backport the driver from RHEL5.3 and make it work.
signed-off-by: Zhang Yang <yang.zhang@intel.com>
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
+# CONFIG_E1000E is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
CONFIG_E1000=y
+CONFIG_E1000E=y
# CONFIG_E1000_NAPI is not set
# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
# CONFIG_NS83820 is not set
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
CONFIG_E1000=y
+CONFIG_E1000E=y
# CONFIG_E1000_NAPI is not set
# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
# CONFIG_NS83820 is not set
If in doubt, say N.
+config E1000E
+ tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support"
+ depends on PCI
+ ---help---
+ This driver supports the PCI-Express Intel(R) PRO/1000 gigabit
+ ethernet family of adapters. For PCI or PCI-X e1000 adapters,
+ use the regular e1000 driver For more information on how to
+ identify your adapter, go to the Adapter & Driver ID Guide at:
+
+ <http://support.intel.com/support/network/adapter/pro100/21397.htm>
+
+ For general information and support, go to the Intel support
+ website at:
+
+ <http://support.intel.com>
+
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/e1000e.txt>.
+
+ To compile this driver as a module, choose M here and read
+ <file:Documentation/networking/net-modules.txt>. The module
+ will be called e1000e.
+
source "drivers/net/ixp2000/Kconfig"
config MYRI_SBUS
endif
obj-$(CONFIG_E1000) += e1000/
+obj-$(CONFIG_E1000E) += e1000e/
obj-$(CONFIG_IBM_EMAC) += ibm_emac/
obj-$(CONFIG_IXGB) += ixgb/
obj-$(CONFIG_IXGBE) += ixgbe/
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2008 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+/*
+ * 82571EB Gigabit Ethernet Controller
+ * 82571EB Gigabit Ethernet Controller (Fiber)
+ * 82571EB Dual Port Gigabit Mezzanine Adapter
+ * 82571EB Quad Port Gigabit Mezzanine Adapter
+ * 82571PT Gigabit PT Quad Port Server ExpressModule
+ * 82572EI Gigabit Ethernet Controller (Copper)
+ * 82572EI Gigabit Ethernet Controller (Fiber)
+ * 82572EI Gigabit Ethernet Controller
+ * 82573V Gigabit Ethernet Controller (Copper)
+ * 82573E Gigabit Ethernet Controller (Copper)
+ * 82573L Gigabit Ethernet Controller
+ * 82574L Gigabit Network Connection
+ */
+
+#include <linux/netdevice.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+
+#include "e1000.h"
+
+#define ID_LED_RESERVED_F746 0xF746
+#define ID_LED_DEFAULT_82573 ((ID_LED_DEF1_DEF2 << 12) | \
+ (ID_LED_OFF1_ON2 << 8) | \
+ (ID_LED_DEF1_DEF2 << 4) | \
+ (ID_LED_DEF1_DEF2))
+
+#define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000
+
+#define E1000_NVM_INIT_CTRL2_MNGM 0x6000 /* Manageability Operation Mode mask */
+
+static s32 e1000_get_phy_id_82571(struct e1000_hw *hw);
+static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw);
+static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw);
+static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data);
+static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw);
+static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw);
+static s32 e1000_setup_link_82571(struct e1000_hw *hw);
+static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw);
+static bool e1000_check_mng_mode_82574(struct e1000_hw *hw);
+static s32 e1000_led_on_82574(struct e1000_hw *hw);
+
+/**
+ * e1000_init_phy_params_82571 - Init PHY func ptrs.
+ * @hw: pointer to the HW structure
+ *
+ * This is a function pointer entry point called by the api module.
+ **/
+static s32 e1000_init_phy_params_82571(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+
+ if (hw->phy.media_type != e1000_media_type_copper) {
+ phy->type = e1000_phy_none;
+ return 0;
+ }
+
+ phy->addr = 1;
+ phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+ phy->reset_delay_us = 100;
+
+ switch (hw->mac.type) {
+ case e1000_82571:
+ case e1000_82572:
+ phy->type = e1000_phy_igp_2;
+ break;
+ case e1000_82573:
+ phy->type = e1000_phy_m88;
+ break;
+ case e1000_82574:
+ phy->type = e1000_phy_bm;
+ break;
+ default:
+ return -E1000_ERR_PHY;
+ break;
+ }
+
+ /* This can only be done after all function pointers are setup. */
+ ret_val = e1000_get_phy_id_82571(hw);
+
+ /* Verify phy id */
+ switch (hw->mac.type) {
+ case e1000_82571:
+ case e1000_82572:
+ if (phy->id != IGP01E1000_I_PHY_ID)
+ return -E1000_ERR_PHY;
+ break;
+ case e1000_82573:
+ if (phy->id != M88E1111_I_PHY_ID)
+ return -E1000_ERR_PHY;
+ break;
+ case e1000_82574:
+ if (phy->id != BME1000_E_PHY_ID_R2)
+ return -E1000_ERR_PHY;
+ break;
+ default:
+ return -E1000_ERR_PHY;
+ break;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_init_nvm_params_82571 - Init NVM func ptrs.
+ * @hw: pointer to the HW structure
+ *
+ * This is a function pointer entry point called by the api module.
+ **/
+static s32 e1000_init_nvm_params_82571(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ u32 eecd = er32(EECD);
+ u16 size;
+
+ nvm->opcode_bits = 8;
+ nvm->delay_usec = 1;
+ switch (nvm->override) {
+ case e1000_nvm_override_spi_large:
+ nvm->page_size = 32;
+ nvm->address_bits = 16;
+ break;
+ case e1000_nvm_override_spi_small:
+ nvm->page_size = 8;
+ nvm->address_bits = 8;
+ break;
+ default:
+ nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8;
+ nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8;
+ break;
+ }
+
+ switch (hw->mac.type) {
+ case e1000_82573:
+ case e1000_82574:
+ if (((eecd >> 15) & 0x3) == 0x3) {
+ nvm->type = e1000_nvm_flash_hw;
+ nvm->word_size = 2048;
+ /*
+ * Autonomous Flash update bit must be cleared due
+ * to Flash update issue.
+ */
+ eecd &= ~E1000_EECD_AUPDEN;
+ ew32(EECD, eecd);
+ break;
+ }
+ /* Fall Through */
+ default:
+ nvm->type = e1000_nvm_eeprom_spi;
+ size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
+ E1000_EECD_SIZE_EX_SHIFT);
+ /*
+ * Added to a constant, "size" becomes the left-shift value
+ * for setting word_size.
+ */
+ size += NVM_WORD_SIZE_BASE_SHIFT;
+
+ /* EEPROM access above 16k is unsupported */
+ if (size > 14)
+ size = 14;
+ nvm->word_size = 1 << size;
+ break;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_init_mac_params_82571 - Init MAC func ptrs.
+ * @hw: pointer to the HW structure
+ *
+ * This is a function pointer entry point called by the api module.
+ **/
+static s32 e1000_init_mac_params_82571(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_mac_info *mac = &hw->mac;
+ struct e1000_mac_operations *func = &mac->ops;
+
+ /* Set media type */
+ switch (adapter->pdev->device) {
+ case E1000_DEV_ID_82571EB_FIBER:
+ case E1000_DEV_ID_82572EI_FIBER:
+ case E1000_DEV_ID_82571EB_QUAD_FIBER:
+ hw->phy.media_type = e1000_media_type_fiber;
+ break;
+ case E1000_DEV_ID_82571EB_SERDES:
+ case E1000_DEV_ID_82572EI_SERDES:
+ case E1000_DEV_ID_82571EB_SERDES_DUAL:
+ case E1000_DEV_ID_82571EB_SERDES_QUAD:
+ hw->phy.media_type = e1000_media_type_internal_serdes;
+ break;
+ default:
+ hw->phy.media_type = e1000_media_type_copper;
+ break;
+ }
+
+ /* Set mta register count */
+ mac->mta_reg_count = 128;
+ /* Set rar entry count */
+ mac->rar_entry_count = E1000_RAR_ENTRIES;
+ /* Set if manageability features are enabled. */
+ mac->arc_subsystem_valid = (er32(FWSM) & E1000_FWSM_MODE_MASK) ? 1 : 0;
+
+ /* check for link */
+ switch (hw->phy.media_type) {
+ case e1000_media_type_copper:
+ func->setup_physical_interface = e1000_setup_copper_link_82571;
+ func->check_for_link = e1000e_check_for_copper_link;
+ func->get_link_up_info = e1000e_get_speed_and_duplex_copper;
+ break;
+ case e1000_media_type_fiber:
+ func->setup_physical_interface =
+ e1000_setup_fiber_serdes_link_82571;
+ func->check_for_link = e1000e_check_for_fiber_link;
+ func->get_link_up_info =
+ e1000e_get_speed_and_duplex_fiber_serdes;
+ break;
+ case e1000_media_type_internal_serdes:
+ func->setup_physical_interface =
+ e1000_setup_fiber_serdes_link_82571;
+ func->check_for_link = e1000e_check_for_serdes_link;
+ func->get_link_up_info =
+ e1000e_get_speed_and_duplex_fiber_serdes;
+ break;
+ default:
+ return -E1000_ERR_CONFIG;
+ break;
+ }
+
+ switch (hw->mac.type) {
+ case e1000_82574:
+ func->check_mng_mode = e1000_check_mng_mode_82574;
+ func->led_on = e1000_led_on_82574;
+ break;
+ default:
+ func->check_mng_mode = e1000e_check_mng_mode_generic;
+ func->led_on = e1000e_led_on_generic;
+ break;
+ }
+
+ return 0;
+}
+
+static s32 e1000_get_variants_82571(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ static int global_quad_port_a; /* global port a indication */
+ struct pci_dev *pdev = adapter->pdev;
+ u16 eeprom_data = 0;
+ int is_port_b = er32(STATUS) & E1000_STATUS_FUNC_1;
+ s32 rc;
+
+ rc = e1000_init_mac_params_82571(adapter);
+ if (rc)
+ return rc;
+
+ rc = e1000_init_nvm_params_82571(hw);
+ if (rc)
+ return rc;
+
+ rc = e1000_init_phy_params_82571(hw);
+ if (rc)
+ return rc;
+
+ /* tag quad port adapters first, it's used below */
+ switch (pdev->device) {
+ case E1000_DEV_ID_82571EB_QUAD_COPPER:
+ case E1000_DEV_ID_82571EB_QUAD_FIBER:
+ case E1000_DEV_ID_82571EB_QUAD_COPPER_LP:
+ case E1000_DEV_ID_82571PT_QUAD_COPPER:
+ adapter->flags |= FLAG_IS_QUAD_PORT;
+ /* mark the first port */
+ if (global_quad_port_a == 0)
+ adapter->flags |= FLAG_IS_QUAD_PORT_A;
+ /* Reset for multiple quad port adapters */
+ global_quad_port_a++;
+ if (global_quad_port_a == 4)
+ global_quad_port_a = 0;
+ break;
+ default:
+ break;
+ }
+
+ switch (adapter->hw.mac.type) {
+ case e1000_82571:
+ /* these dual ports don't have WoL on port B at all */
+ if (((pdev->device == E1000_DEV_ID_82571EB_FIBER) ||
+ (pdev->device == E1000_DEV_ID_82571EB_SERDES) ||
+ (pdev->device == E1000_DEV_ID_82571EB_COPPER)) &&
+ (is_port_b))
+ adapter->flags &= ~FLAG_HAS_WOL;
+ /* quad ports only support WoL on port A */
+ if (adapter->flags & FLAG_IS_QUAD_PORT &&
+ (!(adapter->flags & FLAG_IS_QUAD_PORT_A)))
+ adapter->flags &= ~FLAG_HAS_WOL;
+ /* Does not support WoL on any port */
+ if (pdev->device == E1000_DEV_ID_82571EB_SERDES_QUAD)
+ adapter->flags &= ~FLAG_HAS_WOL;
+ break;
+
+ case e1000_82573:
+ if (pdev->device == E1000_DEV_ID_82573L) {
+ e1000_read_nvm(&adapter->hw, NVM_INIT_3GIO_3, 1,
+ &eeprom_data);
+ if (eeprom_data & NVM_WORD1A_ASPM_MASK)
+ adapter->flags &= ~FLAG_HAS_JUMBO_FRAMES;
+ }
+ break;
+ default:
+ break;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_get_phy_id_82571 - Retrieve the PHY ID and revision
+ * @hw: pointer to the HW structure
+ *
+ * Reads the PHY registers and stores the PHY ID and possibly the PHY
+ * revision in the hardware structure.
+ **/
+static s32 e1000_get_phy_id_82571(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_id = 0;
+
+ switch (hw->mac.type) {
+ case e1000_82571:
+ case e1000_82572:
+ /*
+ * The 82571 firmware may still be configuring the PHY.
+ * In this case, we cannot access the PHY until the
+ * configuration is done. So we explicitly set the
+ * PHY ID.
+ */
+ phy->id = IGP01E1000_I_PHY_ID;
+ break;
+ case e1000_82573:
+ return e1000e_get_phy_id(hw);
+ break;
+ case e1000_82574:
+ ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
+ if (ret_val)
+ return ret_val;
+
+ phy->id = (u32)(phy_id << 16);
+ udelay(20);
+ ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
+ if (ret_val)
+ return ret_val;
+
+ phy->id |= (u32)(phy_id);
+ phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
+ break;
+ default:
+ return -E1000_ERR_PHY;
+ break;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_get_hw_semaphore_82571 - Acquire hardware semaphore
+ * @hw: pointer to the HW structure
+ *
+ * Acquire the HW semaphore to access the PHY or NVM
+ **/
+static s32 e1000_get_hw_semaphore_82571(struct e1000_hw *hw)
+{
+ u32 swsm;
+ s32 timeout = hw->nvm.word_size + 1;
+ s32 i = 0;
+
+ /* Get the FW semaphore. */
+ for (i = 0; i < timeout; i++) {
+ swsm = er32(SWSM);
+ ew32(SWSM, swsm | E1000_SWSM_SWESMBI);
+
+ /* Semaphore acquired if bit latched */
+ if (er32(SWSM) & E1000_SWSM_SWESMBI)
+ break;
+
+ udelay(50);
+ }
+
+ if (i == timeout) {
+ /* Release semaphores */
+ e1000e_put_hw_semaphore(hw);
+ hw_dbg(hw, "Driver can't access the NVM\n");
+ return -E1000_ERR_NVM;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_put_hw_semaphore_82571 - Release hardware semaphore
+ * @hw: pointer to the HW structure
+ *
+ * Release hardware semaphore used to access the PHY or NVM
+ **/
+static void e1000_put_hw_semaphore_82571(struct e1000_hw *hw)
+{
+ u32 swsm;
+
+ swsm = er32(SWSM);
+
+ swsm &= ~E1000_SWSM_SWESMBI;
+
+ ew32(SWSM, swsm);
+}
+
+/**
+ * e1000_acquire_nvm_82571 - Request for access to the EEPROM
+ * @hw: pointer to the HW structure
+ *
+ * To gain access to the EEPROM, first we must obtain a hardware semaphore.
+ * Then for non-82573 hardware, set the EEPROM access request bit and wait
+ * for EEPROM access grant bit. If the access grant bit is not set, release
+ * hardware semaphore.
+ **/
+static s32 e1000_acquire_nvm_82571(struct e1000_hw *hw)
+{
+ s32 ret_val;
+
+ ret_val = e1000_get_hw_semaphore_82571(hw);
+ if (ret_val)
+ return ret_val;
+
+ if (hw->mac.type != e1000_82573 && hw->mac.type != e1000_82574)
+ ret_val = e1000e_acquire_nvm(hw);
+
+ if (ret_val)
+ e1000_put_hw_semaphore_82571(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_release_nvm_82571 - Release exclusive access to EEPROM
+ * @hw: pointer to the HW structure
+ *
+ * Stop any current commands to the EEPROM and clear the EEPROM request bit.
+ **/
+static void e1000_release_nvm_82571(struct e1000_hw *hw)
+{
+ e1000e_release_nvm(hw);
+ e1000_put_hw_semaphore_82571(hw);
+}
+
+/**
+ * e1000_write_nvm_82571 - Write to EEPROM using appropriate interface
+ * @hw: pointer to the HW structure
+ * @offset: offset within the EEPROM to be written to
+ * @words: number of words to write
+ * @data: 16 bit word(s) to be written to the EEPROM
+ *
+ * For non-82573 silicon, write data to EEPROM at offset using SPI interface.
+ *
+ * If e1000e_update_nvm_checksum is not called after this function, the
+ * EEPROM will most likely contain an invalid checksum.
+ **/
+static s32 e1000_write_nvm_82571(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data)
+{
+ s32 ret_val;
+
+ switch (hw->mac.type) {
+ case e1000_82573:
+ case e1000_82574:
+ ret_val = e1000_write_nvm_eewr_82571(hw, offset, words, data);
+ break;
+ case e1000_82571:
+ case e1000_82572:
+ ret_val = e1000e_write_nvm_spi(hw, offset, words, data);
+ break;
+ default:
+ ret_val = -E1000_ERR_NVM;
+ break;
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000_update_nvm_checksum_82571 - Update EEPROM checksum
+ * @hw: pointer to the HW structure
+ *
+ * Updates the EEPROM checksum by reading/adding each word of the EEPROM
+ * up to the checksum. Then calculates the EEPROM checksum and writes the
+ * value to the EEPROM.
+ **/
+static s32 e1000_update_nvm_checksum_82571(struct e1000_hw *hw)
+{
+ u32 eecd;
+ s32 ret_val;
+ u16 i;
+
+ ret_val = e1000e_update_nvm_checksum_generic(hw);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * If our nvm is an EEPROM, then we're done
+ * otherwise, commit the checksum to the flash NVM.
+ */
+ if (hw->nvm.type != e1000_nvm_flash_hw)
+ return ret_val;
+
+ /* Check for pending operations. */
+ for (i = 0; i < E1000_FLASH_UPDATES; i++) {
+ msleep(1);
+ if ((er32(EECD) & E1000_EECD_FLUPD) == 0)
+ break;
+ }
+
+ if (i == E1000_FLASH_UPDATES)
+ return -E1000_ERR_NVM;
+
+ /* Reset the firmware if using STM opcode. */
+ if ((er32(FLOP) & 0xFF00) == E1000_STM_OPCODE) {
+ /*
+ * The enabling of and the actual reset must be done
+ * in two write cycles.
+ */
+ ew32(HICR, E1000_HICR_FW_RESET_ENABLE);
+ e1e_flush();
+ ew32(HICR, E1000_HICR_FW_RESET);
+ }
+
+ /* Commit the write to flash */
+ eecd = er32(EECD) | E1000_EECD_FLUPD;
+ ew32(EECD, eecd);
+
+ for (i = 0; i < E1000_FLASH_UPDATES; i++) {
+ msleep(1);
+ if ((er32(EECD) & E1000_EECD_FLUPD) == 0)
+ break;
+ }
+
+ if (i == E1000_FLASH_UPDATES)
+ return -E1000_ERR_NVM;
+
+ return 0;
+}
+
+/**
+ * e1000_validate_nvm_checksum_82571 - Validate EEPROM checksum
+ * @hw: pointer to the HW structure
+ *
+ * Calculates the EEPROM checksum by reading/adding each word of the EEPROM
+ * and then verifies that the sum of the EEPROM is equal to 0xBABA.
+ **/
+static s32 e1000_validate_nvm_checksum_82571(struct e1000_hw *hw)
+{
+ if (hw->nvm.type == e1000_nvm_flash_hw)
+ e1000_fix_nvm_checksum_82571(hw);
+
+ return e1000e_validate_nvm_checksum_generic(hw);
+}
+
+/**
+ * e1000_write_nvm_eewr_82571 - Write to EEPROM for 82573 silicon
+ * @hw: pointer to the HW structure
+ * @offset: offset within the EEPROM to be written to
+ * @words: number of words to write
+ * @data: 16 bit word(s) to be written to the EEPROM
+ *
+ * After checking for invalid values, poll the EEPROM to ensure the previous
+ * command has completed before trying to write the next word. After write
+ * poll for completion.
+ *
+ * If e1000e_update_nvm_checksum is not called after this function, the
+ * EEPROM will most likely contain an invalid checksum.
+ **/
+static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ u32 i;
+ u32 eewr = 0;
+ s32 ret_val = 0;
+
+ /*
+ * A check for invalid values: offset too large, too many words,
+ * and not enough words.
+ */
+ if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) ||
+ (words == 0)) {
+ hw_dbg(hw, "nvm parameter(s) out of bounds\n");
+ return -E1000_ERR_NVM;
+ }
+
+ for (i = 0; i < words; i++) {
+ eewr = (data[i] << E1000_NVM_RW_REG_DATA) |
+ ((offset+i) << E1000_NVM_RW_ADDR_SHIFT) |
+ E1000_NVM_RW_REG_START;
+
+ ret_val = e1000e_poll_eerd_eewr_done(hw, E1000_NVM_POLL_WRITE);
+ if (ret_val)
+ break;
+
+ ew32(EEWR, eewr);
+
+ ret_val = e1000e_poll_eerd_eewr_done(hw, E1000_NVM_POLL_WRITE);
+ if (ret_val)
+ break;
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000_get_cfg_done_82571 - Poll for configuration done
+ * @hw: pointer to the HW structure
+ *
+ * Reads the management control register for the config done bit to be set.
+ **/
+static s32 e1000_get_cfg_done_82571(struct e1000_hw *hw)
+{
+ s32 timeout = PHY_CFG_TIMEOUT;
+
+ while (timeout) {
+ if (er32(EEMNGCTL) &
+ E1000_NVM_CFG_DONE_PORT_0)
+ break;
+ msleep(1);
+ timeout--;
+ }
+ if (!timeout) {
+ hw_dbg(hw, "MNG configuration cycle has not completed.\n");
+ return -E1000_ERR_RESET;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_set_d0_lplu_state_82571 - Set Low Power Linkup D0 state
+ * @hw: pointer to the HW structure
+ * @active: TRUE to enable LPLU, FALSE to disable
+ *
+ * Sets the LPLU D0 state according to the active flag. When activating LPLU
+ * this function also disables smart speed and vice versa. LPLU will not be
+ * activated unless the device autonegotiation advertisement meets standards
+ * of either 10 or 10/100 or 10/100/1000 at all duplexes. This is a function
+ * pointer entry point only called by PHY setup routines.
+ **/
+static s32 e1000_set_d0_lplu_state_82571(struct e1000_hw *hw, bool active)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+
+ ret_val = e1e_rphy(hw, IGP02E1000_PHY_POWER_MGMT, &data);
+ if (ret_val)
+ return ret_val;
+
+ if (active) {
+ data |= IGP02E1000_PM_D0_LPLU;
+ ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, data);
+ if (ret_val)
+ return ret_val;
+
+ /* When LPLU is enabled, we should disable SmartSpeed */
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data);
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data);
+ if (ret_val)
+ return ret_val;
+ } else {
+ data &= ~IGP02E1000_PM_D0_LPLU;
+ ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, data);
+ /*
+ * LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ * during Dx states where the power conservation is most
+ * important. During driver activity we should enable
+ * SmartSpeed, so performance is maintained.
+ */
+ if (phy->smart_speed == e1000_smart_speed_on) {
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ return ret_val;
+
+ data |= IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ return ret_val;
+ } else if (phy->smart_speed == e1000_smart_speed_off) {
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ return ret_val;
+
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ return ret_val;
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_reset_hw_82571 - Reset hardware
+ * @hw: pointer to the HW structure
+ *
+ * This resets the hardware into a known state. This is a
+ * function pointer entry point called by the api module.
+ **/
+static s32 e1000_reset_hw_82571(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ u32 extcnf_ctrl;
+ u32 ctrl_ext;
+ u32 icr;
+ s32 ret_val;
+ u16 i = 0;
+
+ /*
+ * Prevent the PCI-E bus from sticking if there is no TLP connection
+ * on the last TLP read/write transaction when MAC is reset.
+ */
+ ret_val = e1000e_disable_pcie_master(hw);
+ if (ret_val)
+ hw_dbg(hw, "PCI-E Master disable polling has failed.\n");
+
+ hw_dbg(hw, "Masking off all interrupts\n");
+ ew32(IMC, 0xffffffff);
+
+ ew32(RCTL, 0);
+ ew32(TCTL, E1000_TCTL_PSP);
+ e1e_flush();
+
+ msleep(10);
+
+ /*
+ * Must acquire the MDIO ownership before MAC reset.
+ * Ownership defaults to firmware after a reset.
+ */
+ if (hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) {
+ extcnf_ctrl = er32(EXTCNF_CTRL);
+ extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
+
+ do {
+ ew32(EXTCNF_CTRL, extcnf_ctrl);
+ extcnf_ctrl = er32(EXTCNF_CTRL);
+
+ if (extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP)
+ break;
+
+ extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
+
+ msleep(2);
+ i++;
+ } while (i < MDIO_OWNERSHIP_TIMEOUT);
+ }
+
+ ctrl = er32(CTRL);
+
+ hw_dbg(hw, "Issuing a global reset to MAC\n");
+ ew32(CTRL, ctrl | E1000_CTRL_RST);
+
+ if (hw->nvm.type == e1000_nvm_flash_hw) {
+ udelay(10);
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_EE_RST;
+ ew32(CTRL_EXT, ctrl_ext);
+ e1e_flush();
+ }
+
+ ret_val = e1000e_get_auto_rd_done(hw);
+ if (ret_val)
+ /* We don't want to continue accessing MAC registers. */
+ return ret_val;
+
+ /*
+ * Phy configuration from NVM just starts after EECD_AUTO_RD is set.
+ * Need to wait for Phy configuration completion before accessing
+ * NVM and Phy.
+ */
+ if (hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574)
+ msleep(25);
+
+ /* Clear any pending interrupt events. */
+ ew32(IMC, 0xffffffff);
+ icr = er32(ICR);
+
+ if (hw->mac.type == e1000_82571 &&
+ hw->dev_spec.e82571.alt_mac_addr_is_present)
+ e1000e_set_laa_state_82571(hw, 1);
+
+ return 0;
+}
+
+/**
+ * e1000_init_hw_82571 - Initialize hardware
+ * @hw: pointer to the HW structure
+ *
+ * This inits the hardware readying it for operation.
+ **/
+static s32 e1000_init_hw_82571(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 reg_data;
+ s32 ret_val;
+ u16 i;
+ u16 rar_count = mac->rar_entry_count;
+
+ e1000_initialize_hw_bits_82571(hw);
+
+ /* Initialize identification LED */
+ ret_val = e1000e_id_led_init(hw);
+ if (ret_val) {
+ hw_dbg(hw, "Error initializing identification LED\n");
+ return ret_val;
+ }
+
+ /* Disabling VLAN filtering */
+ hw_dbg(hw, "Initializing the IEEE VLAN\n");
+ e1000e_clear_vfta(hw);
+
+ /* Setup the receive address. */
+ /*
+ * If, however, a locally administered address was assigned to the
+ * 82571, we must reserve a RAR for it to work around an issue where
+ * resetting one port will reload the MAC on the other port.
+ */
+ if (e1000e_get_laa_state_82571(hw))
+ rar_count--;
+ e1000e_init_rx_addrs(hw, rar_count);
+
+ /* Zero out the Multicast HASH table */
+ hw_dbg(hw, "Zeroing the MTA\n");
+ for (i = 0; i < mac->mta_reg_count; i++)
+ E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);
+
+ /* Setup link and flow control */
+ ret_val = e1000_setup_link_82571(hw);
+
+ /* Set the transmit descriptor write-back policy */
+ reg_data = er32(TXDCTL(0));
+ reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB |
+ E1000_TXDCTL_COUNT_DESC;
+ ew32(TXDCTL(0), reg_data);
+
+ /* ...for both queues. */
+ if (mac->type != e1000_82573 && mac->type != e1000_82574) {
+ reg_data = er32(TXDCTL(1));
+ reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB |
+ E1000_TXDCTL_COUNT_DESC;
+ ew32(TXDCTL(1), reg_data);
+ } else {
+ e1000e_enable_tx_pkt_filtering(hw);
+ reg_data = er32(GCR);
+ reg_data |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX;
+ ew32(GCR, reg_data);
+ }
+
+ /*
+ * Clear all of the statistics registers (clear on read). It is
+ * important that we do this after we have tried to establish link
+ * because the symbol error count will increment wildly if there
+ * is no link.
+ */
+ e1000_clear_hw_cntrs_82571(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_initialize_hw_bits_82571 - Initialize hardware-dependent bits
+ * @hw: pointer to the HW structure
+ *
+ * Initializes required hardware-dependent bits needed for normal operation.
+ **/
+static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw)
+{
+ u32 reg;
+
+ /* Transmit Descriptor Control 0 */
+ reg = er32(TXDCTL(0));
+ reg |= (1 << 22);
+ ew32(TXDCTL(0), reg);
+
+ /* Transmit Descriptor Control 1 */
+ reg = er32(TXDCTL(1));
+ reg |= (1 << 22);
+ ew32(TXDCTL(1), reg);
+
+ /* Transmit Arbitration Control 0 */
+ reg = er32(TARC(0));
+ reg &= ~(0xF << 27); /* 30:27 */
+ switch (hw->mac.type) {
+ case e1000_82571:
+ case e1000_82572:
+ reg |= (1 << 23) | (1 << 24) | (1 << 25) | (1 << 26);
+ break;
+ default:
+ break;
+ }
+ ew32(TARC(0), reg);
+
+ /* Transmit Arbitration Control 1 */
+ reg = er32(TARC(1));
+ switch (hw->mac.type) {
+ case e1000_82571:
+ case e1000_82572:
+ reg &= ~((1 << 29) | (1 << 30));
+ reg |= (1 << 22) | (1 << 24) | (1 << 25) | (1 << 26);
+ if (er32(TCTL) & E1000_TCTL_MULR)
+ reg &= ~(1 << 28);
+ else
+ reg |= (1 << 28);
+ ew32(TARC(1), reg);
+ break;
+ default:
+ break;
+ }
+
+ /* Device Control */
+ if (hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) {
+ reg = er32(CTRL);
+ reg &= ~(1 << 29);
+ ew32(CTRL, reg);
+ }
+
+ /* Extended Device Control */
+ if (hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) {
+ reg = er32(CTRL_EXT);
+ reg &= ~(1 << 23);
+ reg |= (1 << 22);
+ ew32(CTRL_EXT, reg);
+ }
+
+ if (hw->mac.type == e1000_82571) {
+ reg = er32(PBA_ECC);
+ reg |= E1000_PBA_ECC_CORR_EN;
+ ew32(PBA_ECC, reg);
+ }
+
+ /* PCI-Ex Control Register */
+ if (hw->mac.type == e1000_82574) {
+ reg = er32(GCR);
+ reg |= (1 << 22);
+ ew32(GCR, reg);
+ }
+
+ return;
+}
+
+/**
+ * e1000e_clear_vfta - Clear VLAN filter table
+ * @hw: pointer to the HW structure
+ *
+ * Clears the register array which contains the VLAN filter table by
+ * setting all the values to 0.
+ **/
+void e1000e_clear_vfta(struct e1000_hw *hw)
+{
+ u32 offset;
+ u32 vfta_value = 0;
+ u32 vfta_offset = 0;
+ u32 vfta_bit_in_reg = 0;
+
+ if (hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) {
+ if (hw->mng_cookie.vlan_id != 0) {
+ /*
+ * The VFTA is a 4096b bit-field, each identifying
+ * a single VLAN ID. The following operations
+ * determine which 32b entry (i.e. offset) into the
+ * array we want to set the VLAN ID (i.e. bit) of
+ * the manageability unit.
+ */
+ vfta_offset = (hw->mng_cookie.vlan_id >>
+ E1000_VFTA_ENTRY_SHIFT) &
+ E1000_VFTA_ENTRY_MASK;
+ vfta_bit_in_reg = 1 << (hw->mng_cookie.vlan_id &
+ E1000_VFTA_ENTRY_BIT_SHIFT_MASK);
+ }
+ }
+ for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) {
+ /*
+ * If the offset we want to clear is the same offset of the
+ * manageability VLAN ID, then clear all bits except that of
+ * the manageability unit.
+ */
+ vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0;
+ E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, vfta_value);
+ e1e_flush();
+ }
+}
+
+/**
+ * e1000_check_mng_mode_82574 - Check manageability is enabled
+ * @hw: pointer to the HW structure
+ *
+ * Reads the NVM Initialization Control Word 2 and returns true
+ * (>0) if any manageability is enabled, else false (0).
+ **/
+static bool e1000_check_mng_mode_82574(struct e1000_hw *hw)
+{
+ u16 data;
+
+ e1000_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &data);
+ return (data & E1000_NVM_INIT_CTRL2_MNGM) != 0;
+}
+
+/**
+ * e1000_led_on_82574 - Turn LED on
+ * @hw: pointer to the HW structure
+ *
+ * Turn LED on.
+ **/
+static s32 e1000_led_on_82574(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ u32 i;
+
+ ctrl = hw->mac.ledctl_mode2;
+ if (!(E1000_STATUS_LU & er32(STATUS))) {
+ /*
+ * If no link, then turn LED on by setting the invert bit
+ * for each LED that's "on" (0x0E) in ledctl_mode2.
+ */
+ for (i = 0; i < 4; i++)
+ if (((hw->mac.ledctl_mode2 >> (i * 8)) & 0xFF) ==
+ E1000_LEDCTL_MODE_LED_ON)
+ ctrl |= (E1000_LEDCTL_LED0_IVRT << (i * 8));
+ }
+ ew32(LEDCTL, ctrl);
+
+ return 0;
+}
+
+/**
+ * e1000_update_mc_addr_list_82571 - Update Multicast addresses
+ * @hw: pointer to the HW structure
+ * @mc_addr_list: array of multicast addresses to program
+ * @mc_addr_count: number of multicast addresses to program
+ * @rar_used_count: the first RAR register free to program
+ * @rar_count: total number of supported Receive Address Registers
+ *
+ * Updates the Receive Address Registers and Multicast Table Array.
+ * The caller must have a packed mc_addr_list of multicast addresses.
+ * The parameter rar_count will usually be hw->mac.rar_entry_count
+ * unless there are workarounds that change this.
+ **/
+static void e1000_update_mc_addr_list_82571(struct e1000_hw *hw,
+ u8 *mc_addr_list,
+ u32 mc_addr_count,
+ u32 rar_used_count,
+ u32 rar_count)
+{
+ if (e1000e_get_laa_state_82571(hw))
+ rar_count--;
+
+ e1000e_update_mc_addr_list_generic(hw, mc_addr_list, mc_addr_count,
+ rar_used_count, rar_count);
+}
+
+/**
+ * e1000_setup_link_82571 - Setup flow control and link settings
+ * @hw: pointer to the HW structure
+ *
+ * Determines which flow control settings to use, then configures flow
+ * control. Calls the appropriate media-specific link configuration
+ * function. Assuming the adapter has a valid link partner, a valid link
+ * should be established. Assumes the hardware has previously been reset
+ * and the transmitter and receiver are not enabled.
+ **/
+static s32 e1000_setup_link_82571(struct e1000_hw *hw)
+{
+ /*
+ * 82573 does not have a word in the NVM to determine
+ * the default flow control setting, so we explicitly
+ * set it to full.
+ */
+ if ((hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) &&
+ hw->fc.type == e1000_fc_default)
+ hw->fc.type = e1000_fc_full;
+
+ return e1000e_setup_link(hw);
+}
+
+/**
+ * e1000_setup_copper_link_82571 - Configure copper link settings
+ * @hw: pointer to the HW structure
+ *
+ * Configures the link for auto-neg or forced speed and duplex. Then we check
+ * for link, once link is established calls to configure collision distance
+ * and flow control are called.
+ **/
+static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ u32 led_ctrl;
+ s32 ret_val;
+
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_SLU;
+ ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ew32(CTRL, ctrl);
+
+ switch (hw->phy.type) {
+ case e1000_phy_m88:
+ case e1000_phy_bm:
+ ret_val = e1000e_copper_link_setup_m88(hw);
+ break;
+ case e1000_phy_igp_2:
+ ret_val = e1000e_copper_link_setup_igp(hw);
+ /* Setup activity LED */
+ led_ctrl = er32(LEDCTL);
+ led_ctrl &= IGP_ACTIVITY_LED_MASK;
+ led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
+ ew32(LEDCTL, led_ctrl);
+ break;
+ default:
+ return -E1000_ERR_PHY;
+ break;
+ }
+
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000e_setup_copper_link(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_setup_fiber_serdes_link_82571 - Setup link for fiber/serdes
+ * @hw: pointer to the HW structure
+ *
+ * Configures collision distance and flow control for fiber and serdes links.
+ * Upon successful setup, poll for link.
+ **/
+static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw)
+{
+ switch (hw->mac.type) {
+ case e1000_82571:
+ case e1000_82572:
+ /*
+ * If SerDes loopback mode is entered, there is no form
+ * of reset to take the adapter out of that mode. So we
+ * have to explicitly take the adapter out of loopback
+ * mode. This prevents drivers from twiddling their thumbs
+ * if another tool failed to take it out of loopback mode.
+ */
+ ew32(SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK);
+ break;
+ default:
+ break;
+ }
+
+ return e1000e_setup_fiber_serdes_link(hw);
+}
+
+/**
+ * e1000_valid_led_default_82571 - Verify a valid default LED config
+ * @hw: pointer to the HW structure
+ * @data: pointer to the NVM (EEPROM)
+ *
+ * Read the EEPROM for the current default LED configuration. If the
+ * LED configuration is not valid, set to a valid LED configuration.
+ **/
+static s32 e1000_valid_led_default_82571(struct e1000_hw *hw, u16 *data)
+{
+ s32 ret_val;
+
+ ret_val = e1000_read_nvm(hw, NVM_ID_LED_SETTINGS, 1, data);
+ if (ret_val) {
+ hw_dbg(hw, "NVM Read Error\n");
+ return ret_val;
+ }
+
+ if ((hw->mac.type == e1000_82573 || hw->mac.type == e1000_82574) &&
+ *data == ID_LED_RESERVED_F746)
+ *data = ID_LED_DEFAULT_82573;
+ else if (*data == ID_LED_RESERVED_0000 || *data == ID_LED_RESERVED_FFFF)
+ *data = ID_LED_DEFAULT;
+
+ return 0;
+}
+
+/**
+ * e1000e_get_laa_state_82571 - Get locally administered address state
+ * @hw: pointer to the HW structure
+ *
+ * Retrieve and return the current locally administered address state.
+ **/
+bool e1000e_get_laa_state_82571(struct e1000_hw *hw)
+{
+ if (hw->mac.type != e1000_82571)
+ return 0;
+
+ return hw->dev_spec.e82571.laa_is_present;
+}
+
+/**
+ * e1000e_set_laa_state_82571 - Set locally administered address state
+ * @hw: pointer to the HW structure
+ * @state: enable/disable locally administered address
+ *
+ * Enable/Disable the current locally administers address state.
+ **/
+void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state)
+{
+ if (hw->mac.type != e1000_82571)
+ return;
+
+ hw->dev_spec.e82571.laa_is_present = state;
+
+ /* If workaround is activated... */
+ if (state)
+ /*
+ * Hold a copy of the LAA in RAR[14] This is done so that
+ * between the time RAR[0] gets clobbered and the time it
+ * gets fixed, the actual LAA is in one of the RARs and no
+ * incoming packets directed to this port are dropped.
+ * Eventually the LAA will be in RAR[0] and RAR[14].
+ */
+ e1000e_rar_set(hw, hw->mac.addr, hw->mac.rar_entry_count - 1);
+}
+
+/**
+ * e1000_fix_nvm_checksum_82571 - Fix EEPROM checksum
+ * @hw: pointer to the HW structure
+ *
+ * Verifies that the EEPROM has completed the update. After updating the
+ * EEPROM, we need to check bit 15 in work 0x23 for the checksum fix. If
+ * the checksum fix is not implemented, we need to set the bit and update
+ * the checksum. Otherwise, if bit 15 is set and the checksum is incorrect,
+ * we need to return bad checksum.
+ **/
+static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ s32 ret_val;
+ u16 data;
+
+ if (nvm->type != e1000_nvm_flash_hw)
+ return 0;
+
+ /*
+ * Check bit 4 of word 10h. If it is 0, firmware is done updating
+ * 10h-12h. Checksum may need to be fixed.
+ */
+ ret_val = e1000_read_nvm(hw, 0x10, 1, &data);
+ if (ret_val)
+ return ret_val;
+
+ if (!(data & 0x10)) {
+ /*
+ * Read 0x23 and check bit 15. This bit is a 1
+ * when the checksum has already been fixed. If
+ * the checksum is still wrong and this bit is a
+ * 1, we need to return bad checksum. Otherwise,
+ * we need to set this bit to a 1 and update the
+ * checksum.
+ */
+ ret_val = e1000_read_nvm(hw, 0x23, 1, &data);
+ if (ret_val)
+ return ret_val;
+
+ if (!(data & 0x8000)) {
+ data |= 0x8000;
+ ret_val = e1000_write_nvm(hw, 0x23, 1, &data);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000e_update_nvm_checksum(hw);
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_clear_hw_cntrs_82571 - Clear device specific hardware counters
+ * @hw: pointer to the HW structure
+ *
+ * Clears the hardware counters by reading the counter registers.
+ **/
+static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw)
+{
+ u32 temp;
+
+ e1000e_clear_hw_cntrs_base(hw);
+
+ temp = er32(PRC64);
+ temp = er32(PRC127);
+ temp = er32(PRC255);
+ temp = er32(PRC511);
+ temp = er32(PRC1023);
+ temp = er32(PRC1522);
+ temp = er32(PTC64);
+ temp = er32(PTC127);
+ temp = er32(PTC255);
+ temp = er32(PTC511);
+ temp = er32(PTC1023);
+ temp = er32(PTC1522);
+
+ temp = er32(ALGNERRC);
+ temp = er32(RXERRC);
+ temp = er32(TNCRS);
+ temp = er32(CEXTERR);
+ temp = er32(TSCTC);
+ temp = er32(TSCTFC);
+
+ temp = er32(MGTPRC);
+ temp = er32(MGTPDC);
+ temp = er32(MGTPTC);
+
+ temp = er32(IAC);
+ temp = er32(ICRXOC);
+
+ temp = er32(ICRXPTC);
+ temp = er32(ICRXATC);
+ temp = er32(ICTXPTC);
+ temp = er32(ICTXATC);
+ temp = er32(ICTXQEC);
+ temp = er32(ICTXQMTC);
+ temp = er32(ICRXDMTC);
+}
+
+static struct e1000_mac_operations e82571_mac_ops = {
+ /* .check_mng_mode: mac type dependent */
+ /* .check_for_link: media type dependent */
+ .cleanup_led = e1000e_cleanup_led_generic,
+ .clear_hw_cntrs = e1000_clear_hw_cntrs_82571,
+ .get_bus_info = e1000e_get_bus_info_pcie,
+ /* .get_link_up_info: media type dependent */
+ /* .led_on: mac type dependent */
+ .led_off = e1000e_led_off_generic,
+ .update_mc_addr_list = e1000_update_mc_addr_list_82571,
+ .reset_hw = e1000_reset_hw_82571,
+ .init_hw = e1000_init_hw_82571,
+ .setup_link = e1000_setup_link_82571,
+ /* .setup_physical_interface: media type dependent */
+};
+
+static struct e1000_phy_operations e82_phy_ops_igp = {
+ .acquire_phy = e1000_get_hw_semaphore_82571,
+ .check_reset_block = e1000e_check_reset_block_generic,
+ .commit_phy = NULL,
+ .force_speed_duplex = e1000e_phy_force_speed_duplex_igp,
+ .get_cfg_done = e1000_get_cfg_done_82571,
+ .get_cable_length = e1000e_get_cable_length_igp_2,
+ .get_phy_info = e1000e_get_phy_info_igp,
+ .read_phy_reg = e1000e_read_phy_reg_igp,
+ .release_phy = e1000_put_hw_semaphore_82571,
+ .reset_phy = e1000e_phy_hw_reset_generic,
+ .set_d0_lplu_state = e1000_set_d0_lplu_state_82571,
+ .set_d3_lplu_state = e1000e_set_d3_lplu_state,
+ .write_phy_reg = e1000e_write_phy_reg_igp,
+};
+
+static struct e1000_phy_operations e82_phy_ops_m88 = {
+ .acquire_phy = e1000_get_hw_semaphore_82571,
+ .check_reset_block = e1000e_check_reset_block_generic,
+ .commit_phy = e1000e_phy_sw_reset,
+ .force_speed_duplex = e1000e_phy_force_speed_duplex_m88,
+ .get_cfg_done = e1000e_get_cfg_done,
+ .get_cable_length = e1000e_get_cable_length_m88,
+ .get_phy_info = e1000e_get_phy_info_m88,
+ .read_phy_reg = e1000e_read_phy_reg_m88,
+ .release_phy = e1000_put_hw_semaphore_82571,
+ .reset_phy = e1000e_phy_hw_reset_generic,
+ .set_d0_lplu_state = e1000_set_d0_lplu_state_82571,
+ .set_d3_lplu_state = e1000e_set_d3_lplu_state,
+ .write_phy_reg = e1000e_write_phy_reg_m88,
+};
+
+static struct e1000_phy_operations e82_phy_ops_bm = {
+ .acquire_phy = e1000_get_hw_semaphore_82571,
+ .check_reset_block = e1000e_check_reset_block_generic,
+ .commit_phy = e1000e_phy_sw_reset,
+ .force_speed_duplex = e1000e_phy_force_speed_duplex_m88,
+ .get_cfg_done = e1000e_get_cfg_done,
+ .get_cable_length = e1000e_get_cable_length_m88,
+ .get_phy_info = e1000e_get_phy_info_m88,
+ .read_phy_reg = e1000e_read_phy_reg_bm2,
+ .release_phy = e1000_put_hw_semaphore_82571,
+ .reset_phy = e1000e_phy_hw_reset_generic,
+ .set_d0_lplu_state = e1000_set_d0_lplu_state_82571,
+ .set_d3_lplu_state = e1000e_set_d3_lplu_state,
+ .write_phy_reg = e1000e_write_phy_reg_bm2,
+};
+
+static struct e1000_nvm_operations e82571_nvm_ops = {
+ .acquire_nvm = e1000_acquire_nvm_82571,
+ .read_nvm = e1000e_read_nvm_eerd,
+ .release_nvm = e1000_release_nvm_82571,
+ .update_nvm = e1000_update_nvm_checksum_82571,
+ .valid_led_default = e1000_valid_led_default_82571,
+ .validate_nvm = e1000_validate_nvm_checksum_82571,
+ .write_nvm = e1000_write_nvm_82571,
+};
+
+struct e1000_info e1000_82571_info = {
+ .mac = e1000_82571,
+ .flags = FLAG_HAS_HW_VLAN_FILTER
+ | FLAG_HAS_JUMBO_FRAMES
+ | FLAG_HAS_WOL
+ | FLAG_APME_IN_CTRL3
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_CTRLEXT_ON_LOAD
+ | FLAG_HAS_SMART_POWER_DOWN
+ | FLAG_RESET_OVERWRITES_LAA /* errata */
+ | FLAG_TARC_SPEED_MODE_BIT /* errata */
+ | FLAG_APME_CHECK_PORT_B,
+ .pba = 38,
+ .get_variants = e1000_get_variants_82571,
+ .mac_ops = &e82571_mac_ops,
+ .phy_ops = &e82_phy_ops_igp,
+ .nvm_ops = &e82571_nvm_ops,
+};
+
+struct e1000_info e1000_82572_info = {
+ .mac = e1000_82572,
+ .flags = FLAG_HAS_HW_VLAN_FILTER
+ | FLAG_HAS_JUMBO_FRAMES
+ | FLAG_HAS_WOL
+ | FLAG_APME_IN_CTRL3
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_CTRLEXT_ON_LOAD
+ | FLAG_TARC_SPEED_MODE_BIT, /* errata */
+ .pba = 38,
+ .get_variants = e1000_get_variants_82571,
+ .mac_ops = &e82571_mac_ops,
+ .phy_ops = &e82_phy_ops_igp,
+ .nvm_ops = &e82571_nvm_ops,
+};
+
+struct e1000_info e1000_82573_info = {
+ .mac = e1000_82573,
+ .flags = FLAG_HAS_HW_VLAN_FILTER
+ | FLAG_HAS_JUMBO_FRAMES
+ | FLAG_HAS_WOL
+ | FLAG_APME_IN_CTRL3
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_SMART_POWER_DOWN
+ | FLAG_HAS_AMT
+ | FLAG_HAS_ERT
+ | FLAG_HAS_SWSM_ON_LOAD,
+ .pba = 20,
+ .get_variants = e1000_get_variants_82571,
+ .mac_ops = &e82571_mac_ops,
+ .phy_ops = &e82_phy_ops_m88,
+ .nvm_ops = &e82571_nvm_ops,
+};
+
+struct e1000_info e1000_82574_info = {
+ .mac = e1000_82574,
+ .flags = FLAG_HAS_HW_VLAN_FILTER
+ | FLAG_HAS_MSIX
+ | FLAG_HAS_JUMBO_FRAMES
+ | FLAG_HAS_WOL
+ | FLAG_APME_IN_CTRL3
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_SMART_POWER_DOWN
+ | FLAG_HAS_AMT
+ | FLAG_HAS_CTRLEXT_ON_LOAD,
+ .pba = 20,
+ .get_variants = e1000_get_variants_82571,
+ .mac_ops = &e82571_mac_ops,
+ .phy_ops = &e82_phy_ops_bm,
+ .nvm_ops = &e82571_nvm_ops,
+};
+
--- /dev/null
+################################################################################
+#
+# Intel PRO/1000 Linux driver
+# Copyright(c) 1999 - 2008 Intel Corporation.
+#
+# This program is free software; you can redistribute it and/or modify it
+# under the terms and conditions of the GNU General Public License,
+# version 2, as published by the Free Software Foundation.
+#
+# This program is distributed in the hope it will be useful, but WITHOUT
+# ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+# FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+# more details.
+#
+# You should have received a copy of the GNU General Public License along with
+# this program; if not, write to the Free Software Foundation, Inc.,
+# 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+#
+# The full GNU General Public License is included in this distribution in
+# the file called "COPYING".
+#
+# Contact Information:
+# Linux NICS <linux.nics@intel.com>
+# e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+# Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+#
+################################################################################
+
+#
+# Makefile for the Intel(R) PRO/1000 ethernet driver
+#
+
+obj-$(CONFIG_E1000E) += e1000e.o
+
+e1000e-objs := 82571.o ich8lan.o es2lan.o \
+ lib.o phy.o param.o ethtool.o netdev.o
+
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2008 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#ifndef _E1000_DEFINES_H_
+#define _E1000_DEFINES_H_
+
+#define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */
+#define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */
+#define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */
+#define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */
+#define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */
+#define E1000_TXD_CMD_RS 0x08000000 /* Report Status */
+#define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */
+#define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */
+#define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */
+#define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */
+#define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */
+#define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */
+#define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */
+#define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */
+#define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */
+#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */
+#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */
+#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */
+
+/* Number of Transmit and Receive Descriptors must be a multiple of 8 */
+#define REQ_TX_DESCRIPTOR_MULTIPLE 8
+#define REQ_RX_DESCRIPTOR_MULTIPLE 8
+
+/* Definitions for power management and wakeup registers */
+/* Wake Up Control */
+#define E1000_WUC_APME 0x00000001 /* APM Enable */
+#define E1000_WUC_PME_EN 0x00000002 /* PME Enable */
+
+/* Wake Up Filter Control */
+#define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
+#define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */
+#define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */
+#define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */
+#define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */
+#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */
+
+/* Extended Device Control */
+#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Definable Pin 7 */
+#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
+#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */
+#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
+#define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000
+#define E1000_CTRL_EXT_EIAME 0x01000000
+#define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */
+#define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */
+#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */
+#define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */
+
+/* Receive Descriptor bit definitions */
+#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
+#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
+#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
+#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
+#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */
+#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
+#define E1000_RXD_ERR_CE 0x01 /* CRC Error */
+#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */
+#define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */
+#define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */
+#define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */
+#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */
+#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */
+
+#define E1000_RXDEXT_STATERR_CE 0x01000000
+#define E1000_RXDEXT_STATERR_SE 0x02000000
+#define E1000_RXDEXT_STATERR_SEQ 0x04000000
+#define E1000_RXDEXT_STATERR_CXE 0x10000000
+#define E1000_RXDEXT_STATERR_RXE 0x80000000
+
+/* mask to determine if packets should be dropped due to frame errors */
+#define E1000_RXD_ERR_FRAME_ERR_MASK ( \
+ E1000_RXD_ERR_CE | \
+ E1000_RXD_ERR_SE | \
+ E1000_RXD_ERR_SEQ | \
+ E1000_RXD_ERR_CXE | \
+ E1000_RXD_ERR_RXE)
+
+/* Same mask, but for extended and packet split descriptors */
+#define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \
+ E1000_RXDEXT_STATERR_CE | \
+ E1000_RXDEXT_STATERR_SE | \
+ E1000_RXDEXT_STATERR_SEQ | \
+ E1000_RXDEXT_STATERR_CXE | \
+ E1000_RXDEXT_STATERR_RXE)
+
+#define E1000_RXDPS_HDRSTAT_HDRSP 0x00008000
+
+/* Management Control */
+#define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */
+#define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */
+#define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */
+#define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */
+#define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */
+/* Enable MAC address filtering */
+#define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000
+/* Enable MNG packets to host memory */
+#define E1000_MANC_EN_MNG2HOST 0x00200000
+
+/* Receive Control */
+#define E1000_RCTL_EN 0x00000002 /* enable */
+#define E1000_RCTL_SBP 0x00000004 /* store bad packet */
+#define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */
+#define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */
+#define E1000_RCTL_LPE 0x00000020 /* long packet enable */
+#define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */
+#define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */
+#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
+#define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */
+#define E1000_RCTL_RDMTS_HALF 0x00000000 /* Rx desc min threshold size */
+#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
+#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
+/* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */
+#define E1000_RCTL_SZ_2048 0x00000000 /* Rx buffer size 2048 */
+#define E1000_RCTL_SZ_1024 0x00010000 /* Rx buffer size 1024 */
+#define E1000_RCTL_SZ_512 0x00020000 /* Rx buffer size 512 */
+#define E1000_RCTL_SZ_256 0x00030000 /* Rx buffer size 256 */
+/* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */
+#define E1000_RCTL_SZ_16384 0x00010000 /* Rx buffer size 16384 */
+#define E1000_RCTL_SZ_8192 0x00020000 /* Rx buffer size 8192 */
+#define E1000_RCTL_SZ_4096 0x00030000 /* Rx buffer size 4096 */
+#define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */
+#define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */
+#define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */
+#define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */
+#define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */
+
+/*
+ * Use byte values for the following shift parameters
+ * Usage:
+ * psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) &
+ * E1000_PSRCTL_BSIZE0_MASK) |
+ * ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) &
+ * E1000_PSRCTL_BSIZE1_MASK) |
+ * ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) &
+ * E1000_PSRCTL_BSIZE2_MASK) |
+ * ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |;
+ * E1000_PSRCTL_BSIZE3_MASK))
+ * where value0 = [128..16256], default=256
+ * value1 = [1024..64512], default=4096
+ * value2 = [0..64512], default=4096
+ * value3 = [0..64512], default=0
+ */
+
+#define E1000_PSRCTL_BSIZE0_MASK 0x0000007F
+#define E1000_PSRCTL_BSIZE1_MASK 0x00003F00
+#define E1000_PSRCTL_BSIZE2_MASK 0x003F0000
+#define E1000_PSRCTL_BSIZE3_MASK 0x3F000000
+
+#define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */
+#define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */
+#define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */
+#define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */
+
+/* SWFW_SYNC Definitions */
+#define E1000_SWFW_EEP_SM 0x1
+#define E1000_SWFW_PHY0_SM 0x2
+#define E1000_SWFW_PHY1_SM 0x4
+#define E1000_SWFW_CSR_SM 0x8
+
+/* Device Control */
+#define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */
+#define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */
+#define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */
+#define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */
+#define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */
+#define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */
+#define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */
+#define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */
+#define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */
+#define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */
+#define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */
+#define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */
+#define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */
+#define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */
+#define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */
+#define E1000_CTRL_RST 0x04000000 /* Global reset */
+#define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */
+#define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */
+#define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */
+#define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */
+
+/*
+ * Bit definitions for the Management Data IO (MDIO) and Management Data
+ * Clock (MDC) pins in the Device Control Register.
+ */
+
+/* Device Status */
+#define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */
+#define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */
+#define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */
+#define E1000_STATUS_FUNC_SHIFT 2
+#define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */
+#define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */
+#define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */
+#define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */
+#define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */
+#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion by NVM */
+#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
+
+/* Constants used to interpret the masked PCI-X bus speed. */
+
+#define HALF_DUPLEX 1
+#define FULL_DUPLEX 2
+
+
+#define ADVERTISE_10_HALF 0x0001
+#define ADVERTISE_10_FULL 0x0002
+#define ADVERTISE_100_HALF 0x0004
+#define ADVERTISE_100_FULL 0x0008
+#define ADVERTISE_1000_HALF 0x0010 /* Not used, just FYI */
+#define ADVERTISE_1000_FULL 0x0020
+
+/* 1000/H is not supported, nor spec-compliant. */
+#define E1000_ALL_SPEED_DUPLEX ( ADVERTISE_10_HALF | ADVERTISE_10_FULL | \
+ ADVERTISE_100_HALF | ADVERTISE_100_FULL | \
+ ADVERTISE_1000_FULL)
+#define E1000_ALL_NOT_GIG ( ADVERTISE_10_HALF | ADVERTISE_10_FULL | \
+ ADVERTISE_100_HALF | ADVERTISE_100_FULL)
+#define E1000_ALL_100_SPEED (ADVERTISE_100_HALF | ADVERTISE_100_FULL)
+#define E1000_ALL_10_SPEED (ADVERTISE_10_HALF | ADVERTISE_10_FULL)
+#define E1000_ALL_HALF_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_100_HALF)
+
+#define AUTONEG_ADVERTISE_SPEED_DEFAULT E1000_ALL_SPEED_DUPLEX
+
+/* LED Control */
+#define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F
+#define E1000_LEDCTL_LED0_MODE_SHIFT 0
+#define E1000_LEDCTL_LED0_IVRT 0x00000040
+#define E1000_LEDCTL_LED0_BLINK 0x00000080
+
+#define E1000_LEDCTL_MODE_LED_ON 0xE
+#define E1000_LEDCTL_MODE_LED_OFF 0xF
+
+/* Transmit Descriptor bit definitions */
+#define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */
+#define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */
+#define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */
+#define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */
+#define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */
+#define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */
+#define E1000_TXD_CMD_RS 0x08000000 /* Report Status */
+#define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */
+#define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */
+#define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */
+#define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */
+#define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */
+#define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */
+#define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */
+#define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */
+#define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */
+#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */
+#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */
+#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */
+
+/* Transmit Control */
+#define E1000_TCTL_EN 0x00000002 /* enable Tx */
+#define E1000_TCTL_PSP 0x00000008 /* pad short packets */
+#define E1000_TCTL_CT 0x00000ff0 /* collision threshold */
+#define E1000_TCTL_COLD 0x003ff000 /* collision distance */
+#define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */
+#define E1000_TCTL_MULR 0x10000000 /* Multiple request support */
+
+/* Transmit Arbitration Count */
+
+/* SerDes Control */
+#define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400
+
+/* Receive Checksum Control */
+#define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */
+#define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */
+
+/* Header split receive */
+#define E1000_RFCTL_ACK_DIS 0x00001000
+#define E1000_RFCTL_EXTEN 0x00008000
+#define E1000_RFCTL_IPV6_EX_DIS 0x00010000
+#define E1000_RFCTL_NEW_IPV6_EXT_DIS 0x00020000
+
+/* Collision related configuration parameters */
+#define E1000_COLLISION_THRESHOLD 15
+#define E1000_CT_SHIFT 4
+#define E1000_COLLISION_DISTANCE 63
+#define E1000_COLD_SHIFT 12
+
+/* Default values for the transmit IPG register */
+#define DEFAULT_82543_TIPG_IPGT_COPPER 8
+
+#define E1000_TIPG_IPGT_MASK 0x000003FF
+
+#define DEFAULT_82543_TIPG_IPGR1 8
+#define E1000_TIPG_IPGR1_SHIFT 10
+
+#define DEFAULT_82543_TIPG_IPGR2 6
+#define DEFAULT_80003ES2LAN_TIPG_IPGR2 7
+#define E1000_TIPG_IPGR2_SHIFT 20
+
+#define MAX_JUMBO_FRAME_SIZE 0x3F00
+
+/* Extended Configuration Control and Size */
+#define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020
+#define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE 0x00000001
+#define E1000_EXTCNF_CTRL_SWFLAG 0x00000020
+#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK 0x00FF0000
+#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT 16
+#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK 0x0FFF0000
+#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT 16
+
+#define E1000_PHY_CTRL_D0A_LPLU 0x00000002
+#define E1000_PHY_CTRL_NOND0A_LPLU 0x00000004
+#define E1000_PHY_CTRL_NOND0A_GBE_DISABLE 0x00000008
+#define E1000_PHY_CTRL_GBE_DISABLE 0x00000040
+
+#define E1000_KABGTXD_BGSQLBIAS 0x00050000
+
+/* PBA constants */
+#define E1000_PBA_8K 0x0008 /* 8KB */
+#define E1000_PBA_16K 0x0010 /* 16KB */
+
+#define E1000_PBS_16K E1000_PBA_16K
+
+#define IFS_MAX 80
+#define IFS_MIN 40
+#define IFS_RATIO 4
+#define IFS_STEP 10
+#define MIN_NUM_XMITS 1000
+
+/* SW Semaphore Register */
+#define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */
+#define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */
+#define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */
+
+/* Interrupt Cause Read */
+#define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */
+#define E1000_ICR_LSC 0x00000004 /* Link Status Change */
+#define E1000_ICR_RXSEQ 0x00000008 /* Rx sequence error */
+#define E1000_ICR_RXDMT0 0x00000010 /* Rx desc min. threshold (0) */
+#define E1000_ICR_RXT0 0x00000080 /* Rx timer intr (ring 0) */
+#define E1000_ICR_INT_ASSERTED 0x80000000 /* If this bit asserted, the driver should claim the interrupt */
+#define E1000_ICR_RXQ0 0x00100000 /* Rx Queue 0 Interrupt */
+#define E1000_ICR_RXQ1 0x00200000 /* Rx Queue 1 Interrupt */
+#define E1000_ICR_TXQ0 0x00400000 /* Tx Queue 0 Interrupt */
+#define E1000_ICR_TXQ1 0x00800000 /* Tx Queue 1 Interrupt */
+#define E1000_ICR_OTHER 0x01000000 /* Other Interrupts */
+
+/* PBA ECC Register */
+#define E1000_PBA_ECC_COUNTER_MASK 0xFFF00000 /* ECC counter mask */
+#define E1000_PBA_ECC_COUNTER_SHIFT 20 /* ECC counter shift value */
+#define E1000_PBA_ECC_CORR_EN 0x00000001 /* ECC correction enable */
+#define E1000_PBA_ECC_STAT_CLR 0x00000002 /* Clear ECC error counter */
+#define E1000_PBA_ECC_INT_EN 0x00000004 /* Enable ICR bit 5 for ECC */
+
+/*
+ * This defines the bits that are set in the Interrupt Mask
+ * Set/Read Register. Each bit is documented below:
+ * o RXT0 = Receiver Timer Interrupt (ring 0)
+ * o TXDW = Transmit Descriptor Written Back
+ * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0)
+ * o RXSEQ = Receive Sequence Error
+ * o LSC = Link Status Change
+ */
+#define IMS_ENABLE_MASK ( \
+ E1000_IMS_RXT0 | \
+ E1000_IMS_TXDW | \
+ E1000_IMS_RXDMT0 | \
+ E1000_IMS_RXSEQ | \
+ E1000_IMS_LSC)
+
+/* Interrupt Mask Set */
+#define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
+#define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */
+#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* Rx sequence error */
+#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* Rx desc min. threshold */
+#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* Rx timer intr */
+#define E1000_IMS_RXQ0 E1000_ICR_RXQ0 /* Rx Queue 0 Interrupt */
+#define E1000_IMS_RXQ1 E1000_ICR_RXQ1 /* Rx Queue 1 Interrupt */
+#define E1000_IMS_TXQ0 E1000_ICR_TXQ0 /* Tx Queue 0 Interrupt */
+#define E1000_IMS_TXQ1 E1000_ICR_TXQ1 /* Tx Queue 1 Interrupt */
+#define E1000_IMS_OTHER E1000_ICR_OTHER /* Other Interrupts */
+
+/* Interrupt Cause Set */
+#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
+#define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
+#define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* Rx sequence error */
+#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* Rx desc min. threshold */
+
+/* Transmit Descriptor Control */
+#define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */
+#define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */
+#define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */
+#define E1000_TXDCTL_MAX_TX_DESC_PREFETCH 0x0100001F /* GRAN=1, PTHRESH=31 */
+/* Enable the counting of desc. still to be processed. */
+#define E1000_TXDCTL_COUNT_DESC 0x00400000
+
+/* Flow Control Constants */
+#define FLOW_CONTROL_ADDRESS_LOW 0x00C28001
+#define FLOW_CONTROL_ADDRESS_HIGH 0x00000100
+#define FLOW_CONTROL_TYPE 0x8808
+
+/* 802.1q VLAN Packet Size */
+#define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */
+
+/* Receive Address */
+/*
+ * Number of high/low register pairs in the RAR. The RAR (Receive Address
+ * Registers) holds the directed and multicast addresses that we monitor.
+ * Technically, we have 16 spots. However, we reserve one of these spots
+ * (RAR[15]) for our directed address used by controllers with
+ * manageability enabled, allowing us room for 15 multicast addresses.
+ */
+#define E1000_RAR_ENTRIES 15
+#define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */
+
+/* Error Codes */
+#define E1000_ERR_NVM 1
+#define E1000_ERR_PHY 2
+#define E1000_ERR_CONFIG 3
+#define E1000_ERR_PARAM 4
+#define E1000_ERR_MAC_INIT 5
+#define E1000_ERR_PHY_TYPE 6
+#define E1000_ERR_RESET 9
+#define E1000_ERR_MASTER_REQUESTS_PENDING 10
+#define E1000_ERR_HOST_INTERFACE_COMMAND 11
+#define E1000_BLK_PHY_RESET 12
+#define E1000_ERR_SWFW_SYNC 13
+#define E1000_NOT_IMPLEMENTED 14
+
+/* Loop limit on how long we wait for auto-negotiation to complete */
+#define FIBER_LINK_UP_LIMIT 50
+#define COPPER_LINK_UP_LIMIT 10
+#define PHY_AUTO_NEG_LIMIT 45
+#define PHY_FORCE_LIMIT 20
+/* Number of 100 microseconds we wait for PCI Express master disable */
+#define MASTER_DISABLE_TIMEOUT 800
+/* Number of milliseconds we wait for PHY configuration done after MAC reset */
+#define PHY_CFG_TIMEOUT 100
+/* Number of 2 milliseconds we wait for acquiring MDIO ownership. */
+#define MDIO_OWNERSHIP_TIMEOUT 10
+/* Number of milliseconds for NVM auto read done after MAC reset. */
+#define AUTO_READ_DONE_TIMEOUT 10
+
+/* Flow Control */
+#define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */
+
+/* Transmit Configuration Word */
+#define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */
+#define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */
+#define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */
+#define E1000_TXCW_PAUSE_MASK 0x00000180 /* TXCW pause request mask */
+#define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */
+
+/* Receive Configuration Word */
+#define E1000_RXCW_IV 0x08000000 /* Receive config invalid */
+#define E1000_RXCW_C 0x20000000 /* Receive config */
+#define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */
+
+/* PCI Express Control */
+#define E1000_GCR_RXD_NO_SNOOP 0x00000001
+#define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002
+#define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004
+#define E1000_GCR_TXD_NO_SNOOP 0x00000008
+#define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010
+#define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020
+
+#define PCIE_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \
+ E1000_GCR_RXDSCW_NO_SNOOP | \
+ E1000_GCR_RXDSCR_NO_SNOOP | \
+ E1000_GCR_TXD_NO_SNOOP | \
+ E1000_GCR_TXDSCW_NO_SNOOP | \
+ E1000_GCR_TXDSCR_NO_SNOOP)
+
+/* PHY Control Register */
+#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */
+#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */
+#define MII_CR_POWER_DOWN 0x0800 /* Power down */
+#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */
+#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */
+#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */
+#define MII_CR_SPEED_1000 0x0040
+#define MII_CR_SPEED_100 0x2000
+#define MII_CR_SPEED_10 0x0000
+
+/* PHY Status Register */
+#define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */
+#define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */
+
+/* Autoneg Advertisement Register */
+#define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */
+#define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */
+#define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */
+#define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */
+#define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */
+#define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */
+
+/* Link Partner Ability Register (Base Page) */
+#define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */
+#define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */
+
+/* Autoneg Expansion Register */
+#define NWAY_ER_LP_NWAY_CAPS 0x0001 /* LP has Auto Neg Capability */
+
+/* 1000BASE-T Control Register */
+#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */
+#define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */
+ /* 0=DTE device */
+#define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */
+ /* 0=Configure PHY as Slave */
+#define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */
+ /* 0=Automatic Master/Slave config */
+
+/* 1000BASE-T Status Register */
+#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
+#define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */
+
+
+/* PHY 1000 MII Register/Bit Definitions */
+/* PHY Registers defined by IEEE */
+#define PHY_CONTROL 0x00 /* Control Register */
+#define PHY_STATUS 0x01 /* Status Register */
+#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */
+#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */
+#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
+#define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */
+#define PHY_AUTONEG_EXP 0x06 /* Autoneg Expansion Reg */
+#define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */
+#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
+#define PHY_EXT_STATUS 0x0F /* Extended Status Reg */
+
+/* NVM Control */
+#define E1000_EECD_SK 0x00000001 /* NVM Clock */
+#define E1000_EECD_CS 0x00000002 /* NVM Chip Select */
+#define E1000_EECD_DI 0x00000004 /* NVM Data In */
+#define E1000_EECD_DO 0x00000008 /* NVM Data Out */
+#define E1000_EECD_REQ 0x00000040 /* NVM Access Request */
+#define E1000_EECD_GNT 0x00000080 /* NVM Access Grant */
+#define E1000_EECD_PRES 0x00000100 /* NVM Present */
+#define E1000_EECD_SIZE 0x00000200 /* NVM Size (0=64 word 1=256 word) */
+/* NVM Addressing bits based on type (0-small, 1-large) */
+#define E1000_EECD_ADDR_BITS 0x00000400
+#define E1000_NVM_GRANT_ATTEMPTS 1000 /* NVM # attempts to gain grant */
+#define E1000_EECD_AUTO_RD 0x00000200 /* NVM Auto Read done */
+#define E1000_EECD_SIZE_EX_MASK 0x00007800 /* NVM Size */
+#define E1000_EECD_SIZE_EX_SHIFT 11
+#define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */
+#define E1000_EECD_AUPDEN 0x00100000 /* Enable Autonomous FLASH update */
+#define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */
+
+#define E1000_NVM_RW_REG_DATA 16 /* Offset to data in NVM read/write registers */
+#define E1000_NVM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */
+#define E1000_NVM_RW_REG_START 1 /* Start operation */
+#define E1000_NVM_RW_ADDR_SHIFT 2 /* Shift to the address bits */
+#define E1000_NVM_POLL_WRITE 1 /* Flag for polling for write complete */
+#define E1000_NVM_POLL_READ 0 /* Flag for polling for read complete */
+#define E1000_FLASH_UPDATES 2000
+
+/* NVM Word Offsets */
+#define NVM_ID_LED_SETTINGS 0x0004
+#define NVM_INIT_CONTROL2_REG 0x000F
+#define NVM_INIT_CONTROL3_PORT_B 0x0014
+#define NVM_INIT_3GIO_3 0x001A
+#define NVM_INIT_CONTROL3_PORT_A 0x0024
+#define NVM_CFG 0x0012
+#define NVM_ALT_MAC_ADDR_PTR 0x0037
+#define NVM_CHECKSUM_REG 0x003F
+
+#define E1000_NVM_CFG_DONE_PORT_0 0x40000 /* MNG config cycle done */
+#define E1000_NVM_CFG_DONE_PORT_1 0x80000 /* ...for second port */
+
+/* Mask bits for fields in Word 0x0f of the NVM */
+#define NVM_WORD0F_PAUSE_MASK 0x3000
+#define NVM_WORD0F_PAUSE 0x1000
+#define NVM_WORD0F_ASM_DIR 0x2000
+
+/* Mask bits for fields in Word 0x1a of the NVM */
+#define NVM_WORD1A_ASPM_MASK 0x000C
+
+/* For checksumming, the sum of all words in the NVM should equal 0xBABA. */
+#define NVM_SUM 0xBABA
+
+/* PBA (printed board assembly) number words */
+#define NVM_PBA_OFFSET_0 8
+#define NVM_PBA_OFFSET_1 9
+
+#define NVM_WORD_SIZE_BASE_SHIFT 6
+
+/* NVM Commands - SPI */
+#define NVM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */
+#define NVM_READ_OPCODE_SPI 0x03 /* NVM read opcode */
+#define NVM_WRITE_OPCODE_SPI 0x02 /* NVM write opcode */
+#define NVM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */
+#define NVM_WREN_OPCODE_SPI 0x06 /* NVM set Write Enable latch */
+#define NVM_RDSR_OPCODE_SPI 0x05 /* NVM read Status register */
+
+/* SPI NVM Status Register */
+#define NVM_STATUS_RDY_SPI 0x01
+
+/* Word definitions for ID LED Settings */
+#define ID_LED_RESERVED_0000 0x0000
+#define ID_LED_RESERVED_FFFF 0xFFFF
+#define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \
+ (ID_LED_OFF1_OFF2 << 8) | \
+ (ID_LED_DEF1_DEF2 << 4) | \
+ (ID_LED_DEF1_DEF2))
+#define ID_LED_DEF1_DEF2 0x1
+#define ID_LED_DEF1_ON2 0x2
+#define ID_LED_DEF1_OFF2 0x3
+#define ID_LED_ON1_DEF2 0x4
+#define ID_LED_ON1_ON2 0x5
+#define ID_LED_ON1_OFF2 0x6
+#define ID_LED_OFF1_DEF2 0x7
+#define ID_LED_OFF1_ON2 0x8
+#define ID_LED_OFF1_OFF2 0x9
+
+#define IGP_ACTIVITY_LED_MASK 0xFFFFF0FF
+#define IGP_ACTIVITY_LED_ENABLE 0x0300
+#define IGP_LED3_MODE 0x07000000
+
+/* PCI/PCI-X/PCI-EX Config space */
+#define PCI_HEADER_TYPE_REGISTER 0x0E
+#define PCIE_LINK_STATUS 0x12
+
+#define PCI_HEADER_TYPE_MULTIFUNC 0x80
+#define PCIE_LINK_WIDTH_MASK 0x3F0
+#define PCIE_LINK_WIDTH_SHIFT 4
+
+#define PHY_REVISION_MASK 0xFFFFFFF0
+#define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */
+#define MAX_PHY_MULTI_PAGE_REG 0xF
+
+/* Bit definitions for valid PHY IDs. */
+/*
+ * I = Integrated
+ * E = External
+ */
+#define M88E1000_E_PHY_ID 0x01410C50
+#define M88E1000_I_PHY_ID 0x01410C30
+#define M88E1011_I_PHY_ID 0x01410C20
+#define IGP01E1000_I_PHY_ID 0x02A80380
+#define M88E1111_I_PHY_ID 0x01410CC0
+#define GG82563_E_PHY_ID 0x01410CA0
+#define IGP03E1000_E_PHY_ID 0x02A80390
+#define IFE_E_PHY_ID 0x02A80330
+#define IFE_PLUS_E_PHY_ID 0x02A80320
+#define IFE_C_E_PHY_ID 0x02A80310
+#define BME1000_E_PHY_ID 0x01410CB0
+#define BME1000_E_PHY_ID_R2 0x01410CB1
+
+/* M88E1000 Specific Registers */
+#define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */
+#define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */
+#define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */
+
+#define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */
+#define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */
+
+/* M88E1000 PHY Specific Control Register */
+#define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */
+#define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */
+ /* Manual MDI configuration */
+#define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */
+/* 1000BASE-T: Auto crossover, 100BASE-TX/10BASE-T: MDI Mode */
+#define M88E1000_PSCR_AUTO_X_1000T 0x0040
+/* Auto crossover enabled all speeds */
+#define M88E1000_PSCR_AUTO_X_MODE 0x0060
+/*
+ * 1=Enable Extended 10BASE-T distance (Lower 10BASE-T Rx Threshold)
+ * 0=Normal 10BASE-T Rx Threshold
+ */
+#define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
+
+/* M88E1000 PHY Specific Status Register */
+#define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */
+#define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */
+#define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */
+/* 0=<50M; 1=50-80M; 2=80-110M; 3=110-140M; 4=>140M */
+#define M88E1000_PSSR_CABLE_LENGTH 0x0380
+#define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */
+#define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */
+
+#define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7
+
+/*
+ * Number of times we will attempt to autonegotiate before downshifting if we
+ * are the master
+ */
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00
+#define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 0x0000
+/*
+ * Number of times we will attempt to autonegotiate before downshifting if we
+ * are the slave
+ */
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK 0x0300
+#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100
+#define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */
+
+/* M88EC018 Rev 2 specific DownShift settings */
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00
+#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800
+
+/* BME1000 PHY Specific Control Register */
+#define BME1000_PSCR_ENABLE_DOWNSHIFT 0x0800 /* 1 = enable downshift */
+
+
+#define PHY_PAGE_SHIFT 5
+#define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \
+ ((reg) & MAX_PHY_REG_ADDRESS))
+
+/*
+ * Bits...
