burton [Tue, 15 Aug 2017 21:26:36 +0000 (16:26 -0500)]
PCI: faraday: Use PCI_NUM_INTX
Use the PCI_NUM_INTX macro to indicate the number of PCI INTx interrupts
rather than the magic number 4. This makes it clearer where the number
comes from & what it relates to.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Sergei Shtylyov [Sat, 15 Jul 2017 21:43:10 +0000 (00:43 +0300)]
PCI: faraday: Fix of_irq_get() error check
of_irq_get() may return a negative error number as well as 0 on failure,
while the driver only checks for 0, blithely continuing with the call to
irq_set_chained_handler_and_data() -- that function expects *unsigned int*
so should probably do nothing when a large IRQ number resulting from a
conversion of a negative error number is passed to it. The driver then
probes successfully while being only partly functional...
Check for 'irq <= 0' instead and propagate the negative error number to the
probe method -- that will allow the deferred probing as well.
Bjorn Helgaas [Tue, 15 Aug 2017 21:28:27 +0000 (16:28 -0500)]
PCI: dra7xx: Use PCI_NUM_INTX
Use the PCI_NUM_INTX macro to indicate the number of PCI INTx interrupts
rather than the magic number 4. This makes it clearer where the number
comes from & what it relates to.
Based-on-similar-patches-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Kishon Vijay Abraham I <kishon@ti.com>
Paul Burton [Tue, 15 Aug 2017 21:24:38 +0000 (16:24 -0500)]
PCI: altera: Use size=4 IRQ domain for legacy INTx
The devicetree binding documentation for the Altera PCIe controller shows
an example which uses an interrupt-map property to map PCI INTx interrupts
to hardware IRQ numbers 1-4. The driver creates an IRQ domain with size 5
in order to cover this range, with hwirq=0 left unused.
This patch cleans up this wasted IRQ domain entry, modifying the driver to
use an IRQ domain of size 4 which matches the actual number of PCI INTx
interrupts. Since the hwirq numbers 1-4 are part of the devicetree binding,
and this is considered ABI, we cannot simply change the interrupt-map
property to use the range 0-3. Instead we make use of the
pci_irqd_intx_xlate() helper function to translate the range 1-4 used at
the DT level into the range 0-3 which is now used within the driver, and
stop adding 1 to decoded hwirq numbers in altera_pcie_isr().
Whilst cleaning up INTx handling we make use of the new PCI_NUM_INTX macro
& drop the custom INTX_NUM definition.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Ley Foon Tan <lftan@altera.com>
Paul Burton [Tue, 15 Aug 2017 19:02:17 +0000 (12:02 -0700)]
PCI: Add pci_irqd_intx_xlate()
Legacy PCI INTx interrupts are represented in the PCI_INTERRUPT_PIN
register using the range 1-4, which matches our enum pci_interrupt_pin.
This is however not ideal for an IRQ domain, where with 4 interrupts we
would ideally have a domain of size 4 & hwirq numbers in the range 0-3.
Different PCI host controller drivers have handled this in different ways.
Of those under drivers/pci/ which register an INTx IRQ domain, we have:
- pcie-altera uses the range 1-4 in device trees and an IRQ domain of
size 5 to cover that range, with entry 0 wasted.
- pcie-xilinx & pcie-xilinx-nwl use the range 1-4 in device trees but
register an IRQ domain of size 4, which doesn't cover the hwirq=4/INTD
case leading to that interrupt being broken.
- pci-ftpci100 & pci-aardvark use the range 0-3 in both device trees & as
hwirq numbering in the driver & IRQ domain.
In order to introduce some level of consistency in at least the hwirq
numbering used by the drivers & IRQ domains, this patch introduces a new
pci_irqd_intx_xlate() helper function which drivers using the 1-4 range in
device trees can assign as the xlate callback for their INTx IRQ domain.
This translates the 1-4 range into a 0-3 range, allowing us to use an IRQ
domain of size 4 & avoid a wasted entry. Further patches will make use of
this in drivers to allow them to use an IRQ domain of size 4 for legacy
INTx interrupts without breaking INTD.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Paul Burton [Tue, 15 Aug 2017 19:02:16 +0000 (12:02 -0700)]
PCI: Move enum pci_interrupt_pin to linux/pci.h
We currently have a definition of enum pci_interrupt_pin in a header
specific to PCI endpoints - linux/pci-epf.h. In order to allow for use of
this enum from PCI host code in a future commit, move its definition to
linux/pci.h & include that from linux/pci-epf.h.
Additionally we add a PCI_NUM_INTX macro which indicates the number of PCI
INTx interrupts, and will be used alongside enum pci_interrupt_pin in
further patches.