+ * 15-5: page
+ * 4-0: register offset
+ */
+#define GG82563_PAGE_SHIFT 5
+#define GG82563_REG(page, reg) \
+ (((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS))
+#define GG82563_MIN_ALT_REG 30
+
+/* GG82563 Specific Registers */
+#define GG82563_PHY_SPEC_CTRL \
+ GG82563_REG(0, 16) /* PHY Specific Control */
+#define GG82563_PHY_PAGE_SELECT \
+ GG82563_REG(0, 22) /* Page Select */
+#define GG82563_PHY_SPEC_CTRL_2 \
+ GG82563_REG(0, 26) /* PHY Specific Control 2 */
+#define GG82563_PHY_PAGE_SELECT_ALT \
+ GG82563_REG(0, 29) /* Alternate Page Select */
+
+#define GG82563_PHY_MAC_SPEC_CTRL \
+ GG82563_REG(2, 21) /* MAC Specific Control Register */
+
+#define GG82563_PHY_DSP_DISTANCE \
+ GG82563_REG(5, 26) /* DSP Distance */
+
+/* Page 193 - Port Control Registers */
+#define GG82563_PHY_KMRN_MODE_CTRL \
+ GG82563_REG(193, 16) /* Kumeran Mode Control */
+#define GG82563_PHY_PWR_MGMT_CTRL \
+ GG82563_REG(193, 20) /* Power Management Control */
+
+/* Page 194 - KMRN Registers */
+#define GG82563_PHY_INBAND_CTRL \
+ GG82563_REG(194, 18) /* Inband Control */
+
+/* MDI Control */
+#define E1000_MDIC_REG_SHIFT 16
+#define E1000_MDIC_PHY_SHIFT 21
+#define E1000_MDIC_OP_WRITE 0x04000000
+#define E1000_MDIC_OP_READ 0x08000000
+#define E1000_MDIC_READY 0x10000000
+#define E1000_MDIC_ERROR 0x40000000
+
+/* SerDes Control */
+#define E1000_GEN_POLL_TIMEOUT 640
+
+#endif /* _E1000_DEFINES_H_ */
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2008 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+/* Linux PRO/1000 Ethernet Driver main header file */
+
+#ifndef _E1000_H_
+#define _E1000_H_
+
+#include <linux/types.h>
+#include <linux/timer.h>
+#include <linux/workqueue.h>
+#include <linux/io.h>
+#include <linux/netdevice.h>
+
+#include "e1000_compat.h"
+#include "hw.h"
+
+struct e1000_info;
+
+#define e_printk(level, adapter, format, arg...) \
+ printk(level "%s: " format, \
+ adapter->netdev->name, ## arg)
+
+#ifdef DEBUG
+#define e_dbg(format, arg...) \
+ e_printk(KERN_DEBUG , adapter, format, ## arg)
+#else
+#define e_dbg(format, arg...) do { (void)(adapter); } while (0)
+#endif
+
+#define e_err(format, arg...) \
+ e_printk(KERN_ERR, adapter, format, ## arg)
+#define e_info(format, arg...) \
+ e_printk(KERN_INFO, adapter, format, ## arg)
+#define e_warn(format, arg...) \
+ e_printk(KERN_WARNING, adapter, format, ## arg)
+#define e_notice(format, arg...) \
+ e_printk(KERN_NOTICE, adapter, format, ## arg)
+
+
+/* Interrupt modes, as used by the IntMode paramter */
+#define E1000E_INT_MODE_LEGACY 0
+#define E1000E_INT_MODE_MSI 1
+#define E1000E_INT_MODE_MSIX 2
+
+/* Tx/Rx descriptor defines */
+#define E1000_DEFAULT_TXD 256
+#define E1000_MAX_TXD 4096
+#define E1000_MIN_TXD 64
+
+#define E1000_DEFAULT_RXD 256
+#define E1000_MAX_RXD 4096
+#define E1000_MIN_RXD 64
+
+#define E1000_MIN_ITR_USECS 10 /* 100000 irq/sec */
+#define E1000_MAX_ITR_USECS 10000 /* 100 irq/sec */
+
+/* Early Receive defines */
+#define E1000_ERT_2048 0x100
+
+#define E1000_FC_PAUSE_TIME 0x0680 /* 858 usec */
+
+/* How many Tx Descriptors do we need to call netif_wake_queue ? */
+/* How many Rx Buffers do we bundle into one write to the hardware ? */
+#define E1000_RX_BUFFER_WRITE 16 /* Must be power of 2 */
+
+#define AUTO_ALL_MODES 0
+#define E1000_EEPROM_APME 0x0400
+
+#define E1000_MNG_VLAN_NONE (-1)
+
+/* Number of packet split data buffers (not including the header buffer) */
+#define PS_PAGE_BUFFERS (MAX_PS_BUFFERS - 1)
+
+enum e1000_boards {
+ board_82571,
+ board_82572,
+ board_82573,
+ board_82574,
+ board_80003es2lan,
+ board_ich8lan,
+ board_ich9lan,
+ board_ich10lan,
+};
+
+struct e1000_queue_stats {
+ u64 packets;
+ u64 bytes;
+};
+
+struct e1000_ps_page {
+ struct page *page;
+ u64 dma; /* must be u64 - written to hw */
+};
+
+/*
+ * wrappers around a pointer to a socket buffer,
+ * so a DMA handle can be stored along with the buffer
+ */
+struct e1000_buffer {
+ dma_addr_t dma;
+ struct sk_buff *skb;
+ union {
+ /* Tx */
+ struct {
+ unsigned long time_stamp;
+ u16 length;
+ u16 next_to_watch;
+ };
+ /* Rx */
+ /* arrays of page information for packet split */
+ struct e1000_ps_page *ps_pages;
+ };
+ struct page *page;
+};
+
+struct e1000_ring {
+ void *desc; /* pointer to ring memory */
+ dma_addr_t dma; /* phys address of ring */
+ unsigned int size; /* length of ring in bytes */
+ unsigned int count; /* number of desc. in ring */
+
+ u16 next_to_use;
+ u16 next_to_clean;
+
+ u16 head;
+ u16 tail;
+
+ /* array of buffer information structs */
+ struct e1000_buffer *buffer_info;
+
+ char name[IFNAMSIZ + 5];
+ u32 ims_val;
+ u32 itr_val;
+ u16 itr_register;
+ int set_itr;
+
+ struct sk_buff *rx_skb_top;
+
+ struct e1000_queue_stats stats;
+};
+
+/* PHY register snapshot values */
+struct e1000_phy_regs {
+ u16 bmcr; /* basic mode control register */
+ u16 bmsr; /* basic mode status register */
+ u16 advertise; /* auto-negotiation advertisement */
+ u16 lpa; /* link partner ability register */
+ u16 expansion; /* auto-negotiation expansion reg */
+ u16 ctrl1000; /* 1000BASE-T control register */
+ u16 stat1000; /* 1000BASE-T status register */
+ u16 estatus; /* extended status register */
+};
+
+/* board specific private data structure */
+struct e1000_adapter {
+ struct timer_list watchdog_timer;
+ struct timer_list phy_info_timer;
+ struct timer_list blink_timer;
+
+ struct work_struct reset_task;
+ struct work_struct watchdog_task;
+
+ const struct e1000_info *ei;
+
+ struct vlan_group *vlgrp;
+ u32 bd_number;
+ u32 rx_buffer_len;
+ u16 mng_vlan_id;
+ u16 link_speed;
+ u16 link_duplex;
+
+ spinlock_t tx_queue_lock; /* prevent concurrent tail updates */
+
+ /* track device up/down/testing state */
+ unsigned long state;
+
+ /* Interrupt Throttle Rate */
+ u32 itr;
+ u32 itr_setting;
+ u16 tx_itr;
+ u16 rx_itr;
+
+ /*
+ * Tx
+ */
+ struct e1000_ring *tx_ring /* One per active queue */
+ ____cacheline_aligned_in_smp;
+
+ unsigned long tx_queue_len;
+ unsigned int restart_queue;
+ u32 txd_cmd;
+
+ bool detect_tx_hung;
+ u8 tx_timeout_factor;
+
+ u32 tx_int_delay;
+ u32 tx_abs_int_delay;
+
+ unsigned int total_tx_bytes;
+ unsigned int total_tx_packets;
+ unsigned int total_rx_bytes;
+ unsigned int total_rx_packets;
+
+ /* Tx stats */
+ u64 tpt_old;
+ u64 colc_old;
+ u32 gotc;
+ u64 gotc_old;
+ u32 tx_timeout_count;
+ u32 tx_fifo_head;
+ u32 tx_head_addr;
+ u32 tx_fifo_size;
+ u32 tx_dma_failed;
+
+ /*
+ * Rx
+ */
+ bool (*clean_rx) (struct e1000_adapter *adapter,
+ int *work_done, int work_to_do)
+ ____cacheline_aligned_in_smp;
+ void (*alloc_rx_buf) (struct e1000_adapter *adapter,
+ int cleaned_count);
+ struct e1000_ring *rx_ring;
+
+ u32 rx_int_delay;
+ u32 rx_abs_int_delay;
+
+ /* Rx stats */
+ u64 hw_csum_err;
+ u64 hw_csum_good;
+ u64 rx_hdr_split;
+ u32 gorc;
+ u64 gorc_old;
+ u32 alloc_rx_buff_failed;
+ u32 rx_dma_failed;
+
+ unsigned int rx_ps_pages;
+ u16 rx_ps_bsize0;
+ u32 max_frame_size;
+ u32 min_frame_size;
+
+ /* OS defined structs */
+ struct net_device *netdev;
+ struct pci_dev *pdev;
+ struct net_device_stats net_stats;
+ spinlock_t stats_lock; /* prevent concurrent stats updates */
+
+ /* structs defined in e1000_hw.h */
+ struct e1000_hw hw;
+
+ struct e1000_hw_stats stats;
+ struct e1000_phy_info phy_info;
+ struct e1000_phy_stats phy_stats;
+
+ /* Snapshot of PHY registers */
+ struct e1000_phy_regs phy_regs;
+
+ struct e1000_ring test_tx_ring;
+ struct e1000_ring test_rx_ring;
+ u32 test_icr;
+
+ u32 msg_enable;
+ struct msix_entry *msix_entries;
+ int int_mode;
+ u32 eiac_mask;
+
+ u32 eeprom_wol;
+ u32 wol;
+ u32 pba;
+
+ bool fc_autoneg;
+
+ unsigned long led_status;
+
+ unsigned int flags;
+};
+
+struct e1000_info {
+ enum e1000_mac_type mac;
+ unsigned int flags;
+ u32 pba;
+ s32 (*get_variants)(struct e1000_adapter *);
+ struct e1000_mac_operations *mac_ops;
+ struct e1000_phy_operations *phy_ops;
+ struct e1000_nvm_operations *nvm_ops;
+};
+
+/* hardware capability, feature, and workaround flags */
+#define FLAG_HAS_AMT (1 << 0)
+#define FLAG_HAS_FLASH (1 << 1)
+#define FLAG_HAS_HW_VLAN_FILTER (1 << 2)
+#define FLAG_HAS_WOL (1 << 3)
+#define FLAG_HAS_ERT (1 << 4)
+#define FLAG_HAS_CTRLEXT_ON_LOAD (1 << 5)
+#define FLAG_HAS_SWSM_ON_LOAD (1 << 6)
+#define FLAG_HAS_JUMBO_FRAMES (1 << 7)
+#define FLAG_READ_ONLY_NVM (1 << 8)
+#define FLAG_IS_ICH (1 << 9)
+#define FLAG_HAS_MSIX (1 << 10)
+#define FLAG_HAS_SMART_POWER_DOWN (1 << 11)
+#define FLAG_IS_QUAD_PORT_A (1 << 12)
+#define FLAG_IS_QUAD_PORT (1 << 13)
+#define FLAG_TIPG_MEDIUM_FOR_80003ESLAN (1 << 14)
+#define FLAG_APME_IN_WUC (1 << 15)
+#define FLAG_APME_IN_CTRL3 (1 << 16)
+#define FLAG_APME_CHECK_PORT_B (1 << 17)
+#define FLAG_DISABLE_FC_PAUSE_TIME (1 << 18)
+#define FLAG_NO_WAKE_UCAST (1 << 19)
+#define FLAG_MNG_PT_ENABLED (1 << 20)
+#define FLAG_RESET_OVERWRITES_LAA (1 << 21)
+#define FLAG_TARC_SPEED_MODE_BIT (1 << 22)
+#define FLAG_TARC_SET_BIT_ZERO (1 << 23)
+#define FLAG_RX_NEEDS_RESTART (1 << 24)
+#define FLAG_LSC_GIG_SPEED_DROP (1 << 25)
+#define FLAG_SMART_POWER_DOWN (1 << 26)
+#define FLAG_MSI_ENABLED (1 << 27)
+#define FLAG_RX_CSUM_ENABLED (1 << 28)
+#define FLAG_TSO_FORCE (1 << 29)
+#define FLAG_MSI_TEST_FAILED (1 << 30)
+#define FLAG_RX_RESTART_NOW (1 << 31)
+
+#define E1000_RX_DESC_PS(R, i) \
+ (&(((union e1000_rx_desc_packet_split *)((R).desc))[i]))
+#define E1000_GET_DESC(R, i, type) (&(((struct type *)((R).desc))[i]))
+#define E1000_RX_DESC(R, i) E1000_GET_DESC(R, i, e1000_rx_desc)
+#define E1000_TX_DESC(R, i) E1000_GET_DESC(R, i, e1000_tx_desc)
+#define E1000_CONTEXT_DESC(R, i) E1000_GET_DESC(R, i, e1000_context_desc)
+
+enum e1000_state_t {
+ __E1000_TESTING,
+ __E1000_RESETTING,
+ __E1000_DOWN
+};
+
+enum latency_range {
+ lowest_latency = 0,
+ low_latency = 1,
+ bulk_latency = 2,
+ latency_invalid = 255
+};
+
+extern char e1000e_driver_name[];
+extern const char e1000e_driver_version[];
+
+extern void e1000e_check_options(struct e1000_adapter *adapter);
+extern void e1000e_set_ethtool_ops(struct net_device *netdev);
+
+extern int e1000e_up(struct e1000_adapter *adapter);
+extern void e1000e_down(struct e1000_adapter *adapter);
+extern void e1000e_reinit_locked(struct e1000_adapter *adapter);
+extern void e1000e_reset(struct e1000_adapter *adapter);
+extern void e1000e_power_up_phy(struct e1000_adapter *adapter);
+extern int e1000e_setup_rx_resources(struct e1000_adapter *adapter);
+extern int e1000e_setup_tx_resources(struct e1000_adapter *adapter);
+extern void e1000e_free_rx_resources(struct e1000_adapter *adapter);
+extern void e1000e_free_tx_resources(struct e1000_adapter *adapter);
+extern void e1000e_update_stats(struct e1000_adapter *adapter);
+extern void e1000e_set_interrupt_capability(struct e1000_adapter *adapter);
+extern void e1000e_reset_interrupt_capability(struct e1000_adapter *adapter);
+
+extern unsigned int copybreak;
+
+extern char *e1000e_get_hw_dev_name(struct e1000_hw *hw);
+
+extern struct e1000_info e1000_82571_info;
+extern struct e1000_info e1000_82572_info;
+extern struct e1000_info e1000_82573_info;
+extern struct e1000_info e1000_82574_info;
+extern struct e1000_info e1000_ich8_info;
+extern struct e1000_info e1000_ich9_info;
+extern struct e1000_info e1000_ich10_info;
+extern struct e1000_info e1000_es2_info;
+
+extern s32 e1000e_read_pba_num(struct e1000_hw *hw, u32 *pba_num);
+
+extern s32 e1000e_commit_phy(struct e1000_hw *hw);
+
+extern bool e1000e_enable_mng_pass_thru(struct e1000_hw *hw);
+
+extern bool e1000e_get_laa_state_82571(struct e1000_hw *hw);
+extern void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state);
+
+extern void e1000e_write_protect_nvm_ich8lan(struct e1000_hw *hw);
+extern void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw,
+ bool state);
+extern void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw);
+extern void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw);
+extern void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw);
+
+extern s32 e1000e_check_for_copper_link(struct e1000_hw *hw);
+extern s32 e1000e_check_for_fiber_link(struct e1000_hw *hw);
+extern s32 e1000e_check_for_serdes_link(struct e1000_hw *hw);
+extern s32 e1000e_cleanup_led_generic(struct e1000_hw *hw);
+extern s32 e1000e_led_on_generic(struct e1000_hw *hw);
+extern s32 e1000e_led_off_generic(struct e1000_hw *hw);
+extern s32 e1000e_get_bus_info_pcie(struct e1000_hw *hw);
+extern s32 e1000e_get_speed_and_duplex_copper(struct e1000_hw *hw, u16 *speed, u16 *duplex);
+extern s32 e1000e_get_speed_and_duplex_fiber_serdes(struct e1000_hw *hw, u16 *speed, u16 *duplex);
+extern s32 e1000e_disable_pcie_master(struct e1000_hw *hw);
+extern s32 e1000e_get_auto_rd_done(struct e1000_hw *hw);
+extern s32 e1000e_id_led_init(struct e1000_hw *hw);
+extern void e1000e_clear_hw_cntrs_base(struct e1000_hw *hw);
+extern s32 e1000e_setup_fiber_serdes_link(struct e1000_hw *hw);
+extern s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw);
+extern s32 e1000e_copper_link_setup_igp(struct e1000_hw *hw);
+extern s32 e1000e_setup_link(struct e1000_hw *hw);
+extern void e1000e_clear_vfta(struct e1000_hw *hw);
+extern void e1000e_init_rx_addrs(struct e1000_hw *hw, u16 rar_count);
+extern void e1000e_update_mc_addr_list_generic(struct e1000_hw *hw,
+ u8 *mc_addr_list,
+ u32 mc_addr_count,
+ u32 rar_used_count,
+ u32 rar_count);
+extern void e1000e_rar_set(struct e1000_hw *hw, u8 *addr, u32 index);
+extern s32 e1000e_set_fc_watermarks(struct e1000_hw *hw);
+extern void e1000e_set_pcie_no_snoop(struct e1000_hw *hw, u32 no_snoop);
+extern s32 e1000e_get_hw_semaphore(struct e1000_hw *hw);
+extern s32 e1000e_valid_led_default(struct e1000_hw *hw, u16 *data);
+extern void e1000e_config_collision_dist(struct e1000_hw *hw);
+extern s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw);
+extern s32 e1000e_force_mac_fc(struct e1000_hw *hw);
+extern s32 e1000e_blink_led(struct e1000_hw *hw);
+extern void e1000e_write_vfta(struct e1000_hw *hw, u32 offset, u32 value);
+extern void e1000e_reset_adaptive(struct e1000_hw *hw);
+extern void e1000e_update_adaptive(struct e1000_hw *hw);
+
+extern s32 e1000e_setup_copper_link(struct e1000_hw *hw);
+extern s32 e1000e_get_phy_id(struct e1000_hw *hw);
+extern void e1000e_put_hw_semaphore(struct e1000_hw *hw);
+extern s32 e1000e_check_reset_block_generic(struct e1000_hw *hw);
+extern s32 e1000e_phy_force_speed_duplex_igp(struct e1000_hw *hw);
+extern s32 e1000e_get_cable_length_igp_2(struct e1000_hw *hw);
+extern s32 e1000e_get_phy_info_igp(struct e1000_hw *hw);
+extern s32 e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data);
+extern s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw);
+extern s32 e1000e_set_d3_lplu_state(struct e1000_hw *hw, bool active);
+extern s32 e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data);
+extern s32 e1000e_phy_sw_reset(struct e1000_hw *hw);
+extern s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw);
+extern s32 e1000e_get_cfg_done(struct e1000_hw *hw);
+extern s32 e1000e_get_cable_length_m88(struct e1000_hw *hw);
+extern s32 e1000e_get_phy_info_m88(struct e1000_hw *hw);
+extern s32 e1000e_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data);
+extern s32 e1000e_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data);
+extern s32 e1000e_phy_init_script_igp3(struct e1000_hw *hw);
+extern enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id);
+extern s32 e1000e_determine_phy_address(struct e1000_hw *hw);
+extern s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data);
+extern s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data);
+extern s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data);
+extern s32 e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data);
+extern void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl);
+extern s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data);
+extern s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data);
+extern s32 e1000e_phy_has_link_generic(struct e1000_hw *hw, u32 iterations,
+ u32 usec_interval, bool *success);
+extern s32 e1000e_phy_reset_dsp(struct e1000_hw *hw);
+extern s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
+extern s32 e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
+extern s32 e1000e_check_downshift(struct e1000_hw *hw);
+
+static inline s32 e1000_phy_hw_reset(struct e1000_hw *hw)
+{
+ return hw->phy.ops.reset_phy(hw);
+}
+
+static inline s32 e1000_check_reset_block(struct e1000_hw *hw)
+{
+ return hw->phy.ops.check_reset_block(hw);
+}
+
+static inline s32 e1e_rphy(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return hw->phy.ops.read_phy_reg(hw, offset, data);
+}
+
+static inline s32 e1e_wphy(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return hw->phy.ops.write_phy_reg(hw, offset, data);
+}
+
+static inline s32 e1000_get_cable_length(struct e1000_hw *hw)
+{
+ return hw->phy.ops.get_cable_length(hw);
+}
+
+extern s32 e1000e_acquire_nvm(struct e1000_hw *hw);
+extern s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data);
+extern s32 e1000e_update_nvm_checksum_generic(struct e1000_hw *hw);
+extern s32 e1000e_poll_eerd_eewr_done(struct e1000_hw *hw, int ee_reg);
+extern s32 e1000e_read_nvm_eerd(struct e1000_hw *hw, u16 offset, u16 words, u16 *data);
+extern s32 e1000e_validate_nvm_checksum_generic(struct e1000_hw *hw);
+extern void e1000e_release_nvm(struct e1000_hw *hw);
+extern void e1000e_reload_nvm(struct e1000_hw *hw);
+extern s32 e1000e_read_mac_addr(struct e1000_hw *hw);
+
+static inline s32 e1000_validate_nvm_checksum(struct e1000_hw *hw)
+{
+ return hw->nvm.ops.validate_nvm(hw);
+}
+
+static inline s32 e1000e_update_nvm_checksum(struct e1000_hw *hw)
+{
+ return hw->nvm.ops.update_nvm(hw);
+}
+
+static inline s32 e1000_read_nvm(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
+{
+ return hw->nvm.ops.read_nvm(hw, offset, words, data);
+}
+
+static inline s32 e1000_write_nvm(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
+{
+ return hw->nvm.ops.write_nvm(hw, offset, words, data);
+}
+
+static inline s32 e1000_get_phy_info(struct e1000_hw *hw)
+{
+ return hw->phy.ops.get_phy_info(hw);
+}
+
+static inline s32 e1000e_check_mng_mode(struct e1000_hw *hw)
+{
+ return hw->mac.ops.check_mng_mode(hw);
+}
+
+extern bool e1000e_check_mng_mode_generic(struct e1000_hw *hw);
+extern bool e1000e_enable_tx_pkt_filtering(struct e1000_hw *hw);
+extern s32 e1000e_mng_write_dhcp_info(struct e1000_hw *hw, u8 *buffer, u16 length);
+
+static inline u32 __er32(struct e1000_hw *hw, unsigned long reg)
+{
+ return readl(hw->hw_addr + reg);
+}
+
+static inline void __ew32(struct e1000_hw *hw, unsigned long reg, u32 val)
+{
+ writel(val, hw->hw_addr + reg);
+}
+
+#endif /* _E1000_H_ */
--- /dev/null
+#ifndef __E1000E_COMPAT_H__
+#define __E1000E_COMPAT_H__
+
+#include <linux/if_vlan.h>
+#include <linux/pci.h>
+
+typedef unsigned int bool;
+
+#define ETH_FCS_LEN 4
+
+static inline struct net_device *vlan_group_get_device(struct vlan_group *vg,
+ int vlan_id)
+{
+ return vg->vlan_devices[vlan_id];
+}
+
+static inline void vlan_group_set_device(struct vlan_group *vg, int vlan_id,
+ struct net_device *dev)
+{
+ vg->vlan_devices[vlan_id] = NULL;
+}
+/* generic boolean compatibility */
+#define true 1
+#define false 0
+
+/*
+ * backport csum_unfold and datatypes from 2.6.25
+ */
+typedef __u16 __bitwise __sum16;
+typedef __u32 __bitwise __wsum;
+
+static inline __wsum csum_unfold(__sum16 n)
+{
+ return (__force __wsum)n;
+};
+
+#ifndef CHECKSUM_PARTIAL
+#define CHECKSUM_PARTIAL CHECKSUM_HW
+#define CHECKSUM_COMPLETE CHECKSUM_HW
+#endif
+
+#define skb_tail_pointer(skb) skb->tail
+#define skb_copy_to_linear_data_offset(skb, offset, from, len) \
+ memcpy(skb->data + offset, from, len)
+
+
+static inline int pci_channel_offline(struct pci_dev *pdev)
+{
+ return (pdev->error_state != pci_channel_io_normal);
+}
+#ifndef round_jiffies
+#define round_jiffies(x) x
+#endif
+
+#define tcp_hdr(skb) (skb->h.th)
+#define tcp_hdrlen(skb) (skb->h.th->doff << 2)
+#define skb_transport_offset(skb) (skb->h.raw - skb->data)
+#define skb_transport_header(skb) (skb->h.raw)
+#define ipv6_hdr(skb) (skb->nh.ipv6h)
+#define ip_hdr(skb) (skb->nh.iph)
+#define skb_network_offset(skb) (skb->nh.raw - skb->data)
+
+#ifndef PCI_VDEVICE
+#define PCI_VDEVICE(ven, dev) \
+ PCI_VENDOR_ID_##ven, (dev), \
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0
+#endif
+
+#endif
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2008 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+/*
+ * 80003ES2LAN Gigabit Ethernet Controller (Copper)
+ * 80003ES2LAN Gigabit Ethernet Controller (Serdes)
+ */
+
+#include <linux/netdevice.h>
+#include <linux/ethtool.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+
+#include "e1000.h"
+
+#define E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL 0x00
+#define E1000_KMRNCTRLSTA_OFFSET_INB_CTRL 0x02
+#define E1000_KMRNCTRLSTA_OFFSET_HD_CTRL 0x10
+#define E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE 0x1F
+
+#define E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS 0x0008
+#define E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS 0x0800
+#define E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING 0x0010
+
+#define E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT 0x0004
+#define E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT 0x0000
+#define E1000_KMRNCTRLSTA_OPMODE_E_IDLE 0x2000
+
+#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */
+#define DEFAULT_TCTL_EXT_GCEX_80003ES2LAN 0x00010000
+
+#define DEFAULT_TIPG_IPGT_1000_80003ES2LAN 0x8
+#define DEFAULT_TIPG_IPGT_10_100_80003ES2LAN 0x9
+
+/* GG82563 PHY Specific Status Register (Page 0, Register 16 */
+#define GG82563_PSCR_POLARITY_REVERSAL_DISABLE 0x0002 /* 1=Reversal Disab. */
+#define GG82563_PSCR_CROSSOVER_MODE_MASK 0x0060
+#define GG82563_PSCR_CROSSOVER_MODE_MDI 0x0000 /* 00=Manual MDI */
+#define GG82563_PSCR_CROSSOVER_MODE_MDIX 0x0020 /* 01=Manual MDIX */
+#define GG82563_PSCR_CROSSOVER_MODE_AUTO 0x0060 /* 11=Auto crossover */
+
+/* PHY Specific Control Register 2 (Page 0, Register 26) */
+#define GG82563_PSCR2_REVERSE_AUTO_NEG 0x2000
+ /* 1=Reverse Auto-Negotiation */
+
+/* MAC Specific Control Register (Page 2, Register 21) */
+/* Tx clock speed for Link Down and 1000BASE-T for the following speeds */
+#define GG82563_MSCR_TX_CLK_MASK 0x0007
+#define GG82563_MSCR_TX_CLK_10MBPS_2_5 0x0004
+#define GG82563_MSCR_TX_CLK_100MBPS_25 0x0005
+#define GG82563_MSCR_TX_CLK_1000MBPS_25 0x0007
+
+#define GG82563_MSCR_ASSERT_CRS_ON_TX 0x0010 /* 1=Assert */
+
+/* DSP Distance Register (Page 5, Register 26) */
+#define GG82563_DSPD_CABLE_LENGTH 0x0007 /* 0 = <50M
+ 1 = 50-80M
+ 2 = 80-110M
+ 3 = 110-140M
+ 4 = >140M */
+
+/* Kumeran Mode Control Register (Page 193, Register 16) */
+#define GG82563_KMCR_PASS_FALSE_CARRIER 0x0800
+
+/* Max number of times Kumeran read/write should be validated */
+#define GG82563_MAX_KMRN_RETRY 0x5
+
+/* Power Management Control Register (Page 193, Register 20) */
+#define GG82563_PMCR_ENABLE_ELECTRICAL_IDLE 0x0001
+ /* 1=Enable SERDES Electrical Idle */
+
+/* In-Band Control Register (Page 194, Register 18) */
+#define GG82563_ICR_DIS_PADDING 0x0010 /* Disable Padding */
+
+/*
+ * A table for the GG82563 cable length where the range is defined
+ * with a lower bound at "index" and the upper bound at
+ * "index + 5".
+ */
+static const u16 e1000_gg82563_cable_length_table[] =
+ { 0, 60, 115, 150, 150, 60, 115, 150, 180, 180, 0xFF };
+
+static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw);
+static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask);
+static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask);
+static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw);
+static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw);
+static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw);
+static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex);
+
+/**
+ * e1000_init_phy_params_80003es2lan - Init ESB2 PHY func ptrs.
+ * @hw: pointer to the HW structure
+ *
+ * This is a function pointer entry point called by the api module.
+ **/
+static s32 e1000_init_phy_params_80003es2lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+
+ if (hw->phy.media_type != e1000_media_type_copper) {
+ phy->type = e1000_phy_none;
+ return 0;
+ }
+
+ phy->addr = 1;
+ phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+ phy->reset_delay_us = 100;
+ phy->type = e1000_phy_gg82563;
+
+ /* This can only be done after all function pointers are setup. */
+ ret_val = e1000e_get_phy_id(hw);
+
+ /* Verify phy id */
+ if (phy->id != GG82563_E_PHY_ID)
+ return -E1000_ERR_PHY;
+
+ return ret_val;
+}
+
+/**
+ * e1000_init_nvm_params_80003es2lan - Init ESB2 NVM func ptrs.
+ * @hw: pointer to the HW structure
+ *
+ * This is a function pointer entry point called by the api module.
+ **/
+static s32 e1000_init_nvm_params_80003es2lan(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ u32 eecd = er32(EECD);
+ u16 size;
+
+ nvm->opcode_bits = 8;
+ nvm->delay_usec = 1;
+ switch (nvm->override) {
+ case e1000_nvm_override_spi_large:
+ nvm->page_size = 32;
+ nvm->address_bits = 16;
+ break;
+ case e1000_nvm_override_spi_small:
+ nvm->page_size = 8;
+ nvm->address_bits = 8;
+ break;
+ default:
+ nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8;
+ nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8;
+ break;
+ }
+
+ nvm->type = e1000_nvm_eeprom_spi;
+
+ size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
+ E1000_EECD_SIZE_EX_SHIFT);
+
+ /*
+ * Added to a constant, "size" becomes the left-shift value
+ * for setting word_size.
+ */
+ size += NVM_WORD_SIZE_BASE_SHIFT;
+
+ /* EEPROM access above 16k is unsupported */
+ if (size > 14)
+ size = 14;
+ nvm->word_size = 1 << size;
+
+ return 0;
+}
+
+/**
+ * e1000_init_mac_params_80003es2lan - Init ESB2 MAC func ptrs.
+ * @hw: pointer to the HW structure
+ *
+ * This is a function pointer entry point called by the api module.
+ **/
+static s32 e1000_init_mac_params_80003es2lan(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_mac_info *mac = &hw->mac;
+ struct e1000_mac_operations *func = &mac->ops;
+
+ /* Set media type */
+ switch (adapter->pdev->device) {
+ case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
+ hw->phy.media_type = e1000_media_type_internal_serdes;
+ break;
+ default:
+ hw->phy.media_type = e1000_media_type_copper;
+ break;
+ }
+
+ /* Set mta register count */
+ mac->mta_reg_count = 128;
+ /* Set rar entry count */
+ mac->rar_entry_count = E1000_RAR_ENTRIES;
+ /* Set if manageability features are enabled. */
+ mac->arc_subsystem_valid = (er32(FWSM) & E1000_FWSM_MODE_MASK) ? 1 : 0;
+
+ /* check for link */
+ switch (hw->phy.media_type) {
+ case e1000_media_type_copper:
+ func->setup_physical_interface = e1000_setup_copper_link_80003es2lan;
+ func->check_for_link = e1000e_check_for_copper_link;
+ break;
+ case e1000_media_type_fiber:
+ func->setup_physical_interface = e1000e_setup_fiber_serdes_link;
+ func->check_for_link = e1000e_check_for_fiber_link;
+ break;
+ case e1000_media_type_internal_serdes:
+ func->setup_physical_interface = e1000e_setup_fiber_serdes_link;
+ func->check_for_link = e1000e_check_for_serdes_link;
+ break;
+ default:
+ return -E1000_ERR_CONFIG;
+ break;
+ }
+
+ return 0;
+}
+
+static s32 e1000_get_variants_80003es2lan(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ s32 rc;
+
+ rc = e1000_init_mac_params_80003es2lan(adapter);
+ if (rc)
+ return rc;
+
+ rc = e1000_init_nvm_params_80003es2lan(hw);
+ if (rc)
+ return rc;
+
+ rc = e1000_init_phy_params_80003es2lan(hw);
+ if (rc)
+ return rc;
+
+ return 0;
+}
+
+/**
+ * e1000_acquire_phy_80003es2lan - Acquire rights to access PHY
+ * @hw: pointer to the HW structure
+ *
+ * A wrapper to acquire access rights to the correct PHY. This is a
+ * function pointer entry point called by the api module.
+ **/
+static s32 e1000_acquire_phy_80003es2lan(struct e1000_hw *hw)
+{
+ u16 mask;
+
+ mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM;
+ mask |= E1000_SWFW_CSR_SM;
+
+ return e1000_acquire_swfw_sync_80003es2lan(hw, mask);
+}
+
+/**
+ * e1000_release_phy_80003es2lan - Release rights to access PHY
+ * @hw: pointer to the HW structure
+ *
+ * A wrapper to release access rights to the correct PHY. This is a
+ * function pointer entry point called by the api module.
+ **/
+static void e1000_release_phy_80003es2lan(struct e1000_hw *hw)
+{
+ u16 mask;
+
+ mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM;
+ mask |= E1000_SWFW_CSR_SM;
+
+ e1000_release_swfw_sync_80003es2lan(hw, mask);
+}
+
+/**
+ * e1000_acquire_nvm_80003es2lan - Acquire rights to access NVM
+ * @hw: pointer to the HW structure
+ *
+ * Acquire the semaphore to access the EEPROM. This is a function
+ * pointer entry point called by the api module.
+ **/
+static s32 e1000_acquire_nvm_80003es2lan(struct e1000_hw *hw)
+{
+ s32 ret_val;
+
+ ret_val = e1000_acquire_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000e_acquire_nvm(hw);
+
+ if (ret_val)
+ e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);
+
+ return ret_val;
+}
+
+/**
+ * e1000_release_nvm_80003es2lan - Relinquish rights to access NVM
+ * @hw: pointer to the HW structure
+ *
+ * Release the semaphore used to access the EEPROM. This is a
+ * function pointer entry point called by the api module.
+ **/
+static void e1000_release_nvm_80003es2lan(struct e1000_hw *hw)
+{
+ e1000e_release_nvm(hw);
+ e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);
+}
+
+/**
+ * e1000_acquire_swfw_sync_80003es2lan - Acquire SW/FW semaphore
+ * @hw: pointer to the HW structure
+ * @mask: specifies which semaphore to acquire
+ *
+ * Acquire the SW/FW semaphore to access the PHY or NVM. The mask
+ * will also specify which port we're acquiring the lock for.
+ **/
+static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask)
+{
+ u32 swfw_sync;
+ u32 swmask = mask;
+ u32 fwmask = mask << 16;
+ s32 i = 0;
+ s32 timeout = 200;
+
+ while (i < timeout) {
+ if (e1000e_get_hw_semaphore(hw))
+ return -E1000_ERR_SWFW_SYNC;
+
+ swfw_sync = er32(SW_FW_SYNC);
+ if (!(swfw_sync & (fwmask | swmask)))
+ break;
+
+ /*
+ * Firmware currently using resource (fwmask)
+ * or other software thread using resource (swmask)
+ */
+ e1000e_put_hw_semaphore(hw);
+ mdelay(5);
+ i++;
+ }
+
+ if (i == timeout) {
+ hw_dbg(hw,
+ "Driver can't access resource, SW_FW_SYNC timeout.\n");
+ return -E1000_ERR_SWFW_SYNC;
+ }
+
+ swfw_sync |= swmask;
+ ew32(SW_FW_SYNC, swfw_sync);
+
+ e1000e_put_hw_semaphore(hw);
+
+ return 0;
+}
+
+/**
+ * e1000_release_swfw_sync_80003es2lan - Release SW/FW semaphore
+ * @hw: pointer to the HW structure
+ * @mask: specifies which semaphore to acquire
+ *
+ * Release the SW/FW semaphore used to access the PHY or NVM. The mask
+ * will also specify which port we're releasing the lock for.
+ **/
+static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask)
+{
+ u32 swfw_sync;
+
+ while (e1000e_get_hw_semaphore(hw) != 0);
+ /* Empty */
+
+ swfw_sync = er32(SW_FW_SYNC);
+ swfw_sync &= ~mask;
+ ew32(SW_FW_SYNC, swfw_sync);
+
+ e1000e_put_hw_semaphore(hw);
+}
+
+/**
+ * e1000_read_phy_reg_gg82563_80003es2lan - Read GG82563 PHY register
+ * @hw: pointer to the HW structure
+ * @offset: offset of the register to read
+ * @data: pointer to the data returned from the operation
+ *
+ * Read the GG82563 PHY register. This is a function pointer entry
+ * point called by the api module.
+ **/
+static s32 e1000_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
+ u32 offset, u16 *data)
+{
+ s32 ret_val;
+ u32 page_select;
+ u16 temp;
+
+ ret_val = e1000_acquire_phy_80003es2lan(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Select Configuration Page */
+ if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
+ page_select = GG82563_PHY_PAGE_SELECT;
+ } else {
+ /*
+ * Use Alternative Page Select register to access
+ * registers 30 and 31
+ */
+ page_select = GG82563_PHY_PAGE_SELECT_ALT;
+ }
+
+ temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT);
+ ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp);
+ if (ret_val) {
+ e1000_release_phy_80003es2lan(hw);
+ return ret_val;
+ }
+
+ /*
+ * The "ready" bit in the MDIC register may be incorrectly set
+ * before the device has completed the "Page Select" MDI
+ * transaction. So we wait 200us after each MDI command...
+ */
+ udelay(200);
+
+ /* ...and verify the command was successful. */
+ ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);
+
+ if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
+ ret_val = -E1000_ERR_PHY;
+ e1000_release_phy_80003es2lan(hw);
+ return ret_val;
+ }
+
+ udelay(200);
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+ udelay(200);
+ e1000_release_phy_80003es2lan(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_write_phy_reg_gg82563_80003es2lan - Write GG82563 PHY register
+ * @hw: pointer to the HW structure
+ * @offset: offset of the register to read
+ * @data: value to write to the register
+ *
+ * Write to the GG82563 PHY register. This is a function pointer entry
+ * point called by the api module.
+ **/
+static s32 e1000_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
+ u32 offset, u16 data)
+{
+ s32 ret_val;
+ u32 page_select;
+ u16 temp;
+
+ ret_val = e1000_acquire_phy_80003es2lan(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Select Configuration Page */
+ if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
+ page_select = GG82563_PHY_PAGE_SELECT;
+ } else {
+ /*
+ * Use Alternative Page Select register to access
+ * registers 30 and 31
+ */
+ page_select = GG82563_PHY_PAGE_SELECT_ALT;
+ }
+
+ temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT);
+ ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp);
+ if (ret_val) {
+ e1000_release_phy_80003es2lan(hw);
+ return ret_val;
+ }
+
+
+ /*
+ * The "ready" bit in the MDIC register may be incorrectly set
+ * before the device has completed the "Page Select" MDI
+ * transaction. So we wait 200us after each MDI command...
+ */
+ udelay(200);
+
+ /* ...and verify the command was successful. */
+ ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);
+
+ if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
+ e1000_release_phy_80003es2lan(hw);
+ return -E1000_ERR_PHY;
+ }
+
+ udelay(200);
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+ udelay(200);
+ e1000_release_phy_80003es2lan(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_write_nvm_80003es2lan - Write to ESB2 NVM
+ * @hw: pointer to the HW structure
+ * @offset: offset of the register to read
+ * @words: number of words to write
+ * @data: buffer of data to write to the NVM
+ *
+ * Write "words" of data to the ESB2 NVM. This is a function
+ * pointer entry point called by the api module.
+ **/
+static s32 e1000_write_nvm_80003es2lan(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data)
+{
+ return e1000e_write_nvm_spi(hw, offset, words, data);
+}
+
+/**
+ * e1000_get_cfg_done_80003es2lan - Wait for configuration to complete
+ * @hw: pointer to the HW structure
+ *
+ * Wait a specific amount of time for manageability processes to complete.
+ * This is a function pointer entry point called by the phy module.
+ **/
+static s32 e1000_get_cfg_done_80003es2lan(struct e1000_hw *hw)
+{
+ s32 timeout = PHY_CFG_TIMEOUT;
+ u32 mask = E1000_NVM_CFG_DONE_PORT_0;
+
+ if (hw->bus.func == 1)
+ mask = E1000_NVM_CFG_DONE_PORT_1;
+
+ while (timeout) {
+ if (er32(EEMNGCTL) & mask)
+ break;
+ msleep(1);
+ timeout--;
+ }
+ if (!timeout) {
+ hw_dbg(hw, "MNG configuration cycle has not completed.\n");
+ return -E1000_ERR_RESET;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_phy_force_speed_duplex_80003es2lan - Force PHY speed and duplex
+ * @hw: pointer to the HW structure
+ *
+ * Force the speed and duplex settings onto the PHY. This is a
+ * function pointer entry point called by the phy module.
+ **/
+static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 phy_data;
+ bool link;
+
+ /*
+ * Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
+ * forced whenever speed and duplex are forced.
+ */
+ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_AUTO;
+ ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ hw_dbg(hw, "GG82563 PSCR: %X\n", phy_data);
+
+ ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
+
+ /* Reset the phy to commit changes. */
+ phy_data |= MII_CR_RESET;
+
+ ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ udelay(1);
+
+ if (hw->phy.autoneg_wait_to_complete) {
+ hw_dbg(hw, "Waiting for forced speed/duplex link "
+ "on GG82563 phy.\n");
+
+ ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
+ 100000, &link);
+ if (ret_val)
+ return ret_val;
+
+ if (!link) {
+ /*
+ * We didn't get link.
+ * Reset the DSP and cross our fingers.
+ */
+ ret_val = e1000e_phy_reset_dsp(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Try once more */
+ ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
+ 100000, &link);
+ if (ret_val)
+ return ret_val;
+ }
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Resetting the phy means we need to verify the TX_CLK corresponds
+ * to the link speed. 10Mbps -> 2.5MHz, else 25MHz.
+ */
+ phy_data &= ~GG82563_MSCR_TX_CLK_MASK;
+ if (hw->mac.forced_speed_duplex & E1000_ALL_10_SPEED)
+ phy_data |= GG82563_MSCR_TX_CLK_10MBPS_2_5;
+ else
+ phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25;
+
+ /*
+ * In addition, we must re-enable CRS on Tx for both half and full
+ * duplex.
+ */
+ phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
+ ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL, phy_data);
+
+ return ret_val;
+}
+
+/**
+ * e1000_get_cable_length_80003es2lan - Set approximate cable length
+ * @hw: pointer to the HW structure
+ *
+ * Find the approximate cable length as measured by the GG82563 PHY.
+ * This is a function pointer entry point called by the phy module.
+ **/
+static s32 e1000_get_cable_length_80003es2lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+ u16 index;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_DSP_DISTANCE, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ index = phy_data & GG82563_DSPD_CABLE_LENGTH;
+ phy->min_cable_length = e1000_gg82563_cable_length_table[index];
+ phy->max_cable_length = e1000_gg82563_cable_length_table[index+5];
+
+ phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2;
+
+ return 0;
+}
+
+/**
+ * e1000_get_link_up_info_80003es2lan - Report speed and duplex
+ * @hw: pointer to the HW structure
+ * @speed: pointer to speed buffer
+ * @duplex: pointer to duplex buffer
+ *
+ * Retrieve the current speed and duplex configuration.
+ * This is a function pointer entry point called by the api module.
+ **/
+static s32 e1000_get_link_up_info_80003es2lan(struct e1000_hw *hw, u16 *speed,
+ u16 *duplex)
+{
+ s32 ret_val;
+
+ if (hw->phy.media_type == e1000_media_type_copper) {
+ ret_val = e1000e_get_speed_and_duplex_copper(hw,
+ speed,
+ duplex);
+ if (ret_val)
+ return ret_val;
+ if (*speed == SPEED_1000)
+ ret_val = e1000_cfg_kmrn_1000_80003es2lan(hw);
+ else
+ ret_val = e1000_cfg_kmrn_10_100_80003es2lan(hw,
+ *duplex);
+ } else {
+ ret_val = e1000e_get_speed_and_duplex_fiber_serdes(hw,
+ speed,
+ duplex);
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000_reset_hw_80003es2lan - Reset the ESB2 controller
+ * @hw: pointer to the HW structure
+ *
+ * Perform a global reset to the ESB2 controller.
+ * This is a function pointer entry point called by the api module.
+ **/
+static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ u32 icr;
+ s32 ret_val;
+
+ /*
+ * Prevent the PCI-E bus from sticking if there is no TLP connection
+ * on the last TLP read/write transaction when MAC is reset.
+ */
+ ret_val = e1000e_disable_pcie_master(hw);
+ if (ret_val)
+ hw_dbg(hw, "PCI-E Master disable polling has failed.\n");
+
+ hw_dbg(hw, "Masking off all interrupts\n");
+ ew32(IMC, 0xffffffff);
+
+ ew32(RCTL, 0);
+ ew32(TCTL, E1000_TCTL_PSP);
+ e1e_flush();
+
+ msleep(10);
+
+ ctrl = er32(CTRL);
+
+ hw_dbg(hw, "Issuing a global reset to MAC\n");
+ ew32(CTRL, ctrl | E1000_CTRL_RST);
+
+ ret_val = e1000e_get_auto_rd_done(hw);
+ if (ret_val)
+ /* We don't want to continue accessing MAC registers. */
+ return ret_val;
+
+ /* Clear any pending interrupt events. */
+ ew32(IMC, 0xffffffff);
+ icr = er32(ICR);
+
+ return 0;
+}
+
+/**
+ * e1000_init_hw_80003es2lan - Initialize the ESB2 controller
+ * @hw: pointer to the HW structure
+ *
+ * Initialize the hw bits, LED, VFTA, MTA, link and hw counters.
+ * This is a function pointer entry point called by the api module.
+ **/
+static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 reg_data;
+ s32 ret_val;
+ u16 i;
+
+ e1000_initialize_hw_bits_80003es2lan(hw);
+
+ /* Initialize identification LED */
+ ret_val = e1000e_id_led_init(hw);
+ if (ret_val) {
+ hw_dbg(hw, "Error initializing identification LED\n");
+ return ret_val;
+ }
+
+ /* Disabling VLAN filtering */
+ hw_dbg(hw, "Initializing the IEEE VLAN\n");
+ e1000e_clear_vfta(hw);
+
+ /* Setup the receive address. */
+ e1000e_init_rx_addrs(hw, mac->rar_entry_count);
+
+ /* Zero out the Multicast HASH table */
+ hw_dbg(hw, "Zeroing the MTA\n");
+ for (i = 0; i < mac->mta_reg_count; i++)
+ E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);
+
+ /* Setup link and flow control */
+ ret_val = e1000e_setup_link(hw);
+
+ /* Set the transmit descriptor write-back policy */
+ reg_data = er32(TXDCTL(0));
+ reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC;
+ ew32(TXDCTL(0), reg_data);
+
+ /* ...for both queues. */
+ reg_data = er32(TXDCTL(1));
+ reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC;
+ ew32(TXDCTL(1), reg_data);
+
+ /* Enable retransmit on late collisions */
+ reg_data = er32(TCTL);
+ reg_data |= E1000_TCTL_RTLC;
+ ew32(TCTL, reg_data);
+
+ /* Configure Gigabit Carry Extend Padding */
+ reg_data = er32(TCTL_EXT);
+ reg_data &= ~E1000_TCTL_EXT_GCEX_MASK;
+ reg_data |= DEFAULT_TCTL_EXT_GCEX_80003ES2LAN;
+ ew32(TCTL_EXT, reg_data);
+
+ /* Configure Transmit Inter-Packet Gap */
+ reg_data = er32(TIPG);
+ reg_data &= ~E1000_TIPG_IPGT_MASK;
+ reg_data |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN;
+ ew32(TIPG, reg_data);
+
+ reg_data = E1000_READ_REG_ARRAY(hw, E1000_FFLT, 0x0001);
+ reg_data &= ~0x00100000;
+ E1000_WRITE_REG_ARRAY(hw, E1000_FFLT, 0x0001, reg_data);
+
+ /*
+ * Clear all of the statistics registers (clear on read). It is
+ * important that we do this after we have tried to establish link
+ * because the symbol error count will increment wildly if there
+ * is no link.
+ */
+ e1000_clear_hw_cntrs_80003es2lan(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_initialize_hw_bits_80003es2lan - Init hw bits of ESB2
+ * @hw: pointer to the HW structure
+ *
+ * Initializes required hardware-dependent bits needed for normal operation.
+ **/
+static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw)
+{
+ u32 reg;
+
+ /* Transmit Descriptor Control 0 */
+ reg = er32(TXDCTL(0));
+ reg |= (1 << 22);
+ ew32(TXDCTL(0), reg);
+
+ /* Transmit Descriptor Control 1 */
+ reg = er32(TXDCTL(1));
+ reg |= (1 << 22);
+ ew32(TXDCTL(1), reg);
+
+ /* Transmit Arbitration Control 0 */
+ reg = er32(TARC(0));
+ reg &= ~(0xF << 27); /* 30:27 */
+ if (hw->phy.media_type != e1000_media_type_copper)
+ reg &= ~(1 << 20);
+ ew32(TARC(0), reg);
+
+ /* Transmit Arbitration Control 1 */
+ reg = er32(TARC(1));
+ if (er32(TCTL) & E1000_TCTL_MULR)
+ reg &= ~(1 << 28);
+ else
+ reg |= (1 << 28);
+ ew32(TARC(1), reg);
+}
+
+/**
+ * e1000_copper_link_setup_gg82563_80003es2lan - Configure GG82563 Link
+ * @hw: pointer to the HW structure
+ *
+ * Setup some GG82563 PHY registers for obtaining link
+ **/
+static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u32 ctrl_ext;
+ u32 i = 0;
+ u16 data, data2;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL, &data);
+ if (ret_val)
+ return ret_val;
+
+ data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
+ /* Use 25MHz for both link down and 1000Base-T for Tx clock. */
+ data |= GG82563_MSCR_TX_CLK_1000MBPS_25;
+
+ ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL, data);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Options:
+ * MDI/MDI-X = 0 (default)
+ * 0 - Auto for all speeds
+ * 1 - MDI mode
+ * 2 - MDI-X mode
+ * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
+ */
+ ret_val = e1e_rphy(hw, GG82563_PHY_SPEC_CTRL, &data);
+ if (ret_val)
+ return ret_val;
+
+ data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK;
+
+ switch (phy->mdix) {
+ case 1:
+ data |= GG82563_PSCR_CROSSOVER_MODE_MDI;
+ break;
+ case 2:
+ data |= GG82563_PSCR_CROSSOVER_MODE_MDIX;
+ break;
+ case 0:
+ default:
+ data |= GG82563_PSCR_CROSSOVER_MODE_AUTO;
+ break;
+ }
+
+ /*
+ * Options:
+ * disable_polarity_correction = 0 (default)
+ * Automatic Correction for Reversed Cable Polarity
+ * 0 - Disabled
+ * 1 - Enabled
+ */
+ data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
+ if (phy->disable_polarity_correction)
+ data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
+
+ ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL, data);
+ if (ret_val)
+ return ret_val;
+
+ /* SW Reset the PHY so all changes take effect */
+ ret_val = e1000e_commit_phy(hw);
+ if (ret_val) {
+ hw_dbg(hw, "Error Resetting the PHY\n");
+ return ret_val;
+ }
+
+ /* Bypass Rx and Tx FIFO's */
+ ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL,
+ E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS |
+ E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000e_read_kmrn_reg(hw,
+ E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE,
+ &data);
+ if (ret_val)
+ return ret_val;
+ data |= E1000_KMRNCTRLSTA_OPMODE_E_IDLE;
+ ret_val = e1000e_write_kmrn_reg(hw,
+ E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE,
+ data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_SPEC_CTRL_2, &data);
+ if (ret_val)
+ return ret_val;
+
+ data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG;
+ ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL_2, data);
+ if (ret_val)
+ return ret_val;
+
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext &= ~(E1000_CTRL_EXT_LINK_MODE_MASK);
+ ew32(CTRL_EXT, ctrl_ext);
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_PWR_MGMT_CTRL, &data);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Do not init these registers when the HW is in IAMT mode, since the
+ * firmware will have already initialized them. We only initialize
+ * them if the HW is not in IAMT mode.
+ */
+ if (!e1000e_check_mng_mode(hw)) {
+ /* Enable Electrical Idle on the PHY */
+ data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE;
+ ret_val = e1e_wphy(hw, GG82563_PHY_PWR_MGMT_CTRL, data);
+ if (ret_val)
+ return ret_val;
+
+ do {
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL,
+ &data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL,
+ &data2);
+ if (ret_val)
+ return ret_val;
+ i++;
+ } while ((data != data2) && (i < GG82563_MAX_KMRN_RETRY));
+
+ data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+ ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /*
+ * Workaround: Disable padding in Kumeran interface in the MAC
+ * and in the PHY to avoid CRC errors.
+ */
+ ret_val = e1e_rphy(hw, GG82563_PHY_INBAND_CTRL, &data);
+ if (ret_val)
+ return ret_val;
+
+ data |= GG82563_ICR_DIS_PADDING;
+ ret_val = e1e_wphy(hw, GG82563_PHY_INBAND_CTRL, data);
+ if (ret_val)
+ return ret_val;
+
+ return 0;
+}
+
+/**
+ * e1000_setup_copper_link_80003es2lan - Setup Copper Link for ESB2
+ * @hw: pointer to the HW structure
+ *
+ * Essentially a wrapper for setting up all things "copper" related.
+ * This is a function pointer entry point called by the mac module.
+ **/
+static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val;
+ u16 reg_data;
+
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_SLU;
+ ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ew32(CTRL, ctrl);
+
+ /*
+ * Set the mac to wait the maximum time between each
+ * iteration and increase the max iterations when
+ * polling the phy; this fixes erroneous timeouts at 10Mbps.
+ */
+ ret_val = e1000e_write_kmrn_reg(hw, GG82563_REG(0x34, 4), 0xFFFF);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000e_read_kmrn_reg(hw, GG82563_REG(0x34, 9), ®_data);
+ if (ret_val)
+ return ret_val;
+ reg_data |= 0x3F;
+ ret_val = e1000e_write_kmrn_reg(hw, GG82563_REG(0x34, 9), reg_data);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000e_read_kmrn_reg(hw,
+ E1000_KMRNCTRLSTA_OFFSET_INB_CTRL,
+ ®_data);
+ if (ret_val)
+ return ret_val;
+ reg_data |= E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING;
+ ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_OFFSET_INB_CTRL,
+ reg_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_copper_link_setup_gg82563_80003es2lan(hw);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000e_setup_copper_link(hw);
+
+ return 0;
+}
+
+/**
+ * e1000_cfg_kmrn_10_100_80003es2lan - Apply "quirks" for 10/100 operation
+ * @hw: pointer to the HW structure
+ * @duplex: current duplex setting
+ *
+ * Configure the KMRN interface by applying last minute quirks for
+ * 10/100 operation.
+ **/
+static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex)
+{
+ s32 ret_val;
+ u32 tipg;
+ u32 i = 0;
+ u16 reg_data, reg_data2;
+
+ reg_data = E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT;
+ ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
+ reg_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Configure Transmit Inter-Packet Gap */
+ tipg = er32(TIPG);
+ tipg &= ~E1000_TIPG_IPGT_MASK;
+ tipg |= DEFAULT_TIPG_IPGT_10_100_80003ES2LAN;
+ ew32(TIPG, tipg);
+
+ do {
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data2);
+ if (ret_val)
+ return ret_val;
+ i++;
+ } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY));
+
+ if (duplex == HALF_DUPLEX)
+ reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER;
+ else
+ reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+
+ ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
+
+ return 0;
+}
+
+/**
+ * e1000_cfg_kmrn_1000_80003es2lan - Apply "quirks" for gigabit operation
+ * @hw: pointer to the HW structure
+ *
+ * Configure the KMRN interface by applying last minute quirks for
+ * gigabit operation.
+ **/
+static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 reg_data, reg_data2;
+ u32 tipg;
+ u32 i = 0;
+
+ reg_data = E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT;
+ ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
+ reg_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Configure Transmit Inter-Packet Gap */
+ tipg = er32(TIPG);
+ tipg &= ~E1000_TIPG_IPGT_MASK;
+ tipg |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN;
+ ew32(TIPG, tipg);
+
+ do {
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data2);
+ if (ret_val)
+ return ret_val;
+ i++;
+ } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY));
+
+ reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+ ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
+
+ return ret_val;
+}
+
+/**
+ * e1000_clear_hw_cntrs_80003es2lan - Clear device specific hardware counters
+ * @hw: pointer to the HW structure
+ *
+ * Clears the hardware counters by reading the counter registers.
+ **/
+static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw)
+{
+ u32 temp;
+
+ e1000e_clear_hw_cntrs_base(hw);
+
+ temp = er32(PRC64);
+ temp = er32(PRC127);
+ temp = er32(PRC255);
+ temp = er32(PRC511);
+ temp = er32(PRC1023);
+ temp = er32(PRC1522);
+ temp = er32(PTC64);
+ temp = er32(PTC127);
+ temp = er32(PTC255);
+ temp = er32(PTC511);
+ temp = er32(PTC1023);
+ temp = er32(PTC1522);
+
+ temp = er32(ALGNERRC);
+ temp = er32(RXERRC);
+ temp = er32(TNCRS);
+ temp = er32(CEXTERR);
+ temp = er32(TSCTC);
+ temp = er32(TSCTFC);
+
+ temp = er32(MGTPRC);
+ temp = er32(MGTPDC);
+ temp = er32(MGTPTC);
+
+ temp = er32(IAC);
+ temp = er32(ICRXOC);
+
+ temp = er32(ICRXPTC);
+ temp = er32(ICRXATC);
+ temp = er32(ICTXPTC);
+ temp = er32(ICTXATC);
+ temp = er32(ICTXQEC);
+ temp = er32(ICTXQMTC);
+ temp = er32(ICRXDMTC);
+}
+
+static struct e1000_mac_operations es2_mac_ops = {
+ .check_mng_mode = e1000e_check_mng_mode_generic,
+ /* check_for_link dependent on media type */
+ .cleanup_led = e1000e_cleanup_led_generic,
+ .clear_hw_cntrs = e1000_clear_hw_cntrs_80003es2lan,
+ .get_bus_info = e1000e_get_bus_info_pcie,
+ .get_link_up_info = e1000_get_link_up_info_80003es2lan,
+ .led_on = e1000e_led_on_generic,
+ .led_off = e1000e_led_off_generic,
+ .update_mc_addr_list = e1000e_update_mc_addr_list_generic,
+ .reset_hw = e1000_reset_hw_80003es2lan,
+ .init_hw = e1000_init_hw_80003es2lan,
+ .setup_link = e1000e_setup_link,
+ /* setup_physical_interface dependent on media type */
+};
+
+static struct e1000_phy_operations es2_phy_ops = {
+ .acquire_phy = e1000_acquire_phy_80003es2lan,
+ .check_reset_block = e1000e_check_reset_block_generic,
+ .commit_phy = e1000e_phy_sw_reset,
+ .force_speed_duplex = e1000_phy_force_speed_duplex_80003es2lan,
+ .get_cfg_done = e1000_get_cfg_done_80003es2lan,
+ .get_cable_length = e1000_get_cable_length_80003es2lan,
+ .get_phy_info = e1000e_get_phy_info_m88,
+ .read_phy_reg = e1000_read_phy_reg_gg82563_80003es2lan,
+ .release_phy = e1000_release_phy_80003es2lan,
+ .reset_phy = e1000e_phy_hw_reset_generic,
+ .set_d0_lplu_state = NULL,
+ .set_d3_lplu_state = e1000e_set_d3_lplu_state,
+ .write_phy_reg = e1000_write_phy_reg_gg82563_80003es2lan,
+};
+
+static struct e1000_nvm_operations es2_nvm_ops = {
+ .acquire_nvm = e1000_acquire_nvm_80003es2lan,
+ .read_nvm = e1000e_read_nvm_eerd,
+ .release_nvm = e1000_release_nvm_80003es2lan,
+ .update_nvm = e1000e_update_nvm_checksum_generic,
+ .valid_led_default = e1000e_valid_led_default,
+ .validate_nvm = e1000e_validate_nvm_checksum_generic,
+ .write_nvm = e1000_write_nvm_80003es2lan,
+};
+
+struct e1000_info e1000_es2_info = {
+ .mac = e1000_80003es2lan,
+ .flags = FLAG_HAS_HW_VLAN_FILTER
+ | FLAG_HAS_JUMBO_FRAMES
+ | FLAG_HAS_WOL
+ | FLAG_APME_IN_CTRL3
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_CTRLEXT_ON_LOAD
+ | FLAG_RX_NEEDS_RESTART /* errata */
+ | FLAG_TARC_SET_BIT_ZERO /* errata */
+ | FLAG_APME_CHECK_PORT_B
+ | FLAG_DISABLE_FC_PAUSE_TIME /* errata */
+ | FLAG_TIPG_MEDIUM_FOR_80003ESLAN,
+ .pba = 38,
+ .get_variants = e1000_get_variants_80003es2lan,
+ .mac_ops = &es2_mac_ops,
+ .phy_ops = &es2_phy_ops,
+ .nvm_ops = &es2_nvm_ops,
+};
+
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2008 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+/* ethtool support for e1000 */
+
+#include <linux/netdevice.h>
+#include <linux/ethtool.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+
+#include "e1000.h"
+
+struct e1000_stats {
+ char stat_string[ETH_GSTRING_LEN];
+ int sizeof_stat;
+ int stat_offset;
+};
+
+#define E1000_STAT(m) sizeof(((struct e1000_adapter *)0)->m), \
+ offsetof(struct e1000_adapter, m)
+static const struct e1000_stats e1000_gstrings_stats[] = {
+ { "rx_packets", E1000_STAT(stats.gprc) },
+ { "tx_packets", E1000_STAT(stats.gptc) },
+ { "rx_bytes", E1000_STAT(stats.gorc) },
+ { "tx_bytes", E1000_STAT(stats.gotc) },
+ { "rx_broadcast", E1000_STAT(stats.bprc) },
+ { "tx_broadcast", E1000_STAT(stats.bptc) },
+ { "rx_multicast", E1000_STAT(stats.mprc) },
+ { "tx_multicast", E1000_STAT(stats.mptc) },
+ { "rx_errors", E1000_STAT(net_stats.rx_errors) },
+ { "tx_errors", E1000_STAT(net_stats.tx_errors) },
+ { "tx_dropped", E1000_STAT(net_stats.tx_dropped) },
+ { "multicast", E1000_STAT(stats.mprc) },
+ { "collisions", E1000_STAT(stats.colc) },
+ { "rx_length_errors", E1000_STAT(net_stats.rx_length_errors) },
+ { "rx_over_errors", E1000_STAT(net_stats.rx_over_errors) },
+ { "rx_crc_errors", E1000_STAT(stats.crcerrs) },
+ { "rx_frame_errors", E1000_STAT(net_stats.rx_frame_errors) },
+ { "rx_no_buffer_count", E1000_STAT(stats.rnbc) },
+ { "rx_missed_errors", E1000_STAT(stats.mpc) },
+ { "tx_aborted_errors", E1000_STAT(stats.ecol) },
+ { "tx_carrier_errors", E1000_STAT(stats.tncrs) },
+ { "tx_fifo_errors", E1000_STAT(net_stats.tx_fifo_errors) },
+ { "tx_heartbeat_errors", E1000_STAT(net_stats.tx_heartbeat_errors) },
+ { "tx_window_errors", E1000_STAT(stats.latecol) },
+ { "tx_abort_late_coll", E1000_STAT(stats.latecol) },
+ { "tx_deferred_ok", E1000_STAT(stats.dc) },
+ { "tx_single_coll_ok", E1000_STAT(stats.scc) },
+ { "tx_multi_coll_ok", E1000_STAT(stats.mcc) },
+ { "tx_timeout_count", E1000_STAT(tx_timeout_count) },
+ { "tx_restart_queue", E1000_STAT(restart_queue) },
+ { "rx_long_length_errors", E1000_STAT(stats.roc) },
+ { "rx_short_length_errors", E1000_STAT(stats.ruc) },
+ { "rx_align_errors", E1000_STAT(stats.algnerrc) },
+ { "tx_tcp_seg_good", E1000_STAT(stats.tsctc) },
+ { "tx_tcp_seg_failed", E1000_STAT(stats.tsctfc) },
+ { "rx_flow_control_xon", E1000_STAT(stats.xonrxc) },
+ { "rx_flow_control_xoff", E1000_STAT(stats.xoffrxc) },
+ { "tx_flow_control_xon", E1000_STAT(stats.xontxc) },
+ { "tx_flow_control_xoff", E1000_STAT(stats.xofftxc) },
+ { "rx_long_byte_count", E1000_STAT(stats.gorc) },
+ { "rx_csum_offload_good", E1000_STAT(hw_csum_good) },
+ { "rx_csum_offload_errors", E1000_STAT(hw_csum_err) },
+ { "rx_header_split", E1000_STAT(rx_hdr_split) },
+ { "alloc_rx_buff_failed", E1000_STAT(alloc_rx_buff_failed) },
+ { "tx_smbus", E1000_STAT(stats.mgptc) },
+ { "rx_smbus", E1000_STAT(stats.mgprc) },
+ { "dropped_smbus", E1000_STAT(stats.mgpdc) },
+ { "rx_dma_failed", E1000_STAT(rx_dma_failed) },
+ { "tx_dma_failed", E1000_STAT(tx_dma_failed) },
+};
+
+#define E1000_GLOBAL_STATS_LEN ARRAY_SIZE(e1000_gstrings_stats)
+#define E1000_STATS_LEN (E1000_GLOBAL_STATS_LEN)
+static const char e1000_gstrings_test[][ETH_GSTRING_LEN] = {
+ "Register test (offline)", "Eeprom test (offline)",
+ "Interrupt test (offline)", "Loopback test (offline)",
+ "Link test (on/offline)"
+};
+#define E1000_TEST_LEN ARRAY_SIZE(e1000_gstrings_test)
+
+static int e1000_get_settings(struct net_device *netdev,
+ struct ethtool_cmd *ecmd)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 status;
+
+ if (hw->phy.media_type == e1000_media_type_copper) {
+
+ ecmd->supported = (SUPPORTED_10baseT_Half |
+ SUPPORTED_10baseT_Full |
+ SUPPORTED_100baseT_Half |
+ SUPPORTED_100baseT_Full |
+ SUPPORTED_1000baseT_Full |
+ SUPPORTED_Autoneg |
+ SUPPORTED_TP);
+ if (hw->phy.type == e1000_phy_ife)
+ ecmd->supported &= ~SUPPORTED_1000baseT_Full;
+ ecmd->advertising = ADVERTISED_TP;
+
+ if (hw->mac.autoneg == 1) {
+ ecmd->advertising |= ADVERTISED_Autoneg;
+ /* the e1000 autoneg seems to match ethtool nicely */
+ ecmd->advertising |= hw->phy.autoneg_advertised;
+ }
+
+ ecmd->port = PORT_TP;
+ ecmd->phy_address = hw->phy.addr;
+ ecmd->transceiver = XCVR_INTERNAL;
+
+ } else {
+ ecmd->supported = (SUPPORTED_1000baseT_Full |
+ SUPPORTED_FIBRE |
+ SUPPORTED_Autoneg);
+
+ ecmd->advertising = (ADVERTISED_1000baseT_Full |
+ ADVERTISED_FIBRE |
+ ADVERTISED_Autoneg);
+
+ ecmd->port = PORT_FIBRE;
+ ecmd->transceiver = XCVR_EXTERNAL;
+ }
+
+ status = er32(STATUS);
+ if (status & E1000_STATUS_LU) {
+ if (status & E1000_STATUS_SPEED_1000)
+ ecmd->speed = 1000;
+ else if (status & E1000_STATUS_SPEED_100)
+ ecmd->speed = 100;
+ else
+ ecmd->speed = 10;
+
+ if (status & E1000_STATUS_FD)
+ ecmd->duplex = DUPLEX_FULL;
+ else
+ ecmd->duplex = DUPLEX_HALF;
+ } else {
+ ecmd->speed = -1;
+ ecmd->duplex = -1;
+ }
+
+ ecmd->autoneg = ((hw->phy.media_type == e1000_media_type_fiber) ||
+ hw->mac.autoneg) ? AUTONEG_ENABLE : AUTONEG_DISABLE;
+ return 0;
+}
+
+static u32 e1000_get_link(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 status;
+
+ status = er32(STATUS);
+ return (status & E1000_STATUS_LU) ? 1 : 0;
+}
+
+static int e1000_set_spd_dplx(struct e1000_adapter *adapter, u16 spddplx)
+{
+ struct e1000_mac_info *mac = &adapter->hw.mac;
+
+ mac->autoneg = 0;
+
+ /* Fiber NICs only allow 1000 gbps Full duplex */
+ if ((adapter->hw.phy.media_type == e1000_media_type_fiber) &&
+ spddplx != (SPEED_1000 + DUPLEX_FULL)) {
+ e_err("Unsupported Speed/Duplex configuration\n");
+ return -EINVAL;
+ }
+
+ switch (spddplx) {
+ case SPEED_10 + DUPLEX_HALF:
+ mac->forced_speed_duplex = ADVERTISE_10_HALF;
+ break;
+ case SPEED_10 + DUPLEX_FULL:
+ mac->forced_speed_duplex = ADVERTISE_10_FULL;
+ break;
+ case SPEED_100 + DUPLEX_HALF:
+ mac->forced_speed_duplex = ADVERTISE_100_HALF;
+ break;
+ case SPEED_100 + DUPLEX_FULL:
+ mac->forced_speed_duplex = ADVERTISE_100_FULL;
+ break;
+ case SPEED_1000 + DUPLEX_FULL:
+ mac->autoneg = 1;
+ adapter->hw.phy.autoneg_advertised = ADVERTISE_1000_FULL;
+ break;
+ case SPEED_1000 + DUPLEX_HALF: /* not supported */
+ default:
+ e_err("Unsupported Speed/Duplex configuration\n");
+ return -EINVAL;
+ }
+ return 0;
+}
+
+static int e1000_set_settings(struct net_device *netdev,
+ struct ethtool_cmd *ecmd)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ /*
+ * When SoL/IDER sessions are active, autoneg/speed/duplex
+ * cannot be changed
+ */
+ if (e1000_check_reset_block(hw)) {
+ e_err("Cannot change link characteristics when SoL/IDER is "
+ "active.\n");
+ return -EINVAL;
+ }
+
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
+ msleep(1);
+
+ if (ecmd->autoneg == AUTONEG_ENABLE) {
+ hw->mac.autoneg = 1;
+ if (hw->phy.media_type == e1000_media_type_fiber)
+ hw->phy.autoneg_advertised = ADVERTISED_1000baseT_Full |
+ ADVERTISED_FIBRE |
+ ADVERTISED_Autoneg;
+ else
+ hw->phy.autoneg_advertised = ecmd->advertising |
+ ADVERTISED_TP |
+ ADVERTISED_Autoneg;
+ ecmd->advertising = hw->phy.autoneg_advertised;
+ if (adapter->fc_autoneg)
+ hw->fc.original_type = e1000_fc_default;
+ } else {
+ if (e1000_set_spd_dplx(adapter, ecmd->speed + ecmd->duplex)) {
+ clear_bit(__E1000_RESETTING, &adapter->state);
+ return -EINVAL;
+ }
+ }
+
+ /* reset the link */
+
+ if (netif_running(adapter->netdev)) {
+ e1000e_down(adapter);
+ e1000e_up(adapter);
+ } else {
+ e1000e_reset(adapter);
+ }
+
+ clear_bit(__E1000_RESETTING, &adapter->state);
+ return 0;
+}
+
+static void e1000_get_pauseparam(struct net_device *netdev,
+ struct ethtool_pauseparam *pause)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ pause->autoneg =
+ (adapter->fc_autoneg ? AUTONEG_ENABLE : AUTONEG_DISABLE);
+
+ if (hw->fc.type == e1000_fc_rx_pause) {
+ pause->rx_pause = 1;
+ } else if (hw->fc.type == e1000_fc_tx_pause) {
+ pause->tx_pause = 1;
+ } else if (hw->fc.type == e1000_fc_full) {
+ pause->rx_pause = 1;
+ pause->tx_pause = 1;
+ }
+}
+
+static int e1000_set_pauseparam(struct net_device *netdev,
+ struct ethtool_pauseparam *pause)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ int retval = 0;
+
+ adapter->fc_autoneg = pause->autoneg;
+
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
+ msleep(1);
+
+ if (pause->rx_pause && pause->tx_pause)
+ hw->fc.type = e1000_fc_full;
+ else if (pause->rx_pause && !pause->tx_pause)
+ hw->fc.type = e1000_fc_rx_pause;
+ else if (!pause->rx_pause && pause->tx_pause)
+ hw->fc.type = e1000_fc_tx_pause;
+ else if (!pause->rx_pause && !pause->tx_pause)
+ hw->fc.type = e1000_fc_none;
+
+ hw->fc.original_type = hw->fc.type;
+
+ if (adapter->fc_autoneg == AUTONEG_ENABLE) {
+ hw->fc.type = e1000_fc_default;
+ if (netif_running(adapter->netdev)) {
+ e1000e_down(adapter);
+ e1000e_up(adapter);
+ } else {
+ e1000e_reset(adapter);
+ }
+ } else {
+ retval = ((hw->phy.media_type == e1000_media_type_fiber) ?
+ hw->mac.ops.setup_link(hw) : e1000e_force_mac_fc(hw));
+ }
+
+ clear_bit(__E1000_RESETTING, &adapter->state);
+ return retval;
+}
+
+static u32 e1000_get_rx_csum(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ return (adapter->flags & FLAG_RX_CSUM_ENABLED);
+}
+
+static int e1000_set_rx_csum(struct net_device *netdev, u32 data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ if (data)
+ adapter->flags |= FLAG_RX_CSUM_ENABLED;
+ else
+ adapter->flags &= ~FLAG_RX_CSUM_ENABLED;
+
+ if (netif_running(netdev))
+ e1000e_reinit_locked(adapter);
+ else
+ e1000e_reset(adapter);
+ return 0;
+}
+
+static u32 e1000_get_tx_csum(struct net_device *netdev)
+{
+ return ((netdev->features & NETIF_F_HW_CSUM) != 0);
+}
+
+static int e1000_set_tx_csum(struct net_device *netdev, u32 data)
+{
+ if (data)
+ netdev->features |= NETIF_F_HW_CSUM;
+ else
+ netdev->features &= ~NETIF_F_HW_CSUM;
+
+ return 0;
+}
+
+static int e1000_set_tso(struct net_device *netdev, u32 data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ if (data) {
+ netdev->features |= NETIF_F_TSO;
+ netdev->features |= NETIF_F_TSO6;
+ } else {
+ netdev->features &= ~NETIF_F_TSO;
+ netdev->features &= ~NETIF_F_TSO6;
+ }
+
+ e_info("TSO is %s\n", data ? "Enabled" : "Disabled");
+ adapter->flags |= FLAG_TSO_FORCE;
+ return 0;
+}
+
+static u32 e1000_get_msglevel(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ return adapter->msg_enable;
+}
+
+static void e1000_set_msglevel(struct net_device *netdev, u32 data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ adapter->msg_enable = data;
+}
+
+static int e1000_get_regs_len(struct net_device *netdev)
+{
+#define E1000_REGS_LEN 32 /* overestimate */
+ return E1000_REGS_LEN * sizeof(u32);
+}
+
+static void e1000_get_regs(struct net_device *netdev,
+ struct ethtool_regs *regs, void *p)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 *regs_buff = p;
+ u16 phy_data;
+ u8 revision_id;
+
+ memset(p, 0, E1000_REGS_LEN * sizeof(u32));
+
+ pci_read_config_byte(adapter->pdev, PCI_REVISION_ID, &revision_id);
+
+ regs->version = (1 << 24) | (revision_id << 16) | adapter->pdev->device;
+
+ regs_buff[0] = er32(CTRL);
+ regs_buff[1] = er32(STATUS);
+
+ regs_buff[2] = er32(RCTL);
+ regs_buff[3] = er32(RDLEN);
+ regs_buff[4] = er32(RDH);
+ regs_buff[5] = er32(RDT);
+ regs_buff[6] = er32(RDTR);
+
+ regs_buff[7] = er32(TCTL);
+ regs_buff[8] = er32(TDLEN);
+ regs_buff[9] = er32(TDH);
+ regs_buff[10] = er32(TDT);
+ regs_buff[11] = er32(TIDV);
+
+ regs_buff[12] = adapter->hw.phy.type; /* PHY type (IGP=1, M88=0) */
+ if (hw->phy.type == e1000_phy_m88) {
+ e1e_rphy(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+ regs_buff[13] = (u32)phy_data; /* cable length */
+ regs_buff[14] = 0; /* Dummy (to align w/ IGP phy reg dump) */
+ regs_buff[15] = 0; /* Dummy (to align w/ IGP phy reg dump) */
+ regs_buff[16] = 0; /* Dummy (to align w/ IGP phy reg dump) */
+ e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ regs_buff[17] = (u32)phy_data; /* extended 10bt distance */
+ regs_buff[18] = regs_buff[13]; /* cable polarity */
+ regs_buff[19] = 0; /* Dummy (to align w/ IGP phy reg dump) */
+ regs_buff[20] = regs_buff[17]; /* polarity correction */
+ /* phy receive errors */
+ regs_buff[22] = adapter->phy_stats.receive_errors;
+ regs_buff[23] = regs_buff[13]; /* mdix mode */
+ }
+ regs_buff[21] = adapter->phy_stats.idle_errors; /* phy idle errors */
+ e1e_rphy(hw, PHY_1000T_STATUS, &phy_data);
+ regs_buff[24] = (u32)phy_data; /* phy local receiver status */
+ regs_buff[25] = regs_buff[24]; /* phy remote receiver status */
+}
+
+static int e1000_get_eeprom_len(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ return adapter->hw.nvm.word_size * 2;
+}
+
+static int e1000_get_eeprom(struct net_device *netdev,
+ struct ethtool_eeprom *eeprom, u8 *bytes)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u16 *eeprom_buff;
+ int first_word;
+ int last_word;
+ int ret_val = 0;
+ u16 i;
+
+ if (eeprom->len == 0)
+ return -EINVAL;
+
+ eeprom->magic = adapter->pdev->vendor | (adapter->pdev->device << 16);
+
+ first_word = eeprom->offset >> 1;
+ last_word = (eeprom->offset + eeprom->len - 1) >> 1;
+
+ eeprom_buff = kmalloc(sizeof(u16) *
+ (last_word - first_word + 1), GFP_KERNEL);
+ if (!eeprom_buff)
+ return -ENOMEM;
+
+ if (hw->nvm.type == e1000_nvm_eeprom_spi) {
+ ret_val = e1000_read_nvm(hw, first_word,
+ last_word - first_word + 1,
+ eeprom_buff);
+ } else {
+ for (i = 0; i < last_word - first_word + 1; i++) {
+ ret_val = e1000_read_nvm(hw, first_word + i, 1,
+ &eeprom_buff[i]);
+ if (ret_val) {
+ /* a read error occurred, throw away the
+ * result */
+ memset(eeprom_buff, 0xff, sizeof(eeprom_buff));
+ break;
+ }
+ }
+ }
+
+ /* Device's eeprom is always little-endian, word addressable */
+ for (i = 0; i < last_word - first_word + 1; i++)
+ le16_to_cpus(&eeprom_buff[i]);
+
+ memcpy(bytes, (u8 *)eeprom_buff + (eeprom->offset & 1), eeprom->len);
+ kfree(eeprom_buff);
+
+ return ret_val;
+}
+
+static int e1000_set_eeprom(struct net_device *netdev,
+ struct ethtool_eeprom *eeprom, u8 *bytes)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u16 *eeprom_buff;
+ void *ptr;
+ int max_len;
+ int first_word;
+ int last_word;
+ int ret_val = 0;
+ u16 i;
+
+ if (eeprom->len == 0)
+ return -EOPNOTSUPP;
+
+ if (eeprom->magic != (adapter->pdev->vendor | (adapter->pdev->device << 16)))
+ return -EFAULT;
+
+ if (adapter->flags & FLAG_READ_ONLY_NVM)
+ return -EINVAL;
+
+ max_len = hw->nvm.word_size * 2;
+
+ first_word = eeprom->offset >> 1;
+ last_word = (eeprom->offset + eeprom->len - 1) >> 1;
+ eeprom_buff = kmalloc(max_len, GFP_KERNEL);
+ if (!eeprom_buff)
+ return -ENOMEM;
+
+ ptr = (void *)eeprom_buff;
+
+ if (eeprom->offset & 1) {
+ /* need read/modify/write of first changed EEPROM word */
+ /* only the second byte of the word is being modified */
+ ret_val = e1000_read_nvm(hw, first_word, 1, &eeprom_buff[0]);
+ ptr++;
+ }
+ if (((eeprom->offset + eeprom->len) & 1) && (ret_val == 0))
+ /* need read/modify/write of last changed EEPROM word */
+ /* only the first byte of the word is being modified */
+ ret_val = e1000_read_nvm(hw, last_word, 1,
+ &eeprom_buff[last_word - first_word]);
+
+ /* Device's eeprom is always little-endian, word addressable */
+ for (i = 0; i < last_word - first_word + 1; i++)
+ le16_to_cpus(&eeprom_buff[i]);
+
+ memcpy(ptr, bytes, eeprom->len);
+
+ for (i = 0; i < last_word - first_word + 1; i++)
+ eeprom_buff[i] = cpu_to_le16(eeprom_buff[i]);
+
+ ret_val = e1000_write_nvm(hw, first_word,
+ last_word - first_word + 1, eeprom_buff);
+
+ /*
+ * Update the checksum over the first part of the EEPROM if needed
+ * and flush shadow RAM for 82573 controllers
+ */
+ if ((ret_val == 0) && ((first_word <= NVM_CHECKSUM_REG) ||
+ (hw->mac.type == e1000_82574) ||
+ (hw->mac.type == e1000_82573)))
+ e1000e_update_nvm_checksum(hw);
+
+ kfree(eeprom_buff);
+ return ret_val;
+}
+
+static void e1000_get_drvinfo(struct net_device *netdev,
+ struct ethtool_drvinfo *drvinfo)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ char firmware_version[32];
+ u16 eeprom_data;
+
+ strncpy(drvinfo->driver, e1000e_driver_name, 32);
+ strncpy(drvinfo->version, e1000e_driver_version, 32);
+
+ /*
+ * EEPROM image version # is reported as firmware version # for
+ * PCI-E controllers
+ */
+ e1000_read_nvm(&adapter->hw, 5, 1, &eeprom_data);
+ sprintf(firmware_version, "%d.%d-%d",
+ (eeprom_data & 0xF000) >> 12,
+ (eeprom_data & 0x0FF0) >> 4,
+ eeprom_data & 0x000F);
+
+ strncpy(drvinfo->fw_version, firmware_version, 32);
+ strncpy(drvinfo->bus_info, pci_name(adapter->pdev), 32);
+ drvinfo->regdump_len = e1000_get_regs_len(netdev);
+ drvinfo->eedump_len = e1000_get_eeprom_len(netdev);
+}
+
+static void e1000_get_ringparam(struct net_device *netdev,
+ struct ethtool_ringparam *ring)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+
+ ring->rx_max_pending = E1000_MAX_RXD;
+ ring->tx_max_pending = E1000_MAX_TXD;
+ ring->rx_mini_max_pending = 0;
+ ring->rx_jumbo_max_pending = 0;
+ ring->rx_pending = rx_ring->count;
+ ring->tx_pending = tx_ring->count;
+ ring->rx_mini_pending = 0;
+ ring->rx_jumbo_pending = 0;
+}
+
+static int e1000_set_ringparam(struct net_device *netdev,
+ struct ethtool_ringparam *ring)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_ring *tx_ring, *tx_old;
+ struct e1000_ring *rx_ring, *rx_old;
+ int err;
+
+ if ((ring->rx_mini_pending) || (ring->rx_jumbo_pending))
+ return -EINVAL;
+
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
+ msleep(1);
+
+ if (netif_running(adapter->netdev))
+ e1000e_down(adapter);
+
+ tx_old = adapter->tx_ring;
+ rx_old = adapter->rx_ring;
+
+ err = -ENOMEM;
+ tx_ring = kzalloc(sizeof(struct e1000_ring), GFP_KERNEL);
+ if (!tx_ring)
+ goto err_alloc_tx;
+ /*
+ * use a memcpy to save any previously configured
+ * items like napi structs from having to be
+ * reinitialized
+ */
+ memcpy(tx_ring, tx_old, sizeof(struct e1000_ring));
+
+ rx_ring = kzalloc(sizeof(struct e1000_ring), GFP_KERNEL);
+ if (!rx_ring)
+ goto err_alloc_rx;
+ memcpy(rx_ring, rx_old, sizeof(struct e1000_ring));
+
+ adapter->tx_ring = tx_ring;
+ adapter->rx_ring = rx_ring;
+
+ rx_ring->count = max(ring->rx_pending, (u32)E1000_MIN_RXD);
+ rx_ring->count = min(rx_ring->count, (u32)(E1000_MAX_RXD));
+ rx_ring->count = ALIGN(rx_ring->count, REQ_RX_DESCRIPTOR_MULTIPLE);
+
+ tx_ring->count = max(ring->tx_pending, (u32)E1000_MIN_TXD);
+ tx_ring->count = min(tx_ring->count, (u32)(E1000_MAX_TXD));
+ tx_ring->count = ALIGN(tx_ring->count, REQ_TX_DESCRIPTOR_MULTIPLE);
+
+ if (netif_running(adapter->netdev)) {
+ /* Try to get new resources before deleting old */
+ err = e1000e_setup_rx_resources(adapter);
+ if (err)
+ goto err_setup_rx;
+ err = e1000e_setup_tx_resources(adapter);
+ if (err)
+ goto err_setup_tx;
+
+ /*
+ * restore the old in order to free it,
+ * then add in the new
+ */
+ adapter->rx_ring = rx_old;
+ adapter->tx_ring = tx_old;
+ e1000e_free_rx_resources(adapter);
+ e1000e_free_tx_resources(adapter);
+ kfree(tx_old);
+ kfree(rx_old);
+ adapter->rx_ring = rx_ring;
+ adapter->tx_ring = tx_ring;
+ err = e1000e_up(adapter);
+ if (err)
+ goto err_setup;
+ }
+
+ clear_bit(__E1000_RESETTING, &adapter->state);
+ return 0;
+err_setup_tx:
+ e1000e_free_rx_resources(adapter);
+err_setup_rx:
+ adapter->rx_ring = rx_old;
+ adapter->tx_ring = tx_old;
+ kfree(rx_ring);
+err_alloc_rx:
+ kfree(tx_ring);
+err_alloc_tx:
+ e1000e_up(adapter);
+err_setup:
+ clear_bit(__E1000_RESETTING, &adapter->state);
+ return err;
+}
+
+static int reg_pattern_test(struct e1000_adapter *adapter, u64 *data,
+ int reg, int offset, u32 mask, u32 write)
+{
+ u32 pat, val;
+ static const u32 test[] =
+ {0x5A5A5A5A, 0xA5A5A5A5, 0x00000000, 0xFFFFFFFF};
+ for (pat = 0; pat < ARRAY_SIZE(test); pat++) {
+ E1000_WRITE_REG_ARRAY(&adapter->hw, reg, offset,
+ (test[pat] & write));
+ val = E1000_READ_REG_ARRAY(&adapter->hw, reg, offset);
+ if (val != (test[pat] & write & mask)) {
+ e_err("pattern test reg %04X failed: got 0x%08X "
+ "expected 0x%08X\n", reg + offset, val,
+ (test[pat] & write & mask));
+ *data = reg;
+ return 1;
+ }
+ }
+ return 0;
+}
+
+static int reg_set_and_check(struct e1000_adapter *adapter, u64 *data,
+ int reg, u32 mask, u32 write)
+{
+ u32 val;
+ __ew32(&adapter->hw, reg, write & mask);
+ val = __er32(&adapter->hw, reg);
+ if ((write & mask) != (val & mask)) {
+ e_err("set/check reg %04X test failed: got 0x%08X "
+ "expected 0x%08X\n", reg, (val & mask), (write & mask));
+ *data = reg;
+ return 1;
+ }
+ return 0;
+}
+#define REG_PATTERN_TEST_ARRAY(reg, offset, mask, write) \
+ do { \
+ if (reg_pattern_test(adapter, data, reg, offset, mask, write)) \
+ return 1; \
+ } while (0)
+#define REG_PATTERN_TEST(reg, mask, write) \
+ REG_PATTERN_TEST_ARRAY(reg, 0, mask, write)
+
+#define REG_SET_AND_CHECK(reg, mask, write) \
+ do { \
+ if (reg_set_and_check(adapter, data, reg, mask, write)) \
+ return 1; \
+ } while (0)
+
+static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_mac_info *mac = &adapter->hw.mac;
+ u32 value;
+ u32 before;
+ u32 after;
+ u32 i;
+ u32 toggle;
+
+ /*
+ * The status register is Read Only, so a write should fail.
+ * Some bits that get toggled are ignored.
+ */
+ switch (mac->type) {
+ /* there are several bits on newer hardware that are r/w */
+ case e1000_82571:
+ case e1000_82572:
+ case e1000_80003es2lan:
+ toggle = 0x7FFFF3FF;
+ break;
+ case e1000_82573:
+ case e1000_82574:
+ case e1000_ich8lan:
+ case e1000_ich9lan:
+ case e1000_ich10lan:
+ toggle = 0x7FFFF033;
+ break;
+ default:
+ toggle = 0xFFFFF833;
+ break;
+ }
+
+ before = er32(STATUS);
+ value = (er32(STATUS) & toggle);
+ ew32(STATUS, toggle);
+ after = er32(STATUS) & toggle;
+ if (value != after) {
+ e_err("failed STATUS register test got: 0x%08X expected: "
+ "0x%08X\n", after, value);
+ *data = 1;
+ return 1;
+ }
+ /* restore previous status */
+ ew32(STATUS, before);
+
+ if (!(adapter->flags & FLAG_IS_ICH)) {
+ REG_PATTERN_TEST(E1000_FCAL, 0xFFFFFFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(E1000_FCAH, 0x0000FFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(E1000_FCT, 0x0000FFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(E1000_VET, 0x0000FFFF, 0xFFFFFFFF);
+ }
+
+ REG_PATTERN_TEST(E1000_RDTR, 0x0000FFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(E1000_RDBAH, 0xFFFFFFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(E1000_RDLEN, 0x000FFF80, 0x000FFFFF);
+ REG_PATTERN_TEST(E1000_RDH, 0x0000FFFF, 0x0000FFFF);
+ REG_PATTERN_TEST(E1000_RDT, 0x0000FFFF, 0x0000FFFF);
+ REG_PATTERN_TEST(E1000_FCRTH, 0x0000FFF8, 0x0000FFF8);
+ REG_PATTERN_TEST(E1000_FCTTV, 0x0000FFFF, 0x0000FFFF);
+ REG_PATTERN_TEST(E1000_TIPG, 0x3FFFFFFF, 0x3FFFFFFF);
+ REG_PATTERN_TEST(E1000_TDBAH, 0xFFFFFFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(E1000_TDLEN, 0x000FFF80, 0x000FFFFF);
+
+ REG_SET_AND_CHECK(E1000_RCTL, 0xFFFFFFFF, 0x00000000);
+
+ before = ((adapter->flags & FLAG_IS_ICH) ? 0x06C3B33E : 0x06DFB3FE);
+ REG_SET_AND_CHECK(E1000_RCTL, before, 0x003FFFFB);
+ REG_SET_AND_CHECK(E1000_TCTL, 0xFFFFFFFF, 0x00000000);
+
+ REG_SET_AND_CHECK(E1000_RCTL, before, 0xFFFFFFFF);
+ REG_PATTERN_TEST(E1000_RDBAL, 0xFFFFFFF0, 0xFFFFFFFF);
+ if (!(adapter->flags & FLAG_IS_ICH))
+ REG_PATTERN_TEST(E1000_TXCW, 0xC000FFFF, 0x0000FFFF);
+ REG_PATTERN_TEST(E1000_TDBAL, 0xFFFFFFF0, 0xFFFFFFFF);
+ REG_PATTERN_TEST(E1000_TIDV, 0x0000FFFF, 0x0000FFFF);
+ for (i = 0; i < mac->rar_entry_count; i++)
+ REG_PATTERN_TEST_ARRAY(E1000_RA, ((i << 1) + 1),
+ ((mac->type == e1000_ich10lan) ?
+ 0x8007FFFF : 0x8003FFFF),
+ 0xFFFFFFFF);
+
+ for (i = 0; i < mac->mta_reg_count; i++)
+ REG_PATTERN_TEST_ARRAY(E1000_MTA, i, 0xFFFFFFFF, 0xFFFFFFFF);
+
+ *data = 0;
+ return 0;
+}
+
+static int e1000_eeprom_test(struct e1000_adapter *adapter, u64 *data)
+{
+ u16 temp;
+ u16 checksum = 0;
+ u16 i;
+
+ *data = 0;
+ /* Read and add up the contents of the EEPROM */
+ for (i = 0; i < (NVM_CHECKSUM_REG + 1); i++) {
+ if ((e1000_read_nvm(&adapter->hw, i, 1, &temp)) < 0) {
+ *data = 1;
+ break;
+ }
+ checksum += temp;
+ }
+
+ /* If Checksum is not Correct return error else test passed */
+ if ((checksum != (u16) NVM_SUM) && !(*data))
+ *data = 2;
+
+ return *data;
+}
+
+static irqreturn_t e1000_test_intr(int irq, void *data, struct pt_regs *regs)
+{
+ struct net_device *netdev = (struct net_device *) data;
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ adapter->test_icr |= er32(ICR);
+
+ return IRQ_HANDLED;
+}
+
+static int e1000_intr_test(struct e1000_adapter *adapter, u64 *data)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct e1000_hw *hw = &adapter->hw;
+ u32 mask;
+ u32 shared_int = 1;
+ u32 irq = adapter->pdev->irq;
+ int i;
+ int ret_val = 0;
+ int int_mode = E1000E_INT_MODE_LEGACY;
+
+ *data = 0;
+
+ /* NOTE: we don't test MSI/MSI-X interrupts here, yet */
+ if (adapter->int_mode == E1000E_INT_MODE_MSIX) {
+ int_mode = adapter->int_mode;
+ e1000e_reset_interrupt_capability(adapter);
+ adapter->int_mode = E1000E_INT_MODE_LEGACY;
+ e1000e_set_interrupt_capability(adapter);
+ }
+ /* Hook up test interrupt handler just for this test */
+ if (!request_irq(irq, &e1000_test_intr, IRQF_PROBE_SHARED, netdev->name,
+ netdev)) {
+ shared_int = 0;
+ } else if (request_irq(irq, &e1000_test_intr, IRQF_SHARED,
+ netdev->name, netdev)) {
+ *data = 1;
+ ret_val = -1;
+ goto out;
+ }
+ e_info("testing %s interrupt\n", (shared_int ? "shared" : "unshared"));
+
+ /* Disable all the interrupts */
+ ew32(IMC, 0xFFFFFFFF);
+ msleep(10);
+
+ /* Test each interrupt */
+ for (i = 0; i < 10; i++) {
+ /* Interrupt to test */
+ mask = 1 << i;
+
+ if (adapter->flags & FLAG_IS_ICH) {
+ switch (mask) {
+ case E1000_ICR_RXSEQ:
+ continue;
+ case 0x00000100:
+ if (adapter->hw.mac.type == e1000_ich8lan ||
+ adapter->hw.mac.type == e1000_ich9lan)
+ continue;
+ break;
+ default:
+ break;
+ }
+ }
+
+ if (!shared_int) {
+ /*
+ * Disable the interrupt to be reported in
+ * the cause register and then force the same
+ * interrupt and see if one gets posted. If
+ * an interrupt was posted to the bus, the
+ * test failed.
+ */
+ adapter->test_icr = 0;
+ ew32(IMC, mask);
+ ew32(ICS, mask);
+ msleep(10);
+
+ if (adapter->test_icr & mask) {
+ *data = 3;
+ break;
+ }
+ }
+
+ /*
+ * Enable the interrupt to be reported in
+ * the cause register and then force the same
+ * interrupt and see if one gets posted. If
+ * an interrupt was not posted to the bus, the
+ * test failed.
+ */
+ adapter->test_icr = 0;
+ ew32(IMS, mask);
+ ew32(ICS, mask);
+ msleep(10);
+
+ if (!(adapter->test_icr & mask)) {
+ *data = 4;
+ break;
+ }
+
+ if (!shared_int) {
+ /*
+ * Disable the other interrupts to be reported in
+ * the cause register and then force the other
+ * interrupts and see if any get posted. If
+ * an interrupt was posted to the bus, the
+ * test failed.
+ */
+ adapter->test_icr = 0;
+ ew32(IMC, ~mask & 0x00007FFF);
+ ew32(ICS, ~mask & 0x00007FFF);
+ msleep(10);
+
+ if (adapter->test_icr) {
+ *data = 5;
+ break;
+ }
+ }
+ }
+
+ /* Disable all the interrupts */
+ ew32(IMC, 0xFFFFFFFF);
+ msleep(10);
+
+ /* Unhook test interrupt handler */
+ free_irq(irq, netdev);
+
+out:
+ if (int_mode == E1000E_INT_MODE_MSIX) {
+ e1000e_reset_interrupt_capability(adapter);
+ adapter->int_mode = int_mode;
+ e1000e_set_interrupt_capability(adapter);
+ }
+
+ return ret_val;
+}
+
+static void e1000_free_desc_rings(struct e1000_adapter *adapter)
+{
+ struct e1000_ring *tx_ring = &adapter->test_tx_ring;
+ struct e1000_ring *rx_ring = &adapter->test_rx_ring;
+ struct pci_dev *pdev = adapter->pdev;
+ int i;
+
+ if (tx_ring->desc && tx_ring->buffer_info) {
+ for (i = 0; i < tx_ring->count; i++) {
+ if (tx_ring->buffer_info[i].dma)
+ pci_unmap_single(pdev,
+ tx_ring->buffer_info[i].dma,
+ tx_ring->buffer_info[i].length,
+ PCI_DMA_TODEVICE);
+ if (tx_ring->buffer_info[i].skb)
+ dev_kfree_skb(tx_ring->buffer_info[i].skb);
+ }
+ }
+
+ if (rx_ring->desc && rx_ring->buffer_info) {
+ for (i = 0; i < rx_ring->count; i++) {
+ if (rx_ring->buffer_info[i].dma)
+ pci_unmap_single(pdev,
+ rx_ring->buffer_info[i].dma,
+ 2048, PCI_DMA_FROMDEVICE);
+ if (rx_ring->buffer_info[i].skb)
+ dev_kfree_skb(rx_ring->buffer_info[i].skb);
+ }
+ }
+
+ if (tx_ring->desc) {
+ dma_free_coherent(&pdev->dev, tx_ring->size, tx_ring->desc,
+ tx_ring->dma);
+ tx_ring->desc = NULL;
+ }
+ if (rx_ring->desc) {
+ dma_free_coherent(&pdev->dev, rx_ring->size, rx_ring->desc,
+ rx_ring->dma);
+ rx_ring->desc = NULL;
+ }
+
+ kfree(tx_ring->buffer_info);
+ tx_ring->buffer_info = NULL;
+ kfree(rx_ring->buffer_info);
+ rx_ring->buffer_info = NULL;
+}
+
+static int e1000_setup_desc_rings(struct e1000_adapter *adapter)
+{
+ struct e1000_ring *tx_ring = &adapter->test_tx_ring;
+ struct e1000_ring *rx_ring = &adapter->test_rx_ring;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_hw *hw = &adapter->hw;
+ u32 rctl;
+ int i;
+ int ret_val;
+
+ /* Setup Tx descriptor ring and Tx buffers */
+
+ if (!tx_ring->count)
+ tx_ring->count = E1000_DEFAULT_TXD;
+
+ tx_ring->buffer_info = kcalloc(tx_ring->count,
+ sizeof(struct e1000_buffer),
+ GFP_KERNEL);
+ if (!(tx_ring->buffer_info)) {
+ ret_val = 1;
+ goto err_nomem;
+ }
+
+ tx_ring->size = tx_ring->count * sizeof(struct e1000_tx_desc);
+ tx_ring->size = ALIGN(tx_ring->size, 4096);
+ tx_ring->desc = dma_alloc_coherent(&pdev->dev, tx_ring->size,
+ &tx_ring->dma, GFP_KERNEL);
+ if (!tx_ring->desc) {
+ ret_val = 2;
+ goto err_nomem;
+ }
+ tx_ring->next_to_use = 0;
+ tx_ring->next_to_clean = 0;
+
+ ew32(TDBAL, ((u64) tx_ring->dma & 0x00000000FFFFFFFF));
+ ew32(TDBAH, ((u64) tx_ring->dma >> 32));
+ ew32(TDLEN, tx_ring->count * sizeof(struct e1000_tx_desc));
+ ew32(TDH, 0);
+ ew32(TDT, 0);
+ ew32(TCTL, E1000_TCTL_PSP | E1000_TCTL_EN | E1000_TCTL_MULR |
+ E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT |
+ E1000_COLLISION_DISTANCE << E1000_COLD_SHIFT);
+
+ for (i = 0; i < tx_ring->count; i++) {
+ struct e1000_tx_desc *tx_desc = E1000_TX_DESC(*tx_ring, i);
+ struct sk_buff *skb;
+ unsigned int skb_size = 1024;
+
+ skb = alloc_skb(skb_size, GFP_KERNEL);
+ if (!skb) {
+ ret_val = 3;
+ goto err_nomem;
+ }
+ skb_put(skb, skb_size);
+ tx_ring->buffer_info[i].skb = skb;
+ tx_ring->buffer_info[i].length = skb->len;
+ tx_ring->buffer_info[i].dma =
+ pci_map_single(pdev, skb->data, skb->len,
+ PCI_DMA_TODEVICE);
+ if (pci_dma_mapping_error(tx_ring->buffer_info[i].dma)) {
+ ret_val = 4;
+ goto err_nomem;
+ }
+ tx_desc->buffer_addr = cpu_to_le64(tx_ring->buffer_info[i].dma);
+ tx_desc->lower.data = cpu_to_le32(skb->len);
+ tx_desc->lower.data |= cpu_to_le32(E1000_TXD_CMD_EOP |
+ E1000_TXD_CMD_IFCS |
+ E1000_TXD_CMD_RS);
+ tx_desc->upper.data = 0;
+ }
+
+ /* Setup Rx descriptor ring and Rx buffers */
+
+ if (!rx_ring->count)
+ rx_ring->count = E1000_DEFAULT_RXD;
+
+ rx_ring->buffer_info = kcalloc(rx_ring->count,
+ sizeof(struct e1000_buffer),
+ GFP_KERNEL);
+ if (!(rx_ring->buffer_info)) {
+ ret_val = 5;
+ goto err_nomem;
+ }
+
+ rx_ring->size = rx_ring->count * sizeof(struct e1000_rx_desc);
+ rx_ring->desc = dma_alloc_coherent(&pdev->dev, rx_ring->size,
+ &rx_ring->dma, GFP_KERNEL);
+ if (!rx_ring->desc) {
+ ret_val = 6;
+ goto err_nomem;
+ }
+ rx_ring->next_to_use = 0;
+ rx_ring->next_to_clean = 0;
+
+ rctl = er32(RCTL);
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
+ ew32(RDBAL, ((u64) rx_ring->dma & 0xFFFFFFFF));
+ ew32(RDBAH, ((u64) rx_ring->dma >> 32));
+ ew32(RDLEN, rx_ring->size);
+ ew32(RDH, 0);
+ ew32(RDT, 0);
+ rctl = E1000_RCTL_EN | E1000_RCTL_BAM | E1000_RCTL_SZ_2048 |
+ E1000_RCTL_UPE | E1000_RCTL_MPE | E1000_RCTL_LPE |
+ E1000_RCTL_SBP | E1000_RCTL_SECRC |
+ E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF |
+ (adapter->hw.mac.mc_filter_type << E1000_RCTL_MO_SHIFT);
+ ew32(RCTL, rctl);
+
+ for (i = 0; i < rx_ring->count; i++) {
+ struct e1000_rx_desc *rx_desc = E1000_RX_DESC(*rx_ring, i);
+ struct sk_buff *skb;
+
+ skb = alloc_skb(2048 + NET_IP_ALIGN, GFP_KERNEL);
+ if (!skb) {
+ ret_val = 7;
+ goto err_nomem;
+ }
+ skb_reserve(skb, NET_IP_ALIGN);
+ rx_ring->buffer_info[i].skb = skb;
+ rx_ring->buffer_info[i].dma =
+ pci_map_single(pdev, skb->data, 2048,
+ PCI_DMA_FROMDEVICE);
+ if (pci_dma_mapping_error(rx_ring->buffer_info[i].dma)) {
+ ret_val = 8;
+ goto err_nomem;
+ }
+ rx_desc->buffer_addr =
+ cpu_to_le64(rx_ring->buffer_info[i].dma);
+ memset(skb->data, 0x00, skb->len);
+ }
+
+ return 0;
+
+err_nomem:
+ e1000_free_desc_rings(adapter);
+ return ret_val;
+}
+
+static void e1000_phy_disable_receiver(struct e1000_adapter *adapter)
+{
+ /* Write out to PHY registers 29 and 30 to disable the Receiver. */
+ e1e_wphy(&adapter->hw, 29, 0x001F);
+ e1e_wphy(&adapter->hw, 30, 0x8FFC);
+ e1e_wphy(&adapter->hw, 29, 0x001A);
+ e1e_wphy(&adapter->hw, 30, 0x8FF0);
+}
+
+static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl_reg = 0;
+ u32 stat_reg = 0;
+ u16 phy_reg = 0;
+
+ hw->mac.autoneg = 0;
+
+ if (hw->phy.type == e1000_phy_m88) {
+ /* Auto-MDI/MDIX Off */
+ e1e_wphy(hw, M88E1000_PHY_SPEC_CTRL, 0x0808);
+ /* reset to update Auto-MDI/MDIX */
+ e1e_wphy(hw, PHY_CONTROL, 0x9140);
+ /* autoneg off */
+ e1e_wphy(hw, PHY_CONTROL, 0x8140);
+ } else if (hw->phy.type == e1000_phy_gg82563)
+ e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, 0x1CC);
+
+ ctrl_reg = er32(CTRL);
+
+ switch (hw->phy.type) {
+ case e1000_phy_ife:
+ /* force 100, set loopback */
+ e1e_wphy(hw, PHY_CONTROL, 0x6100);
+
+ /* Now set up the MAC to the same speed/duplex as the PHY. */
+ ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */
+ ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
+ E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
+ E1000_CTRL_SPD_100 |/* Force Speed to 100 */
+ E1000_CTRL_FD); /* Force Duplex to FULL */
+ break;
+ case e1000_phy_bm:
+ /* Set Default MAC Interface speed to 1GB */
+ e1e_rphy(hw, PHY_REG(2, 21), &phy_reg);
+ phy_reg &= ~0x0007;
+ phy_reg |= 0x006;
+ e1e_wphy(hw, PHY_REG(2, 21), phy_reg);
+ /* Assert SW reset for above settings to take effect */
+ e1000e_commit_phy(hw);
+ mdelay(1);
+ /* Force Full Duplex */
+ e1e_rphy(hw, PHY_REG(769, 16), &phy_reg);
+ e1e_wphy(hw, PHY_REG(769, 16), phy_reg | 0x000C);
+ /* Set Link Up (in force link) */
+ e1e_rphy(hw, PHY_REG(776, 16), &phy_reg);
+ e1e_wphy(hw, PHY_REG(776, 16), phy_reg | 0x0040);
+ /* Force Link */
+ e1e_rphy(hw, PHY_REG(769, 16), &phy_reg);
+ e1e_wphy(hw, PHY_REG(769, 16), phy_reg | 0x0040);
+ /* Set Early Link Enable */
+ e1e_rphy(hw, PHY_REG(769, 20), &phy_reg);
+ e1e_wphy(hw, PHY_REG(769, 20), phy_reg | 0x0400);
+ /* fall through */
+ default:
+ /* force 1000, set loopback */
+ e1e_wphy(hw, PHY_CONTROL, 0x4140);
+ mdelay(250);
+
+ /* Now set up the MAC to the same speed/duplex as the PHY. */
+ ctrl_reg = er32(CTRL);
+ ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */
+ ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
+ E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
+ E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */
+ E1000_CTRL_FD); /* Force Duplex to FULL */
+
+ if (adapter->flags & FLAG_IS_ICH)
+ ctrl_reg |= E1000_CTRL_SLU; /* Set Link Up */
+ }
+
+ if (hw->phy.media_type == e1000_media_type_copper &&
+ hw->phy.type == e1000_phy_m88) {
+ ctrl_reg |= E1000_CTRL_ILOS; /* Invert Loss of Signal */
+ } else {
+ /*
+ * Set the ILOS bit on the fiber Nic if half duplex link is
+ * detected.
+ */
+ stat_reg = er32(STATUS);
+ if ((stat_reg & E1000_STATUS_FD) == 0)
+ ctrl_reg |= (E1000_CTRL_ILOS | E1000_CTRL_SLU);
+ }
+
+ ew32(CTRL, ctrl_reg);
+
+ /*
+ * Disable the receiver on the PHY so when a cable is plugged in, the
+ * PHY does not begin to autoneg when a cable is reconnected to the NIC.
+ */
+ if (hw->phy.type == e1000_phy_m88)
+ e1000_phy_disable_receiver(adapter);
+
+ udelay(500);
+
+ return 0;
+}
+
+static int e1000_set_82571_fiber_loopback(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl = er32(CTRL);
+ int link = 0;
+
+ /* special requirements for 82571/82572 fiber adapters */
+
+ /*
+ * jump through hoops to make sure link is up because serdes
+ * link is hardwired up
+ */
+ ctrl |= E1000_CTRL_SLU;
+ ew32(CTRL, ctrl);
+
+ /* disable autoneg */
+ ctrl = er32(TXCW);
+ ctrl &= ~(1 << 31);
+ ew32(TXCW, ctrl);
+
+ link = (er32(STATUS) & E1000_STATUS_LU);
+
+ if (!link) {
+ /* set invert loss of signal */
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_ILOS;
+ ew32(CTRL, ctrl);
+ }
+
+ /*
+ * special write to serdes control register to enable SerDes analog
+ * loopback
+ */
+#define E1000_SERDES_LB_ON 0x410
+ ew32(SCTL, E1000_SERDES_LB_ON);
+ msleep(10);
+
+ return 0;
+}
+
+/* only call this for fiber/serdes connections to es2lan */
+static int e1000_set_es2lan_mac_loopback(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrlext = er32(CTRL_EXT);
+ u32 ctrl = er32(CTRL);
+
+ /*
+ * save CTRL_EXT to restore later, reuse an empty variable (unused
+ * on mac_type 80003es2lan)
+ */
+ adapter->tx_fifo_head = ctrlext;
+
+ /* clear the serdes mode bits, putting the device into mac loopback */
+ ctrlext &= ~E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES;
+ ew32(CTRL_EXT, ctrlext);
+
+ /* force speed to 1000/FD, link up */
+ ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
+ ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX |
+ E1000_CTRL_SPD_1000 | E1000_CTRL_FD);
+ ew32(CTRL, ctrl);
+
+ /* set mac loopback */
+ ctrl = er32(RCTL);
+ ctrl |= E1000_RCTL_LBM_MAC;
+ ew32(RCTL, ctrl);
+
+ /* set testing mode parameters (no need to reset later) */
+#define KMRNCTRLSTA_OPMODE (0x1F << 16)
+#define KMRNCTRLSTA_OPMODE_1GB_FD_GMII 0x0582
+ ew32(KMRNCTRLSTA,
+ (KMRNCTRLSTA_OPMODE | KMRNCTRLSTA_OPMODE_1GB_FD_GMII));
+
+ return 0;
+}
+
+static int e1000_setup_loopback_test(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 rctl;
+
+ if (hw->phy.media_type == e1000_media_type_fiber ||
+ hw->phy.media_type == e1000_media_type_internal_serdes) {
+ switch (hw->mac.type) {
+ case e1000_80003es2lan:
+ return e1000_set_es2lan_mac_loopback(adapter);
+ break;
+ case e1000_82571:
+ case e1000_82572:
+ return e1000_set_82571_fiber_loopback(adapter);
+ break;
+ default:
+ rctl = er32(RCTL);
+ rctl |= E1000_RCTL_LBM_TCVR;
+ ew32(RCTL, rctl);
+ return 0;
+ }
+ } else if (hw->phy.media_type == e1000_media_type_copper) {
+ return e1000_integrated_phy_loopback(adapter);
+ }
+
+ return 7;
+}
+
+static void e1000_loopback_cleanup(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 rctl;
+ u16 phy_reg;
+
+ rctl = er32(RCTL);
+ rctl &= ~(E1000_RCTL_LBM_TCVR | E1000_RCTL_LBM_MAC);
+ ew32(RCTL, rctl);
+
+ switch (hw->mac.type) {
+ case e1000_80003es2lan:
+ if (hw->phy.media_type == e1000_media_type_fiber ||
+ hw->phy.media_type == e1000_media_type_internal_serdes) {
+ /* restore CTRL_EXT, stealing space from tx_fifo_head */
+ ew32(CTRL_EXT, adapter->tx_fifo_head);
+ adapter->tx_fifo_head = 0;
+ }
+ /* fall through */
+ case e1000_82571:
+ case e1000_82572:
+ if (hw->phy.media_type == e1000_media_type_fiber ||
+ hw->phy.media_type == e1000_media_type_internal_serdes) {
+#define E1000_SERDES_LB_OFF 0x400
+ ew32(SCTL, E1000_SERDES_LB_OFF);
+ msleep(10);
+ break;
+ }
+ /* Fall Through */
+ default:
+ hw->mac.autoneg = 1;
+ if (hw->phy.type == e1000_phy_gg82563)
+ e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, 0x180);
+ e1e_rphy(hw, PHY_CONTROL, &phy_reg);
+ if (phy_reg & MII_CR_LOOPBACK) {
+ phy_reg &= ~MII_CR_LOOPBACK;
+ e1e_wphy(hw, PHY_CONTROL, phy_reg);
+ e1000e_commit_phy(hw);
+ }
+ break;
+ }
+}
+
+static void e1000_create_lbtest_frame(struct sk_buff *skb,
+ unsigned int frame_size)
+{
+ memset(skb->data, 0xFF, frame_size);
+ frame_size &= ~1;
+ memset(&skb->data[frame_size / 2], 0xAA, frame_size / 2 - 1);
+ memset(&skb->data[frame_size / 2 + 10], 0xBE, 1);
+ memset(&skb->data[frame_size / 2 + 12], 0xAF, 1);
+}
+
+static int e1000_check_lbtest_frame(struct sk_buff *skb,
+ unsigned int frame_size)
+{
+ frame_size &= ~1;
+ if (*(skb->data + 3) == 0xFF)
+ if ((*(skb->data + frame_size / 2 + 10) == 0xBE) &&
+ (*(skb->data + frame_size / 2 + 12) == 0xAF))
+ return 0;
+ return 13;
+}
+
+static int e1000_run_loopback_test(struct e1000_adapter *adapter)
+{
+ struct e1000_ring *tx_ring = &adapter->test_tx_ring;
+ struct e1000_ring *rx_ring = &adapter->test_rx_ring;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_hw *hw = &adapter->hw;
+ int i, j, k, l;
+ int lc;
+ int good_cnt;
+ int ret_val = 0;
+ unsigned long time;
+
+ ew32(RDT, rx_ring->count - 1);
+
+ /*
+ * Calculate the loop count based on the largest descriptor ring
+ * The idea is to wrap the largest ring a number of times using 64
+ * send/receive pairs during each loop
+ */
+
+ if (rx_ring->count <= tx_ring->count)
+ lc = ((tx_ring->count / 64) * 2) + 1;
+ else
+ lc = ((rx_ring->count / 64) * 2) + 1;
+
+ k = 0;
+ l = 0;
+ for (j = 0; j <= lc; j++) { /* loop count loop */
+ for (i = 0; i < 64; i++) { /* send the packets */
+ e1000_create_lbtest_frame(tx_ring->buffer_info[k].skb,
+ 1024);
+ pci_dma_sync_single_for_device(pdev,
+ tx_ring->buffer_info[k].dma,
+ tx_ring->buffer_info[k].length,
+ PCI_DMA_TODEVICE);
+ k++;
+ if (k == tx_ring->count)
+ k = 0;
+ }
+ ew32(TDT, k);
+ msleep(200);
+ time = jiffies; /* set the start time for the receive */
+ good_cnt = 0;
+ do { /* receive the sent packets */
+ pci_dma_sync_single_for_cpu(pdev,
+ rx_ring->buffer_info[l].dma, 2048,
+ PCI_DMA_FROMDEVICE);
+
+ ret_val = e1000_check_lbtest_frame(
+ rx_ring->buffer_info[l].skb, 1024);
+ if (!ret_val)
+ good_cnt++;
+ l++;
+ if (l == rx_ring->count)
+ l = 0;
+ /*
+ * time + 20 msecs (200 msecs on 2.4) is more than
+ * enough time to complete the receives, if it's
+ * exceeded, break and error off
+ */
+ } while (good_cnt < 64 && jiffies < (time + 20));
+ if (good_cnt != 64) {
+ ret_val = 13; /* ret_val is the same as mis-compare */
+ break;
+ }
+ if (jiffies >= (time + 20)) {
+ ret_val = 14; /* error code for time out error */
+ break;
+ }
+ } /* end loop count loop */
+ return ret_val;
+}
+
+static int e1000_loopback_test(struct e1000_adapter *adapter, u64 *data)
+{
+ /*
+ * PHY loopback cannot be performed if SoL/IDER
+ * sessions are active
+ */
+ if (e1000_check_reset_block(&adapter->hw)) {
+ e_err("Cannot do PHY loopback test when SoL/IDER is active.\n");
+ *data = 0;
+ goto out;
+ }
+
+ *data = e1000_setup_desc_rings(adapter);
+ if (*data)
+ goto out;
+
+ *data = e1000_setup_loopback_test(adapter);
+ if (*data)
+ goto err_loopback;
+
+ *data = e1000_run_loopback_test(adapter);
+ e1000_loopback_cleanup(adapter);
+
+err_loopback:
+ e1000_free_desc_rings(adapter);
+out:
+ return *data;
+}
+
+static int e1000_link_test(struct e1000_adapter *adapter, u64 *data)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ *data = 0;
+ if (hw->phy.media_type == e1000_media_type_internal_serdes) {
+ int i = 0;
+ hw->mac.serdes_has_link = 0;
+
+ /*
+ * On some blade server designs, link establishment
+ * could take as long as 2-3 minutes
+ */
+ do {
+ hw->mac.ops.check_for_link(hw);
+ if (hw->mac.serdes_has_link)
+ return *data;
+ msleep(20);
+ } while (i++ < 3750);
+
+ *data = 1;
+ } else {
+ hw->mac.ops.check_for_link(hw);
+ if (hw->mac.autoneg)
+ msleep(4000);
+
+ if (!(er32(STATUS) &
+ E1000_STATUS_LU))
+ *data = 1;
+ }
+ return *data;
+}
+
+static int e1000_diag_test_count(struct net_device *netdev)
+{
+ return E1000_TEST_LEN;
+}
+
+static void e1000_diag_test(struct net_device *netdev,
+ struct ethtool_test *eth_test, u64 *data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ u16 autoneg_advertised;
+ u8 forced_speed_duplex;
+ u8 autoneg;
+ int if_running = netif_running(netdev);
+
+ set_bit(__E1000_TESTING, &adapter->state);
+ if (eth_test->flags == ETH_TEST_FL_OFFLINE) {
+ /* Offline tests */
+
+ /* save speed, duplex, autoneg settings */
+ autoneg_advertised = adapter->hw.phy.autoneg_advertised;
+ forced_speed_duplex = adapter->hw.mac.forced_speed_duplex;
+ autoneg = adapter->hw.mac.autoneg;
+
+ e_info("offline testing starting\n");
+
+ /*
+ * Link test performed before hardware reset so autoneg doesn't
+ * interfere with test result
+ */
+ if (e1000_link_test(adapter, &data[4]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ if (if_running)
+ /* indicate we're in test mode */
+ dev_close(netdev);
+ else
+ e1000e_reset(adapter);
+
+ if (e1000_reg_test(adapter, &data[0]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ e1000e_reset(adapter);
+ if (e1000_eeprom_test(adapter, &data[1]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ e1000e_reset(adapter);
+ if (e1000_intr_test(adapter, &data[2]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ e1000e_reset(adapter);
+ /* make sure the phy is powered up */
+ e1000e_power_up_phy(adapter);
+ if (e1000_loopback_test(adapter, &data[3]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ /* restore speed, duplex, autoneg settings */
+ adapter->hw.phy.autoneg_advertised = autoneg_advertised;
+ adapter->hw.mac.forced_speed_duplex = forced_speed_duplex;
+ adapter->hw.mac.autoneg = autoneg;
+
+ /* force this routine to wait until autoneg complete/timeout */
+ adapter->hw.phy.autoneg_wait_to_complete = 1;
+ e1000e_reset(adapter);
+ adapter->hw.phy.autoneg_wait_to_complete = 0;
+
+ clear_bit(__E1000_TESTING, &adapter->state);
+ if (if_running)
+ dev_open(netdev);
+ } else {
+ e_info("online testing starting\n");
+ /* Online tests */
+ if (e1000_link_test(adapter, &data[4]))
+ eth_test->flags |= ETH_TEST_FL_FAILED;
+
+ /* Online tests aren't run; pass by default */
+ data[0] = 0;
+ data[1] = 0;
+ data[2] = 0;
+ data[3] = 0;
+
+ clear_bit(__E1000_TESTING, &adapter->state);
+ }
+ msleep_interruptible(4 * 1000);
+}
+
+static void e1000_get_wol(struct net_device *netdev,
+ struct ethtool_wolinfo *wol)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ wol->supported = 0;
+ wol->wolopts = 0;
+
+ if (!(adapter->flags & FLAG_HAS_WOL))
+ return;
+
+ wol->supported = WAKE_UCAST | WAKE_MCAST |
+ WAKE_BCAST | WAKE_MAGIC |
+ WAKE_PHY | WAKE_ARP;
+
+ /* apply any specific unsupported masks here */
+ if (adapter->flags & FLAG_NO_WAKE_UCAST) {
+ wol->supported &= ~WAKE_UCAST;
+
+ if (adapter->wol & E1000_WUFC_EX)
+ e_err("Interface does not support directed (unicast) "
+ "frame wake-up packets\n");
+ }
+
+ if (adapter->wol & E1000_WUFC_EX)
+ wol->wolopts |= WAKE_UCAST;
+ if (adapter->wol & E1000_WUFC_MC)
+ wol->wolopts |= WAKE_MCAST;
+ if (adapter->wol & E1000_WUFC_BC)
+ wol->wolopts |= WAKE_BCAST;
+ if (adapter->wol & E1000_WUFC_MAG)
+ wol->wolopts |= WAKE_MAGIC;
+ if (adapter->wol & E1000_WUFC_LNKC)
+ wol->wolopts |= WAKE_PHY;
+ if (adapter->wol & E1000_WUFC_ARP)
+ wol->wolopts |= WAKE_ARP;
+ if (adapter->wol & E1000_WUFC_LNKC)
+ wol->wolopts |= WAKE_PHY;
+ if (adapter->wol & E1000_WUFC_ARP)
+ wol->wolopts |= WAKE_ARP;
+}
+
+static int e1000_set_wol(struct net_device *netdev,
+ struct ethtool_wolinfo *wol)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ if (wol->wolopts & WAKE_MAGICSECURE)
+ return -EOPNOTSUPP;
+
+ if (!(adapter->flags & FLAG_HAS_WOL))
+ return wol->wolopts ? -EOPNOTSUPP : 0;
+
+ /* these settings will always override what we currently have */
+ adapter->wol = 0;
+
+ if (wol->wolopts & WAKE_UCAST)
+ adapter->wol |= E1000_WUFC_EX;
+ if (wol->wolopts & WAKE_MCAST)
+ adapter->wol |= E1000_WUFC_MC;
+ if (wol->wolopts & WAKE_BCAST)
+ adapter->wol |= E1000_WUFC_BC;
+ if (wol->wolopts & WAKE_MAGIC)
+ adapter->wol |= E1000_WUFC_MAG;
+ if (wol->wolopts & WAKE_PHY)
+ adapter->wol |= E1000_WUFC_LNKC;
+ if (wol->wolopts & WAKE_ARP)
+ adapter->wol |= E1000_WUFC_ARP;
+
+ return 0;
+}
+
+/* toggle LED 4 times per second = 2 "blinks" per second */
+#define E1000_ID_INTERVAL (HZ/4)
+
+/* bit defines for adapter->led_status */
+#define E1000_LED_ON 0
+
+static void e1000_led_blink_callback(unsigned long data)
+{
+ struct e1000_adapter *adapter = (struct e1000_adapter *) data;
+
+ if (test_and_change_bit(E1000_LED_ON, &adapter->led_status))
+ adapter->hw.mac.ops.led_off(&adapter->hw);
+ else
+ adapter->hw.mac.ops.led_on(&adapter->hw);
+
+ mod_timer(&adapter->blink_timer, jiffies + E1000_ID_INTERVAL);
+}
+
+static int e1000_phys_id(struct net_device *netdev, u32 data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (!data)
+ data = INT_MAX;
+
+ if ((hw->phy.type == e1000_phy_ife) ||
+ (hw->mac.type == e1000_82574)) {
+ if (!adapter->blink_timer.function) {
+ init_timer(&adapter->blink_timer);
+ adapter->blink_timer.function =
+ e1000_led_blink_callback;
+ adapter->blink_timer.data = (unsigned long) adapter;
+ }
+ mod_timer(&adapter->blink_timer, jiffies);
+ msleep_interruptible(data * 1000);
+ del_timer_sync(&adapter->blink_timer);
+ if (hw->phy.type == e1000_phy_ife)
+ e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED, 0);
+ } else {
+ e1000e_blink_led(hw);
+ msleep_interruptible(data * 1000);
+ }
+
+ hw->mac.ops.led_off(hw);
+ clear_bit(E1000_LED_ON, &adapter->led_status);
+ hw->mac.ops.cleanup_led(hw);
+
+ return 0;
+}
+
+static int e1000_get_coalesce(struct net_device *netdev,
+ struct ethtool_coalesce *ec)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ if (adapter->itr_setting <= 3)
+ ec->rx_coalesce_usecs = adapter->itr_setting;
+ else
+ ec->rx_coalesce_usecs = 1000000 / adapter->itr_setting;
+
+ return 0;
+}
+
+static int e1000_set_coalesce(struct net_device *netdev,
+ struct ethtool_coalesce *ec)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ if ((ec->rx_coalesce_usecs > E1000_MAX_ITR_USECS) ||
+ ((ec->rx_coalesce_usecs > 3) &&
+ (ec->rx_coalesce_usecs < E1000_MIN_ITR_USECS)) ||
+ (ec->rx_coalesce_usecs == 2))
+ return -EINVAL;
+
+ if (ec->rx_coalesce_usecs <= 3) {
+ adapter->itr = 20000;
+ adapter->itr_setting = ec->rx_coalesce_usecs;
+ } else {
+ adapter->itr = (1000000 / ec->rx_coalesce_usecs);
+ adapter->itr_setting = adapter->itr & ~3;
+ }
+
+ if (adapter->itr_setting != 0)
+ ew32(ITR, 1000000000 / (adapter->itr * 256));
+ else
+ ew32(ITR, 0);
+
+ return 0;
+}
+
+static int e1000_nway_reset(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ if (netif_running(netdev))
+ e1000e_reinit_locked(adapter);
+ return 0;
+}
+
+static int e1000_get_stats_count(struct net_device *netdev)
+{
+ return E1000_STATS_LEN;
+}
+
+static void e1000_get_ethtool_stats(struct net_device *netdev,
+ struct ethtool_stats *stats,
+ u64 *data)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ int i;
+
+ e1000e_update_stats(adapter);
+ for (i = 0; i < E1000_GLOBAL_STATS_LEN; i++) {
+ char *p = (char *)adapter+e1000_gstrings_stats[i].stat_offset;
+ data[i] = (e1000_gstrings_stats[i].sizeof_stat ==
+ sizeof(u64)) ? *(u64 *)p : *(u32 *)p;
+ }
+}
+
+static void e1000_get_strings(struct net_device *netdev, u32 stringset,
+ u8 *data)
+{
+ u8 *p = data;
+ int i;
+
+ switch (stringset) {
+ case ETH_SS_TEST:
+ memcpy(data, *e1000_gstrings_test, E1000_TEST_LEN*ETH_GSTRING_LEN);
+ break;
+ case ETH_SS_STATS:
+ for (i = 0; i < E1000_GLOBAL_STATS_LEN; i++) {
+ memcpy(p, e1000_gstrings_stats[i].stat_string,
+ ETH_GSTRING_LEN);
+ p += ETH_GSTRING_LEN;
+ }
+ break;
+ }
+}
+
+static struct ethtool_ops e1000_ethtool_ops = {
+ .get_settings = e1000_get_settings,
+ .set_settings = e1000_set_settings,
+ .get_drvinfo = e1000_get_drvinfo,
+ .get_regs_len = e1000_get_regs_len,
+ .get_regs = e1000_get_regs,
+ .get_wol = e1000_get_wol,
+ .set_wol = e1000_set_wol,
+ .get_msglevel = e1000_get_msglevel,
+ .set_msglevel = e1000_set_msglevel,
+ .nway_reset = e1000_nway_reset,
+ .get_link = e1000_get_link,
+ .get_eeprom_len = e1000_get_eeprom_len,
+ .get_eeprom = e1000_get_eeprom,
+ .set_eeprom = e1000_set_eeprom,
+ .get_ringparam = e1000_get_ringparam,
+ .set_ringparam = e1000_set_ringparam,
+ .get_pauseparam = e1000_get_pauseparam,
+ .set_pauseparam = e1000_set_pauseparam,
+ .get_rx_csum = e1000_get_rx_csum,
+ .set_rx_csum = e1000_set_rx_csum,
+ .get_tx_csum = e1000_get_tx_csum,
+ .set_tx_csum = e1000_set_tx_csum,
+ .get_sg = ethtool_op_get_sg,
+ .set_sg = ethtool_op_set_sg,
+ .get_tso = ethtool_op_get_tso,
+ .set_tso = e1000_set_tso,
+ .self_test_count = e1000_diag_test_count,
+ .self_test = e1000_diag_test,
+ .get_strings = e1000_get_strings,
+ .phys_id = e1000_phys_id,
+ .get_stats_count = e1000_get_stats_count,
+ .get_ethtool_stats = e1000_get_ethtool_stats,
+ .get_coalesce = e1000_get_coalesce,
+ .set_coalesce = e1000_set_coalesce,
+};
+
+void e1000e_set_ethtool_ops(struct net_device *netdev)
+{
+ SET_ETHTOOL_OPS(netdev, &e1000_ethtool_ops);
+}
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2008 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#ifndef _E1000_HW_H_
+#define _E1000_HW_H_
+
+#include <linux/types.h>
+
+struct e1000_hw;
+struct e1000_adapter;
+
+#include "defines.h"
+
+#define er32(reg) __er32(hw, E1000_##reg)
+#define ew32(reg,val) __ew32(hw, E1000_##reg, (val))
+#define e1e_flush() er32(STATUS)
+
+#define E1000_WRITE_REG_ARRAY(a, reg, offset, value) \
+ (writel((value), ((a)->hw_addr + reg + ((offset) << 2))))
+
+#define E1000_READ_REG_ARRAY(a, reg, offset) \
+ (readl((a)->hw_addr + reg + ((offset) << 2)))
+
+enum e1e_registers {
+ E1000_CTRL = 0x00000, /* Device Control - RW */
+ E1000_STATUS = 0x00008, /* Device Status - RO */
+ E1000_EECD = 0x00010, /* EEPROM/Flash Control - RW */
+ E1000_EERD = 0x00014, /* EEPROM Read - RW */
+ E1000_CTRL_EXT = 0x00018, /* Extended Device Control - RW */
+ E1000_FLA = 0x0001C, /* Flash Access - RW */
+ E1000_MDIC = 0x00020, /* MDI Control - RW */
+ E1000_SCTL = 0x00024, /* SerDes Control - RW */
+ E1000_FCAL = 0x00028, /* Flow Control Address Low - RW */
+ E1000_FCAH = 0x0002C, /* Flow Control Address High -RW */
+ E1000_FEXTNVM = 0x00028, /* Future Extended NVM - RW */
+ E1000_FCT = 0x00030, /* Flow Control Type - RW */
+ E1000_VET = 0x00038, /* VLAN Ether Type - RW */
+ E1000_ICR = 0x000C0, /* Interrupt Cause Read - R/clr */
+ E1000_ITR = 0x000C4, /* Interrupt Throttling Rate - RW */
+ E1000_ICS = 0x000C8, /* Interrupt Cause Set - WO */
+ E1000_IMS = 0x000D0, /* Interrupt Mask Set - RW */
+ E1000_IMC = 0x000D8, /* Interrupt Mask Clear - WO */
+ E1000_EIAC_82574 = 0x000DC, /* Ext. Interrupt Auto Clear - RW */
+ E1000_IAM = 0x000E0, /* Interrupt Acknowledge Auto Mask */
+ E1000_IVAR = 0x000E4, /* Interrupt Vector Allocation - RW */
+ E1000_EITR_82574_BASE = 0x000E8, /* Interrupt Throttling - RW */
+#define E1000_EITR_82574(_n) (E1000_EITR_82574_BASE + (_n << 2))
+ E1000_RCTL = 0x00100, /* Rx Control - RW */
+ E1000_FCTTV = 0x00170, /* Flow Control Transmit Timer Value - RW */
+ E1000_TXCW = 0x00178, /* Tx Configuration Word - RW */
+ E1000_RXCW = 0x00180, /* Rx Configuration Word - RO */
+ E1000_TCTL = 0x00400, /* Tx Control - RW */
+ E1000_TCTL_EXT = 0x00404, /* Extended Tx Control - RW */
+ E1000_TIPG = 0x00410, /* Tx Inter-packet gap -RW */
+ E1000_AIT = 0x00458, /* Adaptive Interframe Spacing Throttle -RW */
+ E1000_LEDCTL = 0x00E00, /* LED Control - RW */
+ E1000_EXTCNF_CTRL = 0x00F00, /* Extended Configuration Control */
+ E1000_EXTCNF_SIZE = 0x00F08, /* Extended Configuration Size */
+ E1000_PHY_CTRL = 0x00F10, /* PHY Control Register in CSR */
+ E1000_PBA = 0x01000, /* Packet Buffer Allocation - RW */
+ E1000_PBS = 0x01008, /* Packet Buffer Size */
+ E1000_EEMNGCTL = 0x01010, /* MNG EEprom Control */
+ E1000_EEWR = 0x0102C, /* EEPROM Write Register - RW */
+ E1000_FLOP = 0x0103C, /* FLASH Opcode Register */
+ E1000_PBA_ECC = 0x01100, /* PBA ECC Register */
+ E1000_ERT = 0x02008, /* Early Rx Threshold - RW */
+ E1000_FCRTL = 0x02160, /* Flow Control Receive Threshold Low - RW */
+ E1000_FCRTH = 0x02168, /* Flow Control Receive Threshold High - RW */
+ E1000_PSRCTL = 0x02170, /* Packet Split Receive Control - RW */
+ E1000_RDBAL = 0x02800, /* Rx Descriptor Base Address Low - RW */
+ E1000_RDBAH = 0x02804, /* Rx Descriptor Base Address High - RW */
+ E1000_RDLEN = 0x02808, /* Rx Descriptor Length - RW */
+ E1000_RDH = 0x02810, /* Rx Descriptor Head - RW */
+ E1000_RDT = 0x02818, /* Rx Descriptor Tail - RW */
+ E1000_RDTR = 0x02820, /* Rx Delay Timer - RW */
+ E1000_RXDCTL_BASE = 0x02828, /* Rx Descriptor Control - RW */
+#define E1000_RXDCTL(_n) (E1000_RXDCTL_BASE + (_n << 8))
+ E1000_RADV = 0x0282C, /* RX Interrupt Absolute Delay Timer - RW */
+
+/* Convenience macros
+ *
+ * Note: "_n" is the queue number of the register to be written to.