The setup of MSI with Hyper-V host was sleeping with locks held. This
error is reported when doing SR-IOV hotplug with kernel built with lockdep:
BUG: sleeping function called from invalid context at kernel/sched/completion.c:93
in_atomic(): 1, irqs_disabled(): 1, pid: 1405, name: ip
3 locks held by ip/1405:
#0: (rtnl_mutex){+.+.+.}, at: [<ffffffff976b10bb>] rtnetlink_rcv+0x1b/0x40
#1: (&desc->request_mutex){+.+...}, at: [<ffffffff970ddd33>] __setup_irq+0xb3/0x720
#2: (&irq_desc_lock_class){-.-...}, at: [<ffffffff970ddd65>] __setup_irq+0xe5/0x720
irq event stamp: 3476
hardirqs last enabled at (3475): [<ffffffff971b3005>] get_page_from_freelist+0x225/0xc90
hardirqs last disabled at (3476): [<ffffffff978024e7>] _raw_spin_lock_irqsave+0x27/0x90
softirqs last enabled at (2446): [<ffffffffc05ef0b0>] ixgbevf_configure+0x380/0x7c0 [ixgbevf]
softirqs last disabled at (2444): [<ffffffffc05ef08d>] ixgbevf_configure+0x35d/0x7c0 [ixgbevf]
The workaround is to poll for host response instead of blocking on
completion.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Shawn Lin [Fri, 21 Jul 2017 01:26:06 +0000 (09:26 +0800)]
PCI: hisi: Remove unused variable driver
The local "driver" variable was unused and caused a warning, so remove it:
drivers/pci/dwc/pcie-hisi.c: In function 'hisi_pcie_probe':
drivers/pci/dwc/pcie-hisi.c:271:24: warning: variable 'driver' set but not used [-Wunused-but-set-variable]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Zhou Wang <wangzhou1@hisilicon.com> Acked-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
host_init() should detect and propagate errors from post_init().
In addition, by acknowledging that post_init() can fail we must disable the
post_init() resources in a step separate from the deinit, so that we don't
try to disable the post_init() resources a second time.
Philipp Zabel [Wed, 19 Jul 2017 15:25:56 +0000 (17:25 +0200)]
PCI: imx6: Explicitly request exclusive reset control
Commit a53e35db70d1 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls to
explicitly state whether the driver needs exclusive or shared reset control
behavior. Convert all drivers requesting exclusive resets to the explicit
API call so the temporary transition helpers can be removed.
No functional changes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Richard Zhu <hongxing.zhu@nxp.com> Cc: Lucas Stach <l.stach@pengutronix.de>
In several dwc-based drivers, ->host_init() can fail, so make sure to
propagate and handle this to avoid continuing operation of a driver or
hardware in an invalid state.
PCI: dwc: designware: Test PCIE_ATU_ENABLE bit specifically
The ATU CTRL2 register is 32 bits, and bits other than the enable bit may
be set. To check whether the ATU is enabled or not, we should test the
enable bit specifically.
Carlos Palminha [Mon, 17 Jul 2017 13:13:34 +0000 (14:13 +0100)]
PCI: dwc: designware: Make dw_pcie_prog_*_atu_unroll() static
Helper functions dw_pcie_prog_*_atu_unroll() don't need to be in global
scope, so make them static.
Cleans up sparse warnings:
- symbol 'dw_pcie_prog_outbound_atu_unroll' was not declared. Should it be static?
- symbol 'dw_pcie_prog_inbound_atu_unroll' was not declared. Should it be static?
Signed-off-by: Carlos Palminha <palminha@synopsys.com>
[bhelgaas: rewrap to fit in 80 columns] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Joao Pinto <jpinto@synopsys.com> Acked-by: Jingoo Han <jingoohan1@gmail.com>
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A small set of x86 fixes:
- prevent the kernel from using the EFI reboot method when EFI is
disabled.
- two patches addressing clang issues"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Disable the address-of-packed-member compiler warning
x86/efi: Fix reboot_mode when EFI runtime services are disabled
x86/boot: #undef memcpy() et al in string.c
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"Two patches addressing build warnings caused by inconsistent kernel
doc comments"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/wait: Clean up some documentation warnings
sched/core: Fix some documentation build warnings
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A couple of fixes for performance counters and kprobes:
- a series of small patches which make the uncore performance
counters on Skylake server systems work correctly
- add a missing instruction slot release to the failure path of
kprobes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kprobes/x86: Release insn_slot in failure path
perf/x86/intel/uncore: Fix missing marker for skx_uncore_cha_extra_regs
perf/x86/intel/uncore: Fix SKX CHA event extra regs
perf/x86/intel/uncore: Remove invalid Skylake server CHA filter field
perf/x86/intel/uncore: Fix Skylake server CHA LLC_LOOKUP event umask
perf/x86/intel/uncore: Fix Skylake server PCU PMU event format
perf/x86/intel/uncore: Fix Skylake UPI PMU event masks
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"Fix for a regression caused by the conversion of x86 to the generic
hotplug code.
Instead of doing a plain single line revert, this adds a pile of
comments so the semantics of the force argument are clear"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/cpuhotplug: Revert "Set force affinity flag on hotplug migration"
Merge tag 'devicetree-fixes-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
"Two small DT fixes:
- Fix error handling in of_irq_to_resource_table() due to
of_irq_to_resource() error return changes.
- Fix dtx_diff script due to dts include path changes"
* tag 'devicetree-fixes-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: irq: fix of_irq_to_resource() error check
scripts/dtc: dtx_diff - update include dts paths to match build
Merge tag 'nfs-for-4.13-3' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client fixes from Anna Schumaker:
"More NFS client bugfixes for 4.13.
Most of these fix locking bugs that Ben and Neil noticed, but I also
have a patch to fix one more access bug that was reported after last
week.
Stable fixes:
- Fix a race where CB_NOTIFY_LOCK fails to wake a waiter
- Invalidate file size when taking a lock to prevent corruption
Other fixes:
- Don't excessively generate tiny writes with fallocate
- Use the raw NFS access mask in nfs4_opendata_access()"
* tag 'nfs-for-4.13-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFSv4.1: Fix a race where CB_NOTIFY_LOCK fails to wake a waiter
NFS: Optimize fallocate by refreshing mapping when needed.