+ *
+ * Example usage:
+ * E1000_RDBAL_REG(current_rx_queue)
+ *
+ */
+#define E1000_RDBAL_REG(_n) (E1000_RDBAL + (_n << 8))
+ E1000_KABGTXD = 0x03004, /* AFE Band Gap Transmit Ref Data */
+ E1000_TDBAL = 0x03800, /* Tx Descriptor Base Address Low - RW */
+ E1000_TDBAH = 0x03804, /* Tx Descriptor Base Address High - RW */
+ E1000_TDLEN = 0x03808, /* Tx Descriptor Length - RW */
+ E1000_TDH = 0x03810, /* Tx Descriptor Head - RW */
+ E1000_TDT = 0x03818, /* Tx Descriptor Tail - RW */
+ E1000_TIDV = 0x03820, /* Tx Interrupt Delay Value - RW */
+ E1000_TXDCTL_BASE = 0x03828, /* Tx Descriptor Control - RW */
+#define E1000_TXDCTL(_n) (E1000_TXDCTL_BASE + (_n << 8))
+ E1000_TADV = 0x0382C, /* Tx Interrupt Absolute Delay Val - RW */
+ E1000_TARC_BASE = 0x03840, /* Tx Arbitration Count (0) */
+#define E1000_TARC(_n) (E1000_TARC_BASE + (_n << 8))
+ E1000_CRCERRS = 0x04000, /* CRC Error Count - R/clr */
+ E1000_ALGNERRC = 0x04004, /* Alignment Error Count - R/clr */
+ E1000_SYMERRS = 0x04008, /* Symbol Error Count - R/clr */
+ E1000_RXERRC = 0x0400C, /* Receive Error Count - R/clr */
+ E1000_MPC = 0x04010, /* Missed Packet Count - R/clr */
+ E1000_SCC = 0x04014, /* Single Collision Count - R/clr */
+ E1000_ECOL = 0x04018, /* Excessive Collision Count - R/clr */
+ E1000_MCC = 0x0401C, /* Multiple Collision Count - R/clr */
+ E1000_LATECOL = 0x04020, /* Late Collision Count - R/clr */
+ E1000_COLC = 0x04028, /* Collision Count - R/clr */
+ E1000_DC = 0x04030, /* Defer Count - R/clr */
+ E1000_TNCRS = 0x04034, /* Tx-No CRS - R/clr */
+ E1000_SEC = 0x04038, /* Sequence Error Count - R/clr */
+ E1000_CEXTERR = 0x0403C, /* Carrier Extension Error Count - R/clr */
+ E1000_RLEC = 0x04040, /* Receive Length Error Count - R/clr */
+ E1000_XONRXC = 0x04048, /* XON Rx Count - R/clr */
+ E1000_XONTXC = 0x0404C, /* XON Tx Count - R/clr */
+ E1000_XOFFRXC = 0x04050, /* XOFF Rx Count - R/clr */
+ E1000_XOFFTXC = 0x04054, /* XOFF Tx Count - R/clr */
+ E1000_FCRUC = 0x04058, /* Flow Control Rx Unsupported Count- R/clr */
+ E1000_PRC64 = 0x0405C, /* Packets Rx (64 bytes) - R/clr */
+ E1000_PRC127 = 0x04060, /* Packets Rx (65-127 bytes) - R/clr */
+ E1000_PRC255 = 0x04064, /* Packets Rx (128-255 bytes) - R/clr */
+ E1000_PRC511 = 0x04068, /* Packets Rx (255-511 bytes) - R/clr */
+ E1000_PRC1023 = 0x0406C, /* Packets Rx (512-1023 bytes) - R/clr */
+ E1000_PRC1522 = 0x04070, /* Packets Rx (1024-1522 bytes) - R/clr */
+ E1000_GPRC = 0x04074, /* Good Packets Rx Count - R/clr */
+ E1000_BPRC = 0x04078, /* Broadcast Packets Rx Count - R/clr */
+ E1000_MPRC = 0x0407C, /* Multicast Packets Rx Count - R/clr */
+ E1000_GPTC = 0x04080, /* Good Packets Tx Count - R/clr */
+ E1000_GORCL = 0x04088, /* Good Octets Rx Count Low - R/clr */
+ E1000_GORCH = 0x0408C, /* Good Octets Rx Count High - R/clr */
+ E1000_GOTCL = 0x04090, /* Good Octets Tx Count Low - R/clr */
+ E1000_GOTCH = 0x04094, /* Good Octets Tx Count High - R/clr */
+ E1000_RNBC = 0x040A0, /* Rx No Buffers Count - R/clr */
+ E1000_RUC = 0x040A4, /* Rx Undersize Count - R/clr */
+ E1000_RFC = 0x040A8, /* Rx Fragment Count - R/clr */
+ E1000_ROC = 0x040AC, /* Rx Oversize Count - R/clr */
+ E1000_RJC = 0x040B0, /* Rx Jabber Count - R/clr */
+ E1000_MGTPRC = 0x040B4, /* Management Packets Rx Count - R/clr */
+ E1000_MGTPDC = 0x040B8, /* Management Packets Dropped Count - R/clr */
+ E1000_MGTPTC = 0x040BC, /* Management Packets Tx Count - R/clr */
+ E1000_TORL = 0x040C0, /* Total Octets Rx Low - R/clr */
+ E1000_TORH = 0x040C4, /* Total Octets Rx High - R/clr */
+ E1000_TOTL = 0x040C8, /* Total Octets Tx Low - R/clr */
+ E1000_TOTH = 0x040CC, /* Total Octets Tx High - R/clr */
+ E1000_TPR = 0x040D0, /* Total Packets Rx - R/clr */
+ E1000_TPT = 0x040D4, /* Total Packets Tx - R/clr */
+ E1000_PTC64 = 0x040D8, /* Packets Tx (64 bytes) - R/clr */
+ E1000_PTC127 = 0x040DC, /* Packets Tx (65-127 bytes) - R/clr */
+ E1000_PTC255 = 0x040E0, /* Packets Tx (128-255 bytes) - R/clr */
+ E1000_PTC511 = 0x040E4, /* Packets Tx (256-511 bytes) - R/clr */
+ E1000_PTC1023 = 0x040E8, /* Packets Tx (512-1023 bytes) - R/clr */
+ E1000_PTC1522 = 0x040EC, /* Packets Tx (1024-1522 Bytes) - R/clr */
+ E1000_MPTC = 0x040F0, /* Multicast Packets Tx Count - R/clr */
+ E1000_BPTC = 0x040F4, /* Broadcast Packets Tx Count - R/clr */
+ E1000_TSCTC = 0x040F8, /* TCP Segmentation Context Tx - R/clr */
+ E1000_TSCTFC = 0x040FC, /* TCP Segmentation Context Tx Fail - R/clr */
+ E1000_IAC = 0x04100, /* Interrupt Assertion Count */
+ E1000_ICRXPTC = 0x04104, /* Irq Cause Rx Packet Timer Expire Count */
+ E1000_ICRXATC = 0x04108, /* Irq Cause Rx Abs Timer Expire Count */
+ E1000_ICTXPTC = 0x0410C, /* Irq Cause Tx Packet Timer Expire Count */
+ E1000_ICTXATC = 0x04110, /* Irq Cause Tx Abs Timer Expire Count */
+ E1000_ICTXQEC = 0x04118, /* Irq Cause Tx Queue Empty Count */
+ E1000_ICTXQMTC = 0x0411C, /* Irq Cause Tx Queue MinThreshold Count */
+ E1000_ICRXDMTC = 0x04120, /* Irq Cause Rx Desc MinThreshold Count */
+ E1000_ICRXOC = 0x04124, /* Irq Cause Receiver Overrun Count */
+ E1000_RXCSUM = 0x05000, /* Rx Checksum Control - RW */
+ E1000_RFCTL = 0x05008, /* Receive Filter Control */
+ E1000_MTA = 0x05200, /* Multicast Table Array - RW Array */
+ E1000_RA = 0x05400, /* Receive Address - RW Array */
+ E1000_VFTA = 0x05600, /* VLAN Filter Table Array - RW Array */
+ E1000_WUC = 0x05800, /* Wakeup Control - RW */
+ E1000_WUFC = 0x05808, /* Wakeup Filter Control - RW */
+ E1000_WUS = 0x05810, /* Wakeup Status - RO */
+ E1000_MANC = 0x05820, /* Management Control - RW */
+ E1000_FFLT = 0x05F00, /* Flexible Filter Length Table - RW Array */
+ E1000_HOST_IF = 0x08800, /* Host Interface */
+
+ E1000_KMRNCTRLSTA = 0x00034, /* MAC-PHY interface - RW */
+ E1000_MANC2H = 0x05860, /* Management Control To Host - RW */
+ E1000_SW_FW_SYNC = 0x05B5C, /* Software-Firmware Synchronization - RW */
+ E1000_GCR = 0x05B00, /* PCI-Ex Control */
+ E1000_FACTPS = 0x05B30, /* Function Active and Power State to MNG */
+ E1000_SWSM = 0x05B50, /* SW Semaphore */
+ E1000_FWSM = 0x05B54, /* FW Semaphore */
+ E1000_HICR = 0x08F00, /* Host Interface Control */
+};
+
+/* RSS registers */
+
+/* IGP01E1000 Specific Registers */
+#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* Port Config */
+#define IGP01E1000_PHY_PORT_STATUS 0x11 /* Status */
+#define IGP01E1000_PHY_PORT_CTRL 0x12 /* Control */
+#define IGP01E1000_PHY_LINK_HEALTH 0x13 /* PHY Link Health */
+#define IGP02E1000_PHY_POWER_MGMT 0x19 /* Power Management */
+#define IGP01E1000_PHY_PAGE_SELECT 0x1F /* Page Select */
+#define BM_PHY_PAGE_SELECT 22 /* Page Select for BM */
+#define IGP_PAGE_SHIFT 5
+#define PHY_REG_MASK 0x1F
+
+#define BM_WUC_PAGE 800
+#define BM_WUC_ADDRESS_OPCODE 0x11
+#define BM_WUC_DATA_OPCODE 0x12
+#define BM_WUC_ENABLE_PAGE 769
+#define BM_WUC_ENABLE_REG 17
+#define BM_WUC_ENABLE_BIT (1 << 2)
+#define BM_WUC_HOST_WU_BIT (1 << 4)
+
+#define BM_WUC PHY_REG(BM_WUC_PAGE, 1)
+#define BM_WUFC PHY_REG(BM_WUC_PAGE, 2)
+#define BM_WUS PHY_REG(BM_WUC_PAGE, 3)
+
+#define IGP01E1000_PHY_PCS_INIT_REG 0x00B4
+#define IGP01E1000_PHY_POLARITY_MASK 0x0078
+
+#define IGP01E1000_PSCR_AUTO_MDIX 0x1000
+#define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0=MDI, 1=MDIX */
+
+#define IGP01E1000_PSCFR_SMART_SPEED 0x0080
+
+#define IGP02E1000_PM_SPD 0x0001 /* Smart Power Down */
+#define IGP02E1000_PM_D0_LPLU 0x0002 /* For D0a states */
+#define IGP02E1000_PM_D3_LPLU 0x0004 /* For all other states */
+
+#define IGP01E1000_PLHR_SS_DOWNGRADE 0x8000
+
+#define IGP01E1000_PSSR_POLARITY_REVERSED 0x0002
+#define IGP01E1000_PSSR_MDIX 0x0008
+#define IGP01E1000_PSSR_SPEED_MASK 0xC000
+#define IGP01E1000_PSSR_SPEED_1000MBPS 0xC000
+
+#define IGP02E1000_PHY_CHANNEL_NUM 4
+#define IGP02E1000_PHY_AGC_A 0x11B1
+#define IGP02E1000_PHY_AGC_B 0x12B1
+#define IGP02E1000_PHY_AGC_C 0x14B1
+#define IGP02E1000_PHY_AGC_D 0x18B1
+
+#define IGP02E1000_AGC_LENGTH_SHIFT 9 /* Course - 15:13, Fine - 12:9 */
+#define IGP02E1000_AGC_LENGTH_MASK 0x7F
+#define IGP02E1000_AGC_RANGE 15
+
+/* manage.c */
+#define E1000_VFTA_ENTRY_SHIFT 5
+#define E1000_VFTA_ENTRY_MASK 0x7F
+#define E1000_VFTA_ENTRY_BIT_SHIFT_MASK 0x1F
+
+#define E1000_HICR_EN 0x01 /* Enable bit - RO */
+/* Driver sets this bit when done to put command in RAM */
+#define E1000_HICR_C 0x02
+#define E1000_HICR_FW_RESET_ENABLE 0x40
+#define E1000_HICR_FW_RESET 0x80
+
+#define E1000_FWSM_MODE_MASK 0xE
+#define E1000_FWSM_MODE_SHIFT 1
+
+#define E1000_MNG_IAMT_MODE 0x3
+#define E1000_MNG_DHCP_COOKIE_LENGTH 0x10
+#define E1000_MNG_DHCP_COOKIE_OFFSET 0x6F0
+#define E1000_MNG_DHCP_COMMAND_TIMEOUT 10
+#define E1000_MNG_DHCP_TX_PAYLOAD_CMD 64
+#define E1000_MNG_DHCP_COOKIE_STATUS_PARSING 0x1
+#define E1000_MNG_DHCP_COOKIE_STATUS_VLAN 0x2
+
+/* nvm.c */
+#define E1000_STM_OPCODE 0xDB00
+
+#define E1000_KMRNCTRLSTA_OFFSET 0x001F0000
+#define E1000_KMRNCTRLSTA_OFFSET_SHIFT 16
+#define E1000_KMRNCTRLSTA_REN 0x00200000
+#define E1000_KMRNCTRLSTA_DIAG_OFFSET 0x3 /* Kumeran Diagnostic */
+#define E1000_KMRNCTRLSTA_DIAG_NELPBK 0x1000 /* Nearend Loopback mode */
+
+#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10
+#define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY Special Control */
+#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY Special and LED Control */
+#define IFE_PHY_MDIX_CONTROL 0x1C /* MDI/MDI-X Control */
+
+/* IFE PHY Extended Status Control */
+#define IFE_PESC_POLARITY_REVERSED 0x0100
+
+/* IFE PHY Special Control */
+#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010
+#define IFE_PSC_FORCE_POLARITY 0x0020
+
+/* IFE PHY Special Control and LED Control */
+#define IFE_PSCL_PROBE_MODE 0x0020
+#define IFE_PSCL_PROBE_LEDS_OFF 0x0006 /* Force LEDs 0 and 2 off */
+#define IFE_PSCL_PROBE_LEDS_ON 0x0007 /* Force LEDs 0 and 2 on */
+
+/* IFE PHY MDIX Control */
+#define IFE_PMC_MDIX_STATUS 0x0020 /* 1=MDI-X, 0=MDI */
+#define IFE_PMC_FORCE_MDIX 0x0040 /* 1=force MDI-X, 0=force MDI */
+#define IFE_PMC_AUTO_MDIX 0x0080 /* 1=enable auto MDI/MDI-X, 0=disable */
+
+#define E1000_CABLE_LENGTH_UNDEFINED 0xFF
+
+#define E1000_DEV_ID_82571EB_COPPER 0x105E
+#define E1000_DEV_ID_82571EB_FIBER 0x105F
+#define E1000_DEV_ID_82571EB_SERDES 0x1060
+#define E1000_DEV_ID_82571EB_QUAD_COPPER 0x10A4
+#define E1000_DEV_ID_82571PT_QUAD_COPPER 0x10D5
+#define E1000_DEV_ID_82571EB_QUAD_FIBER 0x10A5
+#define E1000_DEV_ID_82571EB_QUAD_COPPER_LP 0x10BC
+#define E1000_DEV_ID_82571EB_SERDES_DUAL 0x10D9
+#define E1000_DEV_ID_82571EB_SERDES_QUAD 0x10DA
+#define E1000_DEV_ID_82572EI_COPPER 0x107D
+#define E1000_DEV_ID_82572EI_FIBER 0x107E
+#define E1000_DEV_ID_82572EI_SERDES 0x107F
+#define E1000_DEV_ID_82572EI 0x10B9
+#define E1000_DEV_ID_82573E 0x108B
+#define E1000_DEV_ID_82573E_IAMT 0x108C
+#define E1000_DEV_ID_82573L 0x109A
+#define E1000_DEV_ID_82574L 0x10D3
+
+#define E1000_DEV_ID_80003ES2LAN_COPPER_DPT 0x1096
+#define E1000_DEV_ID_80003ES2LAN_SERDES_DPT 0x1098
+#define E1000_DEV_ID_80003ES2LAN_COPPER_SPT 0x10BA
+#define E1000_DEV_ID_80003ES2LAN_SERDES_SPT 0x10BB
+
+#define E1000_DEV_ID_ICH8_IGP_M_AMT 0x1049
+#define E1000_DEV_ID_ICH8_IGP_AMT 0x104A
+#define E1000_DEV_ID_ICH8_IGP_C 0x104B
+#define E1000_DEV_ID_ICH8_IFE 0x104C
+#define E1000_DEV_ID_ICH8_IFE_GT 0x10C4
+#define E1000_DEV_ID_ICH8_IFE_G 0x10C5
+#define E1000_DEV_ID_ICH8_IGP_M 0x104D
+#define E1000_DEV_ID_ICH9_IGP_AMT 0x10BD
+#define E1000_DEV_ID_ICH9_BM 0x10E5
+#define E1000_DEV_ID_ICH9_IGP_M_AMT 0x10F5
+#define E1000_DEV_ID_ICH9_IGP_M 0x10BF
+#define E1000_DEV_ID_ICH9_IGP_M_V 0x10CB
+#define E1000_DEV_ID_ICH9_IGP_C 0x294C
+#define E1000_DEV_ID_ICH9_IFE 0x10C0
+#define E1000_DEV_ID_ICH9_IFE_GT 0x10C3
+#define E1000_DEV_ID_ICH9_IFE_G 0x10C2
+#define E1000_DEV_ID_ICH10_R_BM_LM 0x10CC
+#define E1000_DEV_ID_ICH10_R_BM_LF 0x10CD
+#define E1000_DEV_ID_ICH10_R_BM_V 0x10CE
+#define E1000_DEV_ID_ICH10_D_BM_LM 0x10DE
+#define E1000_DEV_ID_ICH10_D_BM_LF 0x10DF
+
+#define E1000_REVISION_4 4
+
+#define E1000_FUNC_1 1
+
+enum e1000_mac_type {
+ e1000_82571,
+ e1000_82572,
+ e1000_82573,
+ e1000_82574,
+ e1000_80003es2lan,
+ e1000_ich8lan,
+ e1000_ich9lan,
+ e1000_ich10lan,
+};
+
+enum e1000_media_type {
+ e1000_media_type_unknown = 0,
+ e1000_media_type_copper = 1,
+ e1000_media_type_fiber = 2,
+ e1000_media_type_internal_serdes = 3,
+ e1000_num_media_types
+};
+
+enum e1000_nvm_type {
+ e1000_nvm_unknown = 0,
+ e1000_nvm_none,
+ e1000_nvm_eeprom_spi,
+ e1000_nvm_flash_hw,
+ e1000_nvm_flash_sw
+};
+
+enum e1000_nvm_override {
+ e1000_nvm_override_none = 0,
+ e1000_nvm_override_spi_small,
+ e1000_nvm_override_spi_large
+};
+
+enum e1000_phy_type {
+ e1000_phy_unknown = 0,
+ e1000_phy_none,
+ e1000_phy_m88,
+ e1000_phy_igp,
+ e1000_phy_igp_2,
+ e1000_phy_gg82563,
+ e1000_phy_igp_3,
+ e1000_phy_ife,
+ e1000_phy_bm,
+};
+
+enum e1000_bus_width {
+ e1000_bus_width_unknown = 0,
+ e1000_bus_width_pcie_x1,
+ e1000_bus_width_pcie_x2,
+ e1000_bus_width_pcie_x4 = 4,
+ e1000_bus_width_32,
+ e1000_bus_width_64,
+ e1000_bus_width_reserved
+};
+
+enum e1000_1000t_rx_status {
+ e1000_1000t_rx_status_not_ok = 0,
+ e1000_1000t_rx_status_ok,
+ e1000_1000t_rx_status_undefined = 0xFF
+};
+
+enum e1000_rev_polarity{
+ e1000_rev_polarity_normal = 0,
+ e1000_rev_polarity_reversed,
+ e1000_rev_polarity_undefined = 0xFF
+};
+
+enum e1000_fc_type {
+ e1000_fc_none = 0,
+ e1000_fc_rx_pause,
+ e1000_fc_tx_pause,
+ e1000_fc_full,
+ e1000_fc_default = 0xFF
+};
+
+enum e1000_ms_type {
+ e1000_ms_hw_default = 0,
+ e1000_ms_force_master,
+ e1000_ms_force_slave,
+ e1000_ms_auto
+};
+
+enum e1000_smart_speed {
+ e1000_smart_speed_default = 0,
+ e1000_smart_speed_on,
+ e1000_smart_speed_off
+};
+
+/* Receive Descriptor */
+struct e1000_rx_desc {
+ __le64 buffer_addr; /* Address of the descriptor's data buffer */
+ __le16 length; /* Length of data DMAed into data buffer */
+ __le16 csum; /* Packet checksum */
+ u8 status; /* Descriptor status */
+ u8 errors; /* Descriptor Errors */
+ __le16 special;
+};
+
+/* Receive Descriptor - Extended */
+union e1000_rx_desc_extended {
+ struct {
+ __le64 buffer_addr;
+ __le64 reserved;
+ } read;
+ struct {
+ struct {
+ __le32 mrq; /* Multiple Rx Queues */
+ union {
+ __le32 rss; /* RSS Hash */
+ struct {
+ __le16 ip_id; /* IP id */
+ __le16 csum; /* Packet Checksum */
+ } csum_ip;
+ } hi_dword;
+ } lower;
+ struct {
+ __le32 status_error; /* ext status/error */
+ __le16 length;
+ __le16 vlan; /* VLAN tag */
+ } upper;
+ } wb; /* writeback */
+};
+
+#define MAX_PS_BUFFERS 4
+/* Receive Descriptor - Packet Split */
+union e1000_rx_desc_packet_split {
+ struct {
+ /* one buffer for protocol header(s), three data buffers */
+ __le64 buffer_addr[MAX_PS_BUFFERS];
+ } read;
+ struct {
+ struct {
+ __le32 mrq; /* Multiple Rx Queues */
+ union {
+ __le32 rss; /* RSS Hash */
+ struct {
+ __le16 ip_id; /* IP id */
+ __le16 csum; /* Packet Checksum */
+ } csum_ip;
+ } hi_dword;
+ } lower;
+ struct {
+ __le32 status_error; /* ext status/error */
+ __le16 length0; /* length of buffer 0 */
+ __le16 vlan; /* VLAN tag */
+ } middle;
+ struct {
+ __le16 header_status;
+ __le16 length[3]; /* length of buffers 1-3 */
+ } upper;
+ __le64 reserved;
+ } wb; /* writeback */
+};
+
+/* Transmit Descriptor */
+struct e1000_tx_desc {
+ __le64 buffer_addr; /* Address of the descriptor's data buffer */
+ union {
+ __le32 data;
+ struct {
+ __le16 length; /* Data buffer length */
+ u8 cso; /* Checksum offset */
+ u8 cmd; /* Descriptor control */
+ } flags;
+ } lower;
+ union {
+ __le32 data;
+ struct {
+ u8 status; /* Descriptor status */
+ u8 css; /* Checksum start */
+ __le16 special;
+ } fields;
+ } upper;
+};
+
+/* Offload Context Descriptor */
+struct e1000_context_desc {
+ union {
+ __le32 ip_config;
+ struct {
+ u8 ipcss; /* IP checksum start */
+ u8 ipcso; /* IP checksum offset */
+ __le16 ipcse; /* IP checksum end */
+ } ip_fields;
+ } lower_setup;
+ union {
+ __le32 tcp_config;
+ struct {
+ u8 tucss; /* TCP checksum start */
+ u8 tucso; /* TCP checksum offset */
+ __le16 tucse; /* TCP checksum end */
+ } tcp_fields;
+ } upper_setup;
+ __le32 cmd_and_length;
+ union {
+ __le32 data;
+ struct {
+ u8 status; /* Descriptor status */
+ u8 hdr_len; /* Header length */
+ __le16 mss; /* Maximum segment size */
+ } fields;
+ } tcp_seg_setup;
+};
+
+/* Offload data descriptor */
+struct e1000_data_desc {
+ __le64 buffer_addr; /* Address of the descriptor's buffer address */
+ union {
+ __le32 data;
+ struct {
+ __le16 length; /* Data buffer length */
+ u8 typ_len_ext;
+ u8 cmd;
+ } flags;
+ } lower;
+ union {
+ __le32 data;
+ struct {
+ u8 status; /* Descriptor status */
+ u8 popts; /* Packet Options */
+ __le16 special; /* */
+ } fields;
+ } upper;
+};
+
+/* Statistics counters collected by the MAC */
+struct e1000_hw_stats {
+ u64 crcerrs;
+ u64 algnerrc;
+ u64 symerrs;
+ u64 rxerrc;
+ u64 mpc;
+ u64 scc;
+ u64 ecol;
+ u64 mcc;
+ u64 latecol;
+ u64 colc;
+ u64 dc;
+ u64 tncrs;
+ u64 sec;
+ u64 cexterr;
+ u64 rlec;
+ u64 xonrxc;
+ u64 xontxc;
+ u64 xoffrxc;
+ u64 xofftxc;
+ u64 fcruc;
+ u64 prc64;
+ u64 prc127;
+ u64 prc255;
+ u64 prc511;
+ u64 prc1023;
+ u64 prc1522;
+ u64 gprc;
+ u64 bprc;
+ u64 mprc;
+ u64 gptc;
+ u64 gorc;
+ u64 gotc;
+ u64 rnbc;
+ u64 ruc;
+ u64 rfc;
+ u64 roc;
+ u64 rjc;
+ u64 mgprc;
+ u64 mgpdc;
+ u64 mgptc;
+ u64 tor;
+ u64 tot;
+ u64 tpr;
+ u64 tpt;
+ u64 ptc64;
+ u64 ptc127;
+ u64 ptc255;
+ u64 ptc511;
+ u64 ptc1023;
+ u64 ptc1522;
+ u64 mptc;
+ u64 bptc;
+ u64 tsctc;
+ u64 tsctfc;
+ u64 iac;
+ u64 icrxptc;
+ u64 icrxatc;
+ u64 ictxptc;
+ u64 ictxatc;
+ u64 ictxqec;
+ u64 ictxqmtc;
+ u64 icrxdmtc;
+ u64 icrxoc;
+};
+
+struct e1000_phy_stats {
+ u32 idle_errors;
+ u32 receive_errors;
+};
+
+struct e1000_host_mng_dhcp_cookie {
+ u32 signature;
+ u8 status;
+ u8 reserved0;
+ u16 vlan_id;
+ u32 reserved1;
+ u16 reserved2;
+ u8 reserved3;
+ u8 checksum;
+};
+
+/* Host Interface "Rev 1" */
+struct e1000_host_command_header {
+ u8 command_id;
+ u8 command_length;
+ u8 command_options;
+ u8 checksum;
+};
+
+#define E1000_HI_MAX_DATA_LENGTH 252
+struct e1000_host_command_info {
+ struct e1000_host_command_header command_header;
+ u8 command_data[E1000_HI_MAX_DATA_LENGTH];
+};
+
+/* Host Interface "Rev 2" */
+struct e1000_host_mng_command_header {
+ u8 command_id;
+ u8 checksum;
+ u16 reserved1;
+ u16 reserved2;
+ u16 command_length;
+};
+
+#define E1000_HI_MAX_MNG_DATA_LENGTH 0x6F8
+struct e1000_host_mng_command_info {
+ struct e1000_host_mng_command_header command_header;
+ u8 command_data[E1000_HI_MAX_MNG_DATA_LENGTH];
+};
+
+/* Function pointers and static data for the MAC. */
+struct e1000_mac_operations {
+ bool (*check_mng_mode)(struct e1000_hw *);
+ s32 (*check_for_link)(struct e1000_hw *);
+ s32 (*cleanup_led)(struct e1000_hw *);
+ void (*clear_hw_cntrs)(struct e1000_hw *);
+ s32 (*get_bus_info)(struct e1000_hw *);
+ s32 (*get_link_up_info)(struct e1000_hw *, u16 *, u16 *);
+ s32 (*led_on)(struct e1000_hw *);
+ s32 (*led_off)(struct e1000_hw *);
+ void (*update_mc_addr_list)(struct e1000_hw *, u8 *, u32, u32, u32);
+ s32 (*reset_hw)(struct e1000_hw *);
+ s32 (*init_hw)(struct e1000_hw *);
+ s32 (*setup_link)(struct e1000_hw *);
+ s32 (*setup_physical_interface)(struct e1000_hw *);
+};
+
+/* Function pointers for the PHY. */
+struct e1000_phy_operations {
+ s32 (*acquire_phy)(struct e1000_hw *);
+ s32 (*check_reset_block)(struct e1000_hw *);
+ s32 (*commit_phy)(struct e1000_hw *);
+ s32 (*force_speed_duplex)(struct e1000_hw *);
+ s32 (*get_cfg_done)(struct e1000_hw *hw);
+ s32 (*get_cable_length)(struct e1000_hw *);
+ s32 (*get_phy_info)(struct e1000_hw *);
+ s32 (*read_phy_reg)(struct e1000_hw *, u32, u16 *);
+ void (*release_phy)(struct e1000_hw *);
+ s32 (*reset_phy)(struct e1000_hw *);
+ s32 (*set_d0_lplu_state)(struct e1000_hw *, bool);
+ s32 (*set_d3_lplu_state)(struct e1000_hw *, bool);
+ s32 (*write_phy_reg)(struct e1000_hw *, u32, u16);
+};
+
+/* Function pointers for the NVM. */
+struct e1000_nvm_operations {
+ s32 (*acquire_nvm)(struct e1000_hw *);
+ s32 (*read_nvm)(struct e1000_hw *, u16, u16, u16 *);
+ void (*release_nvm)(struct e1000_hw *);
+ s32 (*update_nvm)(struct e1000_hw *);
+ s32 (*valid_led_default)(struct e1000_hw *, u16 *);
+ s32 (*validate_nvm)(struct e1000_hw *);
+ s32 (*write_nvm)(struct e1000_hw *, u16, u16, u16 *);
+};
+
+struct e1000_mac_info {
+ struct e1000_mac_operations ops;
+
+ u8 addr[6];
+ u8 perm_addr[6];
+
+ enum e1000_mac_type type;
+
+ u32 collision_delta;
+ u32 ledctl_default;
+ u32 ledctl_mode1;
+ u32 ledctl_mode2;
+ u32 mc_filter_type;
+ u32 tx_packet_delta;
+ u32 txcw;
+
+ u16 current_ifs_val;
+ u16 ifs_max_val;
+ u16 ifs_min_val;
+ u16 ifs_ratio;
+ u16 ifs_step_size;
+ u16 mta_reg_count;
+ u16 rar_entry_count;
+
+ u8 forced_speed_duplex;
+
+ bool arc_subsystem_valid;
+ bool autoneg;
+ bool autoneg_failed;
+ bool get_link_status;
+ bool in_ifs_mode;
+ bool serdes_has_link;
+ bool tx_pkt_filtering;
+};
+
+struct e1000_phy_info {
+ struct e1000_phy_operations ops;
+
+ enum e1000_phy_type type;
+
+ enum e1000_1000t_rx_status local_rx;
+ enum e1000_1000t_rx_status remote_rx;
+ enum e1000_ms_type ms_type;
+ enum e1000_ms_type original_ms_type;
+ enum e1000_rev_polarity cable_polarity;
+ enum e1000_smart_speed smart_speed;
+
+ u32 addr;
+ u32 id;
+ u32 reset_delay_us; /* in usec */
+ u32 revision;
+
+ enum e1000_media_type media_type;
+
+ u16 autoneg_advertised;
+ u16 autoneg_mask;
+ u16 cable_length;
+ u16 max_cable_length;
+ u16 min_cable_length;
+
+ u8 mdix;
+
+ bool disable_polarity_correction;
+ bool is_mdix;
+ bool polarity_correction;
+ bool speed_downgraded;
+ bool autoneg_wait_to_complete;
+};
+
+struct e1000_nvm_info {
+ struct e1000_nvm_operations ops;
+
+ enum e1000_nvm_type type;
+ enum e1000_nvm_override override;
+
+ u32 flash_bank_size;
+ u32 flash_base_addr;
+
+ u16 word_size;
+ u16 delay_usec;
+ u16 address_bits;
+ u16 opcode_bits;
+ u16 page_size;
+};
+
+struct e1000_bus_info {
+ enum e1000_bus_width width;
+
+ u16 func;
+};
+
+struct e1000_fc_info {
+ u32 high_water; /* Flow control high-water mark */
+ u32 low_water; /* Flow control low-water mark */
+ u16 pause_time; /* Flow control pause timer */
+ bool send_xon; /* Flow control send XON */
+ bool strict_ieee; /* Strict IEEE mode */
+ enum e1000_fc_type type; /* Type of flow control */
+ enum e1000_fc_type original_type;
+};
+
+struct e1000_dev_spec_82571 {
+ bool laa_is_present;
+ bool alt_mac_addr_is_present;
+};
+
+struct e1000_shadow_ram {
+ u16 value;
+ bool modified;
+};
+
+#define E1000_ICH8_SHADOW_RAM_WORDS 2048
+
+struct e1000_dev_spec_ich8lan {
+ bool kmrn_lock_loss_workaround_enabled;
+ struct e1000_shadow_ram shadow_ram[E1000_ICH8_SHADOW_RAM_WORDS];
+};
+
+struct e1000_hw {
+ struct e1000_adapter *adapter;
+
+ u8 __iomem *hw_addr;
+ u8 __iomem *flash_address;
+
+ struct e1000_mac_info mac;
+ struct e1000_fc_info fc;
+ struct e1000_phy_info phy;
+ struct e1000_nvm_info nvm;
+ struct e1000_bus_info bus;
+ struct e1000_host_mng_dhcp_cookie mng_cookie;
+
+ union {
+ struct e1000_dev_spec_82571 e82571;
+ struct e1000_dev_spec_ich8lan ich8lan;
+ } dev_spec;
+};
+
+#ifdef DEBUG
+#define hw_dbg(hw, format, arg...) \
+ printk(KERN_DEBUG "%s: " format, e1000e_get_hw_dev_name(hw), ##arg)
+#else
+static inline int __attribute__ ((format (printf, 2, 3)))
+hw_dbg(struct e1000_hw *hw, const char *format, ...)
+{
+ return 0;
+}
+#endif
+
+#endif
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2008 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+/*
+ * 82562G-2 10/100 Network Connection
+ * 82562GT 10/100 Network Connection
+ * 82562GT-2 10/100 Network Connection
+ * 82562V 10/100 Network Connection
+ * 82562V-2 10/100 Network Connection
+ * 82566DC-2 Gigabit Network Connection
+ * 82566DC Gigabit Network Connection
+ * 82566DM-2 Gigabit Network Connection
+ * 82566DM Gigabit Network Connection
+ * 82566MC Gigabit Network Connection
+ * 82566MM Gigabit Network Connection
+ * 82567LM Gigabit Network Connection
+ * 82567LF Gigabit Network Connection
+ * 82567LM-2 Gigabit Network Connection
+ * 82567LF-2 Gigabit Network Connection
+ * 82567V-2 Gigabit Network Connection
+ * 82567LF-3 Gigabit Network Connection
+ * 82567LM-3 Gigabit Network Connection
+ * 82567LM-4 Gigabit Network Connection
+ */
+
+#include <linux/netdevice.h>
+#include <linux/ethtool.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+
+#include "e1000.h"
+
+#define ICH_FLASH_GFPREG 0x0000
+#define ICH_FLASH_HSFSTS 0x0004
+#define ICH_FLASH_HSFCTL 0x0006
+#define ICH_FLASH_FADDR 0x0008
+#define ICH_FLASH_FDATA0 0x0010
+#define ICH_FLASH_PR0 0x0074
+
+#define ICH_FLASH_READ_COMMAND_TIMEOUT 500
+#define ICH_FLASH_WRITE_COMMAND_TIMEOUT 500
+#define ICH_FLASH_ERASE_COMMAND_TIMEOUT 3000000
+#define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF
+#define ICH_FLASH_CYCLE_REPEAT_COUNT 10
+
+#define ICH_CYCLE_READ 0
+#define ICH_CYCLE_WRITE 2
+#define ICH_CYCLE_ERASE 3
+
+#define FLASH_GFPREG_BASE_MASK 0x1FFF
+#define FLASH_SECTOR_ADDR_SHIFT 12
+
+#define ICH_FLASH_SEG_SIZE_256 256
+#define ICH_FLASH_SEG_SIZE_4K 4096
+#define ICH_FLASH_SEG_SIZE_8K 8192
+#define ICH_FLASH_SEG_SIZE_64K 65536
+
+
+#define E1000_ICH_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI Reset */
+
+#define E1000_ICH_MNG_IAMT_MODE 0x2
+
+#define ID_LED_DEFAULT_ICH8LAN ((ID_LED_DEF1_DEF2 << 12) | \
+ (ID_LED_DEF1_OFF2 << 8) | \
+ (ID_LED_DEF1_ON2 << 4) | \
+ (ID_LED_DEF1_DEF2))
+
+#define E1000_ICH_NVM_SIG_WORD 0x13
+#define E1000_ICH_NVM_SIG_MASK 0xC000
+
+#define E1000_ICH8_LAN_INIT_TIMEOUT 1500
+
+#define E1000_FEXTNVM_SW_CONFIG 1
+#define E1000_FEXTNVM_SW_CONFIG_ICH8M (1 << 27) /* Bit redefined for ICH8M :/ */
+
+#define PCIE_ICH8_SNOOP_ALL PCIE_NO_SNOOP_ALL
+
+#define E1000_ICH_RAR_ENTRIES 7
+
+#define PHY_PAGE_SHIFT 5
+#define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \
+ ((reg) & MAX_PHY_REG_ADDRESS))
+#define IGP3_KMRN_DIAG PHY_REG(770, 19) /* KMRN Diagnostic */
+#define IGP3_VR_CTRL PHY_REG(776, 18) /* Voltage Regulator Control */
+
+#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002
+#define IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK 0x0300
+#define IGP3_VR_CTRL_MODE_SHUTDOWN 0x0200
+
+/* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */
+/* Offset 04h HSFSTS */
+union ich8_hws_flash_status {
+ struct ich8_hsfsts {
+ u16 flcdone :1; /* bit 0 Flash Cycle Done */
+ u16 flcerr :1; /* bit 1 Flash Cycle Error */
+ u16 dael :1; /* bit 2 Direct Access error Log */
+ u16 berasesz :2; /* bit 4:3 Sector Erase Size */
+ u16 flcinprog :1; /* bit 5 flash cycle in Progress */
+ u16 reserved1 :2; /* bit 13:6 Reserved */
+ u16 reserved2 :6; /* bit 13:6 Reserved */
+ u16 fldesvalid :1; /* bit 14 Flash Descriptor Valid */
+ u16 flockdn :1; /* bit 15 Flash Config Lock-Down */
+ } hsf_status;
+ u16 regval;
+};
+
+/* ICH GbE Flash Hardware Sequencing Flash control Register bit breakdown */
+/* Offset 06h FLCTL */
+union ich8_hws_flash_ctrl {
+ struct ich8_hsflctl {
+ u16 flcgo :1; /* 0 Flash Cycle Go */
+ u16 flcycle :2; /* 2:1 Flash Cycle */
+ u16 reserved :5; /* 7:3 Reserved */
+ u16 fldbcount :2; /* 9:8 Flash Data Byte Count */
+ u16 flockdn :6; /* 15:10 Reserved */
+ } hsf_ctrl;
+ u16 regval;
+};
+
+/* ICH Flash Region Access Permissions */
+union ich8_hws_flash_regacc {
+ struct ich8_flracc {
+ u32 grra :8; /* 0:7 GbE region Read Access */
+ u32 grwa :8; /* 8:15 GbE region Write Access */
+ u32 gmrag :8; /* 23:16 GbE Master Read Access Grant */
+ u32 gmwag :8; /* 31:24 GbE Master Write Access Grant */
+ } hsf_flregacc;
+ u16 regval;
+};
+
+/* ICH Flash Protected Region */
+union ich8_flash_protected_range {
+ struct ich8_pr {
+ u32 base:13; /* 0:12 Protected Range Base */
+ u32 reserved1:2; /* 13:14 Reserved */
+ u32 rpe:1; /* 15 Read Protection Enable */
+ u32 limit:13; /* 16:28 Protected Range Limit */
+ u32 reserved2:2; /* 29:30 Reserved */
+ u32 wpe:1; /* 31 Write Protection Enable */
+ } range;
+ u32 regval;
+};
+
+static s32 e1000_setup_link_ich8lan(struct e1000_hw *hw);
+static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw);
+static void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw);
+static s32 e1000_check_polarity_ife_ich8lan(struct e1000_hw *hw);
+static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank);
+static s32 e1000_retry_write_flash_byte_ich8lan(struct e1000_hw *hw,
+ u32 offset, u8 byte);
+static s32 e1000_read_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset,
+ u8 *data);
+static s32 e1000_read_flash_word_ich8lan(struct e1000_hw *hw, u32 offset,
+ u16 *data);
+static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset,
+ u8 size, u16 *data);
+static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw);
+static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw);
+static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw);
+
+static inline u16 __er16flash(struct e1000_hw *hw, unsigned long reg)
+{
+ return readw(hw->flash_address + reg);
+}
+
+static inline u32 __er32flash(struct e1000_hw *hw, unsigned long reg)
+{
+ return readl(hw->flash_address + reg);
+}
+
+static inline void __ew16flash(struct e1000_hw *hw, unsigned long reg, u16 val)
+{
+ writew(val, hw->flash_address + reg);
+}
+
+static inline void __ew32flash(struct e1000_hw *hw, unsigned long reg, u32 val)
+{
+ writel(val, hw->flash_address + reg);
+}
+
+#define er16flash(reg) __er16flash(hw, (reg))
+#define er32flash(reg) __er32flash(hw, (reg))
+#define ew16flash(reg,val) __ew16flash(hw, (reg), (val))
+#define ew32flash(reg,val) __ew32flash(hw, (reg), (val))
+
+/**
+ * e1000_init_phy_params_ich8lan - Initialize PHY function pointers
+ * @hw: pointer to the HW structure
+ *
+ * Initialize family-specific PHY parameters and function pointers.
+ **/
+static s32 e1000_init_phy_params_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 i = 0;
+
+ phy->addr = 1;
+ phy->reset_delay_us = 100;
+
+ /*
+ * We may need to do this twice - once for IGP and if that fails,
+ * we'll set BM func pointers and try again
+ */
+ ret_val = e1000e_determine_phy_address(hw);
+ if (ret_val) {
+ hw->phy.ops.write_phy_reg = e1000e_write_phy_reg_bm;
+ hw->phy.ops.read_phy_reg = e1000e_read_phy_reg_bm;
+ ret_val = e1000e_determine_phy_address(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ phy->id = 0;
+ while ((e1000_phy_unknown == e1000e_get_phy_type_from_id(phy->id)) &&
+ (i++ < 100)) {
+ msleep(1);
+ ret_val = e1000e_get_phy_id(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Verify phy id */
+ switch (phy->id) {
+ case IGP03E1000_E_PHY_ID:
+ phy->type = e1000_phy_igp_3;
+ phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+ break;
+ case IFE_E_PHY_ID:
+ case IFE_PLUS_E_PHY_ID:
+ case IFE_C_E_PHY_ID:
+ phy->type = e1000_phy_ife;
+ phy->autoneg_mask = E1000_ALL_NOT_GIG;
+ break;
+ case BME1000_E_PHY_ID:
+ phy->type = e1000_phy_bm;
+ phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+ hw->phy.ops.read_phy_reg = e1000e_read_phy_reg_bm;
+ hw->phy.ops.write_phy_reg = e1000e_write_phy_reg_bm;
+ hw->phy.ops.commit_phy = e1000e_phy_sw_reset;
+ break;
+ default:
+ return -E1000_ERR_PHY;
+ break;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_init_nvm_params_ich8lan - Initialize NVM function pointers
+ * @hw: pointer to the HW structure
+ *
+ * Initialize family-specific NVM parameters and function
+ * pointers.
+ **/
+static s32 e1000_init_nvm_params_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
+ u32 gfpreg;
+ u32 sector_base_addr;
+ u32 sector_end_addr;
+ u16 i;
+
+ /* Can't read flash registers if the register set isn't mapped. */
+ if (!hw->flash_address) {
+ hw_dbg(hw, "ERROR: Flash registers not mapped\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ nvm->type = e1000_nvm_flash_sw;
+
+ gfpreg = er32flash(ICH_FLASH_GFPREG);
+
+ /*
+ * sector_X_addr is a "sector"-aligned address (4096 bytes)
+ * Add 1 to sector_end_addr since this sector is included in
+ * the overall size.
+ */
+ sector_base_addr = gfpreg & FLASH_GFPREG_BASE_MASK;
+ sector_end_addr = ((gfpreg >> 16) & FLASH_GFPREG_BASE_MASK) + 1;
+
+ /* flash_base_addr is byte-aligned */
+ nvm->flash_base_addr = sector_base_addr << FLASH_SECTOR_ADDR_SHIFT;
+
+ /*
+ * find total size of the NVM, then cut in half since the total
+ * size represents two separate NVM banks.
+ */
+ nvm->flash_bank_size = (sector_end_addr - sector_base_addr)
+ << FLASH_SECTOR_ADDR_SHIFT;
+ nvm->flash_bank_size /= 2;
+ /* Adjust to word count */
+ nvm->flash_bank_size /= sizeof(u16);
+
+ nvm->word_size = E1000_ICH8_SHADOW_RAM_WORDS;
+
+ /* Clear shadow ram */
+ for (i = 0; i < nvm->word_size; i++) {
+ dev_spec->shadow_ram[i].modified = 0;
+ dev_spec->shadow_ram[i].value = 0xFFFF;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_init_mac_params_ich8lan - Initialize MAC function pointers
+ * @hw: pointer to the HW structure
+ *
+ * Initialize family-specific MAC parameters and function
+ * pointers.
+ **/
+static s32 e1000_init_mac_params_ich8lan(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_mac_info *mac = &hw->mac;
+
+ /* Set media type function pointer */
+ hw->phy.media_type = e1000_media_type_copper;
+
+ /* Set mta register count */
+ mac->mta_reg_count = 32;
+ /* Set rar entry count */
+ mac->rar_entry_count = E1000_ICH_RAR_ENTRIES;
+ if (mac->type == e1000_ich8lan)
+ mac->rar_entry_count--;
+ /* Set if manageability features are enabled. */
+ mac->arc_subsystem_valid = 1;
+
+ /* Enable PCS Lock-loss workaround for ICH8 */
+ if (mac->type == e1000_ich8lan)
+ e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw, 1);
+
+ return 0;
+}
+
+static s32 e1000_get_variants_ich8lan(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ s32 rc;
+
+ rc = e1000_init_mac_params_ich8lan(adapter);
+ if (rc)
+ return rc;
+
+ rc = e1000_init_nvm_params_ich8lan(hw);
+ if (rc)
+ return rc;
+
+ rc = e1000_init_phy_params_ich8lan(hw);
+ if (rc)
+ return rc;
+
+ if ((adapter->hw.mac.type == e1000_ich8lan) &&
+ (adapter->hw.phy.type == e1000_phy_igp_3))
+ adapter->flags |= FLAG_LSC_GIG_SPEED_DROP;
+
+ return 0;
+}
+
+/**
+ * e1000_acquire_swflag_ich8lan - Acquire software control flag
+ * @hw: pointer to the HW structure
+ *
+ * Acquires the software control flag for performing NVM and PHY
+ * operations. This is a function pointer entry point only called by
+ * read/write routines for the PHY and NVM parts.
+ **/
+static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw)
+{
+ u32 extcnf_ctrl;
+ u32 timeout = PHY_CFG_TIMEOUT;
+
+ while (timeout) {
+ extcnf_ctrl = er32(EXTCNF_CTRL);
+ extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG;
+ ew32(EXTCNF_CTRL, extcnf_ctrl);
+
+ extcnf_ctrl = er32(EXTCNF_CTRL);
+ if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)
+ break;
+ mdelay(1);
+ timeout--;
+ }
+
+ if (!timeout) {
+ hw_dbg(hw, "FW or HW has locked the resource for too long.\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_release_swflag_ich8lan - Release software control flag
+ * @hw: pointer to the HW structure
+ *
+ * Releases the software control flag for performing NVM and PHY operations.
+ * This is a function pointer entry point only called by read/write
+ * routines for the PHY and NVM parts.
+ **/
+static void e1000_release_swflag_ich8lan(struct e1000_hw *hw)
+{
+ u32 extcnf_ctrl;
+
+ extcnf_ctrl = er32(EXTCNF_CTRL);
+ extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG;
+ ew32(EXTCNF_CTRL, extcnf_ctrl);
+}
+
+/**
+ * e1000_check_mng_mode_ich8lan - Checks management mode
+ * @hw: pointer to the HW structure
+ *
+ * This checks if the adapter has manageability enabled.
+ * This is a function pointer entry point only called by read/write
+ * routines for the PHY and NVM parts.
+ **/
+static bool e1000_check_mng_mode_ich8lan(struct e1000_hw *hw)
+{
+ u32 fwsm = er32(FWSM);
+
+ return (fwsm & E1000_FWSM_MODE_MASK) ==
+ (E1000_ICH_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT);
+}
+
+/**
+ * e1000_check_reset_block_ich8lan - Check if PHY reset is blocked
+ * @hw: pointer to the HW structure
+ *
+ * Checks if firmware is blocking the reset of the PHY.
+ * This is a function pointer entry point only called by
+ * reset routines.
+ **/
+static s32 e1000_check_reset_block_ich8lan(struct e1000_hw *hw)
+{
+ u32 fwsm;
+
+ fwsm = er32(FWSM);
+
+ return (fwsm & E1000_ICH_FWSM_RSPCIPHY) ? 0 : E1000_BLK_PHY_RESET;
+}
+
+/**
+ * e1000_phy_force_speed_duplex_ich8lan - Force PHY speed & duplex
+ * @hw: pointer to the HW structure
+ *
+ * Forces the speed and duplex settings of the PHY.
+ * This is a function pointer entry point only called by
+ * PHY setup routines.
+ **/
+static s32 e1000_phy_force_speed_duplex_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+ bool link;
+
+ if (phy->type != e1000_phy_ife) {
+ ret_val = e1000e_phy_force_speed_duplex_igp(hw);
+ return ret_val;
+ }
+
+ ret_val = e1e_rphy(hw, PHY_CONTROL, &data);
+ if (ret_val)
+ return ret_val;
+
+ e1000e_phy_force_speed_duplex_setup(hw, &data);
+
+ ret_val = e1e_wphy(hw, PHY_CONTROL, data);
+ if (ret_val)
+ return ret_val;
+
+ /* Disable MDI-X support for 10/100 */
+ ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, &data);
+ if (ret_val)
+ return ret_val;
+
+ data &= ~IFE_PMC_AUTO_MDIX;
+ data &= ~IFE_PMC_FORCE_MDIX;
+
+ ret_val = e1e_wphy(hw, IFE_PHY_MDIX_CONTROL, data);
+ if (ret_val)
+ return ret_val;
+
+ hw_dbg(hw, "IFE PMC: %X\n", data);
+
+ udelay(1);
+
+ if (phy->autoneg_wait_to_complete) {
+ hw_dbg(hw, "Waiting for forced speed/duplex link on IFE phy.\n");
+
+ ret_val = e1000e_phy_has_link_generic(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ return ret_val;
+
+ if (!link)
+ hw_dbg(hw, "Link taking longer than expected.\n");
+
+ /* Try once more */
+ ret_val = e1000e_phy_has_link_generic(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ return ret_val;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_phy_hw_reset_ich8lan - Performs a PHY reset
+ * @hw: pointer to the HW structure
+ *
+ * Resets the PHY
+ * This is a function pointer entry point called by drivers
+ * or other shared routines.
+ **/
+static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ u32 i;
+ u32 data, cnf_size, cnf_base_addr, sw_cfg_mask;
+ s32 ret_val;
+ u16 loop = E1000_ICH8_LAN_INIT_TIMEOUT;
+ u16 word_addr, reg_data, reg_addr, phy_page = 0;
+
+ ret_val = e1000e_phy_hw_reset_generic(hw);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Initialize the PHY from the NVM on ICH platforms. This
+ * is needed due to an issue where the NVM configuration is
+ * not properly autoloaded after power transitions.
+ * Therefore, after each PHY reset, we will load the
+ * configuration data out of the NVM manually.
+ */
+ if (hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) {
+ struct e1000_adapter *adapter = hw->adapter;
+
+ /* Check if SW needs configure the PHY */
+ if ((adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M_AMT) ||
+ (adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M))
+ sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M;
+ else
+ sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG;
+
+ data = er32(FEXTNVM);
+ if (!(data & sw_cfg_mask))
+ return 0;
+
+ /* Wait for basic configuration completes before proceeding*/
+ do {
+ data = er32(STATUS);
+ data &= E1000_STATUS_LAN_INIT_DONE;
+ udelay(100);
+ } while ((!data) && --loop);
+
+ /*
+ * If basic configuration is incomplete before the above loop
+ * count reaches 0, loading the configuration from NVM will
+ * leave the PHY in a bad state possibly resulting in no link.
+ */
+ if (loop == 0) {
+ hw_dbg(hw, "LAN_INIT_DONE not set, increase timeout\n");
+ }
+
+ /* Clear the Init Done bit for the next init event */
+ data = er32(STATUS);
+ data &= ~E1000_STATUS_LAN_INIT_DONE;
+ ew32(STATUS, data);
+
+ /*
+ * Make sure HW does not configure LCD from PHY
+ * extended configuration before SW configuration
+ */
+ data = er32(EXTCNF_CTRL);
+ if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE)
+ return 0;
+
+ cnf_size = er32(EXTCNF_SIZE);
+ cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK;
+ cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT;
+ if (!cnf_size)
+ return 0;
+
+ cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK;
+ cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT;
+
+ /* Configure LCD from extended configuration region. */
+
+ /* cnf_base_addr is in DWORD */
+ word_addr = (u16)(cnf_base_addr << 1);
+
+ for (i = 0; i < cnf_size; i++) {
+ ret_val = e1000_read_nvm(hw,
+ (word_addr + i * 2),
+ 1,
+ ®_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_nvm(hw,
+ (word_addr + i * 2 + 1),
+ 1,
+ ®_addr);
+ if (ret_val)
+ return ret_val;
+
+ /* Save off the PHY page for future writes. */
+ if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) {
+ phy_page = reg_data;
+ continue;
+ }
+
+ reg_addr |= phy_page;
+
+ ret_val = e1e_wphy(hw, (u32)reg_addr, reg_data);
+ if (ret_val)
+ return ret_val;
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_get_phy_info_ife_ich8lan - Retrieves various IFE PHY states
+ * @hw: pointer to the HW structure
+ *
+ * Populates "phy" structure with various feature states.
+ * This function is only called by other family-specific
+ * routines.
+ **/
+static s32 e1000_get_phy_info_ife_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+ bool link;
+
+ ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
+ if (ret_val)
+ return ret_val;
+
+ if (!link) {
+ hw_dbg(hw, "Phy info is only valid if link is up\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ ret_val = e1e_rphy(hw, IFE_PHY_SPECIAL_CONTROL, &data);
+ if (ret_val)
+ return ret_val;
+ phy->polarity_correction = (!(data & IFE_PSC_AUTO_POLARITY_DISABLE));
+
+ if (phy->polarity_correction) {
+ ret_val = e1000_check_polarity_ife_ich8lan(hw);
+ if (ret_val)
+ return ret_val;
+ } else {
+ /* Polarity is forced */
+ phy->cable_polarity = (data & IFE_PSC_FORCE_POLARITY)
+ ? e1000_rev_polarity_reversed
+ : e1000_rev_polarity_normal;
+ }
+
+ ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, &data);
+ if (ret_val)
+ return ret_val;
+
+ phy->is_mdix = (data & IFE_PMC_MDIX_STATUS);
+
+ /* The following parameters are undefined for 10/100 operation. */
+ phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
+ phy->local_rx = e1000_1000t_rx_status_undefined;
+ phy->remote_rx = e1000_1000t_rx_status_undefined;
+
+ return 0;
+}
+
+/**
+ * e1000_get_phy_info_ich8lan - Calls appropriate PHY type get_phy_info
+ * @hw: pointer to the HW structure
+ *
+ * Wrapper for calling the get_phy_info routines for the appropriate phy type.
+ * This is a function pointer entry point called by drivers
+ * or other shared routines.
+ **/
+static s32 e1000_get_phy_info_ich8lan(struct e1000_hw *hw)
+{
+ switch (hw->phy.type) {
+ case e1000_phy_ife:
+ return e1000_get_phy_info_ife_ich8lan(hw);
+ break;
+ case e1000_phy_igp_3:
+ case e1000_phy_bm:
+ return e1000e_get_phy_info_igp(hw);
+ break;
+ default:
+ break;
+ }
+
+ return -E1000_ERR_PHY_TYPE;
+}
+
+/**
+ * e1000_check_polarity_ife_ich8lan - Check cable polarity for IFE PHY
+ * @hw: pointer to the HW structure
+ *
+ * Polarity is determined on the polarity reversal feature being enabled.
+ * This function is only called by other family-specific
+ * routines.
+ **/
+static s32 e1000_check_polarity_ife_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data, offset, mask;
+
+ /*
+ * Polarity is determined based on the reversal feature being enabled.
+ */
+ if (phy->polarity_correction) {
+ offset = IFE_PHY_EXTENDED_STATUS_CONTROL;
+ mask = IFE_PESC_POLARITY_REVERSED;
+ } else {
+ offset = IFE_PHY_SPECIAL_CONTROL;
+ mask = IFE_PSC_FORCE_POLARITY;
+ }
+
+ ret_val = e1e_rphy(hw, offset, &phy_data);
+
+ if (!ret_val)
+ phy->cable_polarity = (phy_data & mask)
+ ? e1000_rev_polarity_reversed
+ : e1000_rev_polarity_normal;
+
+ return ret_val;
+}
+
+/**
+ * e1000_set_d0_lplu_state_ich8lan - Set Low Power Linkup D0 state
+ * @hw: pointer to the HW structure
+ * @active: TRUE to enable LPLU, FALSE to disable
+ *
+ * Sets the LPLU D0 state according to the active flag. When
+ * activating LPLU this function also disables smart speed
+ * and vice versa. LPLU will not be activated unless the
+ * device autonegotiation advertisement meets standards of
+ * either 10 or 10/100 or 10/100/1000 at all duplexes.
+ * This is a function pointer entry point only called by
+ * PHY setup routines.
+ **/
+static s32 e1000_set_d0_lplu_state_ich8lan(struct e1000_hw *hw, bool active)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ u32 phy_ctrl;
+ s32 ret_val = 0;
+ u16 data;
+
+ if (phy->type == e1000_phy_ife)
+ return ret_val;
+
+ phy_ctrl = er32(PHY_CTRL);
+
+ if (active) {
+ phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU;
+ ew32(PHY_CTRL, phy_ctrl);
+
+ /*
+ * Call gig speed drop workaround on LPLU before accessing
+ * any PHY registers
+ */
+ if ((hw->mac.type == e1000_ich8lan) &&
+ (hw->phy.type == e1000_phy_igp_3))
+ e1000e_gig_downshift_workaround_ich8lan(hw);
+
+ /* When LPLU is enabled, we should disable SmartSpeed */
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data);
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data);
+ if (ret_val)
+ return ret_val;
+ } else {
+ phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU;
+ ew32(PHY_CTRL, phy_ctrl);
+
+ /*
+ * LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ * during Dx states where the power conservation is most
+ * important. During driver activity we should enable
+ * SmartSpeed, so performance is maintained.
+ */
+ if (phy->smart_speed == e1000_smart_speed_on) {
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ return ret_val;
+
+ data |= IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ return ret_val;
+ } else if (phy->smart_speed == e1000_smart_speed_off) {
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ return ret_val;
+
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ return ret_val;
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_set_d3_lplu_state_ich8lan - Set Low Power Linkup D3 state
+ * @hw: pointer to the HW structure
+ * @active: TRUE to enable LPLU, FALSE to disable
+ *
+ * Sets the LPLU D3 state according to the active flag. When
+ * activating LPLU this function also disables smart speed
+ * and vice versa. LPLU will not be activated unless the
+ * device autonegotiation advertisement meets standards of
+ * either 10 or 10/100 or 10/100/1000 at all duplexes.
+ * This is a function pointer entry point only called by
+ * PHY setup routines.
+ **/
+static s32 e1000_set_d3_lplu_state_ich8lan(struct e1000_hw *hw, bool active)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ u32 phy_ctrl;
+ s32 ret_val;
+ u16 data;
+
+ phy_ctrl = er32(PHY_CTRL);
+
+ if (!active) {
+ phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU;
+ ew32(PHY_CTRL, phy_ctrl);
+ /*
+ * LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ * during Dx states where the power conservation is most
+ * important. During driver activity we should enable
+ * SmartSpeed, so performance is maintained.
+ */
+ if (phy->smart_speed == e1000_smart_speed_on) {
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ return ret_val;
+
+ data |= IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ return ret_val;
+ } else if (phy->smart_speed == e1000_smart_speed_off) {
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ return ret_val;
+
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ return ret_val;
+ }
+ } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) ||
+ (phy->autoneg_advertised == E1000_ALL_NOT_GIG) ||
+ (phy->autoneg_advertised == E1000_ALL_10_SPEED)) {
+ phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU;
+ ew32(PHY_CTRL, phy_ctrl);
+
+ /*
+ * Call gig speed drop workaround on LPLU before accessing
+ * any PHY registers
+ */
+ if ((hw->mac.type == e1000_ich8lan) &&
+ (hw->phy.type == e1000_phy_igp_3))
+ e1000e_gig_downshift_workaround_ich8lan(hw);
+
+ /* When LPLU is enabled, we should disable SmartSpeed */
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data);
+ if (ret_val)
+ return ret_val;
+
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data);
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_valid_nvm_bank_detect_ich8lan - finds out the valid bank 0 or 1
+ * @hw: pointer to the HW structure
+ * @bank: pointer to the variable that returns the active bank
+ *
+ * Reads signature byte from the NVM using the flash access registers.
+ **/
+static s32 e1000_valid_nvm_bank_detect_ich8lan(struct e1000_hw *hw, u32 *bank)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ /* flash bank size is in words */
+ u32 bank1_offset = nvm->flash_bank_size * sizeof(u16);
+ u32 act_offset = E1000_ICH_NVM_SIG_WORD * 2 + 1;
+ u8 bank_high_byte = 0;
+
+ if (hw->mac.type != e1000_ich10lan) {
+ if (er32(EECD) & E1000_EECD_SEC1VAL)
+ *bank = 1;
+ else
+ *bank = 0;
+ } else {
+ /*
+ * Make sure the signature for bank 0 is valid,
+ * if not check for bank1
+ */
+ e1000_read_flash_byte_ich8lan(hw, act_offset, &bank_high_byte);
+ if ((bank_high_byte & 0xC0) == 0x80) {
+ *bank = 0;
+ } else {
+ /*
+ * find if segment 1 is valid by verifying
+ * bit 15:14 = 10b in word 0x13
+ */
+ e1000_read_flash_byte_ich8lan(hw,
+ act_offset + bank1_offset,
+ &bank_high_byte);
+
+ /* bank1 has a valid signature equivalent to SEC1V */
+ if ((bank_high_byte & 0xC0) == 0x80) {
+ *bank = 1;
+ } else {
+ hw_dbg(hw, "ERROR: EEPROM not present\n");
+ return -E1000_ERR_NVM;
+ }
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_read_nvm_ich8lan - Read word(s) from the NVM
+ * @hw: pointer to the HW structure
+ * @offset: The offset (in bytes) of the word(s) to read.
+ * @words: Size of data to read in words
+ * @data: Pointer to the word(s) to read at offset.
+ *
+ * Reads a word(s) from the NVM using the flash access registers.
+ **/
+static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
+ u32 act_offset;
+ s32 ret_val;
+ u32 bank = 0;
+ u16 i, word;
+
+ if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) ||
+ (words == 0)) {
+ hw_dbg(hw, "nvm parameter(s) out of bounds\n");
+ return -E1000_ERR_NVM;
+ }
+
+ ret_val = e1000_acquire_swflag_ich8lan(hw);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank);
+ if (ret_val)
+ return ret_val;
+
+ act_offset = (bank) ? nvm->flash_bank_size : 0;
+ act_offset += offset;
+
+ for (i = 0; i < words; i++) {
+ if ((dev_spec->shadow_ram) &&
+ (dev_spec->shadow_ram[offset+i].modified)) {
+ data[i] = dev_spec->shadow_ram[offset+i].value;
+ } else {
+ ret_val = e1000_read_flash_word_ich8lan(hw,
+ act_offset + i,
+ &word);
+ if (ret_val)
+ break;
+ data[i] = word;
+ }
+ }
+
+ e1000_release_swflag_ich8lan(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_flash_cycle_init_ich8lan - Initialize flash
+ * @hw: pointer to the HW structure
+ *
+ * This function does initial flash setup so that a new read/write/erase cycle
+ * can be started.
+ **/
+static s32 e1000_flash_cycle_init_ich8lan(struct e1000_hw *hw)
+{
+ union ich8_hws_flash_status hsfsts;
+ s32 ret_val = -E1000_ERR_NVM;
+ s32 i = 0;
+
+ hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
+
+ /* Check if the flash descriptor is valid */
+ if (hsfsts.hsf_status.fldesvalid == 0) {
+ hw_dbg(hw, "Flash descriptor invalid. "
+ "SW Sequencing must be used.");
+ return -E1000_ERR_NVM;
+ }
+
+ /* Clear FCERR and DAEL in hw status by writing 1 */
+ hsfsts.hsf_status.flcerr = 1;
+ hsfsts.hsf_status.dael = 1;
+
+ ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval);
+
+ /*
+ * Either we should have a hardware SPI cycle in progress
+ * bit to check against, in order to start a new cycle or
+ * FDONE bit should be changed in the hardware so that it
+ * is 1 after hardware reset, which can then be used as an
+ * indication whether a cycle is in progress or has been
+ * completed.
+ */
+
+ if (hsfsts.hsf_status.flcinprog == 0) {
+ /*
+ * There is no cycle running at present,
+ * so we can start a cycle
+ * Begin by setting Flash Cycle Done.
+ */
+ hsfsts.hsf_status.flcdone = 1;
+ ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval);
+ ret_val = 0;
+ } else {
+ /*
+ * otherwise poll for sometime so the current
+ * cycle has a chance to end before giving up.
+ */
+ for (i = 0; i < ICH_FLASH_READ_COMMAND_TIMEOUT; i++) {
+ hsfsts.regval = __er16flash(hw, ICH_FLASH_HSFSTS);
+ if (hsfsts.hsf_status.flcinprog == 0) {
+ ret_val = 0;
+ break;
+ }
+ udelay(1);
+ }
+ if (ret_val == 0) {
+ /*
+ * Successful in waiting for previous cycle to timeout,
+ * now set the Flash Cycle Done.
+ */
+ hsfsts.hsf_status.flcdone = 1;
+ ew16flash(ICH_FLASH_HSFSTS, hsfsts.regval);
+ } else {
+ hw_dbg(hw, "Flash controller busy, cannot get access");
+ }
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000_flash_cycle_ich8lan - Starts flash cycle (read/write/erase)
+ * @hw: pointer to the HW structure
+ * @timeout: maximum time to wait for completion
+ *
+ * This function starts a flash cycle and waits for its completion.
+ **/
+static s32 e1000_flash_cycle_ich8lan(struct e1000_hw *hw, u32 timeout)
+{
+ union ich8_hws_flash_ctrl hsflctl;
+ union ich8_hws_flash_status hsfsts;
+ s32 ret_val = -E1000_ERR_NVM;
+ u32 i = 0;
+
+ /* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */
+ hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
+ hsflctl.hsf_ctrl.flcgo = 1;
+ ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
+
+ /* wait till FDONE bit is set to 1 */
+ do {
+ hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
+ if (hsfsts.hsf_status.flcdone == 1)
+ break;
+ udelay(1);
+ } while (i++ < timeout);
+
+ if (hsfsts.hsf_status.flcdone == 1 && hsfsts.hsf_status.flcerr == 0)
+ return 0;
+
+ return ret_val;
+}
+
+/**
+ * e1000_read_flash_word_ich8lan - Read word from flash
+ * @hw: pointer to the HW structure
+ * @offset: offset to data location
+ * @data: pointer to the location for storing the data
+ *
+ * Reads the flash word at offset into data. Offset is converted
+ * to bytes before read.
+ **/
+static s32 e1000_read_flash_word_ich8lan(struct e1000_hw *hw, u32 offset,
+ u16 *data)
+{
+ /* Must convert offset into bytes. */
+ offset <<= 1;
+
+ return e1000_read_flash_data_ich8lan(hw, offset, 2, data);
+}
+
+/**
+ * e1000_read_flash_byte_ich8lan - Read byte from flash
+ * @hw: pointer to the HW structure
+ * @offset: The offset of the byte to read.
+ * @data: Pointer to a byte to store the value read.
+ *
+ * Reads a single byte from the NVM using the flash access registers.
+ **/
+static s32 e1000_read_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset,
+ u8 *data)
+{
+ s32 ret_val;
+ u16 word = 0;
+
+ ret_val = e1000_read_flash_data_ich8lan(hw, offset, 1, &word);
+ if (ret_val)
+ return ret_val;
+
+ *data = (u8)word;
+
+ return 0;
+}
+
+/**
+ * e1000_read_flash_data_ich8lan - Read byte or word from NVM
+ * @hw: pointer to the HW structure
+ * @offset: The offset (in bytes) of the byte or word to read.
+ * @size: Size of data to read, 1=byte 2=word
+ * @data: Pointer to the word to store the value read.
+ *
+ * Reads a byte or word from the NVM using the flash access registers.
+ **/
+static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset,
+ u8 size, u16 *data)
+{
+ union ich8_hws_flash_status hsfsts;
+ union ich8_hws_flash_ctrl hsflctl;
+ u32 flash_linear_addr;
+ u32 flash_data = 0;
+ s32 ret_val = -E1000_ERR_NVM;
+ u8 count = 0;
+
+ if (size < 1 || size > 2 || offset > ICH_FLASH_LINEAR_ADDR_MASK)
+ return -E1000_ERR_NVM;
+
+ flash_linear_addr = (ICH_FLASH_LINEAR_ADDR_MASK & offset) +
+ hw->nvm.flash_base_addr;
+
+ do {
+ udelay(1);
+ /* Steps */
+ ret_val = e1000_flash_cycle_init_ich8lan(hw);
+ if (ret_val != 0)
+ break;
+
+ hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
+ /* 0b/1b corresponds to 1 or 2 byte size, respectively. */
+ hsflctl.hsf_ctrl.fldbcount = size - 1;
+ hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_READ;
+ ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
+
+ ew32flash(ICH_FLASH_FADDR, flash_linear_addr);
+
+ ret_val = e1000_flash_cycle_ich8lan(hw,
+ ICH_FLASH_READ_COMMAND_TIMEOUT);
+
+ /*
+ * Check if FCERR is set to 1, if set to 1, clear it
+ * and try the whole sequence a few more times, else
+ * read in (shift in) the Flash Data0, the order is
+ * least significant byte first msb to lsb
+ */
+ if (ret_val == 0) {
+ flash_data = er32flash(ICH_FLASH_FDATA0);
+ if (size == 1) {
+ *data = (u8)(flash_data & 0x000000FF);
+ } else if (size == 2) {
+ *data = (u16)(flash_data & 0x0000FFFF);
+ }
+ break;
+ } else {
+ /*
+ * If we've gotten here, then things are probably
+ * completely hosed, but if the error condition is
+ * detected, it won't hurt to give it another try...
+ * ICH_FLASH_CYCLE_REPEAT_COUNT times.
+ */
+ hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
+ if (hsfsts.hsf_status.flcerr == 1) {
+ /* Repeat for some time before giving up. */
+ continue;
+ } else if (hsfsts.hsf_status.flcdone == 0) {
+ hw_dbg(hw, "Timeout error - flash cycle "
+ "did not complete.");
+ break;
+ }
+ }
+ } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT);
+
+ return ret_val;
+}
+
+/**
+ * e1000_write_nvm_ich8lan - Write word(s) to the NVM
+ * @hw: pointer to the HW structure
+ * @offset: The offset (in bytes) of the word(s) to write.
+ * @words: Size of data to write in words
+ * @data: Pointer to the word(s) to write at offset.
+ *
+ * Writes a byte or word to the NVM using the flash access registers.
+ **/
+static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
+ s32 ret_val;
+ u16 i;
+
+ if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) ||
+ (words == 0)) {
+ hw_dbg(hw, "nvm parameter(s) out of bounds\n");
+ return -E1000_ERR_NVM;
+ }
+
+ ret_val = e1000_acquire_swflag_ich8lan(hw);
+ if (ret_val)
+ return ret_val;
+
+ for (i = 0; i < words; i++) {
+ dev_spec->shadow_ram[offset+i].modified = 1;
+ dev_spec->shadow_ram[offset+i].value = data[i];
+ }
+
+ e1000_release_swflag_ich8lan(hw);
+
+ return 0;
+}
+
+/**
+ * e1000_update_nvm_checksum_ich8lan - Update the checksum for NVM
+ * @hw: pointer to the HW structure
+ *
+ * The NVM checksum is updated by calling the generic update_nvm_checksum,
+ * which writes the checksum to the shadow ram. The changes in the shadow
+ * ram are then committed to the EEPROM by processing each bank at a time
+ * checking for the modified bit and writing only the pending changes.
+ * After a successful commit, the shadow ram is cleared and is ready for
+ * future writes.
+ **/
+static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
+ u32 i, act_offset, new_bank_offset, old_bank_offset, bank;
+ s32 ret_val;
+ u16 data;
+
+ ret_val = e1000e_update_nvm_checksum_generic(hw);
+ if (ret_val)
+ return ret_val;
+
+ if (nvm->type != e1000_nvm_flash_sw)
+ return ret_val;
+
+ ret_val = e1000_acquire_swflag_ich8lan(hw);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * We're writing to the opposite bank so if we're on bank 1,
+ * write to bank 0 etc. We also need to erase the segment that
+ * is going to be written
+ */
+ ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank);
+ if (ret_val)
+ return ret_val;
+
+ if (bank == 0) {
+ new_bank_offset = nvm->flash_bank_size;
+ old_bank_offset = 0;
+ e1000_erase_flash_bank_ich8lan(hw, 1);
+ } else {
+ old_bank_offset = nvm->flash_bank_size;
+ new_bank_offset = 0;
+ e1000_erase_flash_bank_ich8lan(hw, 0);
+ }
+
+ for (i = 0; i < E1000_ICH8_SHADOW_RAM_WORDS; i++) {
+ /*
+ * Determine whether to write the value stored
+ * in the other NVM bank or a modified value stored
+ * in the shadow RAM
+ */
+ if (dev_spec->shadow_ram[i].modified) {
+ data = dev_spec->shadow_ram[i].value;
+ } else {
+ e1000_read_flash_word_ich8lan(hw,
+ i + old_bank_offset,
+ &data);
+ }
+
+ /*
+ * If the word is 0x13, then make sure the signature bits
+ * (15:14) are 11b until the commit has completed.
+ * This will allow us to write 10b which indicates the
+ * signature is valid. We want to do this after the write
+ * has completed so that we don't mark the segment valid
+ * while the write is still in progress
+ */
+ if (i == E1000_ICH_NVM_SIG_WORD)
+ data |= E1000_ICH_NVM_SIG_MASK;
+
+ /* Convert offset to bytes. */
+ act_offset = (i + new_bank_offset) << 1;
+
+ udelay(100);
+ /* Write the bytes to the new bank. */
+ ret_val = e1000_retry_write_flash_byte_ich8lan(hw,
+ act_offset,
+ (u8)data);
+ if (ret_val)
+ break;
+
+ udelay(100);
+ ret_val = e1000_retry_write_flash_byte_ich8lan(hw,
+ act_offset + 1,
+ (u8)(data >> 8));
+ if (ret_val)
+ break;
+ }
+
+ /*
+ * Don't bother writing the segment valid bits if sector
+ * programming failed.
+ */
+ if (ret_val) {
+ /* Possibly read-only, see e1000e_write_protect_nvm_ich8lan() */
+ hw_dbg(hw, "Flash commit failed.\n");
+ e1000_release_swflag_ich8lan(hw);
+ return ret_val;
+ }
+
+ /*
+ * Finally validate the new segment by setting bit 15:14
+ * to 10b in word 0x13 , this can be done without an
+ * erase as well since these bits are 11 to start with
+ * and we need to change bit 14 to 0b
+ */
+ act_offset = new_bank_offset + E1000_ICH_NVM_SIG_WORD;
+ e1000_read_flash_word_ich8lan(hw, act_offset, &data);
+ data &= 0xBFFF;
+ ret_val = e1000_retry_write_flash_byte_ich8lan(hw,
+ act_offset * 2 + 1,
+ (u8)(data >> 8));
+ if (ret_val) {
+ e1000_release_swflag_ich8lan(hw);
+ return ret_val;
+ }
+
+ /*
+ * And invalidate the previously valid segment by setting
+ * its signature word (0x13) high_byte to 0b. This can be
+ * done without an erase because flash erase sets all bits
+ * to 1's. We can write 1's to 0's without an erase
+ */
+ act_offset = (old_bank_offset + E1000_ICH_NVM_SIG_WORD) * 2 + 1;
+ ret_val = e1000_retry_write_flash_byte_ich8lan(hw, act_offset, 0);
+ if (ret_val) {
+ e1000_release_swflag_ich8lan(hw);
+ return ret_val;
+ }
+
+ /* Great! Everything worked, we can now clear the cached entries. */
+ for (i = 0; i < E1000_ICH8_SHADOW_RAM_WORDS; i++) {
+ dev_spec->shadow_ram[i].modified = 0;
+ dev_spec->shadow_ram[i].value = 0xFFFF;
+ }
+
+ e1000_release_swflag_ich8lan(hw);
+
+ /*
+ * Reload the EEPROM, or else modifications will not appear
+ * until after the next adapter reset.
+ */
+ e1000e_reload_nvm(hw);
+ msleep(10);
+
+ return ret_val;
+}
+
+/**
+ * e1000_validate_nvm_checksum_ich8lan - Validate EEPROM checksum
+ * @hw: pointer to the HW structure
+ *
+ * Check to see if checksum needs to be fixed by reading bit 6 in word 0x19.
+ * If the bit is 0, that the EEPROM had been modified, but the checksum was not
+ * calculated, in which case we need to calculate the checksum and set bit 6.
+ **/
+static s32 e1000_validate_nvm_checksum_ich8lan(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 data;
+
+ /*
+ * Read 0x19 and check bit 6. If this bit is 0, the checksum
+ * needs to be fixed. This bit is an indication that the NVM
+ * was prepared by OEM software and did not calculate the
+ * checksum...a likely scenario.
+ */
+ ret_val = e1000_read_nvm(hw, 0x19, 1, &data);
+ if (ret_val)
+ return ret_val;
+
+ if ((data & 0x40) == 0) {
+ data |= 0x40;
+ ret_val = e1000_write_nvm(hw, 0x19, 1, &data);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000e_update_nvm_checksum(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ return e1000e_validate_nvm_checksum_generic(hw);
+}
+
+/**
+ * e1000e_write_protect_nvm_ich8lan - Make the NVM read-only
+ * @hw: pointer to the HW structure
+ *
+ * To prevent malicious write/erase of the NVM, set it to be read-only
+ * so that the hardware ignores all write/erase cycles of the NVM via
+ * the flash control registers. The shadow-ram copy of the NVM will
+ * still be updated, however any updates to this copy will not stick
+ * across driver reloads.
+ **/
+void e1000e_write_protect_nvm_ich8lan(struct e1000_hw *hw)
+{
+ union ich8_flash_protected_range pr0;
+ union ich8_hws_flash_status hsfsts;
+ u32 gfpreg;
+ s32 ret_val;
+
+ ret_val = e1000_acquire_swflag_ich8lan(hw);
+ if (ret_val)
+ return;
+
+ gfpreg = er32flash(ICH_FLASH_GFPREG);
+
+ /* Write-protect GbE Sector of NVM */
+ pr0.regval = er32flash(ICH_FLASH_PR0);
+ pr0.range.base = gfpreg & FLASH_GFPREG_BASE_MASK;
+ pr0.range.limit = ((gfpreg >> 16) & FLASH_GFPREG_BASE_MASK);
+ pr0.range.wpe = true;
+ ew32flash(ICH_FLASH_PR0, pr0.regval);
+
+ /*
+ * Lock down a subset of GbE Flash Control Registers, e.g.
+ * PR0 to prevent the write-protection from being lifted.
+ * Once FLOCKDN is set, the registers protected by it cannot
+ * be written until FLOCKDN is cleared by a hardware reset.
+ */
+ hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
+ hsfsts.hsf_status.flockdn = true;
+ ew32flash(ICH_FLASH_HSFSTS, hsfsts.regval);
+
+ e1000_release_swflag_ich8lan(hw);
+}
+
+/**
+ * e1000_write_flash_data_ich8lan - Writes bytes to the NVM
+ * @hw: pointer to the HW structure
+ * @offset: The offset (in bytes) of the byte/word to read.
+ * @size: Size of data to read, 1=byte 2=word
+ * @data: The byte(s) to write to the NVM.
+ *
+ * Writes one/two bytes to the NVM using the flash access registers.
+ **/
+static s32 e1000_write_flash_data_ich8lan(struct e1000_hw *hw, u32 offset,
+ u8 size, u16 data)
+{
+ union ich8_hws_flash_status hsfsts;
+ union ich8_hws_flash_ctrl hsflctl;
+ u32 flash_linear_addr;
+ u32 flash_data = 0;
+ s32 ret_val;
+ u8 count = 0;
+
+ if (size < 1 || size > 2 || data > size * 0xff ||
+ offset > ICH_FLASH_LINEAR_ADDR_MASK)
+ return -E1000_ERR_NVM;
+
+ flash_linear_addr = (ICH_FLASH_LINEAR_ADDR_MASK & offset) +
+ hw->nvm.flash_base_addr;
+
+ do {
+ udelay(1);
+ /* Steps */
+ ret_val = e1000_flash_cycle_init_ich8lan(hw);
+ if (ret_val)
+ break;
+
+ hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
+ /* 0b/1b corresponds to 1 or 2 byte size, respectively. */
+ hsflctl.hsf_ctrl.fldbcount = size -1;
+ hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_WRITE;
+ ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
+
+ ew32flash(ICH_FLASH_FADDR, flash_linear_addr);
+
+ if (size == 1)
+ flash_data = (u32)data & 0x00FF;
+ else
+ flash_data = (u32)data;
+
+ ew32flash(ICH_FLASH_FDATA0, flash_data);
+
+ /*
+ * check if FCERR is set to 1 , if set to 1, clear it
+ * and try the whole sequence a few more times else done
+ */
+ ret_val = e1000_flash_cycle_ich8lan(hw,
+ ICH_FLASH_WRITE_COMMAND_TIMEOUT);
+ if (!ret_val)
+ break;
+
+ /*
+ * If we're here, then things are most likely
+ * completely hosed, but if the error condition
+ * is detected, it won't hurt to give it another
+ * try...ICH_FLASH_CYCLE_REPEAT_COUNT times.
+ */
+ hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
+ if (hsfsts.hsf_status.flcerr == 1)
+ /* Repeat for some time before giving up. */
+ continue;
+ if (hsfsts.hsf_status.flcdone == 0) {
+ hw_dbg(hw, "Timeout error - flash cycle "
+ "did not complete.");
+ break;
+ }
+ } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT);
+
+ return ret_val;
+}
+
+/**
+ * e1000_write_flash_byte_ich8lan - Write a single byte to NVM
+ * @hw: pointer to the HW structure
+ * @offset: The index of the byte to read.
+ * @data: The byte to write to the NVM.
+ *
+ * Writes a single byte to the NVM using the flash access registers.
+ **/
+static s32 e1000_write_flash_byte_ich8lan(struct e1000_hw *hw, u32 offset,
+ u8 data)
+{
+ u16 word = (u16)data;
+
+ return e1000_write_flash_data_ich8lan(hw, offset, 1, word);
+}
+
+/**
+ * e1000_retry_write_flash_byte_ich8lan - Writes a single byte to NVM
+ * @hw: pointer to the HW structure
+ * @offset: The offset of the byte to write.
+ * @byte: The byte to write to the NVM.
+ *
+ * Writes a single byte to the NVM using the flash access registers.
+ * Goes through a retry algorithm before giving up.
+ **/
+static s32 e1000_retry_write_flash_byte_ich8lan(struct e1000_hw *hw,
+ u32 offset, u8 byte)
+{
+ s32 ret_val;
+ u16 program_retries;
+
+ ret_val = e1000_write_flash_byte_ich8lan(hw, offset, byte);
+ if (!ret_val)
+ return ret_val;
+
+ for (program_retries = 0; program_retries < 100; program_retries++) {
+ hw_dbg(hw, "Retrying Byte %2.2X at offset %u\n", byte, offset);
+ udelay(100);
+ ret_val = e1000_write_flash_byte_ich8lan(hw, offset, byte);
+ if (!ret_val)
+ break;
+ }
+ if (program_retries == 100)
+ return -E1000_ERR_NVM;
+
+ return 0;
+}
+
+/**
+ * e1000_erase_flash_bank_ich8lan - Erase a bank (4k) from NVM
+ * @hw: pointer to the HW structure
+ * @bank: 0 for first bank, 1 for second bank, etc.
+ *
+ * Erases the bank specified. Each bank is a 4k block. Banks are 0 based.
+ * bank N is 4096 * N + flash_reg_addr.
+ **/
+static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ union ich8_hws_flash_status hsfsts;
+ union ich8_hws_flash_ctrl hsflctl;
+ u32 flash_linear_addr;
+ /* bank size is in 16bit words - adjust to bytes */
+ u32 flash_bank_size = nvm->flash_bank_size * 2;
+ s32 ret_val;
+ s32 count = 0;
+ s32 iteration;
+ s32 sector_size;
+ s32 j;
+
+ hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
+
+ /*
+ * Determine HW Sector size: Read BERASE bits of hw flash status
+ * register
+ * 00: The Hw sector is 256 bytes, hence we need to erase 16
+ * consecutive sectors. The start index for the nth Hw sector
+ * can be calculated as = bank * 4096 + n * 256
+ * 01: The Hw sector is 4K bytes, hence we need to erase 1 sector.
+ * The start index for the nth Hw sector can be calculated
+ * as = bank * 4096
+ * 10: The Hw sector is 8K bytes, nth sector = bank * 8192
+ * (ich9 only, otherwise error condition)
+ * 11: The Hw sector is 64K bytes, nth sector = bank * 65536
+ */
+ switch (hsfsts.hsf_status.berasesz) {
+ case 0:
+ /* Hw sector size 256 */
+ sector_size = ICH_FLASH_SEG_SIZE_256;
+ iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_256;
+ break;
+ case 1:
+ sector_size = ICH_FLASH_SEG_SIZE_4K;
+ iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_4K;
+ break;
+ case 2:
+ if (hw->mac.type == e1000_ich9lan) {
+ sector_size = ICH_FLASH_SEG_SIZE_8K;
+ iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_8K;
+ } else {
+ return -E1000_ERR_NVM;
+ }
+ break;
+ case 3:
+ sector_size = ICH_FLASH_SEG_SIZE_64K;
+ iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_64K;
+ break;
+ default:
+ return -E1000_ERR_NVM;
+ }
+
+ /* Start with the base address, then add the sector offset. */
+ flash_linear_addr = hw->nvm.flash_base_addr;
+ flash_linear_addr += (bank) ? (sector_size * iteration) : 0;
+
+ for (j = 0; j < iteration ; j++) {
+ do {
+ /* Steps */
+ ret_val = e1000_flash_cycle_init_ich8lan(hw);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Write a value 11 (block Erase) in Flash
+ * Cycle field in hw flash control
+ */
+ hsflctl.regval = er16flash(ICH_FLASH_HSFCTL);
+ hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_ERASE;
+ ew16flash(ICH_FLASH_HSFCTL, hsflctl.regval);
+
+ /*
+ * Write the last 24 bits of an index within the
+ * block into Flash Linear address field in Flash
+ * Address.
+ */
+ flash_linear_addr += (j * sector_size);
+ ew32flash(ICH_FLASH_FADDR, flash_linear_addr);
+
+ ret_val = e1000_flash_cycle_ich8lan(hw,
+ ICH_FLASH_ERASE_COMMAND_TIMEOUT);
+ if (ret_val == 0)
+ break;
+
+ /*
+ * Check if FCERR is set to 1. If 1,
+ * clear it and try the whole sequence
+ * a few more times else Done
+ */
+ hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
+ if (hsfsts.hsf_status.flcerr == 1)
+ /* repeat for some time before giving up */
+ continue;
+ else if (hsfsts.hsf_status.flcdone == 0)
+ return ret_val;
+ } while (++count < ICH_FLASH_CYCLE_REPEAT_COUNT);
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_valid_led_default_ich8lan - Set the default LED settings
+ * @hw: pointer to the HW structure
+ * @data: Pointer to the LED settings
+ *
+ * Reads the LED default settings from the NVM to data. If the NVM LED
+ * settings is all 0's or F's, set the LED default to a valid LED default
+ * setting.
+ **/
+static s32 e1000_valid_led_default_ich8lan(struct e1000_hw *hw, u16 *data)
+{
+ s32 ret_val;
+
+ ret_val = e1000_read_nvm(hw, NVM_ID_LED_SETTINGS, 1, data);
+ if (ret_val) {
+ hw_dbg(hw, "NVM Read Error\n");
+ return ret_val;
+ }
+
+ if (*data == ID_LED_RESERVED_0000 ||
+ *data == ID_LED_RESERVED_FFFF)
+ *data = ID_LED_DEFAULT_ICH8LAN;
+
+ return 0;
+}
+
+/**
+ * e1000_get_bus_info_ich8lan - Get/Set the bus type and width
+ * @hw: pointer to the HW structure
+ *
+ * ICH8 use the PCI Express bus, but does not contain a PCI Express Capability
+ * register, so the the bus width is hard coded.
+ **/
+static s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_bus_info *bus = &hw->bus;
+ s32 ret_val;
+
+ ret_val = e1000e_get_bus_info_pcie(hw);
+
+ /*
+ * ICH devices are "PCI Express"-ish. They have
+ * a configuration space, but do not contain
+ * PCI Express Capability registers, so bus width
+ * must be hardcoded.
+ */
+ if (bus->width == e1000_bus_width_unknown)
+ bus->width = e1000_bus_width_pcie_x1;
+
+ return ret_val;
+}
+
+/**
+ * e1000_reset_hw_ich8lan - Reset the hardware
+ * @hw: pointer to the HW structure
+ *
+ * Does a full reset of the hardware which includes a reset of the PHY and
+ * MAC.
+ **/
+static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
+{
+ u32 ctrl, icr, kab;
+ s32 ret_val;
+
+ /*
+ * Prevent the PCI-E bus from sticking if there is no TLP connection
+ * on the last TLP read/write transaction when MAC is reset.
+ */
+ ret_val = e1000e_disable_pcie_master(hw);
+ if (ret_val) {
+ hw_dbg(hw, "PCI-E Master disable polling has failed.\n");
+ }
+
+ hw_dbg(hw, "Masking off all interrupts\n");
+ ew32(IMC, 0xffffffff);
+
+ /*
+ * Disable the Transmit and Receive units. Then delay to allow
+ * any pending transactions to complete before we hit the MAC
+ * with the global reset.
+ */
+ ew32(RCTL, 0);
+ ew32(TCTL, E1000_TCTL_PSP);
+ e1e_flush();
+
+ msleep(10);
+
+ /* Workaround for ICH8 bit corruption issue in FIFO memory */
+ if (hw->mac.type == e1000_ich8lan) {
+ /* Set Tx and Rx buffer allocation to 8k apiece. */
+ ew32(PBA, E1000_PBA_8K);
+ /* Set Packet Buffer Size to 16k. */
+ ew32(PBS, E1000_PBS_16K);
+ }
+
+ ctrl = er32(CTRL);
+
+ if (!e1000_check_reset_block(hw)) {
+ /*
+ * PHY HW reset requires MAC CORE reset at the same
+ * time to make sure the interface between MAC and the
+ * external PHY is reset.
+ */
+ ctrl |= E1000_CTRL_PHY_RST;
+ }
+ ret_val = e1000_acquire_swflag_ich8lan(hw);
+ hw_dbg(hw, "Issuing a global reset to ich8lan");
+ ew32(CTRL, (ctrl | E1000_CTRL_RST));
+ msleep(20);
+
+ ret_val = e1000e_get_auto_rd_done(hw);
+ if (ret_val) {
+ /*
+ * When auto config read does not complete, do not
+ * return with an error. This can happen in situations
+ * where there is no eeprom and prevents getting link.
+ */
+ hw_dbg(hw, "Auto Read Done did not complete\n");
+ }
+
+ ew32(IMC, 0xffffffff);
+ icr = er32(ICR);
+
+ kab = er32(KABGTXD);
+ kab |= E1000_KABGTXD_BGSQLBIAS;
+ ew32(KABGTXD, kab);
+
+ return ret_val;
+}
+
+/**
+ * e1000_init_hw_ich8lan - Initialize the hardware
+ * @hw: pointer to the HW structure
+ *
+ * Prepares the hardware for transmit and receive by doing the following:
+ * - initialize hardware bits
+ * - initialize LED identification
+ * - setup receive address registers
+ * - setup flow control
+ * - setup transmit descriptors
+ * - clear statistics
+ **/
+static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 ctrl_ext, txdctl, snoop;
+ s32 ret_val;
+ u16 i;
+
+ e1000_initialize_hw_bits_ich8lan(hw);
+
+ /* Initialize identification LED */
+ ret_val = e1000e_id_led_init(hw);
+ if (ret_val) {
+ hw_dbg(hw, "Error initializing identification LED\n");
+ return ret_val;
+ }
+
+ /* Setup the receive address. */
+ e1000e_init_rx_addrs(hw, mac->rar_entry_count);
+
+ /* Zero out the Multicast HASH table */
+ hw_dbg(hw, "Zeroing the MTA\n");
+ for (i = 0; i < mac->mta_reg_count; i++)
+ E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);
+
+ /* Setup link and flow control */
+ ret_val = e1000_setup_link_ich8lan(hw);
+
+ /* Set the transmit descriptor write-back policy for both queues */
+ txdctl = er32(TXDCTL(0));
+ txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB;
+ txdctl = (txdctl & ~E1000_TXDCTL_PTHRESH) |
+ E1000_TXDCTL_MAX_TX_DESC_PREFETCH;
+ ew32(TXDCTL(0), txdctl);
+ txdctl = er32(TXDCTL(1));
+ txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB;
+ txdctl = (txdctl & ~E1000_TXDCTL_PTHRESH) |
+ E1000_TXDCTL_MAX_TX_DESC_PREFETCH;
+ ew32(TXDCTL(1), txdctl);
+
+ /*
+ * ICH8 has opposite polarity of no_snoop bits.
+ * By default, we should use snoop behavior.
+ */
+ if (mac->type == e1000_ich8lan)
+ snoop = PCIE_ICH8_SNOOP_ALL;
+ else
+ snoop = (u32) ~(PCIE_NO_SNOOP_ALL);
+ e1000e_set_pcie_no_snoop(hw, snoop);
+
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
+ ew32(CTRL_EXT, ctrl_ext);
+
+ /*
+ * Clear all of the statistics registers (clear on read). It is
+ * important that we do this after we have tried to establish link
+ * because the symbol error count will increment wildly if there
+ * is no link.
+ */
+ e1000_clear_hw_cntrs_ich8lan(hw);
+
+ return 0;
+}
+/**
+ * e1000_initialize_hw_bits_ich8lan - Initialize required hardware bits
+ * @hw: pointer to the HW structure
+ *
+ * Sets/Clears required hardware bits necessary for correctly setting up the
+ * hardware for transmit and receive.
+ **/
+static void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw)
+{
+ u32 reg;
+
+ /* Extended Device Control */
+ reg = er32(CTRL_EXT);
+ reg |= (1 << 22);
+ ew32(CTRL_EXT, reg);
+
+ /* Transmit Descriptor Control 0 */
+ reg = er32(TXDCTL(0));
+ reg |= (1 << 22);
+ ew32(TXDCTL(0), reg);
+
+ /* Transmit Descriptor Control 1 */
+ reg = er32(TXDCTL(1));
+ reg |= (1 << 22);
+ ew32(TXDCTL(1), reg);
+
+ /* Transmit Arbitration Control 0 */
+ reg = er32(TARC(0));
+ if (hw->mac.type == e1000_ich8lan)
+ reg |= (1 << 28) | (1 << 29);
+ reg |= (1 << 23) | (1 << 24) | (1 << 26) | (1 << 27);
+ ew32(TARC(0), reg);
+
+ /* Transmit Arbitration Control 1 */
+ reg = er32(TARC(1));
+ if (er32(TCTL) & E1000_TCTL_MULR)
+ reg &= ~(1 << 28);
+ else
+ reg |= (1 << 28);
+ reg |= (1 << 24) | (1 << 26) | (1 << 30);
+ ew32(TARC(1), reg);
+
+ /* Device Status */
+ if (hw->mac.type == e1000_ich8lan) {
+ reg = er32(STATUS);
+ reg &= ~(1 << 31);
+ ew32(STATUS, reg);
+ }
+}
+
+/**
+ * e1000_setup_link_ich8lan - Setup flow control and link settings
+ * @hw: pointer to the HW structure
+ *
+ * Determines which flow control settings to use, then configures flow
+ * control. Calls the appropriate media-specific link configuration
+ * function. Assuming the adapter has a valid link partner, a valid link
+ * should be established. Assumes the hardware has previously been reset
+ * and the transmitter and receiver are not enabled.
+ **/
+static s32 e1000_setup_link_ich8lan(struct e1000_hw *hw)
+{
+ s32 ret_val;
+
+ if (e1000_check_reset_block(hw))
+ return 0;
+
+ /*
+ * ICH parts do not have a word in the NVM to determine
+ * the default flow control setting, so we explicitly
+ * set it to full.
+ */
+ if (hw->fc.type == e1000_fc_default)
+ hw->fc.type = e1000_fc_full;
+
+ hw->fc.original_type = hw->fc.type;
+
+ hw_dbg(hw, "After fix-ups FlowControl is now = %x\n", hw->fc.type);
+
+ /* Continue to configure the copper link. */
+ ret_val = e1000_setup_copper_link_ich8lan(hw);
+ if (ret_val)
+ return ret_val;
+
+ ew32(FCTTV, hw->fc.pause_time);
+
+ return e1000e_set_fc_watermarks(hw);
+}
+
+/**
+ * e1000_setup_copper_link_ich8lan - Configure MAC/PHY interface
+ * @hw: pointer to the HW structure
+ *
+ * Configures the kumeran interface to the PHY to wait the appropriate time
+ * when polling the PHY, then call the generic setup_copper_link to finish
+ * configuring the copper link.
+ **/
+static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val;
+ u16 reg_data;
+
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_SLU;
+ ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ew32(CTRL, ctrl);
+
+ /*
+ * Set the mac to wait the maximum time between each iteration
+ * and increase the max iterations when polling the phy;
+ * this fixes erroneous timeouts at 10Mbps.
+ */
+ ret_val = e1000e_write_kmrn_reg(hw, GG82563_REG(0x34, 4), 0xFFFF);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000e_read_kmrn_reg(hw, GG82563_REG(0x34, 9), ®_data);
+ if (ret_val)
+ return ret_val;
+ reg_data |= 0x3F;
+ ret_val = e1000e_write_kmrn_reg(hw, GG82563_REG(0x34, 9), reg_data);
+ if (ret_val)
+ return ret_val;
+
+ if (hw->phy.type == e1000_phy_igp_3) {
+ ret_val = e1000e_copper_link_setup_igp(hw);
+ if (ret_val)
+ return ret_val;
+ } else if (hw->phy.type == e1000_phy_bm) {
+ ret_val = e1000e_copper_link_setup_m88(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ if (hw->phy.type == e1000_phy_ife) {
+ ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, ®_data);
+ if (ret_val)
+ return ret_val;
+
+ reg_data &= ~IFE_PMC_AUTO_MDIX;
+
+ switch (hw->phy.mdix) {
+ case 1:
+ reg_data &= ~IFE_PMC_FORCE_MDIX;
+ break;
+ case 2:
+ reg_data |= IFE_PMC_FORCE_MDIX;
+ break;
+ case 0:
+ default:
+ reg_data |= IFE_PMC_AUTO_MDIX;
+ break;
+ }
+ ret_val = e1e_wphy(hw, IFE_PHY_MDIX_CONTROL, reg_data);
+ if (ret_val)
+ return ret_val;
+ }
+ return e1000e_setup_copper_link(hw);
+}
+
+/**
+ * e1000_get_link_up_info_ich8lan - Get current link speed and duplex
+ * @hw: pointer to the HW structure
+ * @speed: pointer to store current link speed
+ * @duplex: pointer to store the current link duplex
+ *
+ * Calls the generic get_speed_and_duplex to retrieve the current link
+ * information and then calls the Kumeran lock loss workaround for links at
+ * gigabit speeds.
+ **/
+static s32 e1000_get_link_up_info_ich8lan(struct e1000_hw *hw, u16 *speed,
+ u16 *duplex)
+{
+ s32 ret_val;
+
+ ret_val = e1000e_get_speed_and_duplex_copper(hw, speed, duplex);
+ if (ret_val)
+ return ret_val;
+
+ if ((hw->mac.type == e1000_ich8lan) &&
+ (hw->phy.type == e1000_phy_igp_3) &&
+ (*speed == SPEED_1000)) {
+ ret_val = e1000_kmrn_lock_loss_workaround_ich8lan(hw);
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000_kmrn_lock_loss_workaround_ich8lan - Kumeran workaround
+ * @hw: pointer to the HW structure
+ *
+ * Work-around for 82566 Kumeran PCS lock loss:
+ * On link status change (i.e. PCI reset, speed change) and link is up and
+ * speed is gigabit-
+ * 0) if workaround is optionally disabled do nothing
+ * 1) wait 1ms for Kumeran link to come up
+ * 2) check Kumeran Diagnostic register PCS lock loss bit
+ * 3) if not set the link is locked (all is good), otherwise...
+ * 4) reset the PHY
+ * 5) repeat up to 10 times
+ * Note: this is only called for IGP3 copper when speed is 1gb.
+ **/
+static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
+ u32 phy_ctrl;
+ s32 ret_val;
+ u16 i, data;
+ bool link;
+
+ if (!dev_spec->kmrn_lock_loss_workaround_enabled)
+ return 0;
+
+ /*
+ * Make sure link is up before proceeding. If not just return.
+ * Attempting this while link is negotiating fouled up link
+ * stability
+ */
+ ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
+ if (!link)
+ return 0;
+
+ for (i = 0; i < 10; i++) {
+ /* read once to clear */
+ ret_val = e1e_rphy(hw, IGP3_KMRN_DIAG, &data);
+ if (ret_val)
+ return ret_val;
+ /* and again to get new status */
+ ret_val = e1e_rphy(hw, IGP3_KMRN_DIAG, &data);
+ if (ret_val)
+ return ret_val;
+
+ /* check for PCS lock */
+ if (!(data & IGP3_KMRN_DIAG_PCS_LOCK_LOSS))
+ return 0;
+
+ /* Issue PHY reset */
+ e1000_phy_hw_reset(hw);
+ mdelay(5);
+ }
+ /* Disable GigE link negotiation */
+ phy_ctrl = er32(PHY_CTRL);
+ phy_ctrl |= (E1000_PHY_CTRL_GBE_DISABLE |
+ E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
+ ew32(PHY_CTRL, phy_ctrl);
+
+ /*
+ * Call gig speed drop workaround on Gig disable before accessing
+ * any PHY registers
+ */
+ e1000e_gig_downshift_workaround_ich8lan(hw);
+
+ /* unable to acquire PCS lock */
+ return -E1000_ERR_PHY;
+}
+
+/**
+ * e1000_set_kmrn_lock_loss_workaround_ich8lan - Set Kumeran workaround state
+ * @hw: pointer to the HW structure
+ * @state: boolean value used to set the current Kumeran workaround state
+ *
+ * If ICH8, set the current Kumeran workaround state (enabled - TRUE
+ * /disabled - FALSE).
+ **/
+void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw,
+ bool state)
+{
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
+
+ if (hw->mac.type != e1000_ich8lan) {
+ hw_dbg(hw, "Workaround applies to ICH8 only.\n");
+ return;
+ }
+
+ dev_spec->kmrn_lock_loss_workaround_enabled = state;
+}
+
+/**
+ * e1000_ipg3_phy_powerdown_workaround_ich8lan - Power down workaround on D3
+ * @hw: pointer to the HW structure
+ *
+ * Workaround for 82566 power-down on D3 entry:
+ * 1) disable gigabit link
+ * 2) write VR power-down enable
+ * 3) read it back
+ * Continue if successful, else issue LCD reset and repeat
+ **/
+void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw)
+{
+ u32 reg;
+ u16 data;
+ u8 retry = 0;
+
+ if (hw->phy.type != e1000_phy_igp_3)
+ return;
+
+ /* Try the workaround twice (if needed) */
+ do {
+ /* Disable link */
+ reg = er32(PHY_CTRL);
+ reg |= (E1000_PHY_CTRL_GBE_DISABLE |
+ E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
+ ew32(PHY_CTRL, reg);
+
+ /*
+ * Call gig speed drop workaround on Gig disable before
+ * accessing any PHY registers
+ */
+ if (hw->mac.type == e1000_ich8lan)
+ e1000e_gig_downshift_workaround_ich8lan(hw);
+
+ /* Write VR power-down enable */
+ e1e_rphy(hw, IGP3_VR_CTRL, &data);
+ data &= ~IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK;
+ e1e_wphy(hw, IGP3_VR_CTRL, data | IGP3_VR_CTRL_MODE_SHUTDOWN);
+
+ /* Read it back and test */
+ e1e_rphy(hw, IGP3_VR_CTRL, &data);
+ data &= IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK;
+ if ((data == IGP3_VR_CTRL_MODE_SHUTDOWN) || retry)
+ break;
+
+ /* Issue PHY reset and repeat at most one more time */
+ reg = er32(CTRL);
+ ew32(CTRL, reg | E1000_CTRL_PHY_RST);
+ retry++;
+ } while (retry);
+}
+
+/**
+ * e1000e_gig_downshift_workaround_ich8lan - WoL from S5 stops working
+ * @hw: pointer to the HW structure
+ *
+ * Steps to take when dropping from 1Gb/s (eg. link cable removal (LSC),
+ * LPLU, Gig disable, MDIC PHY reset):
+ * 1) Set Kumeran Near-end loopback
+ * 2) Clear Kumeran Near-end loopback
+ * Should only be called for ICH8[m] devices with IGP_3 Phy.
+ **/
+void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 reg_data;
+
+ if ((hw->mac.type != e1000_ich8lan) ||
+ (hw->phy.type != e1000_phy_igp_3))
+ return;
+
+ ret_val = e1000e_read_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET,
+ ®_data);
+ if (ret_val)
+ return;
+ reg_data |= E1000_KMRNCTRLSTA_DIAG_NELPBK;
+ ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET,
+ reg_data);
+ if (ret_val)
+ return;
+ reg_data &= ~E1000_KMRNCTRLSTA_DIAG_NELPBK;
+ ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET,
+ reg_data);
+}
+
+/**
+ * e1000e_disable_gig_wol_ich8lan - disable gig during WoL
+ * @hw: pointer to the HW structure
+ *
+ * During S0 to Sx transition, it is possible the link remains at gig
+ * instead of negotiating to a lower speed. Before going to Sx, set
+ * 'LPLU Enabled' and 'Gig Disable' to force link speed negotiation
+ * to a lower speed.
+ *
+ * Should only be called for ICH9 and ICH10 devices.
+ **/
+void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw)
+{
+ u32 phy_ctrl;
+
+ if ((hw->mac.type == e1000_ich10lan) ||
+ (hw->mac.type == e1000_ich9lan)) {
+ phy_ctrl = er32(PHY_CTRL);
+ phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU |
+ E1000_PHY_CTRL_GBE_DISABLE;
+ ew32(PHY_CTRL, phy_ctrl);
+ }
+
+ return;
+}
+
+/**
+ * e1000_cleanup_led_ich8lan - Restore the default LED operation
+ * @hw: pointer to the HW structure
+ *
+ * Return the LED back to the default configuration.
+ **/
+static s32 e1000_cleanup_led_ich8lan(struct e1000_hw *hw)
+{
+ if (hw->phy.type == e1000_phy_ife)
+ return e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED, 0);
+
+ ew32(LEDCTL, hw->mac.ledctl_default);
+ return 0;
+}
+
+/**
+ * e1000_led_on_ich8lan - Turn LEDs on
+ * @hw: pointer to the HW structure
+ *
+ * Turn on the LEDs.
+ **/
+static s32 e1000_led_on_ich8lan(struct e1000_hw *hw)
+{
+ if (hw->phy.type == e1000_phy_ife)
+ return e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED,
+ (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_ON));
+
+ ew32(LEDCTL, hw->mac.ledctl_mode2);
+ return 0;
+}
+
+/**
+ * e1000_led_off_ich8lan - Turn LEDs off
+ * @hw: pointer to the HW structure
+ *
+ * Turn off the LEDs.
+ **/
+static s32 e1000_led_off_ich8lan(struct e1000_hw *hw)
+{
+ if (hw->phy.type == e1000_phy_ife)
+ return e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED,
+ (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_OFF));
+
+ ew32(LEDCTL, hw->mac.ledctl_mode1);
+ return 0;
+}
+
+/**
+ * e1000_get_cfg_done_ich8lan - Read config done bit
+ * @hw: pointer to the HW structure
+ *
+ * Read the management control register for the config done bit for
+ * completion status. NOTE: silicon which is EEPROM-less will fail trying
+ * to read the config done bit, so an error is *ONLY* logged and returns
+ * E1000_SUCCESS. If we were to return with error, EEPROM-less silicon
+ * would not be able to be reset or change link.
+ **/
+static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw)
+{
+ u32 bank = 0;
+
+ e1000e_get_cfg_done(hw);
+
+ /* If EEPROM is not marked present, init the IGP 3 PHY manually */
+ if (hw->mac.type != e1000_ich10lan) {
+ if (((er32(EECD) & E1000_EECD_PRES) == 0) &&
+ (hw->phy.type == e1000_phy_igp_3)) {
+ e1000e_phy_init_script_igp3(hw);
+ }
+ } else {
+ if (e1000_valid_nvm_bank_detect_ich8lan(hw, &bank)) {
+ /* Maybe we should do a basic PHY config */
+ hw_dbg(hw, "EEPROM not present\n");
+ return -E1000_ERR_CONFIG;
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_clear_hw_cntrs_ich8lan - Clear statistical counters
+ * @hw: pointer to the HW structure
+ *
+ * Clears hardware counters specific to the silicon family and calls
+ * clear_hw_cntrs_generic to clear all general purpose counters.
+ **/
+static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw)
+{
+ u32 temp;
+
+ e1000e_clear_hw_cntrs_base(hw);
+
+ temp = er32(ALGNERRC);
+ temp = er32(RXERRC);
+ temp = er32(TNCRS);
+ temp = er32(CEXTERR);
+ temp = er32(TSCTC);
+ temp = er32(TSCTFC);
+
+ temp = er32(MGTPRC);
+ temp = er32(MGTPDC);
+ temp = er32(MGTPTC);
+
+ temp = er32(IAC);
+ temp = er32(ICRXOC);
+
+}
+
+static struct e1000_mac_operations ich8_mac_ops = {
+ .check_mng_mode = e1000_check_mng_mode_ich8lan,
+ .check_for_link = e1000e_check_for_copper_link,
+ .cleanup_led = e1000_cleanup_led_ich8lan,
+ .clear_hw_cntrs = e1000_clear_hw_cntrs_ich8lan,
+ .get_bus_info = e1000_get_bus_info_ich8lan,
+ .get_link_up_info = e1000_get_link_up_info_ich8lan,
+ .led_on = e1000_led_on_ich8lan,
+ .led_off = e1000_led_off_ich8lan,
+ .update_mc_addr_list = e1000e_update_mc_addr_list_generic,
+ .reset_hw = e1000_reset_hw_ich8lan,
+ .init_hw = e1000_init_hw_ich8lan,
+ .setup_link = e1000_setup_link_ich8lan,
+ .setup_physical_interface= e1000_setup_copper_link_ich8lan,
+};
+
+static struct e1000_phy_operations ich8_phy_ops = {
+ .acquire_phy = e1000_acquire_swflag_ich8lan,
+ .check_reset_block = e1000_check_reset_block_ich8lan,
+ .commit_phy = NULL,
+ .force_speed_duplex = e1000_phy_force_speed_duplex_ich8lan,
+ .get_cfg_done = e1000_get_cfg_done_ich8lan,
+ .get_cable_length = e1000e_get_cable_length_igp_2,
+ .get_phy_info = e1000_get_phy_info_ich8lan,
+ .read_phy_reg = e1000e_read_phy_reg_igp,
+ .release_phy = e1000_release_swflag_ich8lan,
+ .reset_phy = e1000_phy_hw_reset_ich8lan,
+ .set_d0_lplu_state = e1000_set_d0_lplu_state_ich8lan,
+ .set_d3_lplu_state = e1000_set_d3_lplu_state_ich8lan,
+ .write_phy_reg = e1000e_write_phy_reg_igp,
+};
+
+static struct e1000_nvm_operations ich8_nvm_ops = {
+ .acquire_nvm = e1000_acquire_swflag_ich8lan,
+ .read_nvm = e1000_read_nvm_ich8lan,
+ .release_nvm = e1000_release_swflag_ich8lan,
+ .update_nvm = e1000_update_nvm_checksum_ich8lan,
+ .valid_led_default = e1000_valid_led_default_ich8lan,
+ .validate_nvm = e1000_validate_nvm_checksum_ich8lan,
+ .write_nvm = e1000_write_nvm_ich8lan,
+};
+
+struct e1000_info e1000_ich8_info = {
+ .mac = e1000_ich8lan,
+ .flags = FLAG_HAS_WOL
+ | FLAG_IS_ICH
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_CTRLEXT_ON_LOAD
+ | FLAG_HAS_AMT
+ | FLAG_HAS_FLASH
+ | FLAG_APME_IN_WUC,
+ .pba = 8,
+ .get_variants = e1000_get_variants_ich8lan,
+ .mac_ops = &ich8_mac_ops,
+ .phy_ops = &ich8_phy_ops,
+ .nvm_ops = &ich8_nvm_ops,
+};
+
+struct e1000_info e1000_ich9_info = {
+ .mac = e1000_ich9lan,
+ .flags = FLAG_HAS_JUMBO_FRAMES
+ | FLAG_IS_ICH
+ | FLAG_HAS_WOL
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_CTRLEXT_ON_LOAD
+ | FLAG_HAS_AMT
+ | FLAG_HAS_ERT
+ | FLAG_HAS_FLASH
+ | FLAG_APME_IN_WUC,
+ .pba = 10,
+ .get_variants = e1000_get_variants_ich8lan,
+ .mac_ops = &ich8_mac_ops,
+ .phy_ops = &ich8_phy_ops,
+ .nvm_ops = &ich8_nvm_ops,
+};
+
+struct e1000_info e1000_ich10_info = {
+ .mac = e1000_ich10lan,
+ .flags = FLAG_HAS_JUMBO_FRAMES
+ | FLAG_IS_ICH
+ | FLAG_HAS_WOL
+ | FLAG_RX_CSUM_ENABLED
+ | FLAG_HAS_CTRLEXT_ON_LOAD
+ | FLAG_HAS_AMT
+ | FLAG_HAS_ERT
+ | FLAG_HAS_FLASH
+ | FLAG_APME_IN_WUC,
+ .pba = 10,
+ .get_variants = e1000_get_variants_ich8lan,
+ .mac_ops = &ich8_mac_ops,
+ .phy_ops = &ich8_phy_ops,
+ .nvm_ops = &ich8_nvm_ops,
+};
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2008 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#include <linux/netdevice.h>
+#include <linux/ethtool.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+
+#include "e1000.h"
+
+enum e1000_mng_mode {
+ e1000_mng_mode_none = 0,
+ e1000_mng_mode_asf,
+ e1000_mng_mode_pt,
+ e1000_mng_mode_ipmi,
+ e1000_mng_mode_host_if_only
+};
+
+#define E1000_FACTPS_MNGCG 0x20000000
+
+/* Intel(R) Active Management Technology signature */
+#define E1000_IAMT_SIGNATURE 0x544D4149
+
+/**
+ * e1000e_get_bus_info_pcie - Get PCIe bus information
+ * @hw: pointer to the HW structure
+ *
+ * Determines and stores the system bus information for a particular
+ * network interface. The following bus information is determined and stored:
+ * bus speed, bus width, type (PCIe), and PCIe function.
+ **/
+s32 e1000e_get_bus_info_pcie(struct e1000_hw *hw)
+{
+ struct e1000_bus_info *bus = &hw->bus;
+ struct e1000_adapter *adapter = hw->adapter;
+ u32 status;
+ u16 pcie_link_status, pci_header_type, cap_offset;
+
+ cap_offset = pci_find_capability(adapter->pdev, PCI_CAP_ID_EXP);
+ if (!cap_offset) {
+ bus->width = e1000_bus_width_unknown;
+ } else {
+ pci_read_config_word(adapter->pdev,
+ cap_offset + PCIE_LINK_STATUS,
+ &pcie_link_status);
+ bus->width = (enum e1000_bus_width)((pcie_link_status &
+ PCIE_LINK_WIDTH_MASK) >>
+ PCIE_LINK_WIDTH_SHIFT);
+ }
+
+ pci_read_config_word(adapter->pdev, PCI_HEADER_TYPE_REGISTER,
+ &pci_header_type);
+ if (pci_header_type & PCI_HEADER_TYPE_MULTIFUNC) {
+ status = er32(STATUS);
+ bus->func = (status & E1000_STATUS_FUNC_MASK)
+ >> E1000_STATUS_FUNC_SHIFT;
+ } else {
+ bus->func = 0;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_write_vfta - Write value to VLAN filter table
+ * @hw: pointer to the HW structure
+ * @offset: register offset in VLAN filter table
+ * @value: register value written to VLAN filter table
+ *
+ * Writes value at the given offset in the register array which stores
+ * the VLAN filter table.
+ **/
+void e1000e_write_vfta(struct e1000_hw *hw, u32 offset, u32 value)
+{
+ E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, value);
+ e1e_flush();
+}
+
+/**
+ * e1000e_init_rx_addrs - Initialize receive address's
+ * @hw: pointer to the HW structure
+ * @rar_count: receive address registers
+ *
+ * Setups the receive address registers by setting the base receive address
+ * register to the devices MAC address and clearing all the other receive
+ * address registers to 0.
+ **/
+void e1000e_init_rx_addrs(struct e1000_hw *hw, u16 rar_count)
+{
+ u32 i;
+
+ /* Setup the receive address */
+ hw_dbg(hw, "Programming MAC Address into RAR[0]\n");
+
+ e1000e_rar_set(hw, hw->mac.addr, 0);
+
+ /* Zero out the other (rar_entry_count - 1) receive addresses */
+ hw_dbg(hw, "Clearing RAR[1-%u]\n", rar_count-1);
+ for (i = 1; i < rar_count; i++) {
+ E1000_WRITE_REG_ARRAY(hw, E1000_RA, (i << 1), 0);
+ e1e_flush();
+ E1000_WRITE_REG_ARRAY(hw, E1000_RA, ((i << 1) + 1), 0);
+ e1e_flush();
+ }
+}
+
+/**
+ * e1000e_rar_set - Set receive address register
+ * @hw: pointer to the HW structure
+ * @addr: pointer to the receive address
+ * @index: receive address array register
+ *
+ * Sets the receive address array register at index to the address passed
+ * in by addr.
+ **/
+void e1000e_rar_set(struct e1000_hw *hw, u8 *addr, u32 index)
+{
+ u32 rar_low, rar_high;
+
+ /*
+ * HW expects these in little endian so we reverse the byte order
+ * from network order (big endian) to little endian
+ */
+ rar_low = ((u32) addr[0] |
+ ((u32) addr[1] << 8) |
+ ((u32) addr[2] << 16) | ((u32) addr[3] << 24));
+
+ rar_high = ((u32) addr[4] | ((u32) addr[5] << 8));
+
+ rar_high |= E1000_RAH_AV;
+
+ E1000_WRITE_REG_ARRAY(hw, E1000_RA, (index << 1), rar_low);
+ E1000_WRITE_REG_ARRAY(hw, E1000_RA, ((index << 1) + 1), rar_high);
+}
+
+/**
+ * e1000_mta_set - Set multicast filter table address
+ * @hw: pointer to the HW structure
+ * @hash_value: determines the MTA register and bit to set
+ *
+ * The multicast table address is a register array of 32-bit registers.
+ * The hash_value is used to determine what register the bit is in, the
+ * current value is read, the new bit is OR'd in and the new value is
+ * written back into the register.
+ **/
+static void e1000_mta_set(struct e1000_hw *hw, u32 hash_value)
+{
+ u32 hash_bit, hash_reg, mta;
+
+ /*
+ * The MTA is a register array of 32-bit registers. It is
+ * treated like an array of (32*mta_reg_count) bits. We want to
+ * set bit BitArray[hash_value]. So we figure out what register
+ * the bit is in, read it, OR in the new bit, then write
+ * back the new value. The (hw->mac.mta_reg_count - 1) serves as a
+ * mask to bits 31:5 of the hash value which gives us the
+ * register we're modifying. The hash bit within that register
+ * is determined by the lower 5 bits of the hash value.
+ */
+ hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1);
+ hash_bit = hash_value & 0x1F;
+
+ mta = E1000_READ_REG_ARRAY(hw, E1000_MTA, hash_reg);
+
+ mta |= (1 << hash_bit);
+
+ E1000_WRITE_REG_ARRAY(hw, E1000_MTA, hash_reg, mta);
+ e1e_flush();
+}
+
+/**
+ * e1000_hash_mc_addr - Generate a multicast hash value
+ * @hw: pointer to the HW structure
+ * @mc_addr: pointer to a multicast address
+ *
+ * Generates a multicast address hash value which is used to determine
+ * the multicast filter table array address and new table value. See
+ * e1000_mta_set_generic()
+ **/
+static u32 e1000_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr)
+{
+ u32 hash_value, hash_mask;
+ u8 bit_shift = 0;
+
+ /* Register count multiplied by bits per register */
+ hash_mask = (hw->mac.mta_reg_count * 32) - 1;
+
+ /*
+ * For a mc_filter_type of 0, bit_shift is the number of left-shifts
+ * where 0xFF would still fall within the hash mask.
+ */
+ while (hash_mask >> bit_shift != 0xFF)
+ bit_shift++;
+
+ /*
+ * The portion of the address that is used for the hash table
+ * is determined by the mc_filter_type setting.
+ * The algorithm is such that there is a total of 8 bits of shifting.
+ * The bit_shift for a mc_filter_type of 0 represents the number of
+ * left-shifts where the MSB of mc_addr[5] would still fall within
+ * the hash_mask. Case 0 does this exactly. Since there are a total
+ * of 8 bits of shifting, then mc_addr[4] will shift right the
+ * remaining number of bits. Thus 8 - bit_shift. The rest of the
+ * cases are a variation of this algorithm...essentially raising the
+ * number of bits to shift mc_addr[5] left, while still keeping the
+ * 8-bit shifting total.
+ *
+ * For example, given the following Destination MAC Address and an
+ * mta register count of 128 (thus a 4096-bit vector and 0xFFF mask),
+ * we can see that the bit_shift for case 0 is 4. These are the hash
+ * values resulting from each mc_filter_type...
+ * [0] [1] [2] [3] [4] [5]
+ * 01 AA 00 12 34 56
+ * LSB MSB
+ *
+ * case 0: hash_value = ((0x34 >> 4) | (0x56 << 4)) & 0xFFF = 0x563
+ * case 1: hash_value = ((0x34 >> 3) | (0x56 << 5)) & 0xFFF = 0xAC6
+ * case 2: hash_value = ((0x34 >> 2) | (0x56 << 6)) & 0xFFF = 0x163
+ * case 3: hash_value = ((0x34 >> 0) | (0x56 << 8)) & 0xFFF = 0x634
+ */
+ switch (hw->mac.mc_filter_type) {
+ default:
+ case 0:
+ break;
+ case 1:
+ bit_shift += 1;
+ break;
+ case 2:
+ bit_shift += 2;
+ break;
+ case 3:
+ bit_shift += 4;
+ break;
+ }
+
+ hash_value = hash_mask & (((mc_addr[4] >> (8 - bit_shift)) |
+ (((u16) mc_addr[5]) << bit_shift)));
+
+ return hash_value;
+}
+
+/**
+ * e1000e_update_mc_addr_list_generic - Update Multicast addresses
+ * @hw: pointer to the HW structure
+ * @mc_addr_list: array of multicast addresses to program
+ * @mc_addr_count: number of multicast addresses to program
+ * @rar_used_count: the first RAR register free to program
+ * @rar_count: total number of supported Receive Address Registers
+ *
+ * Updates the Receive Address Registers and Multicast Table Array.
+ * The caller must have a packed mc_addr_list of multicast addresses.
+ * The parameter rar_count will usually be hw->mac.rar_entry_count
+ * unless there are workarounds that change this.
+ **/
+void e1000e_update_mc_addr_list_generic(struct e1000_hw *hw,
+ u8 *mc_addr_list, u32 mc_addr_count,
+ u32 rar_used_count, u32 rar_count)
+{
+ u32 hash_value;
+ u32 i;
+
+ /*
+ * Load the first set of multicast addresses into the exact
+ * filters (RAR). If there are not enough to fill the RAR
+ * array, clear the filters.
+ */
+ for (i = rar_used_count; i < rar_count; i++) {
+ if (mc_addr_count) {
+ e1000e_rar_set(hw, mc_addr_list, i);
+ mc_addr_count--;
+ mc_addr_list += ETH_ALEN;
+ } else {
+ E1000_WRITE_REG_ARRAY(hw, E1000_RA, i << 1, 0);
+ e1e_flush();
+ E1000_WRITE_REG_ARRAY(hw, E1000_RA, (i << 1) + 1, 0);
+ e1e_flush();
+ }
+ }
+
+ /* Clear the old settings from the MTA */
+ hw_dbg(hw, "Clearing MTA\n");
+ for (i = 0; i < hw->mac.mta_reg_count; i++) {
+ E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);
+ e1e_flush();
+ }
+
+ /* Load any remaining multicast addresses into the hash table. */
+ for (; mc_addr_count > 0; mc_addr_count--) {
+ hash_value = e1000_hash_mc_addr(hw, mc_addr_list);
+ hw_dbg(hw, "Hash value = 0x%03X\n", hash_value);
+ e1000_mta_set(hw, hash_value);
+ mc_addr_list += ETH_ALEN;
+ }
+}
+
+/**
+ * e1000e_clear_hw_cntrs_base - Clear base hardware counters
+ * @hw: pointer to the HW structure
+ *
+ * Clears the base hardware counters by reading the counter registers.
+ **/
+void e1000e_clear_hw_cntrs_base(struct e1000_hw *hw)
+{
+ u32 temp;
+
+ temp = er32(CRCERRS);
+ temp = er32(SYMERRS);
+ temp = er32(MPC);
+ temp = er32(SCC);
+ temp = er32(ECOL);
+ temp = er32(MCC);
+ temp = er32(LATECOL);
+ temp = er32(COLC);
+ temp = er32(DC);
+ temp = er32(SEC);
+ temp = er32(RLEC);
+ temp = er32(XONRXC);
+ temp = er32(XONTXC);
+ temp = er32(XOFFRXC);
+ temp = er32(XOFFTXC);
+ temp = er32(FCRUC);
+ temp = er32(GPRC);
+ temp = er32(BPRC);
+ temp = er32(MPRC);
+ temp = er32(GPTC);
+ temp = er32(GORCL);
+ temp = er32(GORCH);
+ temp = er32(GOTCL);
+ temp = er32(GOTCH);
+ temp = er32(RNBC);
+ temp = er32(RUC);
+ temp = er32(RFC);
+ temp = er32(ROC);
+ temp = er32(RJC);
+ temp = er32(TORL);
+ temp = er32(TORH);
+ temp = er32(TOTL);
+ temp = er32(TOTH);
+ temp = er32(TPR);
+ temp = er32(TPT);
+ temp = er32(MPTC);
+ temp = er32(BPTC);
+}
+
+/**
+ * e1000e_check_for_copper_link - Check for link (Copper)
+ * @hw: pointer to the HW structure
+ *
+ * Checks to see of the link status of the hardware has changed. If a
+ * change in link status has been detected, then we read the PHY registers
+ * to get the current speed/duplex if link exists.
+ **/
+s32 e1000e_check_for_copper_link(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val;
+ bool link;
+
+ /*
+ * We only want to go out to the PHY registers to see if Auto-Neg
+ * has completed and/or if our link status has changed. The
+ * get_link_status flag is set upon receiving a Link Status
+ * Change or Rx Sequence Error interrupt.
+ */
+ if (!mac->get_link_status)
+ return 0;
+
+ /*
+ * First we want to see if the MII Status Register reports
+ * link. If so, then we want to get the current speed/duplex
+ * of the PHY.
+ */
+ ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
+ if (ret_val)
+ return ret_val;
+
+ if (!link)
+ return ret_val; /* No link detected */
+
+ mac->get_link_status = 0;
+
+ /*
+ * Check if there was DownShift, must be checked
+ * immediately after link-up
+ */
+ e1000e_check_downshift(hw);
+
+ /*
+ * If we are forcing speed/duplex, then we simply return since
+ * we have already determined whether we have link or not.
+ */
+ if (!mac->autoneg) {
+ ret_val = -E1000_ERR_CONFIG;
+ return ret_val;
+ }
+
+ /*
+ * Auto-Neg is enabled. Auto Speed Detection takes care
+ * of MAC speed/duplex configuration. So we only need to
+ * configure Collision Distance in the MAC.
+ */
+ e1000e_config_collision_dist(hw);
+
+ /*
+ * Configure Flow Control now that Auto-Neg has completed.
+ * First, we need to restore the desired flow control
+ * settings because we may have had to re-autoneg with a
+ * different link partner.
+ */
+ ret_val = e1000e_config_fc_after_link_up(hw);
+ if (ret_val) {
+ hw_dbg(hw, "Error configuring flow control\n");
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000e_check_for_fiber_link - Check for link (Fiber)
+ * @hw: pointer to the HW structure
+ *
+ * Checks for link up on the hardware. If link is not up and we have
+ * a signal, then we need to force link up.
+ **/
+s32 e1000e_check_for_fiber_link(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 rxcw;
+ u32 ctrl;
+ u32 status;
+ s32 ret_val;
+
+ ctrl = er32(CTRL);
+ status = er32(STATUS);
+ rxcw = er32(RXCW);
+
+ /*
+ * If we don't have link (auto-negotiation failed or link partner
+ * cannot auto-negotiate), the cable is plugged in (we have signal),
+ * and our link partner is not trying to auto-negotiate with us (we
+ * are receiving idles or data), we need to force link up. We also
+ * need to give auto-negotiation time to complete, in case the cable
+ * was just plugged in. The autoneg_failed flag does this.
+ */
+ /* (ctrl & E1000_CTRL_SWDPIN1) == 1 == have signal */
+ if ((ctrl & E1000_CTRL_SWDPIN1) && (!(status & E1000_STATUS_LU)) &&
+ (!(rxcw & E1000_RXCW_C))) {
+ if (mac->autoneg_failed == 0) {
+ mac->autoneg_failed = 1;
+ return 0;
+ }
+ hw_dbg(hw, "NOT RXing /C/, disable AutoNeg and force link.\n");
+
+ /* Disable auto-negotiation in the TXCW register */
+ ew32(TXCW, (mac->txcw & ~E1000_TXCW_ANE));
+
+ /* Force link-up and also force full-duplex. */
+ ctrl = er32(CTRL);
+ ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
+ ew32(CTRL, ctrl);
+
+ /* Configure Flow Control after forcing link up. */
+ ret_val = e1000e_config_fc_after_link_up(hw);
+ if (ret_val) {
+ hw_dbg(hw, "Error configuring flow control\n");
+ return ret_val;
+ }
+ } else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
+ /*
+ * If we are forcing link and we are receiving /C/ ordered
+ * sets, re-enable auto-negotiation in the TXCW register
+ * and disable forced link in the Device Control register
+ * in an attempt to auto-negotiate with our link partner.
+ */
+ hw_dbg(hw, "RXing /C/, enable AutoNeg and stop forcing link.\n");
+ ew32(TXCW, mac->txcw);
+ ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
+
+ mac->serdes_has_link = 1;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_check_for_serdes_link - Check for link (Serdes)
+ * @hw: pointer to the HW structure
+ *
+ * Checks for link up on the hardware. If link is not up and we have
+ * a signal, then we need to force link up.
+ **/
+s32 e1000e_check_for_serdes_link(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 rxcw;
+ u32 ctrl;
+ u32 status;
+ s32 ret_val;
+
+ ctrl = er32(CTRL);
+ status = er32(STATUS);
+ rxcw = er32(RXCW);
+
+ /*
+ * If we don't have link (auto-negotiation failed or link partner
+ * cannot auto-negotiate), and our link partner is not trying to
+ * auto-negotiate with us (we are receiving idles or data),
+ * we need to force link up. We also need to give auto-negotiation
+ * time to complete.
+ */
+ /* (ctrl & E1000_CTRL_SWDPIN1) == 1 == have signal */
+ if ((!(status & E1000_STATUS_LU)) && (!(rxcw & E1000_RXCW_C))) {
+ if (mac->autoneg_failed == 0) {
+ mac->autoneg_failed = 1;
+ return 0;
+ }
+ hw_dbg(hw, "NOT RXing /C/, disable AutoNeg and force link.\n");
+
+ /* Disable auto-negotiation in the TXCW register */
+ ew32(TXCW, (mac->txcw & ~E1000_TXCW_ANE));
+
+ /* Force link-up and also force full-duplex. */
+ ctrl = er32(CTRL);
+ ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
+ ew32(CTRL, ctrl);
+
+ /* Configure Flow Control after forcing link up. */
+ ret_val = e1000e_config_fc_after_link_up(hw);
+ if (ret_val) {
+ hw_dbg(hw, "Error configuring flow control\n");
+ return ret_val;
+ }
+ } else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
+ /*
+ * If we are forcing link and we are receiving /C/ ordered
+ * sets, re-enable auto-negotiation in the TXCW register
+ * and disable forced link in the Device Control register
+ * in an attempt to auto-negotiate with our link partner.
+ */
+ hw_dbg(hw, "RXing /C/, enable AutoNeg and stop forcing link.\n");
+ ew32(TXCW, mac->txcw);
+ ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
+
+ mac->serdes_has_link = 1;
+ } else if (!(E1000_TXCW_ANE & er32(TXCW))) {
+ /*
+ * If we force link for non-auto-negotiation switch, check
+ * link status based on MAC synchronization for internal
+ * serdes media type.
+ */
+ /* SYNCH bit and IV bit are sticky. */
+ udelay(10);
+ if (E1000_RXCW_SYNCH & er32(RXCW)) {
+ if (!(rxcw & E1000_RXCW_IV)) {
+ mac->serdes_has_link = 1;
+ hw_dbg(hw, "SERDES: Link is up.\n");
+ }
+ } else {
+ mac->serdes_has_link = 0;
+ hw_dbg(hw, "SERDES: Link is down.\n");
+ }
+ }
+
+ if (E1000_TXCW_ANE & er32(TXCW)) {
+ status = er32(STATUS);
+ mac->serdes_has_link = (status & E1000_STATUS_LU);
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_set_default_fc_generic - Set flow control default values
+ * @hw: pointer to the HW structure
+ *
+ * Read the EEPROM for the default values for flow control and store the
+ * values.
+ **/
+static s32 e1000_set_default_fc_generic(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 nvm_data;
+
+ /*
+ * Read and store word 0x0F of the EEPROM. This word contains bits
+ * that determine the hardware's default PAUSE (flow control) mode,
+ * a bit that determines whether the HW defaults to enabling or
+ * disabling auto-negotiation, and the direction of the
+ * SW defined pins. If there is no SW over-ride of the flow
+ * control setting, then the variable hw->fc will
+ * be initialized based on a value in the EEPROM.
+ */
+ ret_val = e1000_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &nvm_data);
+
+ if (ret_val) {
+ hw_dbg(hw, "NVM Read Error\n");
+ return ret_val;
+ }
+
+ if ((nvm_data & NVM_WORD0F_PAUSE_MASK) == 0)
+ hw->fc.type = e1000_fc_none;
+ else if ((nvm_data & NVM_WORD0F_PAUSE_MASK) ==
+ NVM_WORD0F_ASM_DIR)
+ hw->fc.type = e1000_fc_tx_pause;
+ else
+ hw->fc.type = e1000_fc_full;
+
+ return 0;
+}
+
+/**
+ * e1000e_setup_link - Setup flow control and link settings
+ * @hw: pointer to the HW structure
+ *
+ * Determines which flow control settings to use, then configures flow
+ * control. Calls the appropriate media-specific link configuration
+ * function. Assuming the adapter has a valid link partner, a valid link
+ * should be established. Assumes the hardware has previously been reset
+ * and the transmitter and receiver are not enabled.
+ **/
+s32 e1000e_setup_link(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val;
+
+ /*
+ * In the case of the phy reset being blocked, we already have a link.
+ * We do not need to set it up again.
+ */
+ if (e1000_check_reset_block(hw))
+ return 0;
+
+ /*
+ * If flow control is set to default, set flow control based on
+ * the EEPROM flow control settings.
+ */
+ if (hw->fc.type == e1000_fc_default) {
+ ret_val = e1000_set_default_fc_generic(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /*
+ * We want to save off the original Flow Control configuration just
+ * in case we get disconnected and then reconnected into a different
+ * hub or switch with different Flow Control capabilities.
+ */
+ hw->fc.original_type = hw->fc.type;
+
+ hw_dbg(hw, "After fix-ups FlowControl is now = %x\n", hw->fc.type);
+
+ /* Call the necessary media_type subroutine to configure the link. */
+ ret_val = mac->ops.setup_physical_interface(hw);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Initialize the flow control address, type, and PAUSE timer
+ * registers to their default values. This is done even if flow
+ * control is disabled, because it does not hurt anything to
+ * initialize these registers.
+ */
+ hw_dbg(hw, "Initializing the Flow Control address, type and timer regs\n");
+ ew32(FCT, FLOW_CONTROL_TYPE);
+ ew32(FCAH, FLOW_CONTROL_ADDRESS_HIGH);
+ ew32(FCAL, FLOW_CONTROL_ADDRESS_LOW);
+
+ ew32(FCTTV, hw->fc.pause_time);
+
+ return e1000e_set_fc_watermarks(hw);
+}
+
+/**
+ * e1000_commit_fc_settings_generic - Configure flow control
+ * @hw: pointer to the HW structure
+ *
+ * Write the flow control settings to the Transmit Config Word Register (TXCW)
+ * base on the flow control settings in e1000_mac_info.
+ **/
+static s32 e1000_commit_fc_settings_generic(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 txcw;
+
+ /*
+ * Check for a software override of the flow control settings, and
+ * setup the device accordingly. If auto-negotiation is enabled, then
+ * software will have to set the "PAUSE" bits to the correct value in
+ * the Transmit Config Word Register (TXCW) and re-start auto-
+ * negotiation. However, if auto-negotiation is disabled, then
+ * software will have to manually configure the two flow control enable
+ * bits in the CTRL register.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames,
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but we
+ * do not support receiving pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) are enabled.
+ */
+ switch (hw->fc.type) {
+ case e1000_fc_none:
+ /* Flow control completely disabled by a software over-ride. */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD);
+ break;
+ case e1000_fc_rx_pause:
+ /*
+ * Rx Flow control is enabled and Tx Flow control is disabled
+ * by a software over-ride. Since there really isn't a way to
+ * advertise that we are capable of Rx Pause ONLY, we will
+ * advertise that we support both symmetric and asymmetric Rx
+ * PAUSE. Later, we will disable the adapter's ability to send
+ * PAUSE frames.
+ */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
+ break;
+ case e1000_fc_tx_pause:
+ /*
+ * Tx Flow control is enabled, and Rx Flow control is disabled,
+ * by a software over-ride.
+ */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR);
+ break;
+ case e1000_fc_full:
+ /*
+ * Flow control (both Rx and Tx) is enabled by a software
+ * over-ride.
+ */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
+ break;
+ default:
+ hw_dbg(hw, "Flow control param set incorrectly\n");
+ return -E1000_ERR_CONFIG;
+ break;
+ }
+
+ ew32(TXCW, txcw);
+ mac->txcw = txcw;
+
+ return 0;
+}
+
+/**
+ * e1000_poll_fiber_serdes_link_generic - Poll for link up
+ * @hw: pointer to the HW structure
+ *
+ * Polls for link up by reading the status register, if link fails to come
+ * up with auto-negotiation, then the link is forced if a signal is detected.
+ **/
+static s32 e1000_poll_fiber_serdes_link_generic(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 i, status;
+ s32 ret_val;
+
+ /*
+ * If we have a signal (the cable is plugged in, or assumed true for
+ * serdes media) then poll for a "Link-Up" indication in the Device
+ * Status Register. Time-out if a link isn't seen in 500 milliseconds
+ * seconds (Auto-negotiation should complete in less than 500
+ * milliseconds even if the other end is doing it in SW).
+ */
+ for (i = 0; i < FIBER_LINK_UP_LIMIT; i++) {
+ msleep(10);
+ status = er32(STATUS);
+ if (status & E1000_STATUS_LU)
+ break;
+ }
+ if (i == FIBER_LINK_UP_LIMIT) {
+ hw_dbg(hw, "Never got a valid link from auto-neg!!!\n");
+ mac->autoneg_failed = 1;
+ /*
+ * AutoNeg failed to achieve a link, so we'll call
+ * mac->check_for_link. This routine will force the
+ * link up if we detect a signal. This will allow us to
+ * communicate with non-autonegotiating link partners.
+ */
+ ret_val = mac->ops.check_for_link(hw);
+ if (ret_val) {
+ hw_dbg(hw, "Error while checking for link\n");
+ return ret_val;
+ }
+ mac->autoneg_failed = 0;
+ } else {
+ mac->autoneg_failed = 0;
+ hw_dbg(hw, "Valid Link Found\n");
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_setup_fiber_serdes_link - Setup link for fiber/serdes
+ * @hw: pointer to the HW structure
+ *
+ * Configures collision distance and flow control for fiber and serdes
+ * links. Upon successful setup, poll for link.
+ **/
+s32 e1000e_setup_fiber_serdes_link(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val;
+
+ ctrl = er32(CTRL);
+
+ /* Take the link out of reset */
+ ctrl &= ~E1000_CTRL_LRST;
+
+ e1000e_config_collision_dist(hw);
+
+ ret_val = e1000_commit_fc_settings_generic(hw);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Since auto-negotiation is enabled, take the link out of reset (the
+ * link will be in reset, because we previously reset the chip). This
+ * will restart auto-negotiation. If auto-negotiation is successful
+ * then the link-up status bit will be set and the flow control enable
+ * bits (RFCE and TFCE) will be set according to their negotiated value.
+ */
+ hw_dbg(hw, "Auto-negotiation enabled\n");
+
+ ew32(CTRL, ctrl);
+ e1e_flush();
+ msleep(1);
+
+ /*
+ * For these adapters, the SW definable pin 1 is set when the optics
+ * detect a signal. If we have a signal, then poll for a "Link-Up"
+ * indication.
+ */
+ if (hw->phy.media_type == e1000_media_type_internal_serdes ||
+ (er32(CTRL) & E1000_CTRL_SWDPIN1)) {
+ ret_val = e1000_poll_fiber_serdes_link_generic(hw);
+ } else {
+ hw_dbg(hw, "No signal detected\n");
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_config_collision_dist - Configure collision distance
+ * @hw: pointer to the HW structure
+ *
+ * Configures the collision distance to the default value and is used
+ * during link setup. Currently no func pointer exists and all
+ * implementations are handled in the generic version of this function.
+ **/
+void e1000e_config_collision_dist(struct e1000_hw *hw)
+{
+ u32 tctl;
+
+ tctl = er32(TCTL);
+
+ tctl &= ~E1000_TCTL_COLD;
+ tctl |= E1000_COLLISION_DISTANCE << E1000_COLD_SHIFT;
+
+ ew32(TCTL, tctl);
+ e1e_flush();
+}
+
+/**
+ * e1000e_set_fc_watermarks - Set flow control high/low watermarks
+ * @hw: pointer to the HW structure
+ *
+ * Sets the flow control high/low threshold (watermark) registers. If
+ * flow control XON frame transmission is enabled, then set XON frame
+ * transmission as well.
+ **/
+s32 e1000e_set_fc_watermarks(struct e1000_hw *hw)
+{
+ u32 fcrtl = 0, fcrth = 0;
+
+ /*
+ * Set the flow control receive threshold registers. Normally,
+ * these registers will be set to a default threshold that may be
+ * adjusted later by the driver's runtime code. However, if the
+ * ability to transmit pause frames is not enabled, then these
+ * registers will be set to 0.
+ */
+ if (hw->fc.type & e1000_fc_tx_pause) {
+ /*
+ * We need to set up the Receive Threshold high and low water
+ * marks as well as (optionally) enabling the transmission of
+ * XON frames.
+ */
+ fcrtl = hw->fc.low_water;
+ fcrtl |= E1000_FCRTL_XONE;
+ fcrth = hw->fc.high_water;
+ }
+ ew32(FCRTL, fcrtl);
+ ew32(FCRTH, fcrth);
+
+ return 0;
+}
+
+/**
+ * e1000e_force_mac_fc - Force the MAC's flow control settings
+ * @hw: pointer to the HW structure
+ *
+ * Force the MAC's flow control settings. Sets the TFCE and RFCE bits in the
+ * device control register to reflect the adapter settings. TFCE and RFCE
+ * need to be explicitly set by software when a copper PHY is used because
+ * autonegotiation is managed by the PHY rather than the MAC. Software must
+ * also configure these bits when link is forced on a fiber connection.
+ **/
+s32 e1000e_force_mac_fc(struct e1000_hw *hw)
+{
+ u32 ctrl;
+
+ ctrl = er32(CTRL);
+
+ /*
+ * Because we didn't get link via the internal auto-negotiation
+ * mechanism (we either forced link or we got link via PHY
+ * auto-neg), we have to manually enable/disable transmit an
+ * receive flow control.
+ *
+ * The "Case" statement below enables/disable flow control
+ * according to the "hw->fc.type" parameter.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause
+ * frames but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames
+ * frames but we do not receive pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) is enabled.
+ * other: No other values should be possible at this point.
+ */
+ hw_dbg(hw, "hw->fc.type = %u\n", hw->fc.type);
+
+ switch (hw->fc.type) {
+ case e1000_fc_none:
+ ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
+ break;
+ case e1000_fc_rx_pause:
+ ctrl &= (~E1000_CTRL_TFCE);
+ ctrl |= E1000_CTRL_RFCE;
+ break;
+ case e1000_fc_tx_pause:
+ ctrl &= (~E1000_CTRL_RFCE);
+ ctrl |= E1000_CTRL_TFCE;
+ break;
+ case e1000_fc_full:
+ ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE);
+ break;
+ default:
+ hw_dbg(hw, "Flow control param set incorrectly\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ ew32(CTRL, ctrl);
+
+ return 0;
+}
+
+/**
+ * e1000e_config_fc_after_link_up - Configures flow control after link
+ * @hw: pointer to the HW structure
+ *
+ * Checks the status of auto-negotiation after link up to ensure that the
+ * speed and duplex were not forced. If the link needed to be forced, then
+ * flow control needs to be forced also. If auto-negotiation is enabled
+ * and did not fail, then we configure flow control based on our link
+ * partner.
+ **/
+s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val = 0;
+ u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg;
+ u16 speed, duplex;
+
+ /*
+ * Check for the case where we have fiber media and auto-neg failed
+ * so we had to force link. In this case, we need to force the
+ * configuration of the MAC to match the "fc" parameter.
+ */
+ if (mac->autoneg_failed) {
+ if (hw->phy.media_type == e1000_media_type_fiber ||
+ hw->phy.media_type == e1000_media_type_internal_serdes)
+ ret_val = e1000e_force_mac_fc(hw);
+ } else {
+ if (hw->phy.media_type == e1000_media_type_copper)
+ ret_val = e1000e_force_mac_fc(hw);
+ }
+
+ if (ret_val) {
+ hw_dbg(hw, "Error forcing flow control settings\n");
+ return ret_val;
+ }
+
+ /*
+ * Check for the case where we have copper media and auto-neg is
+ * enabled. In this case, we need to check and see if Auto-Neg
+ * has completed, and if so, how the PHY and link partner has
+ * flow control configured.
+ */
+ if ((hw->phy.media_type == e1000_media_type_copper) && mac->autoneg) {
+ /*
+ * Read the MII Status Register and check to see if AutoNeg
+ * has completed. We read this twice because this reg has
+ * some "sticky" (latched) bits.
+ */
+ ret_val = e1e_rphy(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1e_rphy(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ if (!(mii_status_reg & MII_SR_AUTONEG_COMPLETE)) {
+ hw_dbg(hw, "Copper PHY and Auto Neg "
+ "has not completed.\n");
+ return ret_val;
+ }
+
+ /*
+ * The AutoNeg process has completed, so we now need to
+ * read both the Auto Negotiation Advertisement
+ * Register (Address 4) and the Auto_Negotiation Base
+ * Page Ability Register (Address 5) to determine how
+ * flow control was negotiated.
+ */
+ ret_val = e1e_rphy(hw, PHY_AUTONEG_ADV, &mii_nway_adv_reg);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1e_rphy(hw, PHY_LP_ABILITY, &mii_nway_lp_ability_reg);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Two bits in the Auto Negotiation Advertisement Register
+ * (Address 4) and two bits in the Auto Negotiation Base
+ * Page Ability Register (Address 5) determine flow control
+ * for both the PHY and the link partner. The following
+ * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
+ * 1999, describes these PAUSE resolution bits and how flow
+ * control is determined based upon these settings.
+ * NOTE: DC = Don't Care
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
+ *-------|---------|-------|---------|--------------------
+ * 0 | 0 | DC | DC | e1000_fc_none
+ * 0 | 1 | 0 | DC | e1000_fc_none
+ * 0 | 1 | 1 | 0 | e1000_fc_none
+ * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
+ * 1 | 0 | 0 | DC | e1000_fc_none
+ * 1 | DC | 1 | DC | e1000_fc_full
+ * 1 | 1 | 0 | 0 | e1000_fc_none
+ * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
+ *
+ *
+ * Are both PAUSE bits set to 1? If so, this implies
+ * Symmetric Flow Control is enabled at both ends. The
+ * ASM_DIR bits are irrelevant per the spec.
+ *
+ * For Symmetric Flow Control:
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | DC | 1 | DC | E1000_fc_full
+ *
+ */
+ if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
+ /*
+ * Now we need to check if the user selected Rx ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise Rx
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if (hw->fc.original_type == e1000_fc_full) {
+ hw->fc.type = e1000_fc_full;
+ hw_dbg(hw, "Flow Control = FULL.\r\n");
+ } else {
+ hw->fc.type = e1000_fc_rx_pause;
+ hw_dbg(hw, "Flow Control = "
+ "RX PAUSE frames only.\r\n");
+ }
+ }
+ /*
+ * For receiving PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
+ *
+ */
+ else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+ hw->fc.type = e1000_fc_tx_pause;
+ hw_dbg(hw, "Flow Control = Tx PAUSE frames only.\r\n");
+ }
+ /*
+ * For transmitting PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
+ *
+ */
+ else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+ hw->fc.type = e1000_fc_rx_pause;
+ hw_dbg(hw, "Flow Control = Rx PAUSE frames only.\r\n");
+ } else {
+ /*
+ * Per the IEEE spec, at this point flow control
+ * should be disabled.
+ */
+ hw->fc.type = e1000_fc_none;
+ hw_dbg(hw, "Flow Control = NONE.\r\n");
+ }
+
+ /*
+ * Now we need to do one last check... If we auto-
+ * negotiated to HALF DUPLEX, flow control should not be
+ * enabled per IEEE 802.3 spec.