NFS: invalidate file size when taking a lock.
NFS: Use raw NFS access mask in nfs4_opendata_access()
Merge tag 'xfs-4.13-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
- fix firstfsb variables that we left uninitialized, which could lead
to locking problems.
- check for NULL metadata buffer pointers before using them.
- don't allow btree cursor manipulation if the btree block is corrupt.
Better to just shut down.
- fix infinite loop problems in quotacheck.
- fix buffer overrun when validating directory blocks.
- fix deadlock problem in bunmapi.
* tag 'xfs-4.13-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix multi-AG deadlock in xfs_bunmapi
xfs: check that dir block entries don't off the end of the buffer
xfs: fix quotacheck dquot id overflow infinite loop
xfs: check _alloc_read_agf buffer pointer before using
xfs: set firstfsb to NULLFSBLOCK before feeding it to _bmapi_write
xfs: check _btree_check_block value
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"s390:
- SRCU fix
PPC:
- host crash fixes
x86:
- bugfixes, including making nested posted interrupts really work
Generic:
- tweaks to kvm_stat and to uevents"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: LAPIC: Fix reentrancy issues with preempt notifiers
tools/kvm_stat: add '-f help' to get the available event list
tools/kvm_stat: use variables instead of hard paths in help output
KVM: nVMX: Fix loss of L2's NMI blocking state
KVM: nVMX: Fix posted intr delivery when vcpu is in guest mode
x86: irq: Define a global vector for nested posted interrupts
KVM: x86: do mask out upper bits of PAE CR3
KVM: make pid available for uevents without debugfs
KVM: s390: take srcu lock when getting/setting storage keys
KVM: VMX: remove unused field
KVM: PPC: Book3S HV: Fix host crash on changing HPT size
KVM: PPC: Book3S HV: Enable TM before accessing TM registers
Merge tag 'for-linus-4.13b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Three minor cleanups for xen related drivers"
* tag 'for-linus-4.13b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: dont fiddle with event channel masking in suspend/resume
xen: selfballoon: remove unnecessary static in frontswap_selfshrink()
xen: Drop un-informative message during boot
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"I'd been collecting these whilst we debugged a CPU hotplug failure,
but we ended up diagnosing that one to tglx, who has taken a fix via
the -tip tree separately.
We're seeing some NFS issues that we haven't gotten to the bottom of
yet, and we've uncovered some issues with our backtracing too so there
might be another fixes pull before we're done.
Summary:
- Ensure we have a guard page after the kernel image in vmalloc
- Fix incorrect prefetch stride in copy_page
- Ensure irqs are disabled in die()
- Fix for event group validation in QCOM L2 PMU driver
- Fix requesting of PMU IRQs on AMD Seattle
- Minor cleanups and fixes"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mmu: Place guard page after mapping of kernel image
drivers/perf: arm_pmu: Request PMU SPIs with IRQF_PER_CPU
arm64: sysreg: Fix unprotected macro argmuent in write_sysreg
perf: qcom_l2: fix column exclusion check
arm64/lib: copy_page: use consistent prefetch stride
arm64/numa: Drop duplicate message
perf: Convert to using %pOF instead of full_name
arm64: Convert to using %pOF instead of full_name
arm64: traps: disable irq in die()
arm64: atomics: Remove '&' from '+&' asm constraint in lse atomics
arm64: uaccess: Remove redundant __force from addr cast in __range_ok
Merge tag 'powerpc-4.13-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"The highlight is Ben's patch to work around a host killing bug when
running KVM guests with the Radix MMU on Power9. See the long change
log of that commit for more detail.
And then three fairly minor fixes:
- fix of_node_put() underflow during reconfig remove, using old DLPAR
tools.
- fix recently introduced ld version check with 64-bit LE-only
toolchain.
- free the subpage_prot_table correctly, avoiding a memory leak.
Thanks to: Aneesh Kumar K.V, Benjamin Herrenschmidt, Laurent Vivier"
* tag 'powerpc-4.13-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm/hash: Free the subpage_prot_table correctly
powerpc/Makefile: Fix ld version check with 64-bit LE-only toolchain
powerpc/pseries: Fix of_node_put() underflow during reconfig remove
powerpc/mm/radix: Workaround prefetch issue with KVM
NFSv4.1: Fix a race where CB_NOTIFY_LOCK fails to wake a waiter
nfs4_retry_setlk() sets the task's state to TASK_INTERRUPTIBLE within the
same region protected by the wait_queue's lock after checking for a
notification from CB_NOTIFY_LOCK callback. However, after releasing that
lock, a wakeup for that task may race in before the call to
freezable_schedule_timeout_interruptible() and set TASK_WAKING, then
freezable_schedule_timeout_interruptible() will set the state back to
TASK_INTERRUPTIBLE before the task will sleep. The result is that the task
will sleep for the entire duration of the timeout.
Since we've already set TASK_INTERRUPTIBLE in the locked section, just use
freezable_schedule_timout() instead.