+ */
+ ret_val = mac->ops.get_link_up_info(hw, &speed, &duplex);
+ if (ret_val) {
+ hw_dbg(hw, "Error getting link speed and duplex\n");
+ return ret_val;
+ }
+
+ if (duplex == HALF_DUPLEX)
+ hw->fc.type = e1000_fc_none;
+
+ /*
+ * Now we call a subroutine to actually force the MAC
+ * controller to use the correct flow control settings.
+ */
+ ret_val = e1000e_force_mac_fc(hw);
+ if (ret_val) {
+ hw_dbg(hw, "Error forcing flow control settings\n");
+ return ret_val;
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_get_speed_and_duplex_copper - Retrieve current speed/duplex
+ * @hw: pointer to the HW structure
+ * @speed: stores the current speed
+ * @duplex: stores the current duplex
+ *
+ * Read the status register for the current speed/duplex and store the current
+ * speed and duplex for copper connections.
+ **/
+s32 e1000e_get_speed_and_duplex_copper(struct e1000_hw *hw, u16 *speed, u16 *duplex)
+{
+ u32 status;
+
+ status = er32(STATUS);
+ if (status & E1000_STATUS_SPEED_1000) {
+ *speed = SPEED_1000;
+ hw_dbg(hw, "1000 Mbs, ");
+ } else if (status & E1000_STATUS_SPEED_100) {
+ *speed = SPEED_100;
+ hw_dbg(hw, "100 Mbs, ");
+ } else {
+ *speed = SPEED_10;
+ hw_dbg(hw, "10 Mbs, ");
+ }
+
+ if (status & E1000_STATUS_FD) {
+ *duplex = FULL_DUPLEX;
+ hw_dbg(hw, "Full Duplex\n");
+ } else {
+ *duplex = HALF_DUPLEX;
+ hw_dbg(hw, "Half Duplex\n");
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_get_speed_and_duplex_fiber_serdes - Retrieve current speed/duplex
+ * @hw: pointer to the HW structure
+ * @speed: stores the current speed
+ * @duplex: stores the current duplex
+ *
+ * Sets the speed and duplex to gigabit full duplex (the only possible option)
+ * for fiber/serdes links.
+ **/
+s32 e1000e_get_speed_and_duplex_fiber_serdes(struct e1000_hw *hw, u16 *speed, u16 *duplex)
+{
+ *speed = SPEED_1000;
+ *duplex = FULL_DUPLEX;
+
+ return 0;
+}
+
+/**
+ * e1000e_get_hw_semaphore - Acquire hardware semaphore
+ * @hw: pointer to the HW structure
+ *
+ * Acquire the HW semaphore to access the PHY or NVM
+ **/
+s32 e1000e_get_hw_semaphore(struct e1000_hw *hw)
+{
+ u32 swsm;
+ s32 timeout = hw->nvm.word_size + 1;
+ s32 i = 0;
+
+ /* Get the SW semaphore */
+ while (i < timeout) {
+ swsm = er32(SWSM);
+ if (!(swsm & E1000_SWSM_SMBI))
+ break;
+
+ udelay(50);
+ i++;
+ }
+
+ if (i == timeout) {
+ hw_dbg(hw, "Driver can't access device - SMBI bit is set.\n");
+ return -E1000_ERR_NVM;
+ }
+
+ /* Get the FW semaphore. */
+ for (i = 0; i < timeout; i++) {
+ swsm = er32(SWSM);
+ ew32(SWSM, swsm | E1000_SWSM_SWESMBI);
+
+ /* Semaphore acquired if bit latched */
+ if (er32(SWSM) & E1000_SWSM_SWESMBI)
+ break;
+
+ udelay(50);
+ }
+
+ if (i == timeout) {
+ /* Release semaphores */
+ e1000e_put_hw_semaphore(hw);
+ hw_dbg(hw, "Driver can't access the NVM\n");
+ return -E1000_ERR_NVM;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_put_hw_semaphore - Release hardware semaphore
+ * @hw: pointer to the HW structure
+ *
+ * Release hardware semaphore used to access the PHY or NVM
+ **/
+void e1000e_put_hw_semaphore(struct e1000_hw *hw)
+{
+ u32 swsm;
+
+ swsm = er32(SWSM);
+ swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI);
+ ew32(SWSM, swsm);
+}
+
+/**
+ * e1000e_get_auto_rd_done - Check for auto read completion
+ * @hw: pointer to the HW structure
+ *
+ * Check EEPROM for Auto Read done bit.
+ **/
+s32 e1000e_get_auto_rd_done(struct e1000_hw *hw)
+{
+ s32 i = 0;
+
+ while (i < AUTO_READ_DONE_TIMEOUT) {
+ if (er32(EECD) & E1000_EECD_AUTO_RD)
+ break;
+ msleep(1);
+ i++;
+ }
+
+ if (i == AUTO_READ_DONE_TIMEOUT) {
+ hw_dbg(hw, "Auto read by HW from NVM has not completed.\n");
+ return -E1000_ERR_RESET;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_valid_led_default - Verify a valid default LED config
+ * @hw: pointer to the HW structure
+ * @data: pointer to the NVM (EEPROM)
+ *
+ * Read the EEPROM for the current default LED configuration. If the
+ * LED configuration is not valid, set to a valid LED configuration.
+ **/
+s32 e1000e_valid_led_default(struct e1000_hw *hw, u16 *data)
+{
+ s32 ret_val;
+
+ ret_val = e1000_read_nvm(hw, NVM_ID_LED_SETTINGS, 1, data);
+ if (ret_val) {
+ hw_dbg(hw, "NVM Read Error\n");
+ return ret_val;
+ }
+
+ if (*data == ID_LED_RESERVED_0000 || *data == ID_LED_RESERVED_FFFF)
+ *data = ID_LED_DEFAULT;
+
+ return 0;
+}
+
+/**
+ * e1000e_id_led_init -
+ * @hw: pointer to the HW structure
+ *
+ **/
+s32 e1000e_id_led_init(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val;
+ const u32 ledctl_mask = 0x000000FF;
+ const u32 ledctl_on = E1000_LEDCTL_MODE_LED_ON;
+ const u32 ledctl_off = E1000_LEDCTL_MODE_LED_OFF;
+ u16 data, i, temp;
+ const u16 led_mask = 0x0F;
+
+ ret_val = hw->nvm.ops.valid_led_default(hw, &data);
+ if (ret_val)
+ return ret_val;
+
+ mac->ledctl_default = er32(LEDCTL);
+ mac->ledctl_mode1 = mac->ledctl_default;
+ mac->ledctl_mode2 = mac->ledctl_default;
+
+ for (i = 0; i < 4; i++) {
+ temp = (data >> (i << 2)) & led_mask;
+ switch (temp) {
+ case ID_LED_ON1_DEF2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_ON1_OFF2:
+ mac->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+ mac->ledctl_mode1 |= ledctl_on << (i << 3);
+ break;
+ case ID_LED_OFF1_DEF2:
+ case ID_LED_OFF1_ON2:
+ case ID_LED_OFF1_OFF2:
+ mac->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+ mac->ledctl_mode1 |= ledctl_off << (i << 3);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ switch (temp) {
+ case ID_LED_DEF1_ON2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_OFF1_ON2:
+ mac->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+ mac->ledctl_mode2 |= ledctl_on << (i << 3);
+ break;
+ case ID_LED_DEF1_OFF2:
+ case ID_LED_ON1_OFF2:
+ case ID_LED_OFF1_OFF2:
+ mac->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+ mac->ledctl_mode2 |= ledctl_off << (i << 3);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_cleanup_led_generic - Set LED config to default operation
+ * @hw: pointer to the HW structure
+ *
+ * Remove the current LED configuration and set the LED configuration
+ * to the default value, saved from the EEPROM.
+ **/
+s32 e1000e_cleanup_led_generic(struct e1000_hw *hw)
+{
+ ew32(LEDCTL, hw->mac.ledctl_default);
+ return 0;
+}
+
+/**
+ * e1000e_blink_led - Blink LED
+ * @hw: pointer to the HW structure
+ *
+ * Blink the LEDs which are set to be on.
+ **/
+s32 e1000e_blink_led(struct e1000_hw *hw)
+{
+ u32 ledctl_blink = 0;
+ u32 i;
+
+ if (hw->phy.media_type == e1000_media_type_fiber) {
+ /* always blink LED0 for PCI-E fiber */
+ ledctl_blink = E1000_LEDCTL_LED0_BLINK |
+ (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT);
+ } else {
+ /*
+ * set the blink bit for each LED that's "on" (0x0E)
+ * in ledctl_mode2
+ */
+ ledctl_blink = hw->mac.ledctl_mode2;
+ for (i = 0; i < 4; i++)
+ if (((hw->mac.ledctl_mode2 >> (i * 8)) & 0xFF) ==
+ E1000_LEDCTL_MODE_LED_ON)
+ ledctl_blink |= (E1000_LEDCTL_LED0_BLINK <<
+ (i * 8));
+ }
+
+ ew32(LEDCTL, ledctl_blink);
+
+ return 0;
+}
+
+/**
+ * e1000e_led_on_generic - Turn LED on
+ * @hw: pointer to the HW structure
+ *
+ * Turn LED on.
+ **/
+s32 e1000e_led_on_generic(struct e1000_hw *hw)
+{
+ u32 ctrl;
+
+ switch (hw->phy.media_type) {
+ case e1000_media_type_fiber:
+ ctrl = er32(CTRL);
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ ew32(CTRL, ctrl);
+ break;
+ case e1000_media_type_copper:
+ ew32(LEDCTL, hw->mac.ledctl_mode2);
+ break;
+ default:
+ break;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_led_off_generic - Turn LED off
+ * @hw: pointer to the HW structure
+ *
+ * Turn LED off.
+ **/
+s32 e1000e_led_off_generic(struct e1000_hw *hw)
+{
+ u32 ctrl;
+
+ switch (hw->phy.media_type) {
+ case e1000_media_type_fiber:
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ ew32(CTRL, ctrl);
+ break;
+ case e1000_media_type_copper:
+ ew32(LEDCTL, hw->mac.ledctl_mode1);
+ break;
+ default:
+ break;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_set_pcie_no_snoop - Set PCI-express capabilities
+ * @hw: pointer to the HW structure
+ * @no_snoop: bitmap of snoop events
+ *
+ * Set the PCI-express register to snoop for events enabled in 'no_snoop'.
+ **/
+void e1000e_set_pcie_no_snoop(struct e1000_hw *hw, u32 no_snoop)
+{
+ u32 gcr;
+
+ if (no_snoop) {
+ gcr = er32(GCR);
+ gcr &= ~(PCIE_NO_SNOOP_ALL);
+ gcr |= no_snoop;
+ ew32(GCR, gcr);
+ }
+}
+
+/**
+ * e1000e_disable_pcie_master - Disables PCI-express master access
+ * @hw: pointer to the HW structure
+ *
+ * Returns 0 if successful, else returns -10
+ * (-E1000_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not caused
+ * the master requests to be disabled.
+ *
+ * Disables PCI-Express master access and verifies there are no pending
+ * requests.
+ **/
+s32 e1000e_disable_pcie_master(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 timeout = MASTER_DISABLE_TIMEOUT;
+
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_GIO_MASTER_DISABLE;
+ ew32(CTRL, ctrl);
+
+ while (timeout) {
+ if (!(er32(STATUS) &
+ E1000_STATUS_GIO_MASTER_ENABLE))
+ break;
+ udelay(100);
+ timeout--;
+ }
+
+ if (!timeout) {
+ hw_dbg(hw, "Master requests are pending.\n");
+ return -E1000_ERR_MASTER_REQUESTS_PENDING;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_reset_adaptive - Reset Adaptive Interframe Spacing
+ * @hw: pointer to the HW structure
+ *
+ * Reset the Adaptive Interframe Spacing throttle to default values.
+ **/
+void e1000e_reset_adaptive(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+
+ mac->current_ifs_val = 0;
+ mac->ifs_min_val = IFS_MIN;
+ mac->ifs_max_val = IFS_MAX;
+ mac->ifs_step_size = IFS_STEP;
+ mac->ifs_ratio = IFS_RATIO;
+
+ mac->in_ifs_mode = 0;
+ ew32(AIT, 0);
+}
+
+/**
+ * e1000e_update_adaptive - Update Adaptive Interframe Spacing
+ * @hw: pointer to the HW structure
+ *
+ * Update the Adaptive Interframe Spacing Throttle value based on the
+ * time between transmitted packets and time between collisions.
+ **/
+void e1000e_update_adaptive(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+
+ if ((mac->collision_delta * mac->ifs_ratio) > mac->tx_packet_delta) {
+ if (mac->tx_packet_delta > MIN_NUM_XMITS) {
+ mac->in_ifs_mode = 1;
+ if (mac->current_ifs_val < mac->ifs_max_val) {
+ if (!mac->current_ifs_val)
+ mac->current_ifs_val = mac->ifs_min_val;
+ else
+ mac->current_ifs_val +=
+ mac->ifs_step_size;
+ ew32(AIT, mac->current_ifs_val);
+ }
+ }
+ } else {
+ if (mac->in_ifs_mode &&
+ (mac->tx_packet_delta <= MIN_NUM_XMITS)) {
+ mac->current_ifs_val = 0;
+ mac->in_ifs_mode = 0;
+ ew32(AIT, 0);
+ }
+ }
+}
+
+/**
+ * e1000_raise_eec_clk - Raise EEPROM clock
+ * @hw: pointer to the HW structure
+ * @eecd: pointer to the EEPROM
+ *
+ * Enable/Raise the EEPROM clock bit.
+ **/
+static void e1000_raise_eec_clk(struct e1000_hw *hw, u32 *eecd)
+{
+ *eecd = *eecd | E1000_EECD_SK;
+ ew32(EECD, *eecd);
+ e1e_flush();
+ udelay(hw->nvm.delay_usec);
+}
+
+/**
+ * e1000_lower_eec_clk - Lower EEPROM clock
+ * @hw: pointer to the HW structure
+ * @eecd: pointer to the EEPROM
+ *
+ * Clear/Lower the EEPROM clock bit.
+ **/
+static void e1000_lower_eec_clk(struct e1000_hw *hw, u32 *eecd)
+{
+ *eecd = *eecd & ~E1000_EECD_SK;
+ ew32(EECD, *eecd);
+ e1e_flush();
+ udelay(hw->nvm.delay_usec);
+}
+
+/**
+ * e1000_shift_out_eec_bits - Shift data bits our to the EEPROM
+ * @hw: pointer to the HW structure
+ * @data: data to send to the EEPROM
+ * @count: number of bits to shift out
+ *
+ * We need to shift 'count' bits out to the EEPROM. So, the value in the
+ * "data" parameter will be shifted out to the EEPROM one bit at a time.
+ * In order to do this, "data" must be broken down into bits.
+ **/
+static void e1000_shift_out_eec_bits(struct e1000_hw *hw, u16 data, u16 count)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ u32 eecd = er32(EECD);
+ u32 mask;
+
+ mask = 0x01 << (count - 1);
+ if (nvm->type == e1000_nvm_eeprom_spi)
+ eecd |= E1000_EECD_DO;
+
+ do {
+ eecd &= ~E1000_EECD_DI;
+
+ if (data & mask)
+ eecd |= E1000_EECD_DI;
+
+ ew32(EECD, eecd);
+ e1e_flush();
+
+ udelay(nvm->delay_usec);
+
+ e1000_raise_eec_clk(hw, &eecd);
+ e1000_lower_eec_clk(hw, &eecd);
+
+ mask >>= 1;
+ } while (mask);
+
+ eecd &= ~E1000_EECD_DI;
+ ew32(EECD, eecd);
+}
+
+/**
+ * e1000_shift_in_eec_bits - Shift data bits in from the EEPROM
+ * @hw: pointer to the HW structure
+ * @count: number of bits to shift in
+ *
+ * In order to read a register from the EEPROM, we need to shift 'count' bits
+ * in from the EEPROM. Bits are "shifted in" by raising the clock input to
+ * the EEPROM (setting the SK bit), and then reading the value of the data out
+ * "DO" bit. During this "shifting in" process the data in "DI" bit should
+ * always be clear.
+ **/
+static u16 e1000_shift_in_eec_bits(struct e1000_hw *hw, u16 count)
+{
+ u32 eecd;
+ u32 i;
+ u16 data;
+
+ eecd = er32(EECD);
+
+ eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
+ data = 0;
+
+ for (i = 0; i < count; i++) {
+ data <<= 1;
+ e1000_raise_eec_clk(hw, &eecd);
+
+ eecd = er32(EECD);
+
+ eecd &= ~E1000_EECD_DI;
+ if (eecd & E1000_EECD_DO)
+ data |= 1;
+
+ e1000_lower_eec_clk(hw, &eecd);
+ }
+
+ return data;
+}
+
+/**
+ * e1000e_poll_eerd_eewr_done - Poll for EEPROM read/write completion
+ * @hw: pointer to the HW structure
+ * @ee_reg: EEPROM flag for polling
+ *
+ * Polls the EEPROM status bit for either read or write completion based
+ * upon the value of 'ee_reg'.
+ **/
+s32 e1000e_poll_eerd_eewr_done(struct e1000_hw *hw, int ee_reg)
+{
+ u32 attempts = 100000;
+ u32 i, reg = 0;
+
+ for (i = 0; i < attempts; i++) {
+ if (ee_reg == E1000_NVM_POLL_READ)
+ reg = er32(EERD);
+ else
+ reg = er32(EEWR);
+
+ if (reg & E1000_NVM_RW_REG_DONE)
+ return 0;
+
+ udelay(5);
+ }
+
+ return -E1000_ERR_NVM;
+}
+
+/**
+ * e1000e_acquire_nvm - Generic request for access to EEPROM
+ * @hw: pointer to the HW structure
+ *
+ * Set the EEPROM access request bit and wait for EEPROM access grant bit.
+ * Return successful if access grant bit set, else clear the request for
+ * EEPROM access and return -E1000_ERR_NVM (-1).
+ **/
+s32 e1000e_acquire_nvm(struct e1000_hw *hw)
+{
+ u32 eecd = er32(EECD);
+ s32 timeout = E1000_NVM_GRANT_ATTEMPTS;
+
+ ew32(EECD, eecd | E1000_EECD_REQ);
+ eecd = er32(EECD);
+
+ while (timeout) {
+ if (eecd & E1000_EECD_GNT)
+ break;
+ udelay(5);
+ eecd = er32(EECD);
+ timeout--;
+ }
+
+ if (!timeout) {
+ eecd &= ~E1000_EECD_REQ;
+ ew32(EECD, eecd);
+ hw_dbg(hw, "Could not acquire NVM grant\n");
+ return -E1000_ERR_NVM;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_standby_nvm - Return EEPROM to standby state
+ * @hw: pointer to the HW structure
+ *
+ * Return the EEPROM to a standby state.
+ **/
+static void e1000_standby_nvm(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ u32 eecd = er32(EECD);
+
+ if (nvm->type == e1000_nvm_eeprom_spi) {
+ /* Toggle CS to flush commands */
+ eecd |= E1000_EECD_CS;
+ ew32(EECD, eecd);
+ e1e_flush();
+ udelay(nvm->delay_usec);
+ eecd &= ~E1000_EECD_CS;
+ ew32(EECD, eecd);
+ e1e_flush();
+ udelay(nvm->delay_usec);
+ }
+}
+
+/**
+ * e1000_stop_nvm - Terminate EEPROM command
+ * @hw: pointer to the HW structure
+ *
+ * Terminates the current command by inverting the EEPROM's chip select pin.
+ **/
+static void e1000_stop_nvm(struct e1000_hw *hw)
+{
+ u32 eecd;
+
+ eecd = er32(EECD);
+ if (hw->nvm.type == e1000_nvm_eeprom_spi) {
+ /* Pull CS high */
+ eecd |= E1000_EECD_CS;
+ e1000_lower_eec_clk(hw, &eecd);
+ }
+}
+
+/**
+ * e1000e_release_nvm - Release exclusive access to EEPROM
+ * @hw: pointer to the HW structure
+ *
+ * Stop any current commands to the EEPROM and clear the EEPROM request bit.
+ **/
+void e1000e_release_nvm(struct e1000_hw *hw)
+{
+ u32 eecd;
+
+ e1000_stop_nvm(hw);
+
+ eecd = er32(EECD);
+ eecd &= ~E1000_EECD_REQ;
+ ew32(EECD, eecd);
+}
+
+/**
+ * e1000_ready_nvm_eeprom - Prepares EEPROM for read/write
+ * @hw: pointer to the HW structure
+ *
+ * Setups the EEPROM for reading and writing.
+ **/
+static s32 e1000_ready_nvm_eeprom(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ u32 eecd = er32(EECD);
+ u16 timeout = 0;
+ u8 spi_stat_reg;
+
+ if (nvm->type == e1000_nvm_eeprom_spi) {
+ /* Clear SK and CS */
+ eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
+ ew32(EECD, eecd);
+ udelay(1);
+ timeout = NVM_MAX_RETRY_SPI;
+
+ /*
+ * Read "Status Register" repeatedly until the LSB is cleared.
+ * The EEPROM will signal that the command has been completed
+ * by clearing bit 0 of the internal status register. If it's
+ * not cleared within 'timeout', then error out.
+ */
+ while (timeout) {
+ e1000_shift_out_eec_bits(hw, NVM_RDSR_OPCODE_SPI,
+ hw->nvm.opcode_bits);
+ spi_stat_reg = (u8)e1000_shift_in_eec_bits(hw, 8);
+ if (!(spi_stat_reg & NVM_STATUS_RDY_SPI))
+ break;
+
+ udelay(5);
+ e1000_standby_nvm(hw);
+ timeout--;
+ }
+
+ if (!timeout) {
+ hw_dbg(hw, "SPI NVM Status error\n");
+ return -E1000_ERR_NVM;
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_read_nvm_eerd - Reads EEPROM using EERD register
+ * @hw: pointer to the HW structure
+ * @offset: offset of word in the EEPROM to read
+ * @words: number of words to read
+ * @data: word read from the EEPROM
+ *
+ * Reads a 16 bit word from the EEPROM using the EERD register.
+ **/
+s32 e1000e_read_nvm_eerd(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ u32 i, eerd = 0;
+ s32 ret_val = 0;
+
+ /*
+ * A check for invalid values: offset too large, too many words,
+ * too many words for the offset, and not enough words.
+ */
+ if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) ||
+ (words == 0)) {
+ hw_dbg(hw, "nvm parameter(s) out of bounds\n");
+ return -E1000_ERR_NVM;
+ }
+
+ for (i = 0; i < words; i++) {
+ eerd = ((offset+i) << E1000_NVM_RW_ADDR_SHIFT) +
+ E1000_NVM_RW_REG_START;
+
+ ew32(EERD, eerd);
+ ret_val = e1000e_poll_eerd_eewr_done(hw, E1000_NVM_POLL_READ);
+ if (ret_val)
+ break;
+
+ data[i] = (er32(EERD) >> E1000_NVM_RW_REG_DATA);
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000e_write_nvm_spi - Write to EEPROM using SPI
+ * @hw: pointer to the HW structure
+ * @offset: offset within the EEPROM to be written to
+ * @words: number of words to write
+ * @data: 16 bit word(s) to be written to the EEPROM
+ *
+ * Writes data to EEPROM at offset using SPI interface.
+ *
+ * If e1000e_update_nvm_checksum is not called after this function , the
+ * EEPROM will most likely contain an invalid checksum.
+ **/
+s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ s32 ret_val;
+ u16 widx = 0;
+
+ /*
+ * A check for invalid values: offset too large, too many words,
+ * and not enough words.
+ */
+ if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) ||
+ (words == 0)) {
+ hw_dbg(hw, "nvm parameter(s) out of bounds\n");
+ return -E1000_ERR_NVM;
+ }
+
+ ret_val = nvm->ops.acquire_nvm(hw);
+ if (ret_val)
+ return ret_val;
+
+ msleep(10);
+
+ while (widx < words) {
+ u8 write_opcode = NVM_WRITE_OPCODE_SPI;
+
+ ret_val = e1000_ready_nvm_eeprom(hw);
+ if (ret_val) {
+ nvm->ops.release_nvm(hw);
+ return ret_val;
+ }
+
+ e1000_standby_nvm(hw);
+
+ /* Send the WRITE ENABLE command (8 bit opcode) */
+ e1000_shift_out_eec_bits(hw, NVM_WREN_OPCODE_SPI,
+ nvm->opcode_bits);
+
+ e1000_standby_nvm(hw);
+
+ /*
+ * Some SPI eeproms use the 8th address bit embedded in the
+ * opcode
+ */
+ if ((nvm->address_bits == 8) && (offset >= 128))
+ write_opcode |= NVM_A8_OPCODE_SPI;
+
+ /* Send the Write command (8-bit opcode + addr) */
+ e1000_shift_out_eec_bits(hw, write_opcode, nvm->opcode_bits);
+ e1000_shift_out_eec_bits(hw, (u16)((offset + widx) * 2),
+ nvm->address_bits);
+
+ /* Loop to allow for up to whole page write of eeprom */
+ while (widx < words) {
+ u16 word_out = data[widx];
+ word_out = (word_out >> 8) | (word_out << 8);
+ e1000_shift_out_eec_bits(hw, word_out, 16);
+ widx++;
+
+ if ((((offset + widx) * 2) % nvm->page_size) == 0) {
+ e1000_standby_nvm(hw);
+ break;
+ }
+ }
+ }
+
+ msleep(10);
+ return 0;
+}
+
+/**
+ * e1000e_read_mac_addr - Read device MAC address
+ * @hw: pointer to the HW structure
+ *
+ * Reads the device MAC address from the EEPROM and stores the value.
+ * Since devices with two ports use the same EEPROM, we increment the
+ * last bit in the MAC address for the second port.
+ **/
+s32 e1000e_read_mac_addr(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 offset, nvm_data, i;
+ u16 mac_addr_offset = 0;
+
+ if (hw->mac.type == e1000_82571) {
+ /* Check for an alternate MAC address. An alternate MAC
+ * address can be setup by pre-boot software and must be
+ * treated like a permanent address and must override the
+ * actual permanent MAC address.*/
+ ret_val = e1000_read_nvm(hw, NVM_ALT_MAC_ADDR_PTR, 1,
+ &mac_addr_offset);
+ if (ret_val) {
+ hw_dbg(hw, "NVM Read Error\n");
+ return ret_val;
+ }
+ if (mac_addr_offset == 0xFFFF)
+ mac_addr_offset = 0;
+
+ if (mac_addr_offset) {
+ if (hw->bus.func == E1000_FUNC_1)
+ mac_addr_offset += ETH_ALEN/sizeof(u16);
+
+ /* make sure we have a valid mac address here
+ * before using it */
+ ret_val = e1000_read_nvm(hw, mac_addr_offset, 1,
+ &nvm_data);
+ if (ret_val) {
+ hw_dbg(hw, "NVM Read Error\n");
+ return ret_val;
+ }
+ if (nvm_data & 0x0001)
+ mac_addr_offset = 0;
+ }
+
+ if (mac_addr_offset)
+ hw->dev_spec.e82571.alt_mac_addr_is_present = 1;
+ }
+
+ for (i = 0; i < ETH_ALEN; i += 2) {
+ offset = mac_addr_offset + (i >> 1);
+ ret_val = e1000_read_nvm(hw, offset, 1, &nvm_data);
+ if (ret_val) {
+ hw_dbg(hw, "NVM Read Error\n");
+ return ret_val;
+ }
+ hw->mac.perm_addr[i] = (u8)(nvm_data & 0xFF);
+ hw->mac.perm_addr[i+1] = (u8)(nvm_data >> 8);
+ }
+
+ /* Flip last bit of mac address if we're on second port */
+ if (!mac_addr_offset && hw->bus.func == E1000_FUNC_1)
+ hw->mac.perm_addr[5] ^= 1;
+
+ for (i = 0; i < ETH_ALEN; i++)
+ hw->mac.addr[i] = hw->mac.perm_addr[i];
+
+ return 0;
+}
+
+/**
+ * e1000e_validate_nvm_checksum_generic - Validate EEPROM checksum
+ * @hw: pointer to the HW structure
+ *
+ * Calculates the EEPROM checksum by reading/adding each word of the EEPROM
+ * and then verifies that the sum of the EEPROM is equal to 0xBABA.
+ **/
+s32 e1000e_validate_nvm_checksum_generic(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 checksum = 0;
+ u16 i, nvm_data;
+
+ for (i = 0; i < (NVM_CHECKSUM_REG + 1); i++) {
+ ret_val = e1000_read_nvm(hw, i, 1, &nvm_data);
+ if (ret_val) {
+ hw_dbg(hw, "NVM Read Error\n");
+ return ret_val;
+ }
+ checksum += nvm_data;
+ }
+
+ if (checksum != (u16) NVM_SUM) {
+ hw_dbg(hw, "NVM Checksum Invalid\n");
+ return -E1000_ERR_NVM;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_update_nvm_checksum_generic - Update EEPROM checksum
+ * @hw: pointer to the HW structure
+ *
+ * Updates the EEPROM checksum by reading/adding each word of the EEPROM
+ * up to the checksum. Then calculates the EEPROM checksum and writes the
+ * value to the EEPROM.
+ **/
+s32 e1000e_update_nvm_checksum_generic(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 checksum = 0;
+ u16 i, nvm_data;
+
+ for (i = 0; i < NVM_CHECKSUM_REG; i++) {
+ ret_val = e1000_read_nvm(hw, i, 1, &nvm_data);
+ if (ret_val) {
+ hw_dbg(hw, "NVM Read Error while updating checksum.\n");
+ return ret_val;
+ }
+ checksum += nvm_data;
+ }
+ checksum = (u16) NVM_SUM - checksum;
+ ret_val = e1000_write_nvm(hw, NVM_CHECKSUM_REG, 1, &checksum);
+ if (ret_val)
+ hw_dbg(hw, "NVM Write Error while updating checksum.\n");
+
+ return ret_val;
+}
+
+/**
+ * e1000e_reload_nvm - Reloads EEPROM
+ * @hw: pointer to the HW structure
+ *
+ * Reloads the EEPROM by setting the "Reinitialize from EEPROM" bit in the
+ * extended control register.
+ **/
+void e1000e_reload_nvm(struct e1000_hw *hw)
+{
+ u32 ctrl_ext;
+
+ udelay(10);
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_EE_RST;
+ ew32(CTRL_EXT, ctrl_ext);
+ e1e_flush();
+}
+
+/**
+ * e1000_calculate_checksum - Calculate checksum for buffer
+ * @buffer: pointer to EEPROM
+ * @length: size of EEPROM to calculate a checksum for
+ *
+ * Calculates the checksum for some buffer on a specified length. The
+ * checksum calculated is returned.
+ **/
+static u8 e1000_calculate_checksum(u8 *buffer, u32 length)
+{
+ u32 i;
+ u8 sum = 0;
+
+ if (!buffer)
+ return 0;
+
+ for (i = 0; i < length; i++)
+ sum += buffer[i];
+
+ return (u8) (0 - sum);
+}
+
+/**
+ * e1000_mng_enable_host_if - Checks host interface is enabled
+ * @hw: pointer to the HW structure
+ *
+ * Returns E1000_success upon success, else E1000_ERR_HOST_INTERFACE_COMMAND
+ *
+ * This function checks whether the HOST IF is enabled for command operation
+ * and also checks whether the previous command is completed. It busy waits
+ * in case of previous command is not completed.
+ **/
+static s32 e1000_mng_enable_host_if(struct e1000_hw *hw)
+{
+ u32 hicr;
+ u8 i;
+
+ /* Check that the host interface is enabled. */
+ hicr = er32(HICR);
+ if ((hicr & E1000_HICR_EN) == 0) {
+ hw_dbg(hw, "E1000_HOST_EN bit disabled.\n");
+ return -E1000_ERR_HOST_INTERFACE_COMMAND;
+ }
+ /* check the previous command is completed */
+ for (i = 0; i < E1000_MNG_DHCP_COMMAND_TIMEOUT; i++) {
+ hicr = er32(HICR);
+ if (!(hicr & E1000_HICR_C))
+ break;
+ mdelay(1);
+ }
+
+ if (i == E1000_MNG_DHCP_COMMAND_TIMEOUT) {
+ hw_dbg(hw, "Previous command timeout failed .\n");
+ return -E1000_ERR_HOST_INTERFACE_COMMAND;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_check_mng_mode_generic - check management mode
+ * @hw: pointer to the HW structure
+ *
+ * Reads the firmware semaphore register and returns true (>0) if
+ * manageability is enabled, else false (0).
+ **/
+bool e1000e_check_mng_mode_generic(struct e1000_hw *hw)
+{
+ u32 fwsm = er32(FWSM);
+
+ return (fwsm & E1000_FWSM_MODE_MASK) ==
+ (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT);
+}
+
+/**
+ * e1000e_enable_tx_pkt_filtering - Enable packet filtering on Tx
+ * @hw: pointer to the HW structure
+ *
+ * Enables packet filtering on transmit packets if manageability is enabled
+ * and host interface is enabled.
+ **/
+bool e1000e_enable_tx_pkt_filtering(struct e1000_hw *hw)
+{
+ struct e1000_host_mng_dhcp_cookie *hdr = &hw->mng_cookie;
+ u32 *buffer = (u32 *)&hw->mng_cookie;
+ u32 offset;
+ s32 ret_val, hdr_csum, csum;
+ u8 i, len;
+
+ /* No manageability, no filtering */
+ if (!e1000e_check_mng_mode(hw)) {
+ hw->mac.tx_pkt_filtering = 0;
+ return 0;
+ }
+
+ /*
+ * If we can't read from the host interface for whatever
+ * reason, disable filtering.
+ */
+ ret_val = e1000_mng_enable_host_if(hw);
+ if (ret_val != 0) {
+ hw->mac.tx_pkt_filtering = 0;
+ return ret_val;
+ }
+
+ /* Read in the header. Length and offset are in dwords. */
+ len = E1000_MNG_DHCP_COOKIE_LENGTH >> 2;
+ offset = E1000_MNG_DHCP_COOKIE_OFFSET >> 2;
+ for (i = 0; i < len; i++)
+ *(buffer + i) = E1000_READ_REG_ARRAY(hw, E1000_HOST_IF, offset + i);
+ hdr_csum = hdr->checksum;
+ hdr->checksum = 0;
+ csum = e1000_calculate_checksum((u8 *)hdr,
+ E1000_MNG_DHCP_COOKIE_LENGTH);
+ /*
+ * If either the checksums or signature don't match, then
+ * the cookie area isn't considered valid, in which case we
+ * take the safe route of assuming Tx filtering is enabled.
+ */
+ if ((hdr_csum != csum) || (hdr->signature != E1000_IAMT_SIGNATURE)) {
+ hw->mac.tx_pkt_filtering = 1;
+ return 1;
+ }
+
+ /* Cookie area is valid, make the final check for filtering. */
+ if (!(hdr->status & E1000_MNG_DHCP_COOKIE_STATUS_PARSING)) {
+ hw->mac.tx_pkt_filtering = 0;
+ return 0;
+ }
+
+ hw->mac.tx_pkt_filtering = 1;
+ return 1;
+}
+
+/**
+ * e1000_mng_write_cmd_header - Writes manageability command header
+ * @hw: pointer to the HW structure
+ * @hdr: pointer to the host interface command header
+ *
+ * Writes the command header after does the checksum calculation.
+ **/
+static s32 e1000_mng_write_cmd_header(struct e1000_hw *hw,
+ struct e1000_host_mng_command_header *hdr)
+{
+ u16 i, length = sizeof(struct e1000_host_mng_command_header);
+
+ /* Write the whole command header structure with new checksum. */
+
+ hdr->checksum = e1000_calculate_checksum((u8 *)hdr, length);
+
+ length >>= 2;
+ /* Write the relevant command block into the ram area. */
+ for (i = 0; i < length; i++) {
+ E1000_WRITE_REG_ARRAY(hw, E1000_HOST_IF, i,
+ *((u32 *) hdr + i));
+ e1e_flush();
+ }
+
+ return 0;
+}
+
+/**
+ * e1000_mng_host_if_write - Writes to the manageability host interface
+ * @hw: pointer to the HW structure
+ * @buffer: pointer to the host interface buffer
+ * @length: size of the buffer
+ * @offset: location in the buffer to write to
+ * @sum: sum of the data (not checksum)
+ *
+ * This function writes the buffer content at the offset given on the host if.
+ * It also does alignment considerations to do the writes in most efficient
+ * way. Also fills up the sum of the buffer in *buffer parameter.
+ **/
+static s32 e1000_mng_host_if_write(struct e1000_hw *hw, u8 *buffer,
+ u16 length, u16 offset, u8 *sum)
+{
+ u8 *tmp;
+ u8 *bufptr = buffer;
+ u32 data = 0;
+ u16 remaining, i, j, prev_bytes;
+
+ /* sum = only sum of the data and it is not checksum */
+
+ if (length == 0 || offset + length > E1000_HI_MAX_MNG_DATA_LENGTH)
+ return -E1000_ERR_PARAM;
+
+ tmp = (u8 *)&data;
+ prev_bytes = offset & 0x3;
+ offset >>= 2;
+
+ if (prev_bytes) {
+ data = E1000_READ_REG_ARRAY(hw, E1000_HOST_IF, offset);
+ for (j = prev_bytes; j < sizeof(u32); j++) {
+ *(tmp + j) = *bufptr++;
+ *sum += *(tmp + j);
+ }
+ E1000_WRITE_REG_ARRAY(hw, E1000_HOST_IF, offset, data);
+ length -= j - prev_bytes;
+ offset++;
+ }
+
+ remaining = length & 0x3;
+ length -= remaining;
+
+ /* Calculate length in DWORDs */
+ length >>= 2;
+
+ /*
+ * The device driver writes the relevant command block into the
+ * ram area.
+ */
+ for (i = 0; i < length; i++) {
+ for (j = 0; j < sizeof(u32); j++) {
+ *(tmp + j) = *bufptr++;
+ *sum += *(tmp + j);
+ }
+
+ E1000_WRITE_REG_ARRAY(hw, E1000_HOST_IF, offset + i, data);
+ }
+ if (remaining) {
+ for (j = 0; j < sizeof(u32); j++) {
+ if (j < remaining)
+ *(tmp + j) = *bufptr++;
+ else
+ *(tmp + j) = 0;
+
+ *sum += *(tmp + j);
+ }
+ E1000_WRITE_REG_ARRAY(hw, E1000_HOST_IF, offset + i, data);
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_mng_write_dhcp_info - Writes DHCP info to host interface
+ * @hw: pointer to the HW structure
+ * @buffer: pointer to the host interface
+ * @length: size of the buffer
+ *
+ * Writes the DHCP information to the host interface.
+ **/
+s32 e1000e_mng_write_dhcp_info(struct e1000_hw *hw, u8 *buffer, u16 length)
+{
+ struct e1000_host_mng_command_header hdr;
+ s32 ret_val;
+ u32 hicr;
+
+ hdr.command_id = E1000_MNG_DHCP_TX_PAYLOAD_CMD;
+ hdr.command_length = length;
+ hdr.reserved1 = 0;
+ hdr.reserved2 = 0;
+ hdr.checksum = 0;
+
+ /* Enable the host interface */
+ ret_val = e1000_mng_enable_host_if(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Populate the host interface with the contents of "buffer". */
+ ret_val = e1000_mng_host_if_write(hw, buffer, length,
+ sizeof(hdr), &(hdr.checksum));
+ if (ret_val)
+ return ret_val;
+
+ /* Write the manageability command header */
+ ret_val = e1000_mng_write_cmd_header(hw, &hdr);
+ if (ret_val)
+ return ret_val;
+
+ /* Tell the ARC a new command is pending. */
+ hicr = er32(HICR);
+ ew32(HICR, hicr | E1000_HICR_C);
+
+ return 0;
+}
+
+/**
+ * e1000e_enable_mng_pass_thru - Enable processing of ARP's
+ * @hw: pointer to the HW structure
+ *
+ * Verifies the hardware needs to allow ARPs to be processed by the host.
+ **/
+bool e1000e_enable_mng_pass_thru(struct e1000_hw *hw)
+{
+ u32 manc;
+ u32 fwsm, factps;
+ bool ret_val = 0;
+
+ manc = er32(MANC);
+
+ if (!(manc & E1000_MANC_RCV_TCO_EN) ||
+ !(manc & E1000_MANC_EN_MAC_ADDR_FILTER))
+ return ret_val;
+
+ if (hw->mac.arc_subsystem_valid) {
+ fwsm = er32(FWSM);
+ factps = er32(FACTPS);
+
+ if (!(factps & E1000_FACTPS_MNGCG) &&
+ ((fwsm & E1000_FWSM_MODE_MASK) ==
+ (e1000_mng_mode_pt << E1000_FWSM_MODE_SHIFT))) {
+ ret_val = 1;
+ return ret_val;
+ }
+ } else {
+ if ((manc & E1000_MANC_SMBUS_EN) &&
+ !(manc & E1000_MANC_ASF_EN)) {
+ ret_val = 1;
+ return ret_val;
+ }
+ }
+
+ return ret_val;
+}
+
+s32 e1000e_read_pba_num(struct e1000_hw *hw, u32 *pba_num)
+{
+ s32 ret_val;
+ u16 nvm_data;
+
+ ret_val = e1000_read_nvm(hw, NVM_PBA_OFFSET_0, 1, &nvm_data);
+ if (ret_val) {
+ hw_dbg(hw, "NVM Read Error\n");
+ return ret_val;
+ }
+ *pba_num = (u32)(nvm_data << 16);
+
+ ret_val = e1000_read_nvm(hw, NVM_PBA_OFFSET_1, 1, &nvm_data);
+ if (ret_val) {
+ hw_dbg(hw, "NVM Read Error\n");
+ return ret_val;
+ }
+ *pba_num |= nvm_data;
+
+ return 0;
+}
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2008 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/vmalloc.h>
+#include <linux/pagemap.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/tcp.h>
+#include <linux/ipv6.h>
+#include <net/checksum.h>
+#include <net/ip6_checksum.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/if_vlan.h>
+#include <linux/cpu.h>
+#include <linux/smp.h>
+
+#include "e1000.h"
+
+#define DRV_VERSION "0.3.3.3-k4"
+char e1000e_driver_name[] = "e1000e";
+const char e1000e_driver_version[] = DRV_VERSION;
+
+static const struct e1000_info *e1000_info_tbl[] = {
+ [board_82571] = &e1000_82571_info,
+ [board_82572] = &e1000_82572_info,
+ [board_82573] = &e1000_82573_info,
+ [board_82574] = &e1000_82574_info,
+ [board_80003es2lan] = &e1000_es2_info,
+ [board_ich8lan] = &e1000_ich8_info,
+ [board_ich9lan] = &e1000_ich9_info,
+ [board_ich10lan] = &e1000_ich10_info,
+};
+
+#ifdef DEBUG
+/**
+ * e1000_get_hw_dev_name - return device name string
+ * used by hardware layer to print debugging information
+ **/
+char *e1000e_get_hw_dev_name(struct e1000_hw *hw)
+{
+ return hw->adapter->netdev->name;
+}
+#endif
+
+/**
+ * e1000_desc_unused - calculate if we have unused descriptors
+ **/
+static int e1000_desc_unused(struct e1000_ring *ring)
+{
+ if (ring->next_to_clean > ring->next_to_use)
+ return ring->next_to_clean - ring->next_to_use - 1;
+
+ return ring->count + ring->next_to_clean - ring->next_to_use - 1;
+}
+
+/**
+ * e1000_receive_skb - helper function to handle Rx indications
+ * @adapter: board private structure
+ * @status: descriptor status field as written by hardware
+ * @vlan: descriptor vlan field as written by hardware (no le/be conversion)
+ * @skb: pointer to sk_buff to be indicated to stack
+ **/
+static void e1000_receive_skb(struct e1000_adapter *adapter,
+ struct net_device *netdev,
+ struct sk_buff *skb,
+ u8 status, __le16 vlan)
+{
+ skb->protocol = eth_type_trans(skb, netdev);
+
+ if (adapter->vlgrp && (status & E1000_RXD_STAT_VP))
+ vlan_hwaccel_receive_skb(skb, adapter->vlgrp,
+ le16_to_cpu(vlan));
+ else
+ netif_receive_skb(skb);
+
+ netdev->last_rx = jiffies;
+}
+
+/**
+ * e1000_rx_checksum - Receive Checksum Offload for 82543
+ * @adapter: board private structure
+ * @status_err: receive descriptor status and error fields
+ * @csum: receive descriptor csum field
+ * @sk_buff: socket buffer with received data
+ **/
+static void e1000_rx_checksum(struct e1000_adapter *adapter, u32 status_err,
+ u32 csum, struct sk_buff *skb)
+{
+ u16 status = (u16)status_err;
+ u8 errors = (u8)(status_err >> 24);
+ skb->ip_summed = CHECKSUM_NONE;
+
+ /* Ignore Checksum bit is set */
+ if (status & E1000_RXD_STAT_IXSM)
+ return;
+ /* TCP/UDP checksum error bit is set */
+ if (errors & E1000_RXD_ERR_TCPE) {
+ /* let the stack verify checksum errors */
+ adapter->hw_csum_err++;
+ return;
+ }
+
+ /* TCP/UDP Checksum has not been calculated */
+ if (!(status & (E1000_RXD_STAT_TCPCS | E1000_RXD_STAT_UDPCS)))
+ return;
+
+ /* It must be a TCP or UDP packet with a valid checksum */
+ if (status & E1000_RXD_STAT_TCPCS) {
+ /* TCP checksum is good */
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
+ } else {
+ /*
+ * IP fragment with UDP payload
+ * Hardware complements the payload checksum, so we undo it
+ * and then put the value in host order for further stack use.
+ */
+ __sum16 sum = (__force __sum16)htons(csum);
+ skb->csum = csum_unfold(~sum);
+ skb->ip_summed = CHECKSUM_COMPLETE;
+ }
+ adapter->hw_csum_good++;
+}
+
+/**
+ * e1000_alloc_rx_buffers - Replace used receive buffers; legacy & extended
+ * @adapter: address of board private structure
+ **/
+static void e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
+ int cleaned_count)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_rx_desc *rx_desc;
+ struct e1000_buffer *buffer_info;
+ struct sk_buff *skb;
+ unsigned int i;
+ unsigned int bufsz = adapter->rx_buffer_len + NET_IP_ALIGN;
+
+ i = rx_ring->next_to_use;
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (cleaned_count--) {
+ skb = buffer_info->skb;
+ if (skb) {
+ skb_trim(skb, 0);
+ goto map_skb;
+ }
+
+ skb = netdev_alloc_skb(netdev, bufsz);
+ if (!skb) {
+ /* Better luck next round */
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+
+ /*
+ * Make buffer alignment 2 beyond a 16 byte boundary
+ * this will result in a 16 byte aligned IP header after
+ * the 14 byte MAC header is removed
+ */
+ skb_reserve(skb, NET_IP_ALIGN);
+
+ buffer_info->skb = skb;
+map_skb:
+ buffer_info->dma = pci_map_single(pdev, skb->data,
+ adapter->rx_buffer_len,
+ PCI_DMA_FROMDEVICE);
+ if (pci_dma_mapping_error(buffer_info->dma)) {
+ dev_err(&pdev->dev, "RX DMA map failed\n");
+ adapter->rx_dma_failed++;
+ break;
+ }
+
+ rx_desc = E1000_RX_DESC(*rx_ring, i);
+ rx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
+
+ i++;
+ if (i == rx_ring->count)
+ i = 0;
+ buffer_info = &rx_ring->buffer_info[i];
+ }
+
+ if (rx_ring->next_to_use != i) {
+ rx_ring->next_to_use = i;
+ if (i-- == 0)
+ i = (rx_ring->count - 1);
+
+ /*
+ * Force memory writes to complete before letting h/w
+ * know there are new descriptors to fetch. (Only
+ * applicable for weak-ordered memory model archs,
+ * such as IA-64).
+ */
+ wmb();
+ writel(i, adapter->hw.hw_addr + rx_ring->tail);
+ }
+}
+
+/**
+ * e1000_alloc_rx_buffers_ps - Replace used receive buffers; packet split
+ * @adapter: address of board private structure
+ **/
+static void e1000_alloc_rx_buffers_ps(struct e1000_adapter *adapter,
+ int cleaned_count)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ union e1000_rx_desc_packet_split *rx_desc;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_buffer *buffer_info;
+ struct e1000_ps_page *ps_page;
+ struct sk_buff *skb;
+ unsigned int i, j;
+
+ i = rx_ring->next_to_use;
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (cleaned_count--) {
+ rx_desc = E1000_RX_DESC_PS(*rx_ring, i);
+
+ for (j = 0; j < PS_PAGE_BUFFERS; j++) {
+ ps_page = &buffer_info->ps_pages[j];
+ if (j >= adapter->rx_ps_pages) {
+ /* all unused desc entries get hw null ptr */
+ rx_desc->read.buffer_addr[j+1] = ~cpu_to_le64(0);
+ continue;
+ }
+ if (!ps_page->page) {
+ ps_page->page = alloc_page(GFP_ATOMIC);
+ if (!ps_page->page) {
+ adapter->alloc_rx_buff_failed++;
+ goto no_buffers;
+ }
+ ps_page->dma = pci_map_page(pdev,
+ ps_page->page,
+ 0, PAGE_SIZE,
+ PCI_DMA_FROMDEVICE);
+ if (pci_dma_mapping_error(ps_page->dma)) {
+ dev_err(&adapter->pdev->dev,
+ "RX DMA page map failed\n");
+ adapter->rx_dma_failed++;
+ goto no_buffers;
+ }
+ }
+ /*
+ * Refresh the desc even if buffer_addrs
+ * didn't change because each write-back
+ * erases this info.
+ */
+ rx_desc->read.buffer_addr[j+1] =
+ cpu_to_le64(ps_page->dma);
+ }
+
+ skb = netdev_alloc_skb(netdev,
+ adapter->rx_ps_bsize0 + NET_IP_ALIGN);
+
+ if (!skb) {
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+
+ /*
+ * Make buffer alignment 2 beyond a 16 byte boundary
+ * this will result in a 16 byte aligned IP header after
+ * the 14 byte MAC header is removed
+ */
+ skb_reserve(skb, NET_IP_ALIGN);
+
+ buffer_info->skb = skb;
+ buffer_info->dma = pci_map_single(pdev, skb->data,
+ adapter->rx_ps_bsize0,
+ PCI_DMA_FROMDEVICE);
+ if (pci_dma_mapping_error(buffer_info->dma)) {
+ dev_err(&pdev->dev, "RX DMA map failed\n");
+ adapter->rx_dma_failed++;
+ /* cleanup skb */
+ dev_kfree_skb_any(skb);
+ buffer_info->skb = NULL;
+ break;
+ }
+
+ rx_desc->read.buffer_addr[0] = cpu_to_le64(buffer_info->dma);
+
+ i++;
+ if (i == rx_ring->count)
+ i = 0;
+ buffer_info = &rx_ring->buffer_info[i];
+ }
+
+no_buffers:
+ if (rx_ring->next_to_use != i) {
+ rx_ring->next_to_use = i;
+
+ if (!(i--))
+ i = (rx_ring->count - 1);
+
+ /*
+ * Force memory writes to complete before letting h/w
+ * know there are new descriptors to fetch. (Only
+ * applicable for weak-ordered memory model archs,
+ * such as IA-64).
+ */
+ wmb();
+ /*
+ * Hardware increments by 16 bytes, but packet split
+ * descriptors are 32 bytes...so we increment tail
+ * twice as much.
+ */
+ writel(i<<1, adapter->hw.hw_addr + rx_ring->tail);
+ }
+}
+
+/**
+ * e1000_alloc_jumbo_rx_buffers - Replace used jumbo receive buffers
+ * @adapter: address of board private structure
+ * @rx_ring: pointer to receive ring structure
+ * @cleaned_count: number of buffers to allocate this pass
+ **/
+
+static void e1000_alloc_jumbo_rx_buffers(struct e1000_adapter *adapter,
+ int cleaned_count)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_rx_desc *rx_desc;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_buffer *buffer_info;
+ struct sk_buff *skb;
+ unsigned int i;
+ unsigned int bufsz = 256 -
+ 16 /* for skb_reserve */ -
+ NET_IP_ALIGN;
+
+ i = rx_ring->next_to_use;
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (cleaned_count--) {
+ skb = buffer_info->skb;
+ if (skb) {
+ skb_trim(skb, 0);
+ goto check_page;
+ }
+
+ skb = netdev_alloc_skb(netdev, bufsz);
+ if (unlikely(!skb)) {
+ /* Better luck next round */
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+
+ /* Make buffer alignment 2 beyond a 16 byte boundary
+ * this will result in a 16 byte aligned IP header after
+ * the 14 byte MAC header is removed
+ */
+ skb_reserve(skb, NET_IP_ALIGN);
+
+ buffer_info->skb = skb;
+check_page:
+ /* allocate a new page if necessary */
+ if (!buffer_info->page) {
+ buffer_info->page = alloc_page(GFP_ATOMIC);
+ if (unlikely(!buffer_info->page)) {
+ adapter->alloc_rx_buff_failed++;
+ break;
+ }
+ }
+
+ if (!buffer_info->dma)
+ buffer_info->dma = pci_map_page(pdev,
+ buffer_info->page, 0,
+ PAGE_SIZE,
+ PCI_DMA_FROMDEVICE);
+
+ rx_desc = E1000_RX_DESC(*rx_ring, i);
+ rx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
+
+ if (unlikely(++i == rx_ring->count))
+ i = 0;
+ buffer_info = &rx_ring->buffer_info[i];
+ }
+
+ if (likely(rx_ring->next_to_use != i)) {
+ rx_ring->next_to_use = i;
+ if (unlikely(i-- == 0))
+ i = (rx_ring->count - 1);
+
+ /* Force memory writes to complete before letting h/w
+ * know there are new descriptors to fetch. (Only
+ * applicable for weak-ordered memory model archs,
+ * such as IA-64). */
+ wmb();
+ writel(i, adapter->hw.hw_addr + rx_ring->tail);
+ }
+}
+
+/**
+ * e1000_clean_rx_irq - Send received data up the network stack; legacy
+ * @adapter: board private structure
+ *
+ * the return value indicates whether actual cleaning was done, there
+ * is no guarantee that everything was cleaned
+ **/
+static bool e1000_clean_rx_irq(struct e1000_adapter *adapter,
+ int *work_done, int work_to_do)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_rx_desc *rx_desc, *next_rxd;
+ struct e1000_buffer *buffer_info, *next_buffer;
+ u32 length;
+ unsigned int i;
+ int cleaned_count = 0;
+ bool cleaned = 0;
+ unsigned int total_rx_bytes = 0, total_rx_packets = 0;
+
+ i = rx_ring->next_to_clean;
+ rx_desc = E1000_RX_DESC(*rx_ring, i);
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (rx_desc->status & E1000_RXD_STAT_DD) {
+ struct sk_buff *skb;
+ u8 status;
+
+ if (*work_done >= work_to_do)
+ break;
+ (*work_done)++;
+
+ status = rx_desc->status;
+ skb = buffer_info->skb;
+ buffer_info->skb = NULL;
+
+ prefetch(skb->data - NET_IP_ALIGN);
+
+ i++;
+ if (i == rx_ring->count)
+ i = 0;
+ next_rxd = E1000_RX_DESC(*rx_ring, i);
+ prefetch(next_rxd);
+
+ next_buffer = &rx_ring->buffer_info[i];
+
+ cleaned = 1;
+ cleaned_count++;
+ pci_unmap_single(pdev,
+ buffer_info->dma,
+ adapter->rx_buffer_len,
+ PCI_DMA_FROMDEVICE);
+ buffer_info->dma = 0;
+
+ length = le16_to_cpu(rx_desc->length);
+
+ /* !EOP means multiple descriptors were used to store a single
+ * packet, also make sure the frame isn't just CRC only */
+ if (!(status & E1000_RXD_STAT_EOP) || (length <= 4)) {
+ /* All receives must fit into a single buffer */
+ e_dbg("%s: Receive packet consumed multiple buffers\n",
+ netdev->name);
+ /* recycle */
+ buffer_info->skb = skb;
+ goto next_desc;
+ }
+
+ if (rx_desc->errors & E1000_RXD_ERR_FRAME_ERR_MASK) {
+ /* recycle */
+ buffer_info->skb = skb;
+ goto next_desc;
+ }
+
+ total_rx_bytes += length;
+ total_rx_packets++;
+
+ /*
+ * code added for copybreak, this should improve
+ * performance for small packets with large amounts
+ * of reassembly being done in the stack
+ */
+ if (length < copybreak) {
+ struct sk_buff *new_skb =
+ netdev_alloc_skb(netdev, length + NET_IP_ALIGN);
+ if (new_skb) {
+ skb_reserve(new_skb, NET_IP_ALIGN);
+ skb_copy_to_linear_data_offset(new_skb,
+ -NET_IP_ALIGN,
+ (skb->data -
+ NET_IP_ALIGN),
+ (length +
+ NET_IP_ALIGN));
+ /* save the skb in buffer_info as good */
+ buffer_info->skb = skb;
+ skb = new_skb;
+ }
+ /* else just continue with the old one */
+ }
+ /* end copybreak code */
+ skb_put(skb, length);
+
+ /* Receive Checksum Offload */
+ e1000_rx_checksum(adapter,
+ (u32)(status) |
+ ((u32)(rx_desc->errors) << 24),
+ le16_to_cpu(rx_desc->csum), skb);
+
+ e1000_receive_skb(adapter, netdev, skb,status,rx_desc->special);
+
+next_desc:
+ rx_desc->status = 0;
+
+ /* return some buffers to hardware, one at a time is too slow */
+ if (cleaned_count >= E1000_RX_BUFFER_WRITE) {
+ adapter->alloc_rx_buf(adapter, cleaned_count);
+ cleaned_count = 0;
+ }
+
+ /* use prefetched values */
+ rx_desc = next_rxd;
+ buffer_info = next_buffer;
+ }
+ rx_ring->next_to_clean = i;
+
+ cleaned_count = e1000_desc_unused(rx_ring);
+ if (cleaned_count)
+ adapter->alloc_rx_buf(adapter, cleaned_count);
+
+ adapter->total_rx_bytes += total_rx_bytes;
+ adapter->total_rx_packets += total_rx_packets;
+ adapter->net_stats.rx_bytes += total_rx_bytes;
+ adapter->net_stats.rx_packets += total_rx_packets;
+ return cleaned;
+}
+
+static void e1000_put_txbuf(struct e1000_adapter *adapter,
+ struct e1000_buffer *buffer_info)
+{
+ if (buffer_info->dma) {
+ pci_unmap_page(adapter->pdev, buffer_info->dma,
+ buffer_info->length, PCI_DMA_TODEVICE);
+ buffer_info->dma = 0;
+ }
+ if (buffer_info->skb) {
+ dev_kfree_skb_any(buffer_info->skb);
+ buffer_info->skb = NULL;
+ }
+}
+
+static void e1000_print_tx_hang(struct e1000_adapter *adapter)
+{
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ unsigned int i = tx_ring->next_to_clean;
+ unsigned int eop = tx_ring->buffer_info[i].next_to_watch;
+ struct e1000_tx_desc *eop_desc = E1000_TX_DESC(*tx_ring, eop);
+
+ /* detected Tx unit hang */
+ e_err("Detected Tx Unit Hang:\n"
+ " TDH <%x>\n"
+ " TDT <%x>\n"
+ " next_to_use <%x>\n"
+ " next_to_clean <%x>\n"
+ "buffer_info[next_to_clean]:\n"
+ " time_stamp <%lx>\n"
+ " next_to_watch <%x>\n"
+ " jiffies <%lx>\n"
+ " next_to_watch.status <%x>\n",
+ readl(adapter->hw.hw_addr + tx_ring->head),
+ readl(adapter->hw.hw_addr + tx_ring->tail),
+ tx_ring->next_to_use,
+ tx_ring->next_to_clean,
+ tx_ring->buffer_info[eop].time_stamp,
+ eop,
+ jiffies,
+ eop_desc->upper.fields.status);
+}
+
+/**
+ * e1000_clean_tx_irq - Reclaim resources after transmit completes
+ * @adapter: board private structure
+ *
+ * the return value indicates whether actual cleaning was done, there
+ * is no guarantee that everything was cleaned
+ **/
+static bool e1000_clean_tx_irq(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ struct e1000_tx_desc *tx_desc, *eop_desc;
+ struct e1000_buffer *buffer_info;
+ unsigned int i, eop;
+ unsigned int count = 0;
+ bool cleaned = 0;
+ unsigned int total_tx_bytes = 0, total_tx_packets = 0;
+
+ i = tx_ring->next_to_clean;
+ eop = tx_ring->buffer_info[i].next_to_watch;
+ eop_desc = E1000_TX_DESC(*tx_ring, eop);
+
+ while (eop_desc->upper.data & cpu_to_le32(E1000_TXD_STAT_DD)) {
+ for (cleaned = 0; !cleaned; ) {
+ tx_desc = E1000_TX_DESC(*tx_ring, i);
+ buffer_info = &tx_ring->buffer_info[i];
+ cleaned = (i == eop);
+
+ if (cleaned) {
+ struct sk_buff *skb = buffer_info->skb;
+ unsigned int segs, bytecount;
+ segs = skb_shinfo(skb)->gso_segs ?: 1;
+ /* multiply data chunks by size of headers */
+ bytecount = ((segs - 1) * skb_headlen(skb)) +
+ skb->len;
+ total_tx_packets += segs;
+ total_tx_bytes += bytecount;
+ }
+
+ e1000_put_txbuf(adapter, buffer_info);
+ tx_desc->upper.data = 0;
+
+ i++;
+ if (i == tx_ring->count)
+ i = 0;
+ }
+
+ eop = tx_ring->buffer_info[i].next_to_watch;
+ eop_desc = E1000_TX_DESC(*tx_ring, eop);
+#define E1000_TX_WEIGHT 64
+ /* weight of a sort for tx, to avoid endless transmit cleanup */
+ if (count++ == E1000_TX_WEIGHT)
+ break;
+ }
+
+ tx_ring->next_to_clean = i;
+
+#define TX_WAKE_THRESHOLD 32
+ if (cleaned && netif_carrier_ok(netdev) &&
+ e1000_desc_unused(tx_ring) >= TX_WAKE_THRESHOLD) {
+ /* Make sure that anybody stopping the queue after this
+ * sees the new next_to_clean.
+ */
+ smp_mb();
+
+ if (netif_queue_stopped(netdev) &&
+ !(test_bit(__E1000_DOWN, &adapter->state))) {
+ netif_wake_queue(netdev);
+ ++adapter->restart_queue;
+ }
+ }
+
+ if (adapter->detect_tx_hung) {
+ /*
+ * Detect a transmit hang in hardware, this serializes the
+ * check with the clearing of time_stamp and movement of i
+ */
+ adapter->detect_tx_hung = 0;
+ if (tx_ring->buffer_info[eop].dma &&
+ time_after(jiffies, tx_ring->buffer_info[eop].time_stamp
+ + (adapter->tx_timeout_factor * HZ))
+ && !(er32(STATUS) & E1000_STATUS_TXOFF)) {
+ e1000_print_tx_hang(adapter);
+ netif_stop_queue(netdev);
+ }
+ }
+ adapter->total_tx_bytes += total_tx_bytes;
+ adapter->total_tx_packets += total_tx_packets;
+ adapter->net_stats.tx_bytes += total_tx_bytes;
+ adapter->net_stats.tx_packets += total_tx_packets;
+ return cleaned;
+}
+
+/**
+ * e1000_clean_rx_irq_ps - Send received data up the network stack; packet split
+ * @adapter: board private structure
+ *
+ * the return value indicates whether actual cleaning was done, there
+ * is no guarantee that everything was cleaned
+ **/
+static bool e1000_clean_rx_irq_ps(struct e1000_adapter *adapter,
+ int *work_done, int work_to_do)
+{
+ union e1000_rx_desc_packet_split *rx_desc, *next_rxd;
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_buffer *buffer_info, *next_buffer;
+ struct e1000_ps_page *ps_page;
+ struct sk_buff *skb;
+ unsigned int i, j;
+ u32 length, staterr;
+ int cleaned_count = 0;
+ bool cleaned = 0;
+ unsigned int total_rx_bytes = 0, total_rx_packets = 0;
+
+ i = rx_ring->next_to_clean;
+ rx_desc = E1000_RX_DESC_PS(*rx_ring, i);
+ staterr = le32_to_cpu(rx_desc->wb.middle.status_error);
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (staterr & E1000_RXD_STAT_DD) {
+ if (*work_done >= work_to_do)
+ break;
+ (*work_done)++;
+ skb = buffer_info->skb;
+
+ /* in the packet split case this is header only */
+ prefetch(skb->data - NET_IP_ALIGN);
+
+ i++;
+ if (i == rx_ring->count)
+ i = 0;
+ next_rxd = E1000_RX_DESC_PS(*rx_ring, i);
+ prefetch(next_rxd);
+
+ next_buffer = &rx_ring->buffer_info[i];
+
+ cleaned = 1;
+ cleaned_count++;
+ pci_unmap_single(pdev, buffer_info->dma,
+ adapter->rx_ps_bsize0,
+ PCI_DMA_FROMDEVICE);
+ buffer_info->dma = 0;
+
+ if (!(staterr & E1000_RXD_STAT_EOP)) {
+ e_dbg("%s: Packet Split buffers didn't pick up the "
+ "full packet\n", netdev->name);
+ dev_kfree_skb_irq(skb);
+ goto next_desc;
+ }
+
+ if (staterr & E1000_RXDEXT_ERR_FRAME_ERR_MASK) {
+ dev_kfree_skb_irq(skb);
+ goto next_desc;
+ }
+
+ length = le16_to_cpu(rx_desc->wb.middle.length0);
+
+ if (!length) {
+ e_dbg("%s: Last part of the packet spanning multiple "
+ "descriptors\n", netdev->name);
+ dev_kfree_skb_irq(skb);
+ goto next_desc;
+ }
+
+ /* Good Receive */
+ skb_put(skb, length);
+
+ {
+ /*
+ * this looks ugly, but it seems compiler issues make it
+ * more efficient than reusing j
+ */
+ int l1 = le16_to_cpu(rx_desc->wb.upper.length[0]);
+
+ /*
+ * page alloc/put takes too long and effects small packet
+ * throughput, so unsplit small packets and save the alloc/put
+ * only valid in softirq (napi) context to call kmap_*
+ */
+ if (l1 && (l1 <= copybreak) &&
+ ((length + l1) <= adapter->rx_ps_bsize0)) {
+ u8 *vaddr;
+
+ ps_page = &buffer_info->ps_pages[0];
+
+ /*
+ * there is no documentation about how to call
+ * kmap_atomic, so we can't hold the mapping
+ * very long
+ */
+ pci_dma_sync_single_for_cpu(pdev, ps_page->dma,
+ PAGE_SIZE, PCI_DMA_FROMDEVICE);
+ vaddr = kmap_atomic(ps_page->page, KM_SKB_DATA_SOFTIRQ);
+ memcpy(skb_tail_pointer(skb), vaddr, l1);
+ kunmap_atomic(vaddr, KM_SKB_DATA_SOFTIRQ);
+ pci_dma_sync_single_for_device(pdev, ps_page->dma,
+ PAGE_SIZE, PCI_DMA_FROMDEVICE);
+
+ skb_put(skb, l1);
+ goto copydone;
+ } /* if */
+ }
+
+ for (j = 0; j < PS_PAGE_BUFFERS; j++) {
+ length = le16_to_cpu(rx_desc->wb.upper.length[j]);
+ if (!length)
+ break;
+
+ ps_page = &buffer_info->ps_pages[j];
+ pci_unmap_page(pdev, ps_page->dma, PAGE_SIZE,
+ PCI_DMA_FROMDEVICE);
+ ps_page->dma = 0;
+ skb_fill_page_desc(skb, j, ps_page->page, 0, length);
+ ps_page->page = NULL;
+ skb->len += length;
+ skb->data_len += length;
+ skb->truesize += length;
+ }
+
+copydone:
+ total_rx_bytes += skb->len;
+ total_rx_packets++;
+
+ e1000_rx_checksum(adapter, staterr, le16_to_cpu(
+ rx_desc->wb.lower.hi_dword.csum_ip.csum), skb);
+
+ if (rx_desc->wb.upper.header_status &
+ cpu_to_le16(E1000_RXDPS_HDRSTAT_HDRSP))
+ adapter->rx_hdr_split++;
+
+ e1000_receive_skb(adapter, netdev, skb,
+ staterr, rx_desc->wb.middle.vlan);
+
+next_desc:
+ rx_desc->wb.middle.status_error &= cpu_to_le32(~0xFF);
+ buffer_info->skb = NULL;
+
+ /* return some buffers to hardware, one at a time is too slow */
+ if (cleaned_count >= E1000_RX_BUFFER_WRITE) {
+ adapter->alloc_rx_buf(adapter, cleaned_count);
+ cleaned_count = 0;
+ }
+
+ /* use prefetched values */
+ rx_desc = next_rxd;
+ buffer_info = next_buffer;
+
+ staterr = le32_to_cpu(rx_desc->wb.middle.status_error);
+ }
+ rx_ring->next_to_clean = i;
+
+ cleaned_count = e1000_desc_unused(rx_ring);
+ if (cleaned_count)
+ adapter->alloc_rx_buf(adapter, cleaned_count);
+
+ adapter->total_rx_bytes += total_rx_bytes;
+ adapter->total_rx_packets += total_rx_packets;
+ adapter->net_stats.rx_bytes += total_rx_bytes;
+ adapter->net_stats.rx_packets += total_rx_packets;
+ return cleaned;
+}
+
+/**
+ * e1000_consume_page - helper function
+ **/
+static void e1000_consume_page(struct e1000_buffer *bi, struct sk_buff *skb,
+ u16 length)
+{
+ bi->page = NULL;
+ skb->len += length;
+ skb->data_len += length;
+ skb->truesize += length;
+}
+
+/**
+ * e1000_clean_jumbo_rx_irq - Send received data up the network stack; legacy
+ * @adapter: board private structure
+ *
+ * the return value indicates whether actual cleaning was done, there
+ * is no guarantee that everything was cleaned
+ **/
+
+static bool e1000_clean_jumbo_rx_irq(struct e1000_adapter *adapter,
+ int *work_done, int work_to_do)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_rx_desc *rx_desc, *next_rxd;
+ struct e1000_buffer *buffer_info, *next_buffer;
+ u32 length;
+ unsigned int i;
+ int cleaned_count = 0;
+ bool cleaned = false;
+ unsigned int total_rx_bytes=0, total_rx_packets=0;
+
+ i = rx_ring->next_to_clean;
+ rx_desc = E1000_RX_DESC(*rx_ring, i);
+ buffer_info = &rx_ring->buffer_info[i];
+
+ while (rx_desc->status & E1000_RXD_STAT_DD) {
+ struct sk_buff *skb;
+ u8 status;
+
+ if (*work_done >= work_to_do)
+ break;
+ (*work_done)++;
+
+ status = rx_desc->status;
+ skb = buffer_info->skb;
+ buffer_info->skb = NULL;
+
+ ++i;
+ if (i == rx_ring->count)
+ i = 0;
+ next_rxd = E1000_RX_DESC(*rx_ring, i);
+ prefetch(next_rxd);
+
+ next_buffer = &rx_ring->buffer_info[i];
+
+ cleaned = true;
+ cleaned_count++;
+ pci_unmap_page(pdev, buffer_info->dma, PAGE_SIZE,
+ PCI_DMA_FROMDEVICE);
+ buffer_info->dma = 0;
+
+ length = le16_to_cpu(rx_desc->length);
+
+ /* errors is only valid for DD + EOP descriptors */
+ if (unlikely((status & E1000_RXD_STAT_EOP) &&
+ (rx_desc->errors & E1000_RXD_ERR_FRAME_ERR_MASK))) {
+ /* recycle both page and skb */
+ buffer_info->skb = skb;
+ /* an error means any chain goes out the window
+ * too */
+ if (rx_ring->rx_skb_top)
+ dev_kfree_skb(rx_ring->rx_skb_top);
+ rx_ring->rx_skb_top = NULL;
+ goto next_desc;
+ }
+
+#define rxtop rx_ring->rx_skb_top
+ if (!(status & E1000_RXD_STAT_EOP)) {
+ /* this descriptor is only the beginning (or middle) */
+ if (!rxtop) {
+ /* this is the beginning of a chain */
+ rxtop = skb;
+ skb_fill_page_desc(rxtop, 0, buffer_info->page,
+ 0, length);
+ } else {
+ /* this is the middle of a chain */
+ skb_fill_page_desc(rxtop,
+ skb_shinfo(rxtop)->nr_frags,
+ buffer_info->page, 0, length);
+ /* re-use the skb, only consumed the page */
+ buffer_info->skb = skb;
+ }
+ e1000_consume_page(buffer_info, rxtop, length);
+ goto next_desc;
+ } else {
+ if (rxtop) {
+ /* end of the chain */
+ skb_fill_page_desc(rxtop,
+ skb_shinfo(rxtop)->nr_frags,
+ buffer_info->page, 0, length);
+ /* re-use the current skb, we only consumed the
+ * page */
+ buffer_info->skb = skb;
+ skb = rxtop;
+ rxtop = NULL;
+ e1000_consume_page(buffer_info, skb, length);
+ } else {
+ /* no chain, got EOP, this buf is the packet
+ * copybreak to save the put_page/alloc_page */
+ if (length <= copybreak &&
+ skb_tailroom(skb) >= length) {
+ u8 *vaddr;
+ vaddr = kmap_atomic(buffer_info->page,
+ KM_SKB_DATA_SOFTIRQ);
+ memcpy(skb_tail_pointer(skb), vaddr,
+ length);
+ kunmap_atomic(vaddr,
+ KM_SKB_DATA_SOFTIRQ);
+ /* re-use the page, so don't erase
+ * buffer_info->page */
+ skb_put(skb, length);
+ } else {
+ skb_fill_page_desc(skb, 0,
+ buffer_info->page, 0,
+ length);
+ e1000_consume_page(buffer_info, skb,
+ length);
+ }
+ }
+ }
+
+ /* Receive Checksum Offload XXX recompute due to CRC strip? */
+ e1000_rx_checksum(adapter,
+ (u32)(status) |
+ ((u32)(rx_desc->errors) << 24),
+ le16_to_cpu(rx_desc->csum), skb);
+
+ /* probably a little skewed due to removing CRC */
+ total_rx_bytes += skb->len;
+ total_rx_packets++;
+
+ /* eth type trans needs skb->data to point to something */
+ if (!pskb_may_pull(skb, ETH_HLEN)) {
+ e_err("pskb_may_pull failed.\n");
+ dev_kfree_skb(skb);
+ goto next_desc;
+ }
+
+ e1000_receive_skb(adapter, netdev, skb, status,
+ rx_desc->special);
+
+next_desc:
+ rx_desc->status = 0;
+
+ /* return some buffers to hardware, one at a time is too slow */
+ if (unlikely(cleaned_count >= E1000_RX_BUFFER_WRITE)) {
+ adapter->alloc_rx_buf(adapter, cleaned_count);
+ cleaned_count = 0;
+ }
+
+ /* use prefetched values */
+ rx_desc = next_rxd;
+ buffer_info = next_buffer;
+ }
+ rx_ring->next_to_clean = i;
+
+ cleaned_count = e1000_desc_unused(rx_ring);
+ if (cleaned_count)
+ adapter->alloc_rx_buf(adapter, cleaned_count);
+
+ adapter->total_rx_bytes += total_rx_bytes;
+ adapter->total_rx_packets += total_rx_packets;
+ adapter->net_stats.rx_bytes += total_rx_bytes;
+ adapter->net_stats.rx_packets += total_rx_packets;
+ return cleaned;
+}
+
+/**
+ * e1000_clean_rx_ring - Free Rx Buffers per Queue
+ * @adapter: board private structure
+ **/
+static void e1000_clean_rx_ring(struct e1000_adapter *adapter)
+{
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_buffer *buffer_info;
+ struct e1000_ps_page *ps_page;
+ struct pci_dev *pdev = adapter->pdev;
+ unsigned int i, j;
+
+ /* Free all the Rx ring sk_buffs */
+ for (i = 0; i < rx_ring->count; i++) {
+ buffer_info = &rx_ring->buffer_info[i];
+ if (buffer_info->dma) {
+ if (adapter->clean_rx == e1000_clean_rx_irq)
+ pci_unmap_single(pdev, buffer_info->dma,
+ adapter->rx_buffer_len,
+ PCI_DMA_FROMDEVICE);
+ else if (adapter->clean_rx == e1000_clean_jumbo_rx_irq)
+ pci_unmap_page(pdev, buffer_info->dma,
+ PAGE_SIZE,
+ PCI_DMA_FROMDEVICE);
+ else if (adapter->clean_rx == e1000_clean_rx_irq_ps)
+ pci_unmap_single(pdev, buffer_info->dma,
+ adapter->rx_ps_bsize0,
+ PCI_DMA_FROMDEVICE);
+ buffer_info->dma = 0;
+ }
+
+ if (buffer_info->page) {
+ put_page(buffer_info->page);
+ buffer_info->page = NULL;
+ }
+
+ if (buffer_info->skb) {
+ dev_kfree_skb(buffer_info->skb);
+ buffer_info->skb = NULL;
+ }
+
+ for (j = 0; j < PS_PAGE_BUFFERS; j++) {
+ ps_page = &buffer_info->ps_pages[j];
+ if (!ps_page->page)
+ break;
+ pci_unmap_page(pdev, ps_page->dma, PAGE_SIZE,
+ PCI_DMA_FROMDEVICE);
+ ps_page->dma = 0;
+ put_page(ps_page->page);
+ ps_page->page = NULL;
+ }
+ }
+
+ /* there also may be some cached data from a chained receive */
+ if (rx_ring->rx_skb_top) {
+ dev_kfree_skb(rx_ring->rx_skb_top);
+ rx_ring->rx_skb_top = NULL;
+ }
+
+ /* Zero out the descriptor ring */
+ memset(rx_ring->desc, 0, rx_ring->size);
+
+ rx_ring->next_to_clean = 0;
+ rx_ring->next_to_use = 0;
+
+ writel(0, adapter->hw.hw_addr + rx_ring->head);
+ writel(0, adapter->hw.hw_addr + rx_ring->tail);
+}
+
+/**
+ * e1000_intr_msi - Interrupt Handler
+ * @irq: interrupt number
+ * @data: pointer to a network interface device structure
+ **/
+static irqreturn_t e1000_intr_msi(int irq, void *data, struct pt_regs *regs)
+{
+ struct net_device *netdev = data;
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 icr = er32(ICR);
+
+ /*
+ * read ICR disables interrupts using IAM
+ */
+
+ if (icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC)) {
+ hw->mac.get_link_status = 1;
+ /*
+ * ICH8 workaround-- Call gig speed drop workaround on cable
+ * disconnect (LSC) before accessing any PHY registers
+ */
+ if ((adapter->flags & FLAG_LSC_GIG_SPEED_DROP) &&
+ (!(er32(STATUS) & E1000_STATUS_LU)))
+ e1000e_gig_downshift_workaround_ich8lan(hw);
+
+ /*
+ * 80003ES2LAN workaround-- For packet buffer work-around on
+ * link down event; disable receives here in the ISR and reset
+ * adapter in watchdog
+ */
+ if (netif_carrier_ok(netdev) &&
+ adapter->flags & FLAG_RX_NEEDS_RESTART) {
+ /* disable receives */
+ u32 rctl = er32(RCTL);
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
+ adapter->flags |= FLAG_RX_RESTART_NOW;
+ }
+ /* guard against interrupt when we're going down */
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ mod_timer(&adapter->watchdog_timer, jiffies + 1);
+ }
+
+ if (netif_rx_schedule_prep(netdev)) {
+ adapter->total_tx_bytes = 0;
+ adapter->total_tx_packets = 0;
+ adapter->total_rx_bytes = 0;
+ adapter->total_rx_packets = 0;
+ __netif_rx_schedule(netdev);
+ }
+
+ return IRQ_HANDLED;
+}
+
+/**
+ * e1000_intr - Interrupt Handler
+ * @irq: interrupt number
+ * @data: pointer to a network interface device structure
+ **/
+static irqreturn_t e1000_intr(int irq, void *data, struct pt_regs *regs)
+{
+ struct net_device *netdev = data;
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 rctl, icr = er32(ICR);
+
+ if (!icr)
+ return IRQ_NONE; /* Not our interrupt */
+
+ /*
+ * IMS will not auto-mask if INT_ASSERTED is not set, and if it is
+ * not set, then the adapter didn't send an interrupt
+ */
+ if (!(icr & E1000_ICR_INT_ASSERTED))
+ return IRQ_NONE;
+
+ /*
+ * Interrupt Auto-Mask...upon reading ICR,
+ * interrupts are masked. No need for the
+ * IMC write
+ */
+
+ if (icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC)) {
+ hw->mac.get_link_status = 1;
+ /*
+ * ICH8 workaround-- Call gig speed drop workaround on cable
+ * disconnect (LSC) before accessing any PHY registers
+ */
+ if ((adapter->flags & FLAG_LSC_GIG_SPEED_DROP) &&
+ (!(er32(STATUS) & E1000_STATUS_LU)))
+ e1000e_gig_downshift_workaround_ich8lan(hw);
+
+ /*
+ * 80003ES2LAN workaround--
+ * For packet buffer work-around on link down event;
+ * disable receives here in the ISR and
+ * reset adapter in watchdog
+ */
+ if (netif_carrier_ok(netdev) &&
+ (adapter->flags & FLAG_RX_NEEDS_RESTART)) {
+ /* disable receives */
+ rctl = er32(RCTL);
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
+ adapter->flags |= FLAG_RX_RESTART_NOW;
+ }
+ /* guard against interrupt when we're going down */
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ mod_timer(&adapter->watchdog_timer, jiffies + 1);
+ }
+
+ if (netif_rx_schedule_prep(netdev)) {
+ adapter->total_tx_bytes = 0;
+ adapter->total_tx_packets = 0;
+ adapter->total_rx_bytes = 0;
+ adapter->total_rx_packets = 0;
+ __netif_rx_schedule(netdev);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t e1000_msix_other(int irq, void *data, struct pt_regs *regs)
+{
+ struct net_device *netdev = data;
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 icr = er32(ICR);
+
+ if (!(icr & E1000_ICR_INT_ASSERTED)) {
+ ew32(IMS, E1000_IMS_OTHER);
+ return IRQ_NONE;
+ }
+
+ if (icr & adapter->eiac_mask)
+ ew32(ICS, (icr & adapter->eiac_mask));
+
+ if (icr & E1000_ICR_OTHER) {
+ if (!(icr & E1000_ICR_LSC))
+ goto no_link_interrupt;
+ hw->mac.get_link_status = 1;
+ /* guard against interrupt when we're going down */
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ mod_timer(&adapter->watchdog_timer, jiffies + 1);
+ }
+
+no_link_interrupt:
+ ew32(IMS, E1000_IMS_LSC | E1000_IMS_OTHER);
+
+ return IRQ_HANDLED;
+}
+
+
+static irqreturn_t e1000_intr_msix_tx(int irq, void *data, struct pt_regs *regs)
+{
+ struct net_device *netdev = data;
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+
+
+ adapter->total_tx_bytes = 0;
+ adapter->total_tx_packets = 0;
+
+ if (!e1000_clean_tx_irq(adapter))
+ /* Ring was not completely cleaned, so fire another interrupt */
+ ew32(ICS, tx_ring->ims_val);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t e1000_intr_msix_rx(int irq, void *data, struct pt_regs *regs)
+{
+ struct net_device *netdev = data;
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ /* Write the ITR value calculated at the end of the
+ * previous interrupt.
+ */
+ if (adapter->rx_ring->set_itr) {
+ writel(1000000000 / (adapter->rx_ring->itr_val * 256),
+ adapter->hw.hw_addr + adapter->rx_ring->itr_register);
+ adapter->rx_ring->set_itr = 0;
+ }
+
+ if (netif_rx_schedule_prep(netdev)) {
+ adapter->total_rx_bytes = 0;
+ adapter->total_rx_packets = 0;
+ __netif_rx_schedule(netdev);
+ }
+ return IRQ_HANDLED;
+}
+
+/**
+ * e1000_configure_msix - Configure MSI-X hardware
+ *
+ * e1000_configure_msix sets up the hardware to properly
+ * generate MSI-X interrupts.
+ **/
+static void e1000_configure_msix(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ int vector = 0;
+ u32 ctrl_ext, ivar = 0;
+
+ adapter->eiac_mask = 0;
+
+ /* Workaround issue with spurious interrupts on 82574 in MSI-X mode */
+ if (hw->mac.type == e1000_82574) {
+ u32 rfctl = er32(RFCTL);
+ rfctl |= E1000_RFCTL_ACK_DIS;
+ ew32(RFCTL, rfctl);
+ }
+
+#define E1000_IVAR_INT_ALLOC_VALID 0x8
+ /* Configure Rx vector */
+ rx_ring->ims_val = E1000_IMS_RXQ0;
+ adapter->eiac_mask |= rx_ring->ims_val;
+ if (rx_ring->itr_val)
+ writel(1000000000 / (rx_ring->itr_val * 256),
+ hw->hw_addr + rx_ring->itr_register);
+ else
+ writel(1, hw->hw_addr + rx_ring->itr_register);
+ ivar = E1000_IVAR_INT_ALLOC_VALID | vector;
+
+ /* Configure Tx vector */
+ tx_ring->ims_val = E1000_IMS_TXQ0;
+ vector++;
+ if (tx_ring->itr_val)
+ writel(1000000000 / (tx_ring->itr_val * 256),
+ hw->hw_addr + tx_ring->itr_register);
+ else
+ writel(1, hw->hw_addr + tx_ring->itr_register);
+ adapter->eiac_mask |= tx_ring->ims_val;
+ ivar |= ((E1000_IVAR_INT_ALLOC_VALID | vector) << 8);
+
+ /* set vector for Other Causes, e.g. link changes */
+ vector++;
+ ivar |= ((E1000_IVAR_INT_ALLOC_VALID | vector) << 16);
+ if (rx_ring->itr_val)
+ writel(1000000000 / (rx_ring->itr_val * 256),
+ hw->hw_addr + E1000_EITR_82574(vector));
+ else
+ writel(1, hw->hw_addr + E1000_EITR_82574(vector));
+
+ /* Cause Tx interrupts on every write back */
+ ivar |= (1 << 31);
+
+ ew32(IVAR, ivar);
+
+ /* enable MSI-X PBA support */
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_PBA_CLR;
+
+ /* Auto-Mask Other interrupts upon ICR read */
+#define E1000_EIAC_MASK_82574 0x01F00000
+ ew32(IAM, ~E1000_EIAC_MASK_82574 | E1000_IMS_OTHER);
+ ctrl_ext |= E1000_CTRL_EXT_EIAME;
+ ew32(CTRL_EXT, ctrl_ext);
+ e1e_flush();
+}
+
+void e1000e_reset_interrupt_capability(struct e1000_adapter *adapter)
+{
+ if (adapter->msix_entries) {
+ pci_disable_msix(adapter->pdev);
+ kfree(adapter->msix_entries);
+ adapter->msix_entries = NULL;
+ } else if (adapter->flags & FLAG_MSI_ENABLED) {
+ pci_disable_msi(adapter->pdev);
+ adapter->flags &= ~FLAG_MSI_ENABLED;
+ }
+
+ return;
+}
+
+/**
+ * e1000e_set_interrupt_capability - set MSI or MSI-X if supported
+ *
+ * Attempt to configure interrupts using the best available
+ * capabilities of the hardware and kernel.
+ **/
+void e1000e_set_interrupt_capability(struct e1000_adapter *adapter)
+{
+ int err;
+ int numvecs, i;
+
+
+ switch (adapter->int_mode) {
+ case E1000E_INT_MODE_MSIX:
+ if (adapter->flags & FLAG_HAS_MSIX) {
+ numvecs = 3; /* RxQ0, TxQ0 and other */
+ adapter->msix_entries = kcalloc(numvecs,
+ sizeof(struct msix_entry),
+ GFP_KERNEL);
+ if (adapter->msix_entries) {
+ for (i = 0; i < numvecs; i++)
+ adapter->msix_entries[i].entry = i;
+
+ err = pci_enable_msix(adapter->pdev,
+ adapter->msix_entries,
+ numvecs);
+ if (err == 0)
+ return;
+ }
+ /* MSI-X failed, so fall through and try MSI */
+ e_err("Failed to initialize MSI-X interrupts. "
+ "Falling back to MSI interrupts.\n");
+ e1000e_reset_interrupt_capability(adapter);
+ }
+ adapter->int_mode = E1000E_INT_MODE_MSI;
+ /* Fall through */
+ case E1000E_INT_MODE_MSI:
+ if (!pci_enable_msi(adapter->pdev)) {
+ adapter->flags |= FLAG_MSI_ENABLED;
+ } else {
+ adapter->int_mode = E1000E_INT_MODE_LEGACY;
+ e_err("Failed to initialize MSI interrupts. Falling "
+ "back to legacy interrupts.\n");
+ }
+ /* Fall through */
+ case E1000E_INT_MODE_LEGACY:
+ /* Don't do anything; this is the system default */
+ break;
+ }
+
+ return;
+}
+
+/**
+ * e1000_request_msix - Initialize MSI-X interrupts
+ *
+ * e1000_request_msix allocates MSI-X vectors and requests interrupts from the
+ * kernel.
+ **/
+static int e1000_request_msix(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ int err = 0, vector = 0;
+
+ if (strlen(netdev->name) < (IFNAMSIZ - 5))
+ sprintf(adapter->rx_ring->name, "%s-rx0", netdev->name);
+ else
+ memcpy(adapter->rx_ring->name, netdev->name, IFNAMSIZ);
+ err = request_irq(adapter->msix_entries[vector].vector,
+ &e1000_intr_msix_rx, 0, adapter->rx_ring->name,
+ netdev);
+ if (err)
+ goto out;
+ adapter->rx_ring->itr_register = E1000_EITR_82574(vector);
+ adapter->rx_ring->itr_val = adapter->itr;
+ vector++;
+
+ if (strlen(netdev->name) < (IFNAMSIZ - 5))
+ sprintf(adapter->tx_ring->name, "%s-tx0", netdev->name);
+ else
+ memcpy(adapter->tx_ring->name, netdev->name, IFNAMSIZ);
+ err = request_irq(adapter->msix_entries[vector].vector,
+ &e1000_intr_msix_tx, 0, adapter->tx_ring->name,
+ netdev);
+ if (err)
+ goto out;
+ adapter->tx_ring->itr_register = E1000_EITR_82574(vector);
+ adapter->tx_ring->itr_val = adapter->itr;
+ vector++;
+
+ err = request_irq(adapter->msix_entries[vector].vector,
+ &e1000_msix_other, 0, netdev->name, netdev);
+ if (err)
+ goto out;
+
+ e1000_configure_msix(adapter);
+ return 0;
+out:
+ return err;
+}
+
+/**
+ * e1000_request_irq - initialize interrupts
+ *
+ * Attempts to configure interrupts using the best available
+ * capabilities of the hardware and kernel.
+ **/
+static int e1000_request_irq(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ int err;
+
+ if (adapter->msix_entries) {
+ err = e1000_request_msix(adapter);
+ if (!err)
+ return err;
+ /* fall back to MSI */
+ e1000e_reset_interrupt_capability(adapter);
+ adapter->int_mode = E1000E_INT_MODE_MSI;
+ e1000e_set_interrupt_capability(adapter);
+ }
+ if (adapter->flags & FLAG_MSI_ENABLED) {
+ err = request_irq(adapter->pdev->irq, &e1000_intr_msi, 0,
+ netdev->name, netdev);
+ if (!err)
+ return err;
+
+ /* fall back to legacy interrupt */
+ e1000e_reset_interrupt_capability(adapter);
+ adapter->int_mode = E1000E_INT_MODE_LEGACY;
+ }
+
+ err = request_irq(adapter->pdev->irq, &e1000_intr, IRQF_SHARED,
+ netdev->name, netdev);
+ if (err)
+ e_err("Unable to allocate interrupt, Error: %d\n", err);
+
+ return err;
+}
+
+
+static void e1000_free_irq(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+
+ if (adapter->msix_entries) {
+ int vector = 0;
+
+ free_irq(adapter->msix_entries[vector].vector, netdev);
+ vector++;
+
+ free_irq(adapter->msix_entries[vector].vector, netdev);
+ vector++;
+
+ /* Other Causes interrupt vector */
+ free_irq(adapter->msix_entries[vector].vector, netdev);
+ return;
+ }
+
+ free_irq(adapter->pdev->irq, netdev);
+}
+
+/**
+ * e1000_irq_disable - Mask off interrupt generation on the NIC
+ **/
+static void e1000_irq_disable(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ ew32(IMC, ~0);
+ if (adapter->msix_entries)
+ ew32(EIAC_82574, 0);
+ e1e_flush();
+ synchronize_irq(adapter->pdev->irq);
+}
+
+/**
+ * e1000_irq_enable - Enable default interrupt generation settings
+ **/
+static void e1000_irq_enable(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ if (adapter->msix_entries) {
+ ew32(EIAC_82574, adapter->eiac_mask & E1000_EIAC_MASK_82574);
+ ew32(IMS, adapter->eiac_mask | E1000_IMS_OTHER | E1000_IMS_LSC);
+ } else {
+ ew32(IMS, IMS_ENABLE_MASK);
+ }
+ e1e_flush();
+}
+
+/**
+ * e1000_get_hw_control - get control of the h/w from f/w
+ * @adapter: address of board private structure
+ *
+ * e1000_get_hw_control sets {CTRL_EXT|SWSM}:DRV_LOAD bit.
+ * For ASF and Pass Through versions of f/w this means that
+ * the driver is loaded. For AMT version (only with 82573)
+ * of the f/w this means that the network i/f is open.
+ **/
+static void e1000_get_hw_control(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl_ext;
+ u32 swsm;
+
+ /* Let firmware know the driver has taken over */
+ if (adapter->flags & FLAG_HAS_SWSM_ON_LOAD) {
+ swsm = er32(SWSM);
+ ew32(SWSM, swsm | E1000_SWSM_DRV_LOAD);
+ } else if (adapter->flags & FLAG_HAS_CTRLEXT_ON_LOAD) {
+ ctrl_ext = er32(CTRL_EXT);
+ ew32(CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_DRV_LOAD);
+ }
+}
+
+/**
+ * e1000_release_hw_control - release control of the h/w to f/w
+ * @adapter: address of board private structure
+ *
+ * e1000_release_hw_control resets {CTRL_EXT|SWSM}:DRV_LOAD bit.
+ * For ASF and Pass Through versions of f/w this means that the
+ * driver is no longer loaded. For AMT version (only with 82573) i
+ * of the f/w this means that the network i/f is closed.
+ *
+ **/
+static void e1000_release_hw_control(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl_ext;
+ u32 swsm;
+
+ /* Let firmware taken over control of h/w */
+ if (adapter->flags & FLAG_HAS_SWSM_ON_LOAD) {
+ swsm = er32(SWSM);
+ ew32(SWSM, swsm & ~E1000_SWSM_DRV_LOAD);
+ } else if (adapter->flags & FLAG_HAS_CTRLEXT_ON_LOAD) {
+ ctrl_ext = er32(CTRL_EXT);
+ ew32(CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_DRV_LOAD);
+ }
+}
+
+/**
+ * @e1000_alloc_ring - allocate memory for a ring structure
+ **/
+static int e1000_alloc_ring_dma(struct e1000_adapter *adapter,
+ struct e1000_ring *ring)
+{
+ struct pci_dev *pdev = adapter->pdev;
+
+ ring->desc = dma_alloc_coherent(&pdev->dev, ring->size, &ring->dma,
+ GFP_KERNEL);
+ if (!ring->desc)
+ return -ENOMEM;
+
+ return 0;
+}
+
+/**
+ * e1000e_setup_tx_resources - allocate Tx resources (Descriptors)
+ * @adapter: board private structure
+ *
+ * Return 0 on success, negative on failure
+ **/
+int e1000e_setup_tx_resources(struct e1000_adapter *adapter)
+{
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ int err = -ENOMEM, size;
+
+ size = sizeof(struct e1000_buffer) * tx_ring->count;
+ tx_ring->buffer_info = vmalloc(size);
+ if (!tx_ring->buffer_info)
+ goto err;
+ memset(tx_ring->buffer_info, 0, size);
+
+ /* round up to nearest 4K */
+ tx_ring->size = tx_ring->count * sizeof(struct e1000_tx_desc);
+ tx_ring->size = ALIGN(tx_ring->size, 4096);
+
+ err = e1000_alloc_ring_dma(adapter, tx_ring);
+ if (err)
+ goto err;
+
+ tx_ring->next_to_use = 0;
+ tx_ring->next_to_clean = 0;
+ spin_lock_init(&adapter->tx_queue_lock);
+
+ return 0;
+err:
+ vfree(tx_ring->buffer_info);
+ e_err("Unable to allocate memory for the transmit descriptor ring\n");
+ return err;
+}
+
+/**
+ * e1000e_setup_rx_resources - allocate Rx resources (Descriptors)
+ * @adapter: board private structure
+ *
+ * Returns 0 on success, negative on failure
+ **/
+int e1000e_setup_rx_resources(struct e1000_adapter *adapter)
+{
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ struct e1000_buffer *buffer_info;
+ int i, size, desc_len, err = -ENOMEM;
+
+ size = sizeof(struct e1000_buffer) * rx_ring->count;
+ rx_ring->buffer_info = vmalloc(size);
+ if (!rx_ring->buffer_info)
+ goto err;
+ memset(rx_ring->buffer_info, 0, size);
+
+ for (i = 0; i < rx_ring->count; i++) {
+ buffer_info = &rx_ring->buffer_info[i];
+ buffer_info->ps_pages = kcalloc(PS_PAGE_BUFFERS,
+ sizeof(struct e1000_ps_page),
+ GFP_KERNEL);
+ if (!buffer_info->ps_pages)
+ goto err_pages;
+ }
+
+ desc_len = sizeof(union e1000_rx_desc_packet_split);
+
+ /* Round up to nearest 4K */
+ rx_ring->size = rx_ring->count * desc_len;
+ rx_ring->size = ALIGN(rx_ring->size, 4096);
+
+ err = e1000_alloc_ring_dma(adapter, rx_ring);
+ if (err)
+ goto err_pages;
+
+ rx_ring->next_to_clean = 0;
+ rx_ring->next_to_use = 0;
+ rx_ring->rx_skb_top = NULL;
+
+ return 0;
+
+err_pages:
+ for (i = 0; i < rx_ring->count; i++) {
+ buffer_info = &rx_ring->buffer_info[i];
+ kfree(buffer_info->ps_pages);
+ }
+err:
+ vfree(rx_ring->buffer_info);
+ e_err("Unable to allocate memory for the transmit descriptor ring\n");
+ return err;
+}
+
+/**
+ * e1000_clean_tx_ring - Free Tx Buffers
+ * @adapter: board private structure
+ **/
+static void e1000_clean_tx_ring(struct e1000_adapter *adapter)
+{
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ struct e1000_buffer *buffer_info;
+ unsigned long size;
+ unsigned int i;
+
+ for (i = 0; i < tx_ring->count; i++) {
+ buffer_info = &tx_ring->buffer_info[i];
+ e1000_put_txbuf(adapter, buffer_info);
+ }
+
+ size = sizeof(struct e1000_buffer) * tx_ring->count;
+ memset(tx_ring->buffer_info, 0, size);
+
+ memset(tx_ring->desc, 0, tx_ring->size);
+
+ tx_ring->next_to_use = 0;
+ tx_ring->next_to_clean = 0;
+
+ writel(0, adapter->hw.hw_addr + tx_ring->head);
+ writel(0, adapter->hw.hw_addr + tx_ring->tail);
+}
+
+/**
+ * e1000e_free_tx_resources - Free Tx Resources per Queue
+ * @adapter: board private structure
+ *
+ * Free all transmit software resources
+ **/
+void e1000e_free_tx_resources(struct e1000_adapter *adapter)
+{
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+
+ e1000_clean_tx_ring(adapter);
+
+ vfree(tx_ring->buffer_info);
+ tx_ring->buffer_info = NULL;
+
+ dma_free_coherent(&pdev->dev, tx_ring->size, tx_ring->desc,
+ tx_ring->dma);
+ tx_ring->desc = NULL;
+}
+
+/**
+ * e1000e_free_rx_resources - Free Rx Resources
+ * @adapter: board private structure
+ *
+ * Free all receive software resources
+ **/
+
+void e1000e_free_rx_resources(struct e1000_adapter *adapter)
+{
+ struct pci_dev *pdev = adapter->pdev;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ int i;
+
+ e1000_clean_rx_ring(adapter);
+
+ for (i = 0; i < rx_ring->count; i++) {
+ kfree(rx_ring->buffer_info[i].ps_pages);
+ }
+
+ vfree(rx_ring->buffer_info);
+ rx_ring->buffer_info = NULL;
+
+ dma_free_coherent(&pdev->dev, rx_ring->size, rx_ring->desc,
+ rx_ring->dma);
+ rx_ring->desc = NULL;
+}
+
+/**
+ * e1000_update_itr - update the dynamic ITR value based on statistics
+ * @adapter: pointer to adapter
+ * @itr_setting: current adapter->itr
+ * @packets: the number of packets during this measurement interval
+ * @bytes: the number of bytes during this measurement interval
+ *
+ * Stores a new ITR value based on packets and byte
+ * counts during the last interrupt. The advantage of per interrupt
+ * computation is faster updates and more accurate ITR for the current
+ * traffic pattern. Constants in this function were computed
+ * based on theoretical maximum wire speed and thresholds were set based
+ * on testing data as well as attempting to minimize response time
+ * while increasing bulk throughput. This functionality is controlled
+ * by the InterruptThrottleRate module parameter.
+ **/
+static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
+ u16 itr_setting, int packets,
+ int bytes)
+{
+ unsigned int retval = itr_setting;
+
+ if (packets == 0)
+ goto update_itr_done;
+
+ switch (itr_setting) {
+ case lowest_latency:
+ /* handle TSO and jumbo frames */
+ if (bytes/packets > 8000)
+ retval = bulk_latency;
+ else if ((packets < 5) && (bytes > 512)) {
+ retval = low_latency;
+ }
+ break;
+ case low_latency: /* 50 usec aka 20000 ints/s */
+ if (bytes > 10000) {
+ /* this if handles the TSO accounting */
+ if (bytes/packets > 8000) {
+ retval = bulk_latency;
+ } else if ((packets < 10) || ((bytes/packets) > 1200)) {
+ retval = bulk_latency;
+ } else if ((packets > 35)) {
+ retval = lowest_latency;
+ }
+ } else if (bytes/packets > 2000) {
+ retval = bulk_latency;
+ } else if (packets <= 2 && bytes < 512) {
+ retval = lowest_latency;
+ }
+ break;
+ case bulk_latency: /* 250 usec aka 4000 ints/s */
+ if (bytes > 25000) {
+ if (packets > 35) {
+ retval = low_latency;
+ }
+ } else if (bytes < 6000) {
+ retval = low_latency;
+ }
+ break;
+ }
+
+update_itr_done:
+ return retval;
+}
+
+static void e1000_set_itr(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 current_itr;
+ u32 new_itr = adapter->itr;
+
+ /* for non-gigabit speeds, just fix the interrupt rate at 4000 */
+ if (adapter->link_speed != SPEED_1000) {
+ current_itr = 0;
+ new_itr = 4000;
+ goto set_itr_now;
+ }
+
+ adapter->tx_itr = e1000_update_itr(adapter,
+ adapter->tx_itr,
+ adapter->total_tx_packets,
+ adapter->total_tx_bytes);
+ /* conservative mode (itr 3) eliminates the lowest_latency setting */
+ if (adapter->itr_setting == 3 && adapter->tx_itr == lowest_latency)
+ adapter->tx_itr = low_latency;
+
+ adapter->rx_itr = e1000_update_itr(adapter,
+ adapter->rx_itr,
+ adapter->total_rx_packets,
+ adapter->total_rx_bytes);
+ /* conservative mode (itr 3) eliminates the lowest_latency setting */
+ if (adapter->itr_setting == 3 && adapter->rx_itr == lowest_latency)
+ adapter->rx_itr = low_latency;
+
+ current_itr = max(adapter->rx_itr, adapter->tx_itr);
+
+ switch (current_itr) {
+ /* counts and packets in update_itr are dependent on these numbers */
+ case lowest_latency:
+ new_itr = 70000;
+ break;
+ case low_latency:
+ new_itr = 20000; /* aka hwitr = ~200 */
+ break;
+ case bulk_latency:
+ new_itr = 4000;
+ break;
+ default:
+ break;
+ }
+
+set_itr_now:
+ if (new_itr != adapter->itr) {
+ /*
+ * this attempts to bias the interrupt rate towards Bulk
+ * by adding intermediate steps when interrupt rate is
+ * increasing
+ */
+ new_itr = new_itr > adapter->itr ?
+ min(adapter->itr + (new_itr >> 2), new_itr) :
+ new_itr;
+ adapter->itr = new_itr;
+ adapter->rx_ring->itr_val = new_itr;
+ if (adapter->msix_entries)
+ adapter->rx_ring->set_itr = 1;
+ else
+ ew32(ITR, 1000000000 / (new_itr * 256));
+ }
+}
+
+/**
+ * e1000_alloc_queues - Allocate memory for all rings
+ * @adapter: board private structure to initialize
+ **/
+static int __devinit e1000_alloc_queues(struct e1000_adapter *adapter)
+{
+ adapter->tx_ring = kzalloc(sizeof(struct e1000_ring), GFP_KERNEL);
+ if (!adapter->tx_ring)
+ goto err;
+
+ adapter->rx_ring = kzalloc(sizeof(struct e1000_ring), GFP_KERNEL);
+ if (!adapter->rx_ring)
+ goto err;
+
+ return 0;
+err:
+ e_err("Unable to allocate memory for queues\n");
+ kfree(adapter->rx_ring);
+ kfree(adapter->tx_ring);
+ return -ENOMEM;
+}
+
+/**
+ * e1000_clean - NAPI Rx polling callback
+ * @napi: struct associated with this polling callback
+ * @budget: amount of packets driver is allowed to process this poll
+ **/
+static int e1000_clean(struct net_device *poll_dev, int *budget)
+{
+ struct e1000_adapter *adapter = poll_dev->priv;
+ struct e1000_hw *hw = &adapter->hw;
+ int work_to_do = min(*budget, poll_dev->quota);
+ int tx_cleaned = 0, work_done = 0;
+
+ if (adapter->msix_entries &&
+ !(adapter->rx_ring->ims_val & adapter->tx_ring->ims_val))
+ goto clean_rx;
+
+ /* Keep link state information with original netdev */
+ if (!netif_carrier_ok(poll_dev))
+ goto quit_polling;
+
+ /*
+ * e1000_clean is called per-cpu. This lock protects
+ * tx_ring from being cleaned by multiple cpus
+ * simultaneously. A failure obtaining the lock means
+ * tx_ring is currently being cleaned anyway.
+ */
+ if (spin_trylock(&adapter->tx_queue_lock)) {
+ tx_cleaned = e1000_clean_tx_irq(adapter);
+ spin_unlock(&adapter->tx_queue_lock);
+ }
+
+clean_rx:
+ adapter->clean_rx(adapter, &work_done, work_to_do);
+ *budget -= work_done;
+ poll_dev->quota -= work_done;
+
+ /* If no Tx and not enough Rx work done, exit the polling mode */
+ if ((!tx_cleaned && (work_done == 0)) ||
+ !netif_running(poll_dev)) {
+quit_polling:
+ if (adapter->itr_setting & 3)
+ e1000_set_itr(adapter);
+ netif_rx_complete(poll_dev);
+ if (adapter->msix_entries)
+ ew32(IMS, adapter->rx_ring->ims_val);
+ else
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ e1000_irq_enable(adapter);
+ return 0;
+ }
+
+ return 1;
+}
+
+static void e1000_vlan_rx_add_vid(struct net_device *netdev, u16 vid)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 vfta, index;
+
+ /* don't update vlan cookie if already programmed */
+ if ((adapter->hw.mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN) &&
+ (vid == adapter->mng_vlan_id))
+ return;
+ /* add VID to filter table */
+ index = (vid >> 5) & 0x7F;
+ vfta = E1000_READ_REG_ARRAY(hw, E1000_VFTA, index);
+ vfta |= (1 << (vid & 0x1F));
+ e1000e_write_vfta(hw, index, vfta);
+}
+
+static void e1000_vlan_rx_kill_vid(struct net_device *netdev, u16 vid)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 vfta, index;
+
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ e1000_irq_disable(adapter);
+ vlan_group_set_device(adapter->vlgrp, vid, NULL);
+
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ e1000_irq_enable(adapter);
+
+ if ((adapter->hw.mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN) &&
+ (vid == adapter->mng_vlan_id)) {
+ /* release control to f/w */
+ e1000_release_hw_control(adapter);
+ return;
+ }
+
+ /* remove VID from filter table */
+ index = (vid >> 5) & 0x7F;
+ vfta = E1000_READ_REG_ARRAY(hw, E1000_VFTA, index);
+ vfta &= ~(1 << (vid & 0x1F));
+ e1000e_write_vfta(hw, index, vfta);
+}
+
+static void e1000_update_mng_vlan(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ u16 vid = adapter->hw.mng_cookie.vlan_id;
+ u16 old_vid = adapter->mng_vlan_id;
+
+ if (!adapter->vlgrp)
+ return;
+
+ if (!vlan_group_get_device(adapter->vlgrp, vid)) {
+ adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
+ if (adapter->hw.mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN) {
+ e1000_vlan_rx_add_vid(netdev, vid);
+ adapter->mng_vlan_id = vid;
+ }
+
+ if ((old_vid != (u16)E1000_MNG_VLAN_NONE) &&
+ (vid != old_vid) &&
+ !vlan_group_get_device(adapter->vlgrp, old_vid))
+ e1000_vlan_rx_kill_vid(netdev, old_vid);
+ } else {
+ adapter->mng_vlan_id = vid;
+ }
+}
+
+
+static void e1000_vlan_rx_register(struct net_device *netdev,
+ struct vlan_group *grp)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl, rctl;
+
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ e1000_irq_disable(adapter);
+ adapter->vlgrp = grp;
+
+ if (grp) {
+ /* enable VLAN tag insert/strip */
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_VME;
+ ew32(CTRL, ctrl);
+
+ if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) {
+ /* enable VLAN receive filtering */
+ rctl = er32(RCTL);
+ rctl &= ~E1000_RCTL_CFIEN;
+ ew32(RCTL, rctl);
+ e1000_update_mng_vlan(adapter);
+ }
+ } else {
+ /* disable VLAN tag insert/strip */
+ ctrl = er32(CTRL);
+ ctrl &= ~E1000_CTRL_VME;
+ ew32(CTRL, ctrl);
+
+ if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) {
+ if (adapter->mng_vlan_id !=
+ (u16)E1000_MNG_VLAN_NONE) {
+ e1000_vlan_rx_kill_vid(netdev,
+ adapter->mng_vlan_id);
+ adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
+ }
+ }
+ }
+
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ e1000_irq_enable(adapter);
+}
+
+static void e1000_restore_vlan(struct e1000_adapter *adapter)
+{
+ u16 vid;
+
+ e1000_vlan_rx_register(adapter->netdev, adapter->vlgrp);
+
+ if (!adapter->vlgrp)
+ return;
+
+ for (vid = 0; vid < VLAN_GROUP_ARRAY_LEN; vid++) {
+ if (!vlan_group_get_device(adapter->vlgrp, vid))
+ continue;
+ e1000_vlan_rx_add_vid(adapter->netdev, vid);
+ }
+}
+
+static void e1000_init_manageability(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 manc, manc2h;
+
+ if (!(adapter->flags & FLAG_MNG_PT_ENABLED))
+ return;
+
+ manc = er32(MANC);
+
+ /*
+ * enable receiving management packets to the host. this will probably
+ * generate destination unreachable messages from the host OS, but
+ * the packets will be handled on SMBUS
+ */
+ manc |= E1000_MANC_EN_MNG2HOST;
+ manc2h = er32(MANC2H);
+#define E1000_MNG2HOST_PORT_623 (1 << 5)
+#define E1000_MNG2HOST_PORT_664 (1 << 6)
+ manc2h |= E1000_MNG2HOST_PORT_623;
+ manc2h |= E1000_MNG2HOST_PORT_664;
+ ew32(MANC2H, manc2h);
+ ew32(MANC, manc);
+}
+
+/**
+ * e1000_configure_tx - Configure 8254x Transmit Unit after Reset
+ * @adapter: board private structure
+ *
+ * Configure the Tx unit of the MAC after a reset.
+ **/
+static void e1000_configure_tx(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ u64 tdba;
+ u32 tdlen, tctl, tipg, tarc;
+ u32 ipgr1, ipgr2;
+
+ /* Setup the HW Tx Head and Tail descriptor pointers */
+ tdba = tx_ring->dma;
+ tdlen = tx_ring->count * sizeof(struct e1000_tx_desc);
+ ew32(TDBAL, (tdba & DMA_32BIT_MASK));
+ ew32(TDBAH, (tdba >> 32));
+ ew32(TDLEN, tdlen);
+ ew32(TDH, 0);
+ ew32(TDT, 0);
+ tx_ring->head = E1000_TDH;
+ tx_ring->tail = E1000_TDT;
+
+ /* Set the default values for the Tx Inter Packet Gap timer */
+ tipg = DEFAULT_82543_TIPG_IPGT_COPPER; /* 8 */
+ ipgr1 = DEFAULT_82543_TIPG_IPGR1; /* 8 */
+ ipgr2 = DEFAULT_82543_TIPG_IPGR2; /* 6 */
+
+ if (adapter->flags & FLAG_TIPG_MEDIUM_FOR_80003ESLAN)
+ ipgr2 = DEFAULT_80003ES2LAN_TIPG_IPGR2; /* 7 */
+
+ tipg |= ipgr1 << E1000_TIPG_IPGR1_SHIFT;
+ tipg |= ipgr2 << E1000_TIPG_IPGR2_SHIFT;
+ ew32(TIPG, tipg);
+
+ /* Set the Tx Interrupt Delay register */
+ ew32(TIDV, adapter->tx_int_delay);
+ /* Tx irq moderation */
+ ew32(TADV, adapter->tx_abs_int_delay);
+
+ /* Program the Transmit Control Register */
+ tctl = er32(TCTL);
+ tctl &= ~E1000_TCTL_CT;
+ tctl |= E1000_TCTL_PSP | E1000_TCTL_RTLC |
+ (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT);
+
+ if (adapter->flags & FLAG_TARC_SPEED_MODE_BIT) {
+ tarc = er32(TARC(0));
+ /*
+ * set the speed mode bit, we'll clear it if we're not at
+ * gigabit link later
+ */
+#define SPEED_MODE_BIT (1 << 21)
+ tarc |= SPEED_MODE_BIT;
+ ew32(TARC(0), tarc);
+ }
+
+ /* errata: program both queues to unweighted RR */
+ if (adapter->flags & FLAG_TARC_SET_BIT_ZERO) {
+ tarc = er32(TARC(0));
+ tarc |= 1;
+ ew32(TARC(0), tarc);
+ tarc = er32(TARC(1));
+ tarc |= 1;
+ ew32(TARC(1), tarc);
+ }
+
+ e1000e_config_collision_dist(hw);
+
+ /* Setup Transmit Descriptor Settings for eop descriptor */
+ adapter->txd_cmd = E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS;
+
+ /* only set IDE if we are delaying interrupts using the timers */
+ if (adapter->tx_int_delay)
+ adapter->txd_cmd |= E1000_TXD_CMD_IDE;
+
+ /* enable Report Status bit */
+ adapter->txd_cmd |= E1000_TXD_CMD_RS;
+
+ ew32(TCTL, tctl);
+
+ adapter->tx_queue_len = adapter->netdev->tx_queue_len;
+}
+
+/**
+ * e1000_setup_rctl - configure the receive control registers
+ * @adapter: Board private structure
+ **/
+#define PAGE_USE_COUNT(S) (((S) >> PAGE_SHIFT) + \
+ (((S) & (PAGE_SIZE - 1)) ? 1 : 0))
+static void e1000_setup_rctl(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 rctl, rfctl;
+ u32 psrctl = 0;
+ u32 pages = 0;
+
+ /* Program MC offset vector base */
+ rctl = er32(RCTL);
+ rctl &= ~(3 << E1000_RCTL_MO_SHIFT);
+ rctl |= E1000_RCTL_EN | E1000_RCTL_BAM |
+ E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF |
+ (adapter->hw.mac.mc_filter_type << E1000_RCTL_MO_SHIFT);
+
+ /* Do not Store bad packets */
+ rctl &= ~E1000_RCTL_SBP;
+
+ /* Enable Long Packet receive */
+ if (adapter->netdev->mtu <= ETH_DATA_LEN)
+ rctl &= ~E1000_RCTL_LPE;
+ else
+ rctl |= E1000_RCTL_LPE;
+
+ /* Enable hardware CRC frame stripping */
+ rctl |= E1000_RCTL_SECRC;
+
+ /* Setup buffer sizes */
+ rctl &= ~E1000_RCTL_SZ_4096;
+ rctl |= E1000_RCTL_BSEX;
+ switch (adapter->rx_buffer_len) {
+ case 256:
+ rctl |= E1000_RCTL_SZ_256;
+ rctl &= ~E1000_RCTL_BSEX;
+ break;
+ case 512:
+ rctl |= E1000_RCTL_SZ_512;
+ rctl &= ~E1000_RCTL_BSEX;
+ break;
+ case 1024:
+ rctl |= E1000_RCTL_SZ_1024;
+ rctl &= ~E1000_RCTL_BSEX;
+ break;
+ case 2048:
+ default:
+ rctl |= E1000_RCTL_SZ_2048;
+ rctl &= ~E1000_RCTL_BSEX;
+ break;
+ case 4096:
+ rctl |= E1000_RCTL_SZ_4096;
+ break;
+ case 8192:
+ rctl |= E1000_RCTL_SZ_8192;
+ break;
+ case 16384:
+ rctl |= E1000_RCTL_SZ_16384;
+ break;
+ }
+
+ /*
+ * 82571 and greater support packet-split where the protocol
+ * header is placed in skb->data and the packet data is
+ * placed in pages hanging off of skb_shinfo(skb)->nr_frags.
+ * In the case of a non-split, skb->data is linearly filled,
+ * followed by the page buffers. Therefore, skb->data is
+ * sized to hold the largest protocol header.
+ *
+ * allocations using alloc_page take too long for regular MTU
+ * so only enable packet split for jumbo frames
+ *
+ * Using pages when the page size is greater than 16k wastes
+ * a lot of memory, since we allocate 3 pages at all times
+ * per packet.
+ */
+ pages = PAGE_USE_COUNT(adapter->netdev->mtu);
+ if (!(adapter->flags & FLAG_IS_ICH) && (pages <= 3) &&
+ (PAGE_SIZE <= 16384) && (rctl & E1000_RCTL_LPE))
+ adapter->rx_ps_pages = pages;
+ else
+ adapter->rx_ps_pages = 0;
+
+ if (adapter->rx_ps_pages) {
+ /* Configure extra packet-split registers */
+ rfctl = er32(RFCTL);
+ rfctl |= E1000_RFCTL_EXTEN;
+ /*
+ * disable packet split support for IPv6 extension headers,
+ * because some malformed IPv6 headers can hang the Rx
+ */
+ rfctl |= (E1000_RFCTL_IPV6_EX_DIS |
+ E1000_RFCTL_NEW_IPV6_EXT_DIS);
+
+ ew32(RFCTL, rfctl);
+
+ /* Enable Packet split descriptors */
+ rctl |= E1000_RCTL_DTYP_PS;
+
+ /* Enable hardware CRC frame stripping */
+ rctl |= E1000_RCTL_SECRC;
+
+ psrctl |= adapter->rx_ps_bsize0 >>
+ E1000_PSRCTL_BSIZE0_SHIFT;
+
+ switch (adapter->rx_ps_pages) {
+ case 3:
+ psrctl |= PAGE_SIZE <<
+ E1000_PSRCTL_BSIZE3_SHIFT;
+ case 2:
+ psrctl |= PAGE_SIZE <<
+ E1000_PSRCTL_BSIZE2_SHIFT;
+ case 1:
+ psrctl |= PAGE_SIZE >>
+ E1000_PSRCTL_BSIZE1_SHIFT;
+ break;
+ }
+
+ ew32(PSRCTL, psrctl);
+ }
+
+ ew32(RCTL, rctl);
+ /* just started the receive unit, no need to restart */
+ adapter->flags &= ~FLAG_RX_RESTART_NOW;
+}
+
+/**
+ * e1000_configure_rx - Configure Receive Unit after Reset
+ * @adapter: board private structure
+ *
+ * Configure the Rx unit of the MAC after a reset.
+ **/
+static void e1000_configure_rx(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_ring *rx_ring = adapter->rx_ring;
+ u64 rdba;
+ u32 rdlen, rctl, rxcsum, ctrl_ext;
+
+ if (adapter->rx_ps_pages) {
+ /* this is a 32 byte descriptor */
+ rdlen = rx_ring->count *
+ sizeof(union e1000_rx_desc_packet_split);
+ adapter->clean_rx = e1000_clean_rx_irq_ps;
+ adapter->alloc_rx_buf = e1000_alloc_rx_buffers_ps;
+ } else if (adapter->netdev->mtu > ETH_FRAME_LEN + ETH_FCS_LEN) {
+ rdlen = rx_ring->count * sizeof(struct e1000_rx_desc);
+ adapter->clean_rx = e1000_clean_jumbo_rx_irq;
+ adapter->alloc_rx_buf = e1000_alloc_jumbo_rx_buffers;
+ } else {
+ rdlen = rx_ring->count * sizeof(struct e1000_rx_desc);
+ adapter->clean_rx = e1000_clean_rx_irq;
+ adapter->alloc_rx_buf = e1000_alloc_rx_buffers;
+ }
+
+ /* disable receives while setting up the descriptors */
+ rctl = er32(RCTL);
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
+ e1e_flush();
+ msleep(10);
+
+ /* set the Receive Delay Timer Register */
+ ew32(RDTR, adapter->rx_int_delay);
+
+ /* irq moderation */
+ ew32(RADV, adapter->rx_abs_int_delay);
+ if (adapter->itr_setting != 0)
+ ew32(ITR, 1000000000 / (adapter->itr * 256));
+
+ ctrl_ext = er32(CTRL_EXT);
+ /* Reset delay timers after every interrupt */
+ ctrl_ext |= E1000_CTRL_EXT_INT_TIMER_CLR;
+ /* Auto-Mask interrupts upon ICR access */
+ ctrl_ext |= E1000_CTRL_EXT_IAME;
+ ew32(IAM, 0xffffffff);
+ ew32(CTRL_EXT, ctrl_ext);
+ e1e_flush();
+
+ /*
+ * Setup the HW Rx Head and Tail Descriptor Pointers and
+ * the Base and Length of the Rx Descriptor Ring
+ */
+ rdba = rx_ring->dma;
+ ew32(RDBAL, (rdba & DMA_32BIT_MASK));
+ ew32(RDBAH, (rdba >> 32));
+ ew32(RDLEN, rdlen);
+ ew32(RDH, 0);
+ ew32(RDT, 0);
+ rx_ring->head = E1000_RDH;
+ rx_ring->tail = E1000_RDT;
+
+ /* Enable Receive Checksum Offload for TCP and UDP */
+ rxcsum = er32(RXCSUM);
+ if (adapter->flags & FLAG_RX_CSUM_ENABLED) {
+ rxcsum |= E1000_RXCSUM_TUOFL;
+
+ /*
+ * IPv4 payload checksum for UDP fragments must be
+ * used in conjunction with packet-split.
+ */
+ if (adapter->rx_ps_pages)
+ rxcsum |= E1000_RXCSUM_IPPCSE;
+ } else {
+ rxcsum &= ~E1000_RXCSUM_TUOFL;
+ /* no need to clear IPPCSE as it defaults to 0 */
+ }
+ ew32(RXCSUM, rxcsum);
+
+ /*
+ * Enable early receives on supported devices, only takes effect when
+ * packet size is equal or larger than the specified value (in 8 byte
+ * units), e.g. using jumbo frames when setting to E1000_ERT_2048
+ */
+ if ((adapter->flags & FLAG_HAS_ERT) &&
+ (adapter->netdev->mtu > ETH_DATA_LEN)) {
+ u32 rxdctl = er32(RXDCTL(0));
+ ew32(RXDCTL(0), rxdctl | 0x3);
+ ew32(ERT, E1000_ERT_2048 | (1 << 13));
+ /*
+ * With jumbo frames and early-receive enabled, excessive
+ * C4->C2 latencies result in dropped transactions.
+ */
+#if 0 /* not in RHEL */
+ pm_qos_update_requirement(PM_QOS_CPU_DMA_LATENCY,
+ e1000e_driver_name, 55);
+ } else {
+ pm_qos_update_requirement(PM_QOS_CPU_DMA_LATENCY,
+ e1000e_driver_name,
+ PM_QOS_DEFAULT_VALUE);
+ }
+#else
+ }
+#endif
+
+ /* Enable Receives */
+ ew32(RCTL, rctl);
+}
+
+/**
+ * e1000_update_mc_addr_list - Update Multicast addresses
+ * @hw: pointer to the HW structure
+ * @mc_addr_list: array of multicast addresses to program
+ * @mc_addr_count: number of multicast addresses to program
+ * @rar_used_count: the first RAR register free to program
+ * @rar_count: total number of supported Receive Address Registers
+ *
+ * Updates the Receive Address Registers and Multicast Table Array.
+ * The caller must have a packed mc_addr_list of multicast addresses.
+ * The parameter rar_count will usually be hw->mac.rar_entry_count
+ * unless there are workarounds that change this. Currently no func pointer
+ * exists and all implementations are handled in the generic version of this
+ * function.
+ **/
+static void e1000_update_mc_addr_list(struct e1000_hw *hw, u8 *mc_addr_list,
+ u32 mc_addr_count, u32 rar_used_count,
+ u32 rar_count)
+{
+ hw->mac.ops.update_mc_addr_list(hw, mc_addr_list, mc_addr_count,
+ rar_used_count, rar_count);
+}
+
+/**
+ * e1000_set_multi - Multicast and Promiscuous mode set
+ * @netdev: network interface device structure
+ *
+ * The set_multi entry point is called whenever the multicast address
+ * list or the network interface flags are updated. This routine is
+ * responsible for configuring the hardware for proper multicast,
+ * promiscuous mode, and all-multi behavior.
+ **/
+static void e1000_set_multi(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_mac_info *mac = &hw->mac;
+ struct dev_mc_list *mc_ptr;
+ u8 *mta_list;
+ u32 rctl;
+ int i;
+
+ /* Check for Promiscuous and All Multicast modes */
+
+ rctl = er32(RCTL);
+
+ if (netdev->flags & IFF_PROMISC) {
+ rctl |= (E1000_RCTL_UPE | E1000_RCTL_MPE);
+ rctl &= ~E1000_RCTL_VFE;
+ } else {
+ if (netdev->flags & IFF_ALLMULTI) {
+ rctl |= E1000_RCTL_MPE;
+ rctl &= ~E1000_RCTL_UPE;
+ } else {
+ rctl &= ~(E1000_RCTL_UPE | E1000_RCTL_MPE);
+ }
+ if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER)
+ rctl |= E1000_RCTL_VFE;
+ }
+
+ ew32(RCTL, rctl);
+
+ if (netdev->mc_count) {
+ mta_list = kmalloc(netdev->mc_count * 6, GFP_ATOMIC);
+ if (!mta_list)
+ return;
+
+ /* prepare a packed array of only addresses. */
+ mc_ptr = netdev->mc_list;
+
+ for (i = 0; i < netdev->mc_count; i++) {
+ if (!mc_ptr)
+ break;
+ memcpy(mta_list + (i*ETH_ALEN), mc_ptr->dmi_addr,
+ ETH_ALEN);
+ mc_ptr = mc_ptr->next;
+ }
+
+ e1000_update_mc_addr_list(hw, mta_list, i, 1,
+ mac->rar_entry_count);
+ kfree(mta_list);
+ } else {
+ /*
+ * if we're called from probe, we might not have
+ * anything to do here, so clear out the list
+ */
+ e1000_update_mc_addr_list(hw, NULL, 0, 1, mac->rar_entry_count);
+ }
+}
+
+/**
+ * e1000_configure - configure the hardware for Rx and Tx
+ * @adapter: private board structure
+ **/
+static void e1000_configure(struct e1000_adapter *adapter)
+{
+ e1000_set_multi(adapter->netdev);
+
+ e1000_restore_vlan(adapter);
+ e1000_init_manageability(adapter);
+
+ e1000_configure_tx(adapter);
+ e1000_setup_rctl(adapter);
+ e1000_configure_rx(adapter);
+ adapter->alloc_rx_buf(adapter, e1000_desc_unused(adapter->rx_ring));
+}
+
+/**
+ * e1000e_power_up_phy - restore link in case the phy was powered down
+ * @adapter: address of board private structure
+ *
+ * The phy may be powered down to save power and turn off link when the
+ * driver is unloaded and wake on lan is not enabled (among others)
+ * *** this routine MUST be followed by a call to e1000e_reset ***
+ **/
+void e1000e_power_up_phy(struct e1000_adapter *adapter)
+{
+ u16 mii_reg = 0;
+
+ /* Just clear the power down bit to wake the phy back up */
+ if (adapter->hw.phy.media_type == e1000_media_type_copper) {
+ /*
+ * According to the manual, the phy will retain its
+ * settings across a power-down/up cycle
+ */
+ e1e_rphy(&adapter->hw, PHY_CONTROL, &mii_reg);
+ mii_reg &= ~MII_CR_POWER_DOWN;
+ e1e_wphy(&adapter->hw, PHY_CONTROL, mii_reg);
+ }
+
+ adapter->hw.mac.ops.setup_link(&adapter->hw);
+}
+
+/**
+ * e1000_power_down_phy - Power down the PHY
+ *
+ * Power down the PHY so no link is implied when interface is down
+ * The PHY cannot be powered down is management or WoL is active
+ */
+static void e1000_power_down_phy(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 mii_reg;
+
+ /* WoL is enabled */
+ if (adapter->wol)
+ return;
+
+ /* non-copper PHY? */
+ if (adapter->hw.phy.media_type != e1000_media_type_copper)
+ return;
+
+ /* reset is blocked because of a SoL/IDER session */
+ if (e1000e_check_mng_mode(hw) || e1000_check_reset_block(hw))
+ return;
+
+ /* manageability (AMT) is enabled */
+ if (er32(MANC) & E1000_MANC_SMBUS_EN)
+ return;
+
+ /* power down the PHY */
+ e1e_rphy(hw, PHY_CONTROL, &mii_reg);
+ mii_reg |= MII_CR_POWER_DOWN;
+ e1e_wphy(hw, PHY_CONTROL, mii_reg);
+ mdelay(1);
+}
+
+/**
+ * e1000e_reset - bring the hardware into a known good state
+ *
+ * This function boots the hardware and enables some settings that
+ * require a configuration cycle of the hardware - those cannot be
+ * set/changed during runtime. After reset the device needs to be
+ * properly configured for Rx, Tx etc.
+ */
+void e1000e_reset(struct e1000_adapter *adapter)
+{
+ struct e1000_mac_info *mac = &adapter->hw.mac;
+ struct e1000_fc_info *fc = &adapter->hw.fc;
+ struct e1000_hw *hw = &adapter->hw;
+ u32 tx_space, min_tx_space, min_rx_space;
+ u32 pba = adapter->pba;
+ u16 hwm;
+
+ /* reset Packet Buffer Allocation to default */
+ ew32(PBA, pba);
+
+ if (adapter->max_frame_size > ETH_FRAME_LEN + ETH_FCS_LEN) {
+ /*
+ * To maintain wire speed transmits, the Tx FIFO should be
+ * large enough to accommodate two full transmit packets,
+ * rounded up to the next 1KB and expressed in KB. Likewise,
+ * the Rx FIFO should be large enough to accommodate at least
+ * one full receive packet and is similarly rounded up and
+ * expressed in KB.
+ */
+ pba = er32(PBA);
+ /* upper 16 bits has Tx packet buffer allocation size in KB */
+ tx_space = pba >> 16;
+ /* lower 16 bits has Rx packet buffer allocation size in KB */
+ pba &= 0xffff;
+ /*
+ * the Tx fifo also stores 16 bytes of information about the tx
+ * but don't include ethernet FCS because hardware appends it
+ */
+ min_tx_space = (adapter->max_frame_size +
+ sizeof(struct e1000_tx_desc) -
+ ETH_FCS_LEN) * 2;
+ min_tx_space = ALIGN(min_tx_space, 1024);
+ min_tx_space >>= 10;
+ /* software strips receive CRC, so leave room for it */
+ min_rx_space = adapter->max_frame_size;
+ min_rx_space = ALIGN(min_rx_space, 1024);
+ min_rx_space >>= 10;
+
+ /*
+ * If current Tx allocation is less than the min Tx FIFO size,
+ * and the min Tx FIFO size is less than the current Rx FIFO
+ * allocation, take space away from current Rx allocation
+ */
+ if ((tx_space < min_tx_space) &&
+ ((min_tx_space - tx_space) < pba)) {
+ pba -= min_tx_space - tx_space;
+
+ /*
+ * if short on Rx space, Rx wins and must trump tx
+ * adjustment or use Early Receive if available
+ */
+ if ((pba < min_rx_space) &&
+ (!(adapter->flags & FLAG_HAS_ERT)))
+ /* ERT enabled in e1000_configure_rx */
+ pba = min_rx_space;
+ }
+
+ ew32(PBA, pba);
+ }
+
+
+ /*
+ * flow control settings
+ *
+ * The high water mark must be low enough to fit one full frame
+ * (or the size used for early receive) above it in the Rx FIFO.
+ * Set it to the lower of:
+ * - 90% of the Rx FIFO size, and
+ * - the full Rx FIFO size minus the early receive size (for parts
+ * with ERT support assuming ERT set to E1000_ERT_2048), or
+ * - the full Rx FIFO size minus one full frame
+ */
+ if (adapter->flags & FLAG_HAS_ERT)
+ hwm = min(((pba << 10) * 9 / 10),
+ ((pba << 10) - (E1000_ERT_2048 << 3)));
+ else
+ hwm = min(((pba << 10) * 9 / 10),
+ ((pba << 10) - adapter->max_frame_size));
+
+ fc->high_water = hwm & 0xFFF8; /* 8-byte granularity */
+ fc->low_water = fc->high_water - 8;
+
+ if (adapter->flags & FLAG_DISABLE_FC_PAUSE_TIME)
+ fc->pause_time = 0xFFFF;
+ else
+ fc->pause_time = E1000_FC_PAUSE_TIME;
+ fc->send_xon = 1;
+ fc->type = fc->original_type;
+
+ /* Allow time for pending master requests to run */
+ mac->ops.reset_hw(hw);
+
+ /*
+ * For parts with AMT enabled, let the firmware know
+ * that the network interface is in control
+ */
+ if (adapter->flags & FLAG_HAS_AMT)
+ e1000_get_hw_control(adapter);
+
+ ew32(WUC, 0);
+
+ if (mac->ops.init_hw(hw))
+ e_err("Hardware Error\n");
+
+ e1000_update_mng_vlan(adapter);
+
+ /* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */
+ ew32(VET, ETH_P_8021Q);
+
+ e1000e_reset_adaptive(hw);
+ e1000_get_phy_info(hw);
+
+ if (!(adapter->flags & FLAG_SMART_POWER_DOWN)) {
+ u16 phy_data = 0;
+ /*
+ * speed up time to link by disabling smart power down, ignore
+ * the return value of this function because there is nothing
+ * different we would do if it failed
+ */
+ e1e_rphy(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
+ phy_data &= ~IGP02E1000_PM_SPD;
+ e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
+ }
+}
+
+int e1000e_up(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+
+ /* hardware has been reset, we need to reload some things */
+ e1000_configure(adapter);
+
+ clear_bit(__E1000_DOWN, &adapter->state);
+
+ netif_poll_enable(adapter->netdev);
+ if (adapter->msix_entries)
+ e1000_configure_msix(adapter);
+ e1000_irq_enable(adapter);
+
+ /* fire a link change interrupt to start the watchdog */
+ ew32(ICS, E1000_ICS_LSC);
+ return 0;
+}
+
+void e1000e_down(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct e1000_hw *hw = &adapter->hw;
+ u32 tctl, rctl;
+
+ /*
+ * signal that we're down so the interrupt handler does not
+ * reschedule our watchdog timer
+ */
+ set_bit(__E1000_DOWN, &adapter->state);
+
+ /* disable receives in the hardware */
+ rctl = er32(RCTL);
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
+ /* flush and sleep below */
+
+ netif_stop_queue(netdev);
+
+ /* disable transmits in the hardware */
+ tctl = er32(TCTL);
+ tctl &= ~E1000_TCTL_EN;
+ ew32(TCTL, tctl);
+ /* flush both disables and wait for them to finish */
+ e1e_flush();
+ msleep(10);
+
+ netif_poll_disable(netdev);
+
+ e1000_irq_disable(adapter);
+
+ del_timer_sync(&adapter->watchdog_timer);
+ del_timer_sync(&adapter->phy_info_timer);
+
+ netdev->tx_queue_len = adapter->tx_queue_len;
+ netif_carrier_off(netdev);
+ adapter->link_speed = 0;
+ adapter->link_duplex = 0;
+
+ if (!pci_channel_offline(adapter->pdev))
+ e1000e_reset(adapter);
+ e1000_clean_tx_ring(adapter);
+ e1000_clean_rx_ring(adapter);
+
+ /*
+ * TODO: for power management, we could drop the link and
+ * pci_disable_device here.
+ */
+}
+
+void e1000e_reinit_locked(struct e1000_adapter *adapter)
+{
+ might_sleep();
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
+ msleep(1);
+ e1000e_down(adapter);
+ e1000e_up(adapter);
+ clear_bit(__E1000_RESETTING, &adapter->state);
+}
+
+/**
+ * e1000_sw_init - Initialize general software structures (struct e1000_adapter)
+ * @adapter: board private structure to initialize
+ *
+ * e1000_sw_init initializes the Adapter private data structure.
+ * Fields are initialized based on PCI device information and
+ * OS network device settings (MTU size).
+ **/
+static int __devinit e1000_sw_init(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+
+ adapter->rx_buffer_len = ETH_FRAME_LEN + VLAN_HLEN + ETH_FCS_LEN;
+ adapter->rx_ps_bsize0 = 128;
+ adapter->max_frame_size = netdev->mtu + ETH_HLEN + ETH_FCS_LEN;
+ adapter->min_frame_size = ETH_ZLEN + ETH_FCS_LEN;
+
+ e1000e_set_interrupt_capability(adapter);
+
+ if (e1000_alloc_queues(adapter))
+ return -ENOMEM;
+
+ spin_lock_init(&adapter->tx_queue_lock);
+
+ /* Explicitly disable IRQ since the NIC can be in any state. */
+ e1000_irq_disable(adapter);
+
+ spin_lock_init(&adapter->stats_lock);
+
+ set_bit(__E1000_DOWN, &adapter->state);
+ return 0;
+}
+
+/**
+ * e1000_intr_msi_test - Interrupt Handler
+ * @irq: interrupt number
+ * @data: pointer to a network interface device structure
+ **/
+static irqreturn_t e1000_intr_msi_test(int irq, void *data, struct pt_regs *regs)
+{
+ struct net_device *netdev = data;
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ u32 icr = er32(ICR);
+ e_dbg(netdev, "icr is %08X\n", icr);
+ if (icr & E1000_ICR_RXSEQ) {
+ adapter->flags &= ~FLAG_MSI_TEST_FAILED;
+ wmb();
+ }
+
+ return IRQ_HANDLED;
+}
+
+/**
+ * e1000_test_msi_interrupt - Returns 0 for successful test
+ * @adapter: board private struct
+ *
+ * code flow taken from tg3.c
+ **/
+static int e1000_test_msi_interrupt(struct e1000_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct e1000_hw *hw = &adapter->hw;
+ int err;
+
+ /* poll_enable hasn't been called yet, so don't need disable */
+ /* clear any pending events */
+ er32(ICR);
+
+ /* free the real vector and request a test handler */
+ e1000_free_irq(adapter);
+ e1000e_reset_interrupt_capability(adapter);
+
+ err = pci_enable_msi(adapter->pdev);
+ if (err)
+ goto msi_test_failed;
+
+ err = request_irq(adapter->pdev->irq, &e1000_intr_msi_test, 0,
+ netdev->name, netdev);
+ if (err) {
+ pci_disable_msi(adapter->pdev);
+ goto msi_test_failed;
+ }
+
+ /* Assume that the test fails, if it succeeds then the test
+ * MSI irq handler will unset this flag */
+ adapter->flags |= FLAG_MSI_TEST_FAILED;
+ wmb();
+
+ e1000_irq_enable(adapter);
+
+ /* fire an unusual interrupt on the test handler */
+ ew32(ICS, E1000_ICS_RXSEQ);
+ e1e_flush();
+ msleep(50);
+
+ e1000_irq_disable(adapter);
+
+ rmb();
+
+ if (adapter->flags & FLAG_MSI_TEST_FAILED) {
+ adapter->int_mode = E1000E_INT_MODE_LEGACY;
+ err = -EIO;
+ e_dbg(netdev, "MSI interrupt test failed!\n");
+ }
+
+ free_irq(adapter->pdev->irq, netdev);
+ pci_disable_msi(adapter->pdev);
+
+ if (err == -EIO)
+ goto msi_test_failed;
+
+ /* okay so the test worked, restore settings */
+ e_dbg(netdev, "MSI interrupt test succeeded!\n");
+msi_test_failed:
+ e1000e_set_interrupt_capability(adapter);
+ e1000_request_irq(adapter);
+ return err;
+}
+
+/**
+ * e1000_test_msi - Returns 0 if MSI test succeeds or INTx mode is restored
+ * @adapter: board private struct
+ *
+ * code flow taken from tg3.c, called with e1000 interrupts disabled.
+ **/
+static int e1000_test_msi(struct e1000_adapter *adapter)
+{
+ int err;
+ u16 pci_cmd;
+
+ if (!(adapter->flags & FLAG_MSI_ENABLED))
+ return 0;
+
+ /* disable SERR in case the MSI write causes a master abort */
+ pci_read_config_word(adapter->pdev, PCI_COMMAND, &pci_cmd);
+ pci_write_config_word(adapter->pdev, PCI_COMMAND,
+ pci_cmd & ~PCI_COMMAND_SERR);
+
+ err = e1000_test_msi_interrupt(adapter);
+
+ /* restore previous setting of command word */
+ pci_write_config_word(adapter->pdev, PCI_COMMAND, pci_cmd);
+
+ /* success ! */
+ if (!err)
+ return 0;
+
+ /* EIO means MSI test failed */
+ if (err != -EIO)
+ return err;
+
+ /* back to INTx mode */
+ e_warn("MSI interrupt test failed, using legacy interrupt.\n");
+
+ e1000_free_irq(adapter);
+
+ err = e1000_request_irq(adapter);
+
+ return err;
+}
+
+/**
+ * e1000_open - Called when a network interface is made active
+ * @netdev: network interface device structure
+ *
+ * Returns 0 on success, negative value on failure
+ *
+ * The open entry point is called when a network interface is made
+ * active by the system (IFF_UP). At this point all resources needed
+ * for transmit and receive operations are allocated, the interrupt
+ * handler is registered with the OS, the watchdog timer is started,
+ * and the stack is notified that the interface is ready.
+ **/
+static int e1000_open(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ int err;
+
+ /* disallow open during test */
+ if (test_bit(__E1000_TESTING, &adapter->state))
+ return -EBUSY;
+
+ /* allocate transmit descriptors */
+ err = e1000e_setup_tx_resources(adapter);
+ if (err)
+ goto err_setup_tx;
+
+ /* allocate receive descriptors */
+ err = e1000e_setup_rx_resources(adapter);
+ if (err)
+ goto err_setup_rx;
+
+ e1000e_power_up_phy(adapter);
+
+ adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
+ if ((adapter->hw.mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN))
+ e1000_update_mng_vlan(adapter);
+
+ /*
+ * If AMT is enabled, let the firmware know that the network
+ * interface is now open
+ */
+ if (adapter->flags & FLAG_HAS_AMT)
+ e1000_get_hw_control(adapter);
+
+ /*
+ * before we allocate an interrupt, we must be ready to handle it.
+ * Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt
+ * as soon as we call pci_request_irq, so we have to setup our
+ * clean_rx handler before we do so.
+ */
+ e1000_configure(adapter);
+
+ err = e1000_request_irq(adapter);
+ if (err)
+ goto err_req_irq;
+
+ /*
+ * Work around PCIe errata with MSI interrupts causing some chipsets to
+ * ignore e1000e MSI messages, which means we need to test our MSI
+ * interrupt now
+ */
+ err = e1000_test_msi(adapter);
+ if (err) {
+ e_err("Interrupt allocation failed\n");
+ goto err_req_irq;
+ }
+
+ /*
+ * Work around PCIe errata with MSI interrupts causing some chipsets to
+ * ignore e1000e MSI messages, which means we need to test our MSI
+ * interrupt now
+ */
+ if (adapter->int_mode != E1000E_INT_MODE_LEGACY) {
+ err = e1000_test_msi(adapter);
+ if (err) {
+ e_err("Interrupt allocation failed\n");
+ goto err_req_irq;
+ }
+ }
+
+ /* From here on the code is the same as e1000e_up() */
+ clear_bit(__E1000_DOWN, &adapter->state);
+
+ netif_poll_enable(netdev);
+
+ e1000_irq_enable(adapter);
+
+ /* fire a link status change interrupt to start the watchdog */
+ ew32(ICS, E1000_ICS_LSC);
+
+ return 0;
+
+err_req_irq:
+ e1000_release_hw_control(adapter);
+ e1000_power_down_phy(adapter);
+ e1000e_free_rx_resources(adapter);
+err_setup_rx:
+ e1000e_free_tx_resources(adapter);
+err_setup_tx:
+ e1000e_reset(adapter);
+
+ return err;
+}
+
+/**
+ * e1000_close - Disables a network interface
+ * @netdev: network interface device structure
+ *
+ * Returns 0, this is not allowed to fail
+ *
+ * The close entry point is called when an interface is de-activated
+ * by the OS. The hardware is still under the drivers control, but
+ * needs to be disabled. A global MAC reset is issued to stop the
+ * hardware, and all transmit and receive resources are freed.