Fixes: a1d617d8f134 ("nfs: allow blocking locks to be awoken by lock callbacks") Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Cc: stable@vger.kernel.org # v4.9+ Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Merge branch 'for-4.13-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Fixes addressing problems reported by users, and there's one more
regression fix"
* 'for-4.13-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: round down size diff when shrinking/growing device
Btrfs: fix early ENOSPC due to delalloc
btrfs: fix lockup in find_free_extent with read-only block groups
Btrfs: fix dir item validation when replaying xattr deletes
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md
Pull MD fixes from Shaohua Li:
"This fixes several bugs, three of them are marked for stable:
- an initialization issue fixed by Ming
- a bio clone race issue fixed by me
- an async tx flush issue fixed by Ofer
- other cleanups"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
MD: fix warnning for UP case
md/raid5: add thread_group worker async_tx_issue_pending_all
md: simplify code with bio_io_error
md/raid1: fix writebehind bio clone
md: raid1-10: move raid1/raid10 common code into raid1-10.c
md: raid1/raid10: initialize bvec table via bio_add_page()
md: remove 'idx' from 'struct resync_pages'
Merge tag 'for-4.13/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a few DM integrity fixes that improve performance. One that address
inefficiencies in the on-disk journal device layout. Another that
makes use of the block layer's on-stack plugging when writing the
journal.
- a dm-bufio fix for the blk_status_t conversion that went in during
the merge window.
- a few DM raid fixes that address correctness when suspending the
device and a validation fix for validation that occurs during device
activation.
- a couple DM zoned target fixes. Important one being the fix to not
use GFP_KERNEL in the IO path due to concerns about deadlock in
low-memory conditions (e.g. swap over a DM zoned device, etc).
- a DM DAX device fix to make sure dm_dax_flush() is called if the
underlying DAX device is operating as a write cache.
* tag 'for-4.13/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm, dax: Make sure dm_dax_flush() is called if device supports it
dm verity fec: fix GFP flags used with mempool_alloc()
dm zoned: use GFP_NOIO in I/O path
dm zoned: remove test for impossible REQ_OP_FLUSH conditions
dm raid: bump target version
dm raid: avoid mddev->suspended access
dm raid: fix activation check in validate_raid_redundancy()
dm raid: remove WARN_ON() in raid10_md_layout_to_format()
dm bufio: fix error code in dm_bufio_write_dirty_buffers()
dm integrity: test for corrupted disk format during table load
dm integrity: WARN_ON if variables representing journal usage get out of sync
dm integrity: use plugging when writing the journal
dm integrity: fix inefficient allocation of journal space
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A small collection of fixes that should go into this series. This
contains:
- NVMe pull request from Christoph, with various fixes for nvme
proper and nvme-fc.
- disable runtime PM for blk-mq for now.
With scsi now defaulting to using blk-mq, this reared its head as
an issue. Longer term we'll fix up runtime PM for blk-mq, for now
just disable it to prevent a hang on laptop resume for some folks.
- blk-mq CPU <-> hw queue map fix from Christoph.
- xen/blkfront pull request from Konrad, with two small fixes for the
blkfront driver.
- a few fixups for nbd from Joseph.
- a stable fix for pblk from Javier"
* 'for-linus' of git://git.kernel.dk/linux-block:
lightnvm: pblk: advance bio according to lba index
nvme: validate admin queue before unquiesce
nbd: clear disconnected on reconnect
nvme-pci: fix HMB size calculation
nvme-fc: revise TRADDR parsing
nvme-fc: address target disconnect race conditions in fcp io submit
nvme: fabrics commands should use the fctype field for data direction
nvme: also provide a UUID in the WWID sysfs attribute
xen/blkfront: always allocate grants first from per-queue persistent grants
xen-blkfront: fix mq start/stop race
blk-mq: map queues to all present CPUs
block: disable runtime-pm for blk-mq
xen-blkfront: Fix handling of non-supported operations
nbd: only set sndtimeo if we have a timeout set
nbd: take tx_lock before disconnecting
nbd: allow multiple disconnects to be sent
Merge tag 'mmc-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"Here are a couple of mmc fixes intended for v4.13-rc1.
I have also included a couple of cleanup patches in this pull request
for OMAP2+, related to the omap_hsmmc driver. The reason is because of
the changes are also depending on OMAP SoC specific code, so this
simplifies how to deal with this.
Summary:
MMC host:
- sunxi: Correct time phase settings
- omap_hsmmc: Clean up some dead code
- dw_mmc: Fix message printed for deprecated num-slots DT binding
- dw_mmc: Fix DT documentation"
* tag 'mmc-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
Documentation: dw-mshc: deprecate num-slots
mmc: dw_mmc: fix the wrong condition check of getting num-slots from DT
mmc: host: omap_hsmmc: remove unused platform callbacks
ARM: OMAP2+: hsmmc.c: Remove dead code
mmc: sunxi: Keep default timing phase settings for new timing mode
Javier González [Fri, 28 Jul 2017 13:13:16 +0000 (15:13 +0200)]
lightnvm: pblk: advance bio according to lba index
When a lba either hits the cache or corresponds to an empty entry in the
L2P table, we need to advance the bio according to the position in which
the lba is located. Otherwise, we will copy data in the wrong page, thus
causing data corruption for the application.
In case of a cache hit, we assumed that bio->bi_iter.bi_idx would
contain the correct index, but this is no necessarily true. Instead, use
the local bio advance counter and iterator. This guarantees that lbas
hitting the cache are copied into the right bv_page.
In case of an empty L2P entry, we omitted to advance the bio. In the
cases when the same I/O also contains a cache hit, data corresponding
to this lba will be copied to the wrong bv_page. Fix this by advancing
the bio as we do in the case of a cache hit.
Will Deacon [Mon, 24 Jul 2017 10:46:09 +0000 (11:46 +0100)]
arm64: mmu: Place guard page after mapping of kernel image
The vast majority of virtual allocations in the vmalloc region are followed
by a guard page, which can help to avoid overruning on vma into another,
which may map a read-sensitive device.
This patch adds a guard page to the end of the kernel image mapping (i.e.
following the data/bss segments).
Cc: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com>
x86/boot: Disable the address-of-packed-member compiler warning
The clang warning 'address-of-packed-member' is disabled for the general
kernel code, also disable it for the x86 boot code.
This suppresses a bunch of warnings like this when building with clang:
./arch/x86/include/asm/processor.h:535:30: warning: taking address of
packed member 'sp0' of class or structure 'x86_hw_tss' may result in an
unaligned pointer value [-Waddress-of-packed-member]
return this_cpu_read_stable(cpu_tss.x86_tss.sp0);
^~~~~~~~~~~~~~~~~~~
./arch/x86/include/asm/percpu.h:391:59: note: expanded from macro
'this_cpu_read_stable'
#define this_cpu_read_stable(var) percpu_stable_op("mov", var)
^~~
./arch/x86/include/asm/percpu.h:228:16: note: expanded from macro
'percpu_stable_op'
: "p" (&(var)));
^~~
Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Cc: Doug Anderson <dianders@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20170725215053.135586-1-mka@chromium.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Merge tag 'drm-fixes-for-v4.13-rc3' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"These iare the fixes for 4.13-rc3: vmwgfx, exynos, i915, amdgpu,
nouveau, host1x and displayport fixes.
As expected people woke up this week, i915 didn't do an -rc2 pull so
got a bumper -rc3 pull, and Ben resurfaced on nouveau and fixed a
bunch of major crashers seen on Fedora 26, and there are a few vmwgfx
fixes as well.
Otherwise exynos had some regression fixes/cleanups, and amdgpu has an
rcu locking regression fix and a couple of minor fixes"
* tag 'drm-fixes-for-v4.13-rc3' of git://people.freedesktop.org/~airlied/linux: (44 commits)
drm/i915: Fix bad comparison in skl_compute_plane_wm.
drm/i915: Force CPU synchronisation even if userspace requests ASYNC
drm/i915: Only skip updating execobject.offset after error
drm/i915: Only mark the execobject as pinned on success
drm/i915: Remove assertion from raw __i915_vma_unpin()
drm/i915/cnl: Fix loadgen select programming on ddi vswing sequence
drm/i915: Fix scaler init during CRTC HW state readout
drm/i915/selftests: Fix an error handling path in 'mock_gem_device()'
drm/i915: Unbreak gpu reset vs. modeset locking
gpu: host1x: Free the IOMMU domain when there is no device to attach
drm/i915: Fix cursor updates on some platforms
drm/i915: Fix user ptr check size in eb_relocate_vma()
drm: exynos: mark pm functions as __maybe_unused
drm/exynos: select CEC_CORE if CEC_NOTIFIER
drm/exynos/hdmi: fix disable sequence
drm/exynos: mic: add a bridge at probe
drm/exynos/dsi: Remove error handling for bridge_node DT parsing
drm/exynos: dsi: do not try to find bridge
drm: exynos: hdmi: make of_device_ids const.
drm: exynos: constify mixer_match_types and *_mxr_drv_data.
...
Dave Airlie [Fri, 28 Jul 2017 02:32:59 +0000 (12:32 +1000)]
Merge tag 'exynos-drm-fixes-for-v4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Summary:
- fix probing fail issue of dsi driver without bridge device.
- fix disable sequence of hdmi driver.
- trivial cleanups.
* tag 'exynos-drm-fixes-for-v4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm: exynos: mark pm functions as __maybe_unused
drm/exynos: select CEC_CORE if CEC_NOTIFIER
drm/exynos/hdmi: fix disable sequence
drm/exynos: mic: add a bridge at probe
drm/exynos/dsi: Remove error handling for bridge_node DT parsing
drm/exynos: dsi: do not try to find bridge
drm: exynos: hdmi: make of_device_ids const.
drm: exynos: constify mixer_match_types and *_mxr_drv_data.
exynos_drm: Clean up duplicated assignment in exynos_drm_driver
Dave Airlie [Fri, 28 Jul 2017 00:19:08 +0000 (10:19 +1000)]
Merge tag 'drm-intel-fixes-2017-07-27' of git://anongit.freedesktop.org/git/drm-intel into drm-fixes
i915 fixes for -rc3
Bit more than usual since we missed -rc2. 4x cc: stable, 2 gvt
patches, but all fairly minor stuff. Last minute rebase was to add a
few missing cc: stable, I did prep the pull this morning already and
made sure CI approves.
* tag 'drm-intel-fixes-2017-07-27' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Fix bad comparison in skl_compute_plane_wm.
drm/i915: Force CPU synchronisation even if userspace requests ASYNC
drm/i915: Only skip updating execobject.offset after error
drm/i915: Only mark the execobject as pinned on success
drm/i915: Remove assertion from raw __i915_vma_unpin()
drm/i915/cnl: Fix loadgen select programming on ddi vswing sequence
drm/i915: Fix scaler init during CRTC HW state readout
drm/i915/selftests: Fix an error handling path in 'mock_gem_device()'
drm/i915: Unbreak gpu reset vs. modeset locking
drm/i915: Fix cursor updates on some platforms
drm/i915: Fix user ptr check size in eb_relocate_vma()
drm/i915/gvt: Extend KBL platform support in GVT-g
drm/i915/gvt: Fix the vblank timer close issue after shutdown VMs in reverse
Dave Airlie [Fri, 28 Jul 2017 00:14:08 +0000 (10:14 +1000)]
Merge tag 'drm-misc-fixes-2017-07-27' of git://anongit.freedesktop.org/git/drm-misc into drm-fixes
Core Changes:
- dp: A few fixes in drm_dp_downstream_debug() (Chris)
- rockchip: sanitize the Kconfig dependencies (fallout from EXTCON) (Arnd)
- host1x: Free the iommu domain when attach_device fails (Paul)
Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Paul Kocialkowski <contact@paulk.fr>
* tag 'drm-misc-fixes-2017-07-27' of git://anongit.freedesktop.org/git/drm-misc:
gpu: host1x: Free the IOMMU domain when there is no device to attach
drm/rockchip: fix Kconfig dependencies
drm/dp: Don't trust drm_dp_downstream_id()
drm/dp: Fix read pointer for drm_dp_downsteam_debug()
Merge tag 'acpi-4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These are two fixups for the suspend-to-idle handling in the ACPI
subsystem after recent changes in that area and two simple fixes of
the ACPI NUMA code.
Specifics:
- Add an ACPI module parameter to allow users to override the new
default behavior on some systems where the EC GPE is not disabled
during suspend-to-idle in case the EC on their systems generates
excessive wakeup events and they want to sacrifice some
functionality (like power button wakeups) for extra battery life
while suspended (Rafael Wysocki).
- Fix flushing of the outstanding EC work in the ACPI core
suspend-to-idle code (Rafael Wysocki).
- Add a missing include and fix a messed-up comment in the ACPI NUMA
code (Ross Zwisler)"
* tag 'acpi-4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: NUMA: Fix typo in the full name of SRAT
ACPI: NUMA: add missing include in acpi_numa.h
ACPI / PM / EC: Flush all EC work in acpi_freeze_sync()
ACPI / EC: Add parameter to force disable the GPE on suspend
Chris Wilson [Fri, 21 Jul 2017 14:50:37 +0000 (15:50 +0100)]
drm/i915: Force CPU synchronisation even if userspace requests ASYNC
The goal here was to minimise doing any thing or any check inside the
kernel that was not strictly required. For a userspace that assumes
complete control over the cache domains, the kernel is usually using
outdated information and may trigger clflushes where none were
required.
However, swapping is a situation where userspace has no knowledge of the
domain transfer, and will leave the object in the CPU cache. The kernel
must flush this out to the backing storage prior to use with the GPU. As
we use an asynchronous task tracked by an implicit fence for this, we
also need to cancel the ASYNC flag on the object so that the object will
wait for the clflush to complete before being executed. This also absolves
userspace of the responsibility imposed by commit 77ae9957897d ("drm/i915:
Enable userspace to opt-out of implicit fencing") that its needed to ensure
that the object was out of the CPU cache prior to use on the GPU.
Fixes: 77ae9957897d ("drm/i915: Enable userspace to opt-out of implicit fencing")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101571 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Jason Ekstrand <jason@jlekstrand.net> Reviewed-by: Jason Ekstrand <jason@jlekstrand.net> Link: https://patchwork.freedesktop.org/patch/msgid/20170721145037.25105-5-chris@chris-wilson.co.uk Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 0f46daa1a273779a0b73d768a788ca3f04238f9c) Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 21 Jul 2017 14:50:36 +0000 (15:50 +0100)]
drm/i915: Only skip updating execobject.offset after error
I was being overly paranoid in not updating the execobject.offset after
performing the fallback copy where we set reloc.presumed_offset to -1.
The thinking was to ensure that a subsequent NORELOC execbuf would be
forced to process the invalid relocations. However this is overkill so
long as we *only* update the execobject.offset following a successful
update of the relocation value witin the batch. If we have to repeat the
execbuf due to a later interruption, then we may skip the relocations on
the second pass (honouring NORELOC) since the execobject.offset match
the actual offsets (even though reloc.presumed_offset is garbage).
Subsequent calls to execbuf with NORELOC should themselves ensure that
the reloc.presumed_offset have been corrected in case of future
migration.
Reporting back the actual execobject.offset, even when
reloc.presumed_offset is garbage, ensures that reuse of those objects
use the latest information to avoid relocations.
Fixes: 2889caa92321 ("drm/i915: Eliminate lots of iterations over the execobjects array")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101635 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170721145037.25105-4-chris@chris-wilson.co.uk Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 1f727d9e725a408ef58d159c20fb2e51818ff153) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 21 Jul 2017 14:50:35 +0000 (15:50 +0100)]
drm/i915: Only mark the execobject as pinned on success
If we fail to acquire a fence (for old school fenced GPU access) then we
unwind the vma reservation, including its pin. However, we were making
the execobject as holding the pin before erring out, leading to a double
unpin:
Reported-by: Tomi Sarvela <tomi.p.sarvela@intel.com> Fixes: 2889caa92321 ("drm/i915: Eliminate lots of iterations over the execobjects array") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170721145037.25105-3-chris@chris-wilson.co.uk Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 1da7b54c46bcfe5484af0b27d8c9003b238031b0) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 21 Jul 2017 14:50:34 +0000 (15:50 +0100)]
drm/i915: Remove assertion from raw __i915_vma_unpin()
After we detect a i915_vma pin overflow, we call __i915_vma_unpin to
cleanup. However, on an overflow the pin_count bitfield will be zero,
triggering an assertion, even though we the intention is to merely warn
and report the error back to the user (as historically the culprit has
be a leak in the display code).
Fixes: 20dfbde463c8 ("drm/i915: Wrap vma->pin_count accessors with small inline helpers") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170721145037.25105-2-chris@chris-wilson.co.uk Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 67fddd902b8e37b15a905c287ce4e40f52a564af) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915/cnl: Fix loadgen select programming on ddi vswing sequence
The condition for setting the Loadgen Select bit of
PORT_TX_DW4 register during DDI Vswing Sequence should be
Bit rate <=6 GHz whereas the existing code checks only
Bit Rate < 6GHz. This patch fixes this condition.
While at it also remove the redundant paranthesis.
Fixes: cf54ca8bc567 ("drm/i915/cnl: Implement voltage swing sequence.") Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Manasi Navare <manasi.d.navare@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/1500329122-32662-1-git-send-email-manasi.d.navare@intel.com Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit a8e45a1c42d11597e975f3e5f2fe182f90cdaa7f) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Thu, 20 Jul 2017 11:28:20 +0000 (14:28 +0300)]
drm/i915: Fix scaler init during CRTC HW state readout
The scaler allocation code depends on a non-zero default value for the
crtc scaler_id, so make sure we initialize the scaler state accordingly
even if the crtc is off. This fixes at least an initial YUV420 modeset
(added in a follow-up patchset by Shashank) when booting with the screen
off: after the initial HW readout and modeset which enables the scaler a
subsequent modeset will disable the scaler which isn't properly
allocated. This results in a funky HW state where the pipe scaler HW
registers can't be modified and the normally black screen is grey and
shifted to the right or jitters.
The problem was revealed by Shashank's YUV420 patchset and first
reported by Ville.
v2:
- In the stable tag also include versions which need backporting (Jani)
Cc: Jani Nikula <jani.nikula@intel.com> Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Chandra Konduru <chandra.konduru@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: <stable@vger.kernel.org> # 4.2.x Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Fixes: a1b2278e4dfc ("drm/i915: skylake panel fitting using shared scalers") Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170720112820.26816-1-imre.deak@intel.com Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 5fb9dadf336f3590c799e8cbde348215dccc2aa2) Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Wed, 19 Jul 2017 12:54:55 +0000 (14:54 +0200)]
drm/i915: Unbreak gpu reset vs. modeset locking
Taking the modeset locks unconditionally isn't the greatest idea,
because atm that part is still broken and times out (and then atomic
keels over). And there's really no reason to do so, the old code
didn't do that either.
To make the patch a bit simpler let's also nuke 2 cases that are only
around for the old mmioflip paths. Atomic nonblocking workers will not
die (minus bugs) when a gpu reset happens.
And of course this doesn't fix any of the gpu reset vs. modeset
deadlock fun, but it at least stop modern CI machines from keeling
over all over the place for no reason at all.
And we still have the explicit testcases to run the fake gpu reset, so
coverage isn't that much worse.
v2: Split out additional changes on top, restrict this to purely reducing
the critical section of modeset locks.
v2: Review from Maarten
- update comments
- don't oops when state is NULL in intel_finish_reset, but try to at
least still drop locks properly. The hw is going to be toast anyway.
Fixes: 739748939974 ("drm/i915: Fix modeset handling during gpu reset, v5.") Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170719125502.25696-3-daniel.vetter@ffwll.ch
(cherry picked from commit ce87ea15ebc60a9f8f156b2549f7b2cf7fe48d04) Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Merge branch 'parisc-4.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
- The majority of lines changed are due to regenerated defconfig files.
- The support for the Page Deallocation Table (PDT) which was merged in
the merge window for 4.13 contained a bug which crashes the kernel if
a bad page is reported by firmware. This is now fixed and the kernel
messages will show which memory slot holds the broken DIMM.
- Commit 3a166fc2d4ef ("kbuild: handle libs-y archives separately from
built-in.o archives") broke linking the parisc kernel due to
millicode symbols which can't be reached then any longer. This was
fixed by modifying the parisc vmlinux.lds linker script.
- If the stack checker panics on stack overflow, avoid recursive
panics.
- Some parisc machines can't physically power off and thus instead
start after some time to flood the console by presumably detected
soft lockups. Avoid this by disabling the lockup detectors before
entering the endless for-next loop.
- Dave Anglin provided fixes which prevents TLB speculation on flushed
pages on PA8800/PA9000 CPUs.
- Arvind Yadav sent a trivial patch to constify the attribute_group
structure in our firmware on-board-flash storage driver
(pdc_stable.c)
* 'parisc-4.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Extend disabled preemption in copy_user_page
parisc: Prevent TLB speculation on flushed pages on CPUs that only support equivalent aliases
parisc: Suspend lockup detectors before system halt
parisc: Show DIMM slot number which holds broken memory module
parisc: Add function to return DIMM slot of physical address
parisc: Fix crash when calling PDC_PAT_MEM PDT firmware function
parisc: regenerate defconfig files
parisc: pdc_stable: constify attribute_group structures.
parisc: Merge millicode routines via linker script
parisc: Disable further stack checks when panic occurs during stack check
xen: dont fiddle with event channel masking in suspend/resume
Instead of fiddling with masking the event channels during suspend
and resume handling let do the irq subsystem do its job. It will do
the mask and unmask operations as needed.
Signed-off-by: Juergen Gross <jgross@suse.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com>
xen: selfballoon: remove unnecessary static in frontswap_selfshrink()
Remove unnecessary static on local variables last_frontswap_pages and
tgt_frontswap_pages. Such variables are initialized before being used,
on every execution path throughout the function. The statics have no
benefit and, removing them reduce the code size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
You can see a significant difference in the code size after executing
the size command, before and after the code change:
before:
text data bss dec hex filename
5633 3452 384 9469 24fd drivers/xen/xen-selfballoon.o
after:
text data bss dec hex filename
5576 3308 256 9140 23b4 drivers/xen/xen-selfballoon.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com>
Merge tag 'sound-4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This is a pretty boring pull request, containing a few HD-audio quirks
and ID updates as usual suspects, as well as a fix for a regression of
FM801 chip on ia64 (what a legacy combination!)"
* tag 'sound-4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add mute led support for HP ProBook 440 G4
ALSA: hda/realtek - No loopback on ALC225/ALC295 codec
ALSA: hda/realtek - Update headset mode for ALC225
ALSA: fm801: Initialize chip after IRQ handler is registered
ALSA: hda/realtek - Update headset mode for ALC298
ALSA: hda - Add missing NVIDIA GPU codec IDs to patch table
Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Two areas addressed by these fixes:
- Fixes from Dave Martin for the signal frames that were broken with
certain configurations. No one noticed until recently.
- More kexec fixes to ensure that the crashkernel region is correctly
allocated, and a fix for the location of the device tree when
several kexec kernels are loaded"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8687/1: signal: Fix unparseable iwmmxt_sigframe in uc_regspace[]
ARM: 8686/1: iwmmxt: Add missing __user annotations to sigframe accessors
ARM: kexec: fix failure to boot crash kernel
ARM: kexec: avoid allocating crashkernel region outside lowmem
NFS: Optimize fallocate by refreshing mapping when needed.
posix_fallocate() will allocate space in an NFS file by considering
the last byte of every 4K block. If it is before EOF, it will read
the byte and if it is zero, a zero is written out. If it is after EOF,
the zero is unconditionally written.
For the blocks beyond EOF, if NFS believes its cache is valid, it will
expand these writes to write full pages, and then will merge the pages.
This results if (typically) 1MB writes. If NFS believes its cache is
not valid (particularly if NFS_INO_INVALID_DATA or
NFS_INO_REVAL_PAGECACHE are set - see nfs_write_pageuptodate()), it will
send the individual 1-byte writes. This results in (typically) 256 times
as many RPC requests, and can be substantially slower.
Currently nfs_revalidate_mapping() is only used when reading a file or
mmapping a file, as these are times when the content needs to be
up-to-date. Writes don't generally need the cache to be up-to-date, but
writes beyond EOF can benefit, particularly in the posix_fallocate()
case.
So this patch calls nfs_revalidate_mapping() when writing beyond EOF -
i.e. when there is a gap between the end of the file and the start of
the write. If the cache is thought to be out of date (as happens after
taking a file lock), this will cause a GETATTR, and the two flags
mentioned above will be cleared. With this, posix_fallocate() on a
newly locked file does not generate excessive tiny writes.
Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Prior to commit ca0daa277aca ("NFS: Cache aggressively when file is open
for writing"), NFS would revalidate, or invalidate, the file size when
taking a lock. Since that commit it only invalidates the file content.
If the file size is changed on the server while wait for the lock, the
client will have an incorrect understanding of the file size and could
corrupt data. This particularly happens when writing beyond the
(supposed) end of file and can be easily be demonstrated with
posix_fallocate().
If an application opens an empty file, waits for a write lock, and then
calls posix_fallocate(), glibc will determine that the underlying
filesystem doesn't support fallocate (assuming version 4.1 or earlier)
and will write out a '0' byte at the end of each 4K page in the region
being fallocated that is after the end of the file.
NFS will (usually) detect that these writes are beyond EOF and will
expand them to cover the whole page, and then will merge the pages.
Consequently, NFS will write out large blocks of zeroes beyond where it
thought EOF was. If EOF had moved, the pre-existing part of the file
will be over-written. Locking should have protected against this,
but it doesn't.
This patch restores the use of nfs_zap_caches() which invalidated the
cached attributes. When posix_fallocate() asks for the file size, the
request will go to the server and get a correct answer.
cc: stable@vger.kernel.org (v4.8+) Fixes: ca0daa277aca ("NFS: Cache aggressively when file is open for writing") Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
gpu: host1x: Free the IOMMU domain when there is no device to attach
When there is no device to attach to the IOMMU domain, as may be the
case when the device-tree does not contain the proper iommu node, it is
best to keep going without IOMMU support rather than failing.
This allows the driver to probe and function instead of taking down
all of the tegra drm driver, leading to missing display support.
Shawn Lin [Tue, 18 Jul 2017 08:31:38 +0000 (16:31 +0800)]
Documentation: dw-mshc: deprecate num-slots
dwmmc host driver already deprecate it in the driver
but didn't modify the documentation to reflect the fact.
This patch deprecates it and clean up num-slots from the
examples of all variant host drivers.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Rob Herring <robh@kernel.org> Fixes: d30a8f7bdf64 ("mmc: dw_mmc: deprecated the "num-slots" property") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
projects / arm / linux.git / log