+ **/
+static int e1000_close(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ WARN_ON(test_bit(__E1000_RESETTING, &adapter->state));
+ e1000e_down(adapter);
+ e1000_power_down_phy(adapter);
+ e1000_free_irq(adapter);
+
+ e1000e_free_tx_resources(adapter);
+ e1000e_free_rx_resources(adapter);
+
+ /*
+ * kill manageability vlan ID if supported, but not if a vlan with
+ * the same ID is registered on the host OS (let 8021q kill it)
+ */
+ if ((adapter->hw.mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN) &&
+ !(adapter->vlgrp &&
+ vlan_group_get_device(adapter->vlgrp, adapter->mng_vlan_id)))
+ e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id);
+
+ /*
+ * If AMT is enabled, let the firmware know that the network
+ * interface is now closed
+ */
+ if (adapter->flags & FLAG_HAS_AMT)
+ e1000_release_hw_control(adapter);
+
+ return 0;
+}
+/**
+ * e1000_set_mac - Change the Ethernet Address of the NIC
+ * @netdev: network interface device structure
+ * @p: pointer to an address structure
+ *
+ * Returns 0 on success, negative on failure
+ **/
+static int e1000_set_mac(struct net_device *netdev, void *p)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct sockaddr *addr = p;
+
+ if (!is_valid_ether_addr(addr->sa_data))
+ return -EADDRNOTAVAIL;
+
+ memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
+ memcpy(adapter->hw.mac.addr, addr->sa_data, netdev->addr_len);
+
+ e1000e_rar_set(&adapter->hw, adapter->hw.mac.addr, 0);
+
+ if (adapter->flags & FLAG_RESET_OVERWRITES_LAA) {
+ /* activate the work around */
+ e1000e_set_laa_state_82571(&adapter->hw, 1);
+
+ /*
+ * Hold a copy of the LAA in RAR[14] This is done so that
+ * between the time RAR[0] gets clobbered and the time it
+ * gets fixed (in e1000_watchdog), the actual LAA is in one
+ * of the RARs and no incoming packets directed to this port
+ * are dropped. Eventually the LAA will be in RAR[0] and
+ * RAR[14]
+ */
+ e1000e_rar_set(&adapter->hw,
+ adapter->hw.mac.addr,
+ adapter->hw.mac.rar_entry_count - 1);
+ }
+
+ return 0;
+}
+
+/*
+ * Need to wait a few seconds after link up to get diagnostic information from
+ * the phy
+ */
+static void e1000_update_phy_info(unsigned long data)
+{
+ struct e1000_adapter *adapter = (struct e1000_adapter *) data;
+ e1000_get_phy_info(&adapter->hw);
+}
+
+/**
+ * e1000e_update_stats - Update the board statistics counters
+ * @adapter: board private structure
+ **/
+void e1000e_update_stats(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct pci_dev *pdev = adapter->pdev;
+ unsigned long irq_flags;
+ u16 phy_tmp;
+
+#define PHY_IDLE_ERROR_COUNT_MASK 0x00FF
+
+ /*
+ * Prevent stats update while adapter is being reset, or if the pci
+ * connection is down.
+ */
+ if (adapter->link_speed == 0)
+ return;
+ if (pdev->error_state && pdev->error_state != pci_channel_io_normal)
+ return;
+
+ spin_lock_irqsave(&adapter->stats_lock, irq_flags);
+
+ /*
+ * these counters are modified from e1000_adjust_tbi_stats,
+ * called from the interrupt context, so they must only
+ * be written while holding adapter->stats_lock
+ */
+
+ adapter->stats.crcerrs += er32(CRCERRS);
+ adapter->stats.gprc += er32(GPRC);
+ adapter->stats.gorc += er32(GORCL);
+ er32(GORCH); /* Clear gorc */
+ adapter->stats.bprc += er32(BPRC);
+ adapter->stats.mprc += er32(MPRC);
+ adapter->stats.roc += er32(ROC);
+
+ adapter->stats.mpc += er32(MPC);
+ adapter->stats.scc += er32(SCC);
+ adapter->stats.ecol += er32(ECOL);
+ adapter->stats.mcc += er32(MCC);
+ adapter->stats.latecol += er32(LATECOL);
+ adapter->stats.dc += er32(DC);
+ adapter->stats.xonrxc += er32(XONRXC);
+ adapter->stats.xontxc += er32(XONTXC);
+ adapter->stats.xoffrxc += er32(XOFFRXC);
+ adapter->stats.xofftxc += er32(XOFFTXC);
+ adapter->stats.gptc += er32(GPTC);
+ adapter->stats.gotc += er32(GOTCL);
+ er32(GOTCH); /* Clear gotc */
+ adapter->stats.rnbc += er32(RNBC);
+ adapter->stats.ruc += er32(RUC);
+
+ adapter->stats.mptc += er32(MPTC);
+ adapter->stats.bptc += er32(BPTC);
+
+ /* used for adaptive IFS */
+
+ hw->mac.tx_packet_delta = er32(TPT);
+ adapter->stats.tpt += hw->mac.tx_packet_delta;
+ hw->mac.collision_delta = er32(COLC);
+ adapter->stats.colc += hw->mac.collision_delta;
+
+ adapter->stats.algnerrc += er32(ALGNERRC);
+ adapter->stats.rxerrc += er32(RXERRC);
+ if (hw->mac.type != e1000_82574)
+ adapter->stats.tncrs += er32(TNCRS);
+ adapter->stats.cexterr += er32(CEXTERR);
+ adapter->stats.tsctc += er32(TSCTC);
+ adapter->stats.tsctfc += er32(TSCTFC);
+
+ /* Fill out the OS statistics structure */
+ adapter->net_stats.multicast = adapter->stats.mprc;
+ adapter->net_stats.collisions = adapter->stats.colc;
+
+ /* Rx Errors */
+
+ /*
+ * RLEC on some newer hardware can be incorrect so build
+ * our own version based on RUC and ROC
+ */
+ adapter->net_stats.rx_errors = adapter->stats.rxerrc +
+ adapter->stats.crcerrs + adapter->stats.algnerrc +
+ adapter->stats.ruc + adapter->stats.roc +
+ adapter->stats.cexterr;
+ adapter->net_stats.rx_length_errors = adapter->stats.ruc +
+ adapter->stats.roc;
+ adapter->net_stats.rx_crc_errors = adapter->stats.crcerrs;
+ adapter->net_stats.rx_frame_errors = adapter->stats.algnerrc;
+ adapter->net_stats.rx_missed_errors = adapter->stats.mpc;
+
+ /* Tx Errors */
+ adapter->net_stats.tx_errors = adapter->stats.ecol +
+ adapter->stats.latecol;
+ adapter->net_stats.tx_aborted_errors = adapter->stats.ecol;
+ adapter->net_stats.tx_window_errors = adapter->stats.latecol;
+ adapter->net_stats.tx_carrier_errors = adapter->stats.tncrs;
+
+ /* Tx Dropped needs to be maintained elsewhere */
+
+ /* Phy Stats */
+ if (hw->phy.media_type == e1000_media_type_copper) {
+ if ((adapter->link_speed == SPEED_1000) &&
+ (!e1e_rphy(hw, PHY_1000T_STATUS, &phy_tmp))) {
+ phy_tmp &= PHY_IDLE_ERROR_COUNT_MASK;
+ adapter->phy_stats.idle_errors += phy_tmp;
+ }
+ }
+
+ /* Management Stats */
+ adapter->stats.mgptc += er32(MGTPTC);
+ adapter->stats.mgprc += er32(MGTPRC);
+ adapter->stats.mgpdc += er32(MGTPDC);
+ spin_unlock_irqrestore(&adapter->stats_lock, irq_flags);
+}
+
+/**
+ * e1000_phy_read_status - Update the PHY register status snapshot
+ * @adapter: board private structure
+ **/
+static void e1000_phy_read_status(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct e1000_phy_regs *phy = &adapter->phy_regs;
+ int ret_val;
+ unsigned long irq_flags;
+
+
+ spin_lock_irqsave(&adapter->stats_lock, irq_flags);
+
+ if ((er32(STATUS) & E1000_STATUS_LU) &&
+ (adapter->hw.phy.media_type == e1000_media_type_copper)) {
+ ret_val = e1e_rphy(hw, PHY_CONTROL, &phy->bmcr);
+ ret_val |= e1e_rphy(hw, PHY_STATUS, &phy->bmsr);
+ ret_val |= e1e_rphy(hw, PHY_AUTONEG_ADV, &phy->advertise);
+ ret_val |= e1e_rphy(hw, PHY_LP_ABILITY, &phy->lpa);
+ ret_val |= e1e_rphy(hw, PHY_AUTONEG_EXP, &phy->expansion);
+ ret_val |= e1e_rphy(hw, PHY_1000T_CTRL, &phy->ctrl1000);
+ ret_val |= e1e_rphy(hw, PHY_1000T_STATUS, &phy->stat1000);
+ ret_val |= e1e_rphy(hw, PHY_EXT_STATUS, &phy->estatus);
+ if (ret_val)
+ e_warn("Error reading PHY register\n");
+ } else {
+ /*
+ * Do not read PHY registers if link is not up
+ * Set values to typical power-on defaults
+ */
+ phy->bmcr = (BMCR_SPEED1000 | BMCR_ANENABLE | BMCR_FULLDPLX);
+ phy->bmsr = (BMSR_100FULL | BMSR_100HALF | BMSR_10FULL |
+ BMSR_10HALF | BMSR_ESTATEN | BMSR_ANEGCAPABLE |
+ BMSR_ERCAP);
+ phy->advertise = (ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP |
+ ADVERTISE_ALL | ADVERTISE_CSMA);
+ phy->lpa = 0;
+ phy->expansion = EXPANSION_ENABLENPAGE;
+ phy->ctrl1000 = ADVERTISE_1000FULL;
+ phy->stat1000 = 0;
+ phy->estatus = (ESTATUS_1000_TFULL | ESTATUS_1000_THALF);
+ }
+
+ spin_unlock_irqrestore(&adapter->stats_lock, irq_flags);
+}
+
+static void e1000_print_link_info(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl = er32(CTRL);
+
+ e_info("Link is Up %d Mbps %s, Flow Control: %s\n",
+ adapter->link_speed,
+ (adapter->link_duplex == FULL_DUPLEX) ?
+ "Full Duplex" : "Half Duplex",
+ ((ctrl & E1000_CTRL_TFCE) && (ctrl & E1000_CTRL_RFCE)) ?
+ "RX/TX" :
+ ((ctrl & E1000_CTRL_RFCE) ? "RX" :
+ ((ctrl & E1000_CTRL_TFCE) ? "TX" : "None" )));
+}
+
+static bool e1000_has_link(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ bool link_active = 0;
+ s32 ret_val = 0;
+
+ /*
+ * get_link_status is set on LSC (link status) interrupt or
+ * Rx sequence error interrupt. get_link_status will stay
+ * false until the check_for_link establishes link
+ * for copper adapters ONLY
+ */
+ switch (hw->phy.media_type) {
+ case e1000_media_type_copper:
+ if (hw->mac.get_link_status) {
+ ret_val = hw->mac.ops.check_for_link(hw);
+ link_active = !hw->mac.get_link_status;
+ } else {
+ link_active = 1;
+ }
+ break;
+ case e1000_media_type_fiber:
+ ret_val = hw->mac.ops.check_for_link(hw);
+ link_active = !!(er32(STATUS) & E1000_STATUS_LU);
+ break;
+ case e1000_media_type_internal_serdes:
+ ret_val = hw->mac.ops.check_for_link(hw);
+ link_active = adapter->hw.mac.serdes_has_link;
+ break;
+ default:
+ case e1000_media_type_unknown:
+ break;
+ }
+
+ if ((ret_val == E1000_ERR_PHY) && (hw->phy.type == e1000_phy_igp_3) &&
+ (er32(CTRL) & E1000_PHY_CTRL_GBE_DISABLE)) {
+ /* See e1000_kmrn_lock_loss_workaround_ich8lan() */
+ e_info("Gigabit has been disabled, downgrading speed\n");
+ }
+
+ return link_active;
+}
+
+static void e1000e_enable_receives(struct e1000_adapter *adapter)
+{
+ /* make sure the receive unit is started */
+ if ((adapter->flags & FLAG_RX_NEEDS_RESTART) &&
+ (adapter->flags & FLAG_RX_RESTART_NOW)) {
+ struct e1000_hw *hw = &adapter->hw;
+ u32 rctl = er32(RCTL);
+ ew32(RCTL, rctl | E1000_RCTL_EN);
+ adapter->flags &= ~FLAG_RX_RESTART_NOW;
+ }
+}
+
+/**
+ * e1000_watchdog - Timer Call-back
+ * @data: pointer to adapter cast into an unsigned long
+ **/
+static void e1000_watchdog(unsigned long data)
+{
+ struct e1000_adapter *adapter = (struct e1000_adapter *) data;
+
+ /* Do the rest outside of interrupt context */
+ schedule_work(&adapter->watchdog_task);
+
+ /* TODO: make this use queue_delayed_work() */
+}
+
+static void e1000_watchdog_task(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_mac_info *mac = &adapter->hw.mac;
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ struct e1000_hw *hw = &adapter->hw;
+ u32 link, tctl;
+ int tx_pending = 0;
+
+ link = e1000_has_link(adapter);
+ if ((netif_carrier_ok(netdev)) && link) {
+ e1000e_enable_receives(adapter);
+ goto link_up;
+ }
+
+ if ((e1000e_enable_tx_pkt_filtering(hw)) &&
+ (adapter->mng_vlan_id != adapter->hw.mng_cookie.vlan_id))
+ e1000_update_mng_vlan(adapter);
+
+ if (link) {
+ if (!netif_carrier_ok(netdev)) {
+ bool txb2b = 1;
+ /* update snapshot of PHY registers on LSC */
+ e1000_phy_read_status(adapter);
+ mac->ops.get_link_up_info(&adapter->hw,
+ &adapter->link_speed,
+ &adapter->link_duplex);
+ e1000_print_link_info(adapter);
+ /*
+ * On supported PHYs, check for duplex mismatch only
+ * if link has autonegotiated at 10/100 half
+ */
+ if ((hw->phy.type == e1000_phy_igp_3 ||
+ hw->phy.type == e1000_phy_bm) &&
+ (hw->mac.autoneg == true) &&
+ (adapter->link_speed == SPEED_10 ||
+ adapter->link_speed == SPEED_100) &&
+ (adapter->link_duplex == HALF_DUPLEX)) {
+ u16 autoneg_exp;
+
+ e1e_rphy(hw, PHY_AUTONEG_EXP, &autoneg_exp);
+
+ if (!(autoneg_exp & NWAY_ER_LP_NWAY_CAPS))
+ e_info("Autonegotiated half duplex but"
+ " link partner cannot autoneg. "
+ " Try forcing full duplex if "
+ "link gets many collisions.\n");
+ }
+
+ /*
+ * tweak tx_queue_len according to speed/duplex
+ * and adjust the timeout factor
+ */
+ netdev->tx_queue_len = adapter->tx_queue_len;
+ adapter->tx_timeout_factor = 1;
+ switch (adapter->link_speed) {
+ case SPEED_10:
+ txb2b = 0;
+ netdev->tx_queue_len = 10;
+ adapter->tx_timeout_factor = 16;
+ break;
+ case SPEED_100:
+ txb2b = 0;
+ netdev->tx_queue_len = 100;
+ /* maybe add some timeout factor ? */
+ break;
+ }
+
+ /*
+ * workaround: re-program speed mode bit after
+ * link-up event
+ */
+ if ((adapter->flags & FLAG_TARC_SPEED_MODE_BIT) &&
+ !txb2b) {
+ u32 tarc0;
+ tarc0 = er32(TARC(0));
+ tarc0 &= ~SPEED_MODE_BIT;
+ ew32(TARC(0), tarc0);
+ }
+
+ /*
+ * disable TSO for pcie and 10/100 speeds, to avoid
+ * some hardware issues
+ */
+ if (!(adapter->flags & FLAG_TSO_FORCE)) {
+ switch (adapter->link_speed) {
+ case SPEED_10:
+ case SPEED_100:
+ e_info("10/100 speed: disabling TSO\n");
+ netdev->features &= ~NETIF_F_TSO;
+ netdev->features &= ~NETIF_F_TSO6;
+ break;
+ case SPEED_1000:
+ netdev->features |= NETIF_F_TSO;
+ netdev->features |= NETIF_F_TSO6;
+ break;
+ default:
+ /* oops */
+ break;
+ }
+ }
+
+ /*
+ * enable transmits in the hardware, need to do this
+ * after setting TARC(0)
+ */
+ tctl = er32(TCTL);
+ tctl |= E1000_TCTL_EN;
+ ew32(TCTL, tctl);
+
+ netif_carrier_on(netdev);
+ netif_wake_queue(netdev);
+
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ mod_timer(&adapter->phy_info_timer,
+ round_jiffies(jiffies + 2 * HZ));
+ }
+ } else {
+ if (netif_carrier_ok(netdev)) {
+ adapter->link_speed = 0;
+ adapter->link_duplex = 0;
+ e_info("Link is Down\n");
+ netif_carrier_off(netdev);
+ netif_stop_queue(netdev);
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ mod_timer(&adapter->phy_info_timer,
+ round_jiffies(jiffies + 2 * HZ));
+
+ if (adapter->flags & FLAG_RX_NEEDS_RESTART)
+ schedule_work(&adapter->reset_task);
+ }
+ }
+
+link_up:
+ e1000e_update_stats(adapter);
+
+ mac->tx_packet_delta = adapter->stats.tpt - adapter->tpt_old;
+ adapter->tpt_old = adapter->stats.tpt;
+ mac->collision_delta = adapter->stats.colc - adapter->colc_old;
+ adapter->colc_old = adapter->stats.colc;
+
+ adapter->gorc = adapter->stats.gorc - adapter->gorc_old;
+ adapter->gorc_old = adapter->stats.gorc;
+ adapter->gotc = adapter->stats.gotc - adapter->gotc_old;
+ adapter->gotc_old = adapter->stats.gotc;
+
+ e1000e_update_adaptive(&adapter->hw);
+
+ if (!netif_carrier_ok(netdev)) {
+ tx_pending = (e1000_desc_unused(tx_ring) + 1 <
+ tx_ring->count);
+ if (tx_pending) {
+ /*
+ * We've lost link, so the controller stops DMA,
+ * but we've got queued Tx work that's never going
+ * to get done, so reset controller to flush Tx.
+ * (Do the reset outside of interrupt context).
+ */
+ adapter->tx_timeout_count++;
+ schedule_work(&adapter->reset_task);
+ }
+ }
+
+ /* Cause software interrupt to ensure Rx ring is cleaned */
+ if (adapter->msix_entries)
+ ew32(ICS, adapter->rx_ring->ims_val);
+ else
+ ew32(ICS, E1000_ICS_RXDMT0);
+
+ /* Force detection of hung controller every watchdog period */
+ adapter->detect_tx_hung = 1;
+
+ /*
+ * With 82571 controllers, LAA may be overwritten due to controller
+ * reset from the other port. Set the appropriate LAA in RAR[0]
+ */
+ if (e1000e_get_laa_state_82571(hw))
+ e1000e_rar_set(hw, adapter->hw.mac.addr, 0);
+
+ /* Reset the timer */
+ if (!test_bit(__E1000_DOWN, &adapter->state))
+ mod_timer(&adapter->watchdog_timer,
+ round_jiffies(jiffies + 2 * HZ));
+}
+
+#define E1000_TX_FLAGS_CSUM 0x00000001
+#define E1000_TX_FLAGS_VLAN 0x00000002
+#define E1000_TX_FLAGS_TSO 0x00000004
+#define E1000_TX_FLAGS_IPV4 0x00000008
+#define E1000_TX_FLAGS_VLAN_MASK 0xffff0000
+#define E1000_TX_FLAGS_VLAN_SHIFT 16
+
+static int e1000_tso(struct e1000_adapter *adapter,
+ struct sk_buff *skb)
+{
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ struct e1000_context_desc *context_desc;
+ struct e1000_buffer *buffer_info;
+ unsigned int i;
+ u32 cmd_length = 0;
+ u16 ipcse = 0, tucse, mss;
+ u8 ipcss, ipcso, tucss, tucso, hdr_len;
+ int err;
+
+ if (skb_is_gso(skb)) {
+ if (skb_header_cloned(skb)) {
+ err = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
+ if (err)
+ return err;
+ }
+
+ hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
+ mss = skb_shinfo(skb)->gso_size;
+ if (skb->protocol == htons(ETH_P_IP)) {
+ struct iphdr *iph = ip_hdr(skb);
+ iph->tot_len = 0;
+ iph->check = 0;
+ tcp_hdr(skb)->check = ~csum_tcpudp_magic(iph->saddr,
+ iph->daddr, 0,
+ IPPROTO_TCP,
+ 0);
+ cmd_length = E1000_TXD_CMD_IP;
+ ipcse = skb_transport_offset(skb) - 1;
+ } else if (skb_shinfo(skb)->gso_type == SKB_GSO_TCPV6) {
+ ipv6_hdr(skb)->payload_len = 0;
+ tcp_hdr(skb)->check =
+ ~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
+ &ipv6_hdr(skb)->daddr,
+ 0, IPPROTO_TCP, 0);
+ ipcse = 0;
+ }
+ ipcss = skb_network_offset(skb);
+ ipcso = (void *)&(ip_hdr(skb)->check) - (void *)skb->data;
+ tucss = skb_transport_offset(skb);
+ tucso = (void *)&(tcp_hdr(skb)->check) - (void *)skb->data;
+ tucse = 0;
+
+ cmd_length |= (E1000_TXD_CMD_DEXT | E1000_TXD_CMD_TSE |
+ E1000_TXD_CMD_TCP | (skb->len - (hdr_len)));
+
+ i = tx_ring->next_to_use;
+ context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
+ buffer_info = &tx_ring->buffer_info[i];
+
+ context_desc->lower_setup.ip_fields.ipcss = ipcss;
+ context_desc->lower_setup.ip_fields.ipcso = ipcso;
+ context_desc->lower_setup.ip_fields.ipcse = cpu_to_le16(ipcse);
+ context_desc->upper_setup.tcp_fields.tucss = tucss;
+ context_desc->upper_setup.tcp_fields.tucso = tucso;
+ context_desc->upper_setup.tcp_fields.tucse = cpu_to_le16(tucse);
+ context_desc->tcp_seg_setup.fields.mss = cpu_to_le16(mss);
+ context_desc->tcp_seg_setup.fields.hdr_len = hdr_len;
+ context_desc->cmd_and_length = cpu_to_le32(cmd_length);
+
+ buffer_info->time_stamp = jiffies;
+ buffer_info->next_to_watch = i;
+
+ i++;
+ if (i == tx_ring->count)
+ i = 0;
+ tx_ring->next_to_use = i;
+
+ return 1;
+ }
+
+ return 0;
+}
+
+static bool e1000_tx_csum(struct e1000_adapter *adapter, struct sk_buff *skb)
+{
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ struct e1000_context_desc *context_desc;
+ struct e1000_buffer *buffer_info;
+ unsigned int i;
+ u8 css;
+
+ if (skb->ip_summed == CHECKSUM_PARTIAL) {
+ css = skb_transport_offset(skb);
+
+ i = tx_ring->next_to_use;
+ buffer_info = &tx_ring->buffer_info[i];
+ context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
+
+ context_desc->lower_setup.ip_config = 0;
+ context_desc->upper_setup.tcp_fields.tucss = css;
+ context_desc->upper_setup.tcp_fields.tucso = css + skb->csum;
+ context_desc->upper_setup.tcp_fields.tucse = 0;
+ context_desc->tcp_seg_setup.data = 0;
+ context_desc->cmd_and_length = cpu_to_le32(E1000_TXD_CMD_DEXT);
+
+ buffer_info->time_stamp = jiffies;
+ buffer_info->next_to_watch = i;
+
+ i++;
+ if (i == tx_ring->count)
+ i = 0;
+ tx_ring->next_to_use = i;
+
+ return 1;
+ }
+
+ return 0;
+}
+
+#define E1000_MAX_PER_TXD 8192
+#define E1000_MAX_TXD_PWR 12
+
+static int e1000_tx_map(struct e1000_adapter *adapter,
+ struct sk_buff *skb, unsigned int first,
+ unsigned int max_per_txd, unsigned int nr_frags,
+ unsigned int mss)
+{
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ struct e1000_buffer *buffer_info;
+ unsigned int len = skb->len - skb->data_len;
+ unsigned int offset = 0, size, count = 0, i;
+ unsigned int f;
+
+ i = tx_ring->next_to_use;
+
+ while (len) {
+ buffer_info = &tx_ring->buffer_info[i];
+ size = min(len, max_per_txd);
+
+ /* Workaround for premature desc write-backs
+ * in TSO mode. Append 4-byte sentinel desc */
+ if (mss && !nr_frags && size == len && size > 8)
+ size -= 4;
+
+ buffer_info->length = size;
+ /* set time_stamp *before* dma to help avoid a possible race */
+ buffer_info->time_stamp = jiffies;
+ buffer_info->dma =
+ pci_map_single(adapter->pdev,
+ skb->data + offset,
+ size,
+ PCI_DMA_TODEVICE);
+ if (pci_dma_mapping_error(buffer_info->dma)) {
+ dev_err(&adapter->pdev->dev, "TX DMA map failed\n");
+ adapter->tx_dma_failed++;
+ return -1;
+ }
+ buffer_info->next_to_watch = i;
+
+ len -= size;
+ offset += size;
+ count++;
+ i++;
+ if (i == tx_ring->count)
+ i = 0;
+ }
+
+ for (f = 0; f < nr_frags; f++) {
+ struct skb_frag_struct *frag;
+
+ frag = &skb_shinfo(skb)->frags[f];
+ len = frag->size;
+ offset = frag->page_offset;
+
+ while (len) {
+ buffer_info = &tx_ring->buffer_info[i];
+ size = min(len, max_per_txd);
+ /* Workaround for premature desc write-backs
+ * in TSO mode. Append 4-byte sentinel desc */
+ if (mss && f == (nr_frags-1) && size == len && size > 8)
+ size -= 4;
+
+ buffer_info->length = size;
+ buffer_info->time_stamp = jiffies;
+ buffer_info->dma =
+ pci_map_page(adapter->pdev,
+ frag->page,
+ offset,
+ size,
+ PCI_DMA_TODEVICE);
+ if (pci_dma_mapping_error(buffer_info->dma)) {
+ dev_err(&adapter->pdev->dev,
+ "TX DMA page map failed\n");
+ adapter->tx_dma_failed++;
+ return -1;
+ }
+
+ buffer_info->next_to_watch = i;
+
+ len -= size;
+ offset += size;
+ count++;
+
+ i++;
+ if (i == tx_ring->count)
+ i = 0;
+ }
+ }
+
+ if (i == 0)
+ i = tx_ring->count - 1;
+ else
+ i--;
+
+ tx_ring->buffer_info[i].skb = skb;
+ tx_ring->buffer_info[first].next_to_watch = i;
+
+ return count;
+}
+
+static void e1000_tx_queue(struct e1000_adapter *adapter,
+ int tx_flags, int count)
+{
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ struct e1000_tx_desc *tx_desc = NULL;
+ struct e1000_buffer *buffer_info;
+ u32 txd_upper = 0, txd_lower = E1000_TXD_CMD_IFCS;
+ unsigned int i;
+
+ if (tx_flags & E1000_TX_FLAGS_TSO) {
+ txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D |
+ E1000_TXD_CMD_TSE;
+ txd_upper |= E1000_TXD_POPTS_TXSM << 8;
+
+ if (tx_flags & E1000_TX_FLAGS_IPV4)
+ txd_upper |= E1000_TXD_POPTS_IXSM << 8;
+ }
+
+ if (tx_flags & E1000_TX_FLAGS_CSUM) {
+ txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D;
+ txd_upper |= E1000_TXD_POPTS_TXSM << 8;
+ }
+
+ if (tx_flags & E1000_TX_FLAGS_VLAN) {
+ txd_lower |= E1000_TXD_CMD_VLE;
+ txd_upper |= (tx_flags & E1000_TX_FLAGS_VLAN_MASK);
+ }
+
+ i = tx_ring->next_to_use;
+
+ while (count--) {
+ buffer_info = &tx_ring->buffer_info[i];
+ tx_desc = E1000_TX_DESC(*tx_ring, i);
+ tx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
+ tx_desc->lower.data =
+ cpu_to_le32(txd_lower | buffer_info->length);
+ tx_desc->upper.data = cpu_to_le32(txd_upper);
+
+ i++;
+ if (i == tx_ring->count)
+ i = 0;
+ }
+
+ tx_desc->lower.data |= cpu_to_le32(adapter->txd_cmd);
+
+ /*
+ * Force memory writes to complete before letting h/w
+ * know there are new descriptors to fetch. (Only
+ * applicable for weak-ordered memory model archs,
+ * such as IA-64).
+ */
+ wmb();
+
+ tx_ring->next_to_use = i;
+ writel(i, adapter->hw.hw_addr + tx_ring->tail);
+ /*
+ * we need this if more than one processor can write to our tail
+ * at a time, it synchronizes IO on IA64/Altix systems
+ */
+ mmiowb();
+}
+
+#define MINIMUM_DHCP_PACKET_SIZE 282
+static int e1000_transfer_dhcp_info(struct e1000_adapter *adapter,
+ struct sk_buff *skb)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ u16 length, offset;
+
+ if (vlan_tx_tag_present(skb)) {
+ if (!((vlan_tx_tag_get(skb) == adapter->hw.mng_cookie.vlan_id)
+ && (adapter->hw.mng_cookie.status &
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN)))
+ return 0;
+ }
+
+ if (skb->len <= MINIMUM_DHCP_PACKET_SIZE)
+ return 0;
+
+ if (((struct ethhdr *) skb->data)->h_proto != htons(ETH_P_IP))
+ return 0;
+
+ {
+ const struct iphdr *ip = (struct iphdr *)((u8 *)skb->data+14);
+ struct udphdr *udp;
+
+ if (ip->protocol != IPPROTO_UDP)
+ return 0;
+
+ udp = (struct udphdr *)((u8 *)ip + (ip->ihl << 2));
+ if (ntohs(udp->dest) != 67)
+ return 0;
+
+ offset = (u8 *)udp + 8 - skb->data;
+ length = skb->len - offset;
+ return e1000e_mng_write_dhcp_info(hw, (u8 *)udp + 8, length);
+ }
+
+ return 0;
+}
+
+static int __e1000_maybe_stop_tx(struct net_device *netdev, int size)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ netif_stop_queue(netdev);
+ /*
+ * Herbert's original patch had:
+ * smp_mb__after_netif_stop_queue();
+ * but since that doesn't exist yet, just open code it.
+ */
+ smp_mb();
+
+ /*
+ * We need to check again in a case another CPU has just
+ * made room available.
+ */
+ if (e1000_desc_unused(adapter->tx_ring) < size)
+ return -EBUSY;
+
+ /* A reprieve! */
+ netif_start_queue(netdev);
+ ++adapter->restart_queue;
+ return 0;
+}
+
+static int e1000_maybe_stop_tx(struct net_device *netdev, int size)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ if (e1000_desc_unused(adapter->tx_ring) >= size)
+ return 0;
+ return __e1000_maybe_stop_tx(netdev, size);
+}
+
+#define TXD_USE_COUNT(S, X) (((S) >> (X)) + 1 )
+static int e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_ring *tx_ring = adapter->tx_ring;
+ unsigned int first;
+ unsigned int max_per_txd = E1000_MAX_PER_TXD;
+ unsigned int max_txd_pwr = E1000_MAX_TXD_PWR;
+ unsigned int tx_flags = 0;
+ unsigned int len = skb->len - skb->data_len;
+ unsigned long irq_flags;
+ unsigned int nr_frags;
+ unsigned int mss;
+ int count = 0;
+ int tso;
+ unsigned int f;
+
+ if (test_bit(__E1000_DOWN, &adapter->state)) {
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+ }
+
+ if (skb->len <= 0) {
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+ }
+
+ mss = skb_shinfo(skb)->gso_size;
+ /*
+ * The controller does a simple calculation to
+ * make sure there is enough room in the FIFO before
+ * initiating the DMA for each buffer. The calc is:
+ * 4 = ceil(buffer len/mss). To make sure we don't
+ * overrun the FIFO, adjust the max buffer len if mss
+ * drops.
+ */
+ if (mss) {
+ u8 hdr_len;
+ max_per_txd = min(mss << 2, max_per_txd);
+ max_txd_pwr = fls(max_per_txd) - 1;
+
+ /*
+ * TSO Workaround for 82571/2/3 Controllers -- if skb->data
+ * points to just header, pull a few bytes of payload from
+ * frags into skb->data
+ */
+ hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
+ /*
+ * we do this workaround for ES2LAN, but it is un-necessary,
+ * avoiding it could save a lot of cycles
+ */
+ if (skb->data_len && (hdr_len == len)) {
+ unsigned int pull_size;
+
+ pull_size = min((unsigned int)4, skb->data_len);
+ if (!__pskb_pull_tail(skb, pull_size)) {
+ e_err("__pskb_pull_tail failed.\n");
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+ }
+ len = skb->len - skb->data_len;
+ }
+ }
+
+ /* reserve a descriptor for the offload context */
+ if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL))
+ count++;
+ count++;
+
+ count += TXD_USE_COUNT(len, max_txd_pwr);
+
+ nr_frags = skb_shinfo(skb)->nr_frags;
+ for (f = 0; f < nr_frags; f++)
+ count += TXD_USE_COUNT(skb_shinfo(skb)->frags[f].size,
+ max_txd_pwr);
+
+ if (adapter->hw.mac.tx_pkt_filtering)
+ e1000_transfer_dhcp_info(adapter, skb);
+
+ if (!spin_trylock_irqsave(&adapter->tx_queue_lock, irq_flags))
+ /* Collision - tell upper layer to requeue */
+ return NETDEV_TX_LOCKED;
+
+ /*
+ * need: count + 2 desc gap to keep tail from touching
+ * head, otherwise try next time
+ */
+ if (e1000_maybe_stop_tx(netdev, count + 2)) {
+ spin_unlock_irqrestore(&adapter->tx_queue_lock, irq_flags);
+ return NETDEV_TX_BUSY;
+ }
+
+ if (adapter->vlgrp && vlan_tx_tag_present(skb)) {
+ tx_flags |= E1000_TX_FLAGS_VLAN;
+ tx_flags |= (vlan_tx_tag_get(skb) << E1000_TX_FLAGS_VLAN_SHIFT);
+ }
+
+ first = tx_ring->next_to_use;
+
+ tso = e1000_tso(adapter, skb);
+ if (tso < 0) {
+ dev_kfree_skb_any(skb);
+ spin_unlock_irqrestore(&adapter->tx_queue_lock, irq_flags);
+ return NETDEV_TX_OK;
+ }
+
+ if (tso)
+ tx_flags |= E1000_TX_FLAGS_TSO;
+ else if (e1000_tx_csum(adapter, skb))
+ tx_flags |= E1000_TX_FLAGS_CSUM;
+
+ /*
+ * Old method was to assume IPv4 packet by default if TSO was enabled.
+ * 82571 hardware supports TSO capabilities for IPv6 as well...
+ * no longer assume, we must.
+ */
+ if (skb->protocol == htons(ETH_P_IP))
+ tx_flags |= E1000_TX_FLAGS_IPV4;
+
+ count = e1000_tx_map(adapter, skb, first, max_per_txd, nr_frags, mss);
+ if (count < 0) {
+ /* handle pci_map_single() error in e1000_tx_map */
+ dev_kfree_skb_any(skb);
+ spin_unlock_irqrestore(&adapter->tx_queue_lock, irq_flags);
+ return NETDEV_TX_OK;
+ }
+
+ e1000_tx_queue(adapter, tx_flags, count);
+
+ netdev->trans_start = jiffies;
+
+ /* Make sure there is space in the ring for the next send. */
+ e1000_maybe_stop_tx(netdev, MAX_SKB_FRAGS + 2);
+
+ spin_unlock_irqrestore(&adapter->tx_queue_lock, irq_flags);
+ return NETDEV_TX_OK;
+}
+
+/**
+ * e1000_tx_timeout - Respond to a Tx Hang
+ * @netdev: network interface device structure
+ **/
+static void e1000_tx_timeout(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ /* Do the reset outside of interrupt context */
+ adapter->tx_timeout_count++;
+ schedule_work(&adapter->reset_task);
+}
+
+static void e1000_reset_task(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ e1000e_reinit_locked(adapter);
+}
+
+/**
+ * e1000_get_stats - Get System Network Statistics
+ * @netdev: network interface device structure
+ *
+ * Returns the address of the device statistics structure.
+ * The statistics are actually updated from the timer callback.
+ **/
+static struct net_device_stats *e1000_get_stats(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ /* only return the current stats */
+ return &adapter->net_stats;
+}
+
+/**
+ * e1000_change_mtu - Change the Maximum Transfer Unit
+ * @netdev: network interface device structure
+ * @new_mtu: new value for maximum frame size
+ *
+ * Returns 0 on success, negative on failure
+ **/
+static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN;
+
+ if ((new_mtu < ETH_ZLEN + ETH_FCS_LEN + VLAN_HLEN) ||
+ (max_frame > MAX_JUMBO_FRAME_SIZE)) {
+ e_err("Invalid MTU setting\n");
+ return -EINVAL;
+ }
+
+ /* Jumbo frame size limits */
+ if (max_frame > ETH_FRAME_LEN + ETH_FCS_LEN) {
+ if (!(adapter->flags & FLAG_HAS_JUMBO_FRAMES)) {
+ e_err("Jumbo Frames not supported.\n");
+ return -EINVAL;
+ }
+ if (adapter->hw.phy.type == e1000_phy_ife) {
+ e_err("Jumbo Frames not supported.\n");
+ return -EINVAL;
+ }
+ }
+
+#define MAX_STD_JUMBO_FRAME_SIZE 9234
+ if (max_frame > MAX_STD_JUMBO_FRAME_SIZE) {
+ e_err("MTU > 9216 not supported.\n");
+ return -EINVAL;
+ }
+
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
+ msleep(1);
+ /* e1000e_down has a dependency on max_frame_size */
+ adapter->max_frame_size = max_frame;
+ if (netif_running(netdev))
+ e1000e_down(adapter);
+
+ /*
+ * NOTE: netdev_alloc_skb reserves 16 bytes, and typically NET_IP_ALIGN
+ * means we reserve 2 more, this pushes us to allocate from the next
+ * larger slab size.
+ * i.e. RXBUFFER_2048 --> size-4096 slab
+ * However with the new *_jumbo_rx* routines, jumbo receives will use
+ * fragmented skbs
+ */
+
+ if (max_frame <= 256)
+ adapter->rx_buffer_len = 256;
+ else if (max_frame <= 512)
+ adapter->rx_buffer_len = 512;
+ else if (max_frame <= 1024)
+ adapter->rx_buffer_len = 1024;
+ else if (max_frame <= 2048)
+ adapter->rx_buffer_len = 2048;
+ else
+ adapter->rx_buffer_len = 4096;
+
+ /* adjust allocation if LPE protects us, and we aren't using SBP */
+ if ((max_frame == ETH_FRAME_LEN + ETH_FCS_LEN) ||
+ (max_frame == ETH_FRAME_LEN + VLAN_HLEN + ETH_FCS_LEN))
+ adapter->rx_buffer_len = ETH_FRAME_LEN + VLAN_HLEN
+ + ETH_FCS_LEN;
+
+ e_info("changing MTU from %d to %d\n", netdev->mtu, new_mtu);
+ netdev->mtu = new_mtu;
+
+ if (netif_running(netdev))
+ e1000e_up(adapter);
+ else
+ e1000e_reset(adapter);
+
+ clear_bit(__E1000_RESETTING, &adapter->state);
+
+ return 0;
+}
+
+static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
+ int cmd)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct mii_ioctl_data *data = if_mii(ifr);
+
+ if (adapter->hw.phy.media_type != e1000_media_type_copper)
+ return -EOPNOTSUPP;
+
+ switch (cmd) {
+ case SIOCGMIIPHY:
+ data->phy_id = adapter->hw.phy.addr;
+ break;
+ case SIOCGMIIREG:
+ if (!capable(CAP_NET_ADMIN))
+ return -EPERM;
+ switch (data->reg_num & 0x1F) {
+ case MII_BMCR:
+ data->val_out = adapter->phy_regs.bmcr;
+ break;
+ case MII_BMSR:
+ data->val_out = adapter->phy_regs.bmsr;
+ break;
+ case MII_PHYSID1:
+ data->val_out = (adapter->hw.phy.id >> 16);
+ break;
+ case MII_PHYSID2:
+ data->val_out = (adapter->hw.phy.id & 0xFFFF);
+ break;
+ case MII_ADVERTISE:
+ data->val_out = adapter->phy_regs.advertise;
+ break;
+ case MII_LPA:
+ data->val_out = adapter->phy_regs.lpa;
+ break;
+ case MII_EXPANSION:
+ data->val_out = adapter->phy_regs.expansion;
+ break;
+ case MII_CTRL1000:
+ data->val_out = adapter->phy_regs.ctrl1000;
+ break;
+ case MII_STAT1000:
+ data->val_out = adapter->phy_regs.stat1000;
+ break;
+ case MII_ESTATUS:
+ data->val_out = adapter->phy_regs.estatus;
+ break;
+ default:
+ return -EIO;
+ }
+ break;
+ case SIOCSMIIREG:
+ default:
+ return -EOPNOTSUPP;
+ }
+ return 0;
+}
+
+static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
+{
+ switch (cmd) {
+ case SIOCGMIIPHY:
+ case SIOCGMIIREG:
+ case SIOCSMIIREG:
+ return e1000_mii_ioctl(netdev, ifr, cmd);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static int e1000_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 ctrl, ctrl_ext, rctl, status;
+ u32 wufc = adapter->wol;
+ int retval = 0;
+
+ netif_device_detach(netdev);
+
+ if (netif_running(netdev)) {
+ WARN_ON(test_bit(__E1000_RESETTING, &adapter->state));
+ e1000e_down(adapter);
+ e1000_free_irq(adapter);
+ }
+ e1000e_reset_interrupt_capability(adapter);
+
+ retval = pci_save_state(pdev);
+ if (retval)
+ return retval;
+
+ status = er32(STATUS);
+ if (status & E1000_STATUS_LU)
+ wufc &= ~E1000_WUFC_LNKC;
+
+ if (wufc) {
+ e1000_setup_rctl(adapter);
+ e1000_set_multi(netdev);
+
+ /* turn on all-multi mode if wake on multicast is enabled */
+ if (wufc & E1000_WUFC_MC) {
+ rctl = er32(RCTL);
+ rctl |= E1000_RCTL_MPE;
+ ew32(RCTL, rctl);
+ }
+
+ ctrl = er32(CTRL);
+ /* advertise wake from D3Cold */
+ #define E1000_CTRL_ADVD3WUC 0x00100000
+ /* phy power management enable */
+ #define E1000_CTRL_EN_PHY_PWR_MGMT 0x00200000
+ ctrl |= E1000_CTRL_ADVD3WUC |
+ E1000_CTRL_EN_PHY_PWR_MGMT;
+ ew32(CTRL, ctrl);
+
+ if (adapter->hw.phy.media_type == e1000_media_type_fiber ||
+ adapter->hw.phy.media_type ==
+ e1000_media_type_internal_serdes) {
+ /* keep the laser running in D3 */
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_SDP7_DATA;
+ ew32(CTRL_EXT, ctrl_ext);
+ }
+
+ if (adapter->flags & FLAG_IS_ICH)
+ e1000e_disable_gig_wol_ich8lan(&adapter->hw);
+
+ /* Allow time for pending master requests to run */
+ e1000e_disable_pcie_master(&adapter->hw);
+
+ ew32(WUC, E1000_WUC_PME_EN);
+ ew32(WUFC, wufc);
+ pci_enable_wake(pdev, PCI_D3hot, 1);
+ pci_enable_wake(pdev, PCI_D3cold, 1);
+ } else {
+ ew32(WUC, 0);
+ ew32(WUFC, 0);
+ pci_enable_wake(pdev, PCI_D3hot, 0);
+ pci_enable_wake(pdev, PCI_D3cold, 0);
+ }
+
+ /* make sure adapter isn't asleep if manageability is enabled */
+ if (adapter->flags & FLAG_MNG_PT_ENABLED) {
+ pci_enable_wake(pdev, PCI_D3hot, 1);
+ pci_enable_wake(pdev, PCI_D3cold, 1);
+ }
+
+ if (adapter->hw.phy.type == e1000_phy_igp_3)
+ e1000e_igp3_phy_powerdown_workaround_ich8lan(&adapter->hw);
+
+ /*
+ * Release control of h/w to f/w. If f/w is AMT enabled, this
+ * would have already happened in close and is redundant.
+ */
+ e1000_release_hw_control(adapter);
+
+ pci_disable_device(pdev);
+
+ pci_set_power_state(pdev, pci_choose_state(pdev, state));
+
+ return 0;
+}
+
+static void e1000e_disable_l1aspm(struct pci_dev *pdev)
+{
+ int pos;
+ u16 val;
+
+ /*
+ * 82573 workaround - disable L1 ASPM on mobile chipsets
+ *
+ * L1 ASPM on various mobile (ich7) chipsets do not behave properly
+ * resulting in lost data or garbage information on the pci-e link
+ * level. This could result in (false) bad EEPROM checksum errors,
+ * long ping times (up to 2s) or even a system freeze/hang.
+ *
+ * Unfortunately this feature saves about 1W power consumption when
+ * active.
+ */
+ pos = pci_find_capability(pdev, PCI_CAP_ID_EXP);
+ pci_read_config_word(pdev, pos + PCI_EXP_LNKCTL, &val);
+ if (val & 0x2) {
+ dev_warn(&pdev->dev, "Disabling L1 ASPM\n");
+ val &= ~0x2;
+ pci_write_config_word(pdev, pos + PCI_EXP_LNKCTL, val);
+ }
+}
+
+#ifdef CONFIG_PM
+static int e1000_resume(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+ u32 err;
+
+ pci_set_power_state(pdev, PCI_D0);
+ pci_restore_state(pdev);
+ e1000e_disable_l1aspm(pdev);
+ err = pci_enable_device(pdev);
+ if (err) {
+ dev_err(&pdev->dev,
+ "Cannot enable PCI device from suspend\n");
+ return err;
+ }
+
+ pci_set_master(pdev);
+ pci_restore_state(pdev);
+
+ pci_enable_wake(pdev, PCI_D3hot, 0);
+ pci_enable_wake(pdev, PCI_D3cold, 0);
+
+ e1000e_set_interrupt_capability(adapter);
+ if (netif_running(netdev)) {
+ err = e1000_request_irq(adapter);
+ if (err)
+ return err;
+ }
+
+ e1000e_power_up_phy(adapter);
+ e1000e_reset(adapter);
+ ew32(WUS, ~0);
+
+ e1000_init_manageability(adapter);
+
+ if (netif_running(netdev))
+ e1000e_up(adapter);
+
+ netif_device_attach(netdev);
+
+ /*
+ * If the controller has AMT, do not set DRV_LOAD until the interface
+ * is up. For all other cases, let the f/w know that the h/w is now
+ * under the control of the driver.
+ */
+ if (!(adapter->flags & FLAG_HAS_AMT))
+ e1000_get_hw_control(adapter);
+
+ return 0;
+}
+#endif
+
+static void e1000_shutdown(struct pci_dev *pdev)
+{
+ e1000_suspend(pdev, PMSG_SUSPEND);
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+/*
+ * Polling 'interrupt' - used by things like netconsole to send skbs
+ * without having to re-enable interrupts. It's not called while
+ * the interrupt routine is executing.
+ */
+static void e1000_netpoll(struct net_device *netdev)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ disable_irq(adapter->pdev->irq);
+ e1000_intr(adapter->pdev->irq, netdev, NULL);
+
+ enable_irq(adapter->pdev->irq);
+}
+#endif
+
+/**
+ * e1000_io_error_detected - called when PCI error is detected
+ * @pdev: Pointer to PCI device
+ * @state: The current pci connection state
+ *
+ * This function is called after a PCI bus error affecting
+ * this device has been detected.
+ */
+static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev,
+ pci_channel_state_t state)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ netif_device_detach(netdev);
+
+ if (netif_running(netdev))
+ e1000e_down(adapter);
+ pci_disable_device(pdev);
+
+ /* Request a slot slot reset. */
+ return PCI_ERS_RESULT_NEED_RESET;
+}
+
+/**
+ * e1000_io_slot_reset - called after the pci bus has been reset.
+ * @pdev: Pointer to PCI device
+ *
+ * Restart the card from scratch, as if from a cold-boot. Implementation
+ * resembles the first-half of the e1000_resume routine.
+ */
+static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+ struct e1000_hw *hw = &adapter->hw;
+
+ e1000e_disable_l1aspm(pdev);
+ if (pci_enable_device(pdev)) {
+ dev_err(&pdev->dev,
+ "Cannot re-enable PCI device after reset.\n");
+ return PCI_ERS_RESULT_DISCONNECT;
+ }
+ pci_set_master(pdev);
+ pci_restore_state(pdev);
+
+ pci_enable_wake(pdev, PCI_D3hot, 0);
+ pci_enable_wake(pdev, PCI_D3cold, 0);
+
+ e1000e_reset(adapter);
+ ew32(WUS, ~0);
+
+ return PCI_ERS_RESULT_RECOVERED;
+}
+
+/**
+ * e1000_io_resume - called when traffic can start flowing again.
+ * @pdev: Pointer to PCI device
+ *
+ * This callback is called when the error recovery driver tells us that
+ * its OK to resume normal operation. Implementation resembles the
+ * second-half of the e1000_resume routine.
+ */
+static void e1000_io_resume(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ e1000_init_manageability(adapter);
+
+ if (netif_running(netdev)) {
+ if (e1000e_up(adapter)) {
+ dev_err(&pdev->dev,
+ "can't bring device back up after reset\n");
+ return;
+ }
+ }
+
+ netif_device_attach(netdev);
+
+ /*
+ * If the controller has AMT, do not set DRV_LOAD until the interface
+ * is up. For all other cases, let the f/w know that the h/w is now
+ * under the control of the driver.
+ */
+ if (!(adapter->flags & FLAG_HAS_AMT))
+ e1000_get_hw_control(adapter);
+
+}
+
+static void e1000_print_device_info(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ struct net_device *netdev = adapter->netdev;
+ u32 pba_num;
+
+ /* print bus type/speed/width info */
+ e_info("(PCI Express:2.5GB/s:%s) %02x:%02x:%02x:%02x:%02x:%02x\n",
+ /* bus width */
+ ((hw->bus.width == e1000_bus_width_pcie_x4) ? "Width x4" :
+ "Width x1"),
+ /* MAC address */
+ netdev->dev_addr[0], netdev->dev_addr[1],
+ netdev->dev_addr[2], netdev->dev_addr[3],
+ netdev->dev_addr[4], netdev->dev_addr[5]);
+ e_info("Intel(R) PRO/%s Network Connection\n",
+ (hw->phy.type == e1000_phy_ife) ? "10/100" : "1000");
+ e1000e_read_pba_num(hw, &pba_num);
+ e_info("MAC: %d, PHY: %d, PBA No: %06x-%03x\n",
+ hw->mac.type, hw->phy.type, (pba_num >> 8), (pba_num & 0xff));
+}
+
+static void e1000_eeprom_checks(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ int ret_val;
+ u16 buf = 0;
+
+ if (hw->mac.type != e1000_82573)
+ return;
+
+ ret_val = e1000_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &buf);
+ if (!(le16_to_cpu(buf) & (1 << 0))) {
+ /* Deep Smart Power Down (DSPD) */
+ e_warn("Warning: detected DSPD enabled in EEPROM\n");
+ }
+
+ ret_val = e1000_read_nvm(hw, NVM_INIT_3GIO_3, 1, &buf);
+ if (le16_to_cpu(buf) & (3 << 2)) {
+ /* ASPM enable */
+ e_warn("Warning: detected ASPM enabled in EEPROM\n");
+ }
+}
+
+/**
+ * e1000_probe - Device Initialization Routine
+ * @pdev: PCI device information struct
+ * @ent: entry in e1000_pci_tbl
+ *
+ * Returns 0 on success, negative on failure
+ *
+ * e1000_probe initializes an adapter identified by a pci_dev structure.
+ * The OS initialization, configuring of the adapter private structure,
+ * and a hardware reset occur.
+ **/
+static int __devinit e1000_probe(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ struct net_device *netdev;
+ struct e1000_adapter *adapter;
+ struct e1000_hw *hw;
+ const struct e1000_info *ei = e1000_info_tbl[ent->driver_data];
+ resource_size_t mmio_start, mmio_len;
+ resource_size_t flash_start, flash_len;
+
+ static int cards_found;
+ int i, err, pci_using_dac;
+ u16 eeprom_data = 0;
+ u16 eeprom_apme_mask = E1000_EEPROM_APME;
+
+ e1000e_disable_l1aspm(pdev);
+ err = pci_enable_device(pdev);
+ if (err)
+ return err;
+
+ pci_using_dac = 0;
+ err = pci_set_dma_mask(pdev, DMA_64BIT_MASK);
+ if (!err) {
+ err = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
+ if (!err)
+ pci_using_dac = 1;
+ } else {
+ err = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
+ if (err) {
+ err = pci_set_consistent_dma_mask(pdev,
+ DMA_32BIT_MASK);
+ if (err) {
+ dev_err(&pdev->dev, "No usable DMA "
+ "configuration, aborting\n");
+ goto err_dma;
+ }
+ }
+ }
+
+ err = pci_request_regions(pdev, e1000e_driver_name);
+ if (err)
+ goto err_pci_reg;
+
+ pci_set_master(pdev);
+ pci_save_state(pdev);
+
+ err = -ENOMEM;
+ netdev = alloc_etherdev(sizeof(struct e1000_adapter));
+ if (!netdev)
+ goto err_alloc_etherdev;
+
+ SET_MODULE_OWNER(netdev);
+ SET_NETDEV_DEV(netdev, &pdev->dev);
+
+ pci_set_drvdata(pdev, netdev);
+ adapter = netdev_priv(netdev);
+ hw = &adapter->hw;
+ adapter->netdev = netdev;
+ adapter->pdev = pdev;
+ adapter->ei = ei;
+ adapter->pba = ei->pba;
+ adapter->flags = ei->flags;
+ adapter->hw.adapter = adapter;
+ adapter->hw.mac.type = ei->mac;
+ adapter->msg_enable = (1 << NETIF_MSG_DRV | NETIF_MSG_PROBE) - 1;
+
+ mmio_start = pci_resource_start(pdev, 0);
+ mmio_len = pci_resource_len(pdev, 0);
+
+ err = -EIO;
+ adapter->hw.hw_addr = ioremap(mmio_start, mmio_len);
+ if (!adapter->hw.hw_addr)
+ goto err_ioremap;
+
+ if ((adapter->flags & FLAG_HAS_FLASH) &&
+ (pci_resource_flags(pdev, 1) & IORESOURCE_MEM)) {
+ flash_start = pci_resource_start(pdev, 1);
+ flash_len = pci_resource_len(pdev, 1);
+ adapter->hw.flash_address = ioremap(flash_start, flash_len);
+ if (!adapter->hw.flash_address)
+ goto err_flashmap;
+ }
+
+ /* construct the net_device struct */
+ netdev->open = &e1000_open;
+ netdev->stop = &e1000_close;
+ netdev->hard_start_xmit = &e1000_xmit_frame;
+ netdev->get_stats = &e1000_get_stats;
+ netdev->set_multicast_list = &e1000_set_multi;
+ netdev->set_mac_address = &e1000_set_mac;
+ netdev->change_mtu = &e1000_change_mtu;
+ netdev->do_ioctl = &e1000_ioctl;
+ e1000e_set_ethtool_ops(netdev);
+ netdev->tx_timeout = &e1000_tx_timeout;
+ netdev->watchdog_timeo = 5 * HZ;
+ netdev->poll = &e1000_clean;
+ netdev->weight = 64;
+ netdev->vlan_rx_register = e1000_vlan_rx_register;
+ netdev->vlan_rx_add_vid = e1000_vlan_rx_add_vid;
+ netdev->vlan_rx_kill_vid = e1000_vlan_rx_kill_vid;
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ netdev->poll_controller = e1000_netpoll;
+#endif
+ strncpy(netdev->name, pci_name(pdev), sizeof(netdev->name) - 1);
+
+ netdev->mem_start = mmio_start;
+ netdev->mem_end = mmio_start + mmio_len;
+
+ adapter->bd_number = cards_found++;
+
+ e1000e_check_options(adapter);
+
+ /* setup adapter struct */
+ err = e1000_sw_init(adapter);
+ if (err)
+ goto err_sw_init;
+
+ err = -EIO;
+
+ memcpy(&hw->mac.ops, ei->mac_ops, sizeof(hw->mac.ops));
+ memcpy(&hw->nvm.ops, ei->nvm_ops, sizeof(hw->nvm.ops));
+ memcpy(&hw->phy.ops, ei->phy_ops, sizeof(hw->phy.ops));
+
+ err = ei->get_variants(adapter);
+ if (err)
+ goto err_hw_init;
+
+ if ((adapter->flags & FLAG_IS_ICH) &&
+ (adapter->flags & FLAG_READ_ONLY_NVM))
+ e1000e_write_protect_nvm_ich8lan(&adapter->hw);
+
+ hw->mac.ops.get_bus_info(&adapter->hw);
+
+ adapter->hw.phy.autoneg_wait_to_complete = 0;
+
+ /* Copper options */
+ if (adapter->hw.phy.media_type == e1000_media_type_copper) {
+ adapter->hw.phy.mdix = AUTO_ALL_MODES;
+ adapter->hw.phy.disable_polarity_correction = 0;
+ adapter->hw.phy.ms_type = e1000_ms_hw_default;
+ }
+
+ if (e1000_check_reset_block(&adapter->hw))
+ e_info("PHY reset is blocked due to SOL/IDER session.\n");
+
+ netdev->features = NETIF_F_SG |
+ NETIF_F_HW_CSUM |
+ NETIF_F_HW_VLAN_TX |
+ NETIF_F_HW_VLAN_RX;
+
+ if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER)
+ netdev->features |= NETIF_F_HW_VLAN_FILTER;
+
+ netdev->features |= NETIF_F_TSO;
+ netdev->features |= NETIF_F_TSO6;
+
+ if (pci_using_dac)
+ netdev->features |= NETIF_F_HIGHDMA;
+
+ /*
+ * We should not be using LLTX anymore, but we are still Tx faster with
+ * it.
+ */
+ netdev->features |= NETIF_F_LLTX;
+
+ if (e1000e_enable_mng_pass_thru(&adapter->hw))
+ adapter->flags |= FLAG_MNG_PT_ENABLED;
+
+ /*
+ * before reading the NVM, reset the controller to
+ * put the device in a known good starting state
+ */
+ adapter->hw.mac.ops.reset_hw(&adapter->hw);
+
+ /*
+ * systems with ASPM and others may see the checksum fail on the first
+ * attempt. Let's give it a few tries
+ */
+ for (i = 0;; i++) {
+ if (e1000_validate_nvm_checksum(&adapter->hw) >= 0)
+ break;
+ if (i == 2) {
+ e_err("The NVM Checksum Is Not Valid\n");
+ err = -EIO;
+ goto err_eeprom;
+ }
+ }
+
+ e1000_eeprom_checks(adapter);
+
+ /* copy the MAC address out of the NVM */
+ if (e1000e_read_mac_addr(&adapter->hw))
+ e_err("NVM Read Error while reading MAC address\n");
+
+ memcpy(netdev->dev_addr, adapter->hw.mac.addr, netdev->addr_len);
+ memcpy(netdev->perm_addr, adapter->hw.mac.addr, netdev->addr_len);
+
+ if (!is_valid_ether_addr(netdev->perm_addr)) {
+ e_err("Invalid MAC Address: %02x:%02x:%02x:%02x:%02x:%02x\n",
+ netdev->perm_addr[0], netdev->perm_addr[1],
+ netdev->perm_addr[2], netdev->perm_addr[3],
+ netdev->perm_addr[4], netdev->perm_addr[5]);
+ err = -EIO;
+ goto err_eeprom;
+ }
+
+ init_timer(&adapter->watchdog_timer);
+ adapter->watchdog_timer.function = &e1000_watchdog;
+ adapter->watchdog_timer.data = (unsigned long) adapter;
+
+ init_timer(&adapter->phy_info_timer);
+ adapter->phy_info_timer.function = &e1000_update_phy_info;
+ adapter->phy_info_timer.data = (unsigned long) adapter;
+
+ INIT_WORK(&adapter->reset_task,
+ (void (*)(void *))e1000_reset_task, netdev);
+ INIT_WORK(&adapter->watchdog_task,
+ (void (*)(void *))e1000_watchdog_task, netdev);
+
+ /* Initialize link parameters. User can change them with ethtool */
+ adapter->hw.mac.autoneg = 1;
+ adapter->fc_autoneg = 1;
+ adapter->hw.fc.original_type = e1000_fc_default;
+ adapter->hw.fc.type = e1000_fc_default;
+ adapter->hw.phy.autoneg_advertised = 0x2f;
+
+ /* ring size defaults */
+ adapter->rx_ring->count = 256;
+ adapter->tx_ring->count = 256;
+
+ /*
+ * Initial Wake on LAN setting - If APM wake is enabled in
+ * the EEPROM, enable the ACPI Magic Packet filter
+ */
+ if (adapter->flags & FLAG_APME_IN_WUC) {
+ /* APME bit in EEPROM is mapped to WUC.APME */
+ eeprom_data = er32(WUC);
+ eeprom_apme_mask = E1000_WUC_APME;
+ } else if (adapter->flags & FLAG_APME_IN_CTRL3) {
+ if (adapter->flags & FLAG_APME_CHECK_PORT_B &&
+ (adapter->hw.bus.func == 1))
+ e1000_read_nvm(&adapter->hw,
+ NVM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
+ else
+ e1000_read_nvm(&adapter->hw,
+ NVM_INIT_CONTROL3_PORT_A, 1, &eeprom_data);
+ }
+
+ /* fetch WoL from EEPROM */
+ if (eeprom_data & eeprom_apme_mask)
+ adapter->eeprom_wol |= E1000_WUFC_MAG;
+
+ /*
+ * now that we have the eeprom settings, apply the special cases
+ * where the eeprom may be wrong or the board simply won't support
+ * wake on lan on a particular port
+ */
+ if (!(adapter->flags & FLAG_HAS_WOL))
+ adapter->eeprom_wol = 0;
+
+ /* initialize the wol settings based on the eeprom settings */
+ adapter->wol = adapter->eeprom_wol;
+
+ /* reset the hardware with the new settings */
+ e1000e_reset(adapter);
+
+ /*
+ * If the controller has AMT, do not set DRV_LOAD until the interface
+ * is up. For all other cases, let the f/w know that the h/w is now
+ * under the control of the driver.
+ */
+ if (!(adapter->flags & FLAG_HAS_AMT))
+ e1000_get_hw_control(adapter);
+
+ /* tell the stack to leave us alone until e1000_open() is called */
+ netif_carrier_off(netdev);
+ netif_stop_queue(netdev);
+
+ strcpy(netdev->name, "eth%d");
+ err = register_netdev(netdev);
+ if (err)
+ goto err_register;
+
+ e1000_print_device_info(adapter);
+
+ return 0;
+
+err_register:
+ if (!(adapter->flags & FLAG_HAS_AMT))
+ e1000_release_hw_control(adapter);
+err_eeprom:
+ if (!e1000_check_reset_block(&adapter->hw))
+ e1000_phy_hw_reset(&adapter->hw);
+err_hw_init:
+
+ kfree(adapter->tx_ring);
+ kfree(adapter->rx_ring);
+err_sw_init:
+ if (adapter->hw.flash_address)
+ iounmap(adapter->hw.flash_address);
+err_flashmap:
+ iounmap(adapter->hw.hw_addr);
+err_ioremap:
+ free_netdev(netdev);
+err_alloc_etherdev:
+ pci_release_regions(pdev);
+err_pci_reg:
+err_dma:
+ pci_disable_device(pdev);
+ return err;
+}
+
+/**
+ * e1000_remove - Device Removal Routine
+ * @pdev: PCI device information struct
+ *
+ * e1000_remove is called by the PCI subsystem to alert the driver
+ * that it should release a PCI device. The could be caused by a
+ * Hot-Plug event, or because the driver is going to be removed from
+ * memory.
+ **/
+static void __devexit e1000_remove(struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ /*
+ * flush_scheduled work may reschedule our watchdog task, so
+ * explicitly disable watchdog tasks from being rescheduled
+ */
+ set_bit(__E1000_DOWN, &adapter->state);
+ del_timer_sync(&adapter->watchdog_timer);
+ del_timer_sync(&adapter->phy_info_timer);
+
+ flush_scheduled_work();
+
+ /*
+ * Release control of h/w to f/w. If f/w is AMT enabled, this
+ * would have already happened in close and is redundant.
+ */
+ e1000_release_hw_control(adapter);
+
+ unregister_netdev(netdev);
+
+ if (!e1000_check_reset_block(&adapter->hw))
+ e1000_phy_hw_reset(&adapter->hw);
+
+ e1000e_reset_interrupt_capability(adapter);
+ kfree(adapter->tx_ring);
+ kfree(adapter->rx_ring);
+
+ iounmap(adapter->hw.hw_addr);
+ if (adapter->hw.flash_address)
+ iounmap(adapter->hw.flash_address);
+ pci_release_regions(pdev);
+
+ free_netdev(netdev);
+
+ pci_disable_device(pdev);
+}
+
+/* PCI Error Recovery (ERS) */
+static struct pci_error_handlers e1000_err_handler = {
+ .error_detected = e1000_io_error_detected,
+ .slot_reset = e1000_io_slot_reset,
+ .resume = e1000_io_resume,
+};
+
+static struct pci_device_id e1000_pci_tbl[] = {
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_COPPER), board_82571 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_FIBER), board_82571 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_COPPER), board_82571 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_COPPER_LP), board_82571 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_FIBER), board_82571 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES), board_82571 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES_DUAL), board_82571 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES_QUAD), board_82571 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571PT_QUAD_COPPER), board_82571 },
+
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI), board_82572 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_COPPER), board_82572 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_FIBER), board_82572 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_SERDES), board_82572 },
+
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573E), board_82573 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573E_IAMT), board_82573 },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573L), board_82573 },
+
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_82574L), board_82574 },
+
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_COPPER_DPT),
+ board_80003es2lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_COPPER_SPT),
+ board_80003es2lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_SERDES_DPT),
+ board_80003es2lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_SERDES_SPT),
+ board_80003es2lan },
+
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE), board_ich8lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE_G), board_ich8lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE_GT), board_ich8lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_AMT), board_ich8lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_C), board_ich8lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_M), board_ich8lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_M_AMT), board_ich8lan },
+
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE_G), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE_GT), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_AMT), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_C), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_BM), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M_AMT), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M_V), board_ich9lan },
+
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_LM), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_LF), board_ich9lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_V), board_ich9lan },
+
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LM), board_ich10lan },
+ { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LF), board_ich10lan },
+
+ { } /* terminate list */
+};
+MODULE_DEVICE_TABLE(pci, e1000_pci_tbl);
+
+/* PCI Device API Driver */
+static struct pci_driver e1000_driver = {
+ .name = e1000e_driver_name,
+ .id_table = e1000_pci_tbl,
+ .probe = e1000_probe,
+ .remove = __devexit_p(e1000_remove),
+#ifdef CONFIG_PM
+ /* Power Management Hooks */
+ .suspend = e1000_suspend,
+ .resume = e1000_resume,
+#endif
+ .shutdown = e1000_shutdown,
+ .err_handler = &e1000_err_handler
+};
+
+/**
+ * e1000_init_module - Driver Registration Routine
+ *
+ * e1000_init_module is the first routine called when the driver is
+ * loaded. All it does is register with the PCI subsystem.
+ **/
+static int __init e1000_init_module(void)
+{
+ int ret;
+ printk(KERN_INFO "%s: Intel(R) PRO/1000 Network Driver - %s\n",
+ e1000e_driver_name, e1000e_driver_version);
+ printk(KERN_INFO "%s: Copyright (c) 1999-2008 Intel Corporation.\n",
+ e1000e_driver_name);
+ ret = pci_register_driver(&e1000_driver);
+#if 0 /* not in RHEL */
+ pm_qos_add_requirement(PM_QOS_CPU_DMA_LATENCY, e1000e_driver_name,
+ PM_QOS_DEFAULT_VALUE);
+#endif
+ return ret;
+}
+module_init(e1000_init_module);
+
+/**
+ * e1000_exit_module - Driver Exit Cleanup Routine
+ *
+ * e1000_exit_module is called just before the driver is removed
+ * from memory.
+ **/
+static void __exit e1000_exit_module(void)
+{
+ pci_unregister_driver(&e1000_driver);
+#if 0 /* not in RHEL */
+ pm_qos_remove_requirement(PM_QOS_CPU_DMA_LATENCY, e1000e_driver_name);
+#endif
+}
+module_exit(e1000_exit_module);
+
+
+MODULE_AUTHOR("Intel Corporation, <linux.nics@intel.com>");
+MODULE_DESCRIPTION("Intel(R) PRO/1000 Network Driver");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+
+/* e1000_main.c */
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2008 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#include <linux/netdevice.h>
+#include <linux/pci.h>
+
+#include "e1000.h"
+
+/*
+ * This is the only thing that needs to be changed to adjust the
+ * maximum number of ports that the driver can manage.
+ */
+
+#define E1000_MAX_NIC 32
+
+#define OPTION_UNSET -1
+#define OPTION_DISABLED 0
+#define OPTION_ENABLED 1
+
+#define COPYBREAK_DEFAULT 256
+unsigned int copybreak = COPYBREAK_DEFAULT;
+module_param(copybreak, uint, 0644);
+MODULE_PARM_DESC(copybreak,
+ "Maximum size of packet that is copied to a new buffer on receive");
+
+/*
+ * All parameters are treated the same, as an integer array of values.
+ * This macro just reduces the need to repeat the same declaration code
+ * over and over (plus this helps to avoid typo bugs).
+ */
+
+#define E1000_PARAM_INIT { [0 ... E1000_MAX_NIC] = OPTION_UNSET }
+#define E1000_PARAM(X, desc) \
+ static int __devinitdata X[E1000_MAX_NIC+1] \
+ = E1000_PARAM_INIT; \
+ static unsigned int num_##X; \
+ module_param_array_named(X, X, int, &num_##X, 0); \
+ MODULE_PARM_DESC(X, desc);
+
+
+/*
+ * Transmit Interrupt Delay in units of 1.024 microseconds
+ * Tx interrupt delay needs to typically be set to something non zero
+ *
+ * Valid Range: 0-65535
+ */
+E1000_PARAM(TxIntDelay, "Transmit Interrupt Delay");
+#define DEFAULT_TIDV 8
+#define MAX_TXDELAY 0xFFFF
+#define MIN_TXDELAY 0
+
+/*
+ * Transmit Absolute Interrupt Delay in units of 1.024 microseconds
+ *
+ * Valid Range: 0-65535
+ */
+E1000_PARAM(TxAbsIntDelay, "Transmit Absolute Interrupt Delay");
+#define DEFAULT_TADV 32
+#define MAX_TXABSDELAY 0xFFFF
+#define MIN_TXABSDELAY 0
+
+/*
+ * Receive Interrupt Delay in units of 1.024 microseconds
+ * hardware will likely hang if you set this to anything but zero.
+ *
+ * Valid Range: 0-65535
+ */
+E1000_PARAM(RxIntDelay, "Receive Interrupt Delay");
+#define DEFAULT_RDTR 0
+#define MAX_RXDELAY 0xFFFF
+#define MIN_RXDELAY 0
+
+/*
+ * Receive Absolute Interrupt Delay in units of 1.024 microseconds
+ *
+ * Valid Range: 0-65535
+ */
+E1000_PARAM(RxAbsIntDelay, "Receive Absolute Interrupt Delay");
+#define DEFAULT_RADV 8
+#define MAX_RXABSDELAY 0xFFFF
+#define MIN_RXABSDELAY 0
+
+/*
+ * Interrupt Throttle Rate (interrupts/sec)
+ *
+ * Valid Range: 100-100000 (0=off, 1=dynamic, 3=dynamic conservative)
+ */
+E1000_PARAM(InterruptThrottleRate, "Interrupt Throttling Rate");
+#define DEFAULT_ITR 3
+#define MAX_ITR 100000
+#define MIN_ITR 100
+/* IntMode (Interrupt Mode)
+ *
+ * Valid Range: 0 - 2
+ *
+ * Default Value: 2 (MSI-X)
+ */
+E1000_PARAM(IntMode, "Interrupt Mode");
+#define MAX_INTMODE 2
+#define MIN_INTMODE 0
+
+/*
+ * Enable Smart Power Down of the PHY
+ *
+ * Valid Range: 0, 1
+ *
+ * Default Value: 0 (disabled)
+ */
+E1000_PARAM(SmartPowerDownEnable, "Enable PHY smart power down");
+
+/*
+ * Enable Kumeran Lock Loss workaround
+ *
+ * Valid Range: 0, 1
+ *
+ * Default Value: 1 (enabled)
+ */
+E1000_PARAM(KumeranLockLoss, "Enable Kumeran lock loss workaround");
+
+/*
+ * Write Protect NVM
+ *
+ * Valid Range: 0, 1
+ *
+ * Default Value: 1 (enabled)
+ */
+E1000_PARAM(WriteProtectNVM, "Write-protect NVM [WARNING: disabling this can lead to corrupted NVM]");
+
+struct e1000_option {
+ enum { enable_option, range_option, list_option } type;
+ const char *name;
+ const char *err;
+ int def;
+ union {
+ struct { /* range_option info */
+ int min;
+ int max;
+ } r;
+ struct { /* list_option info */
+ int nr;
+ struct e1000_opt_list { int i; char *str; } *p;
+ } l;
+ } arg;
+};
+
+static int __devinit e1000_validate_option(unsigned int *value,
+ const struct e1000_option *opt,
+ struct e1000_adapter *adapter)
+{
+ if (*value == OPTION_UNSET) {
+ *value = opt->def;
+ return 0;
+ }
+
+ switch (opt->type) {
+ case enable_option:
+ switch (*value) {
+ case OPTION_ENABLED:
+ e_info("%s Enabled\n", opt->name);
+ return 0;
+ case OPTION_DISABLED:
+ e_info("%s Disabled\n", opt->name);
+ return 0;
+ }
+ break;
+ case range_option:
+ if (*value >= opt->arg.r.min && *value <= opt->arg.r.max) {
+ e_info("%s set to %i\n", opt->name, *value);
+ return 0;
+ }
+ break;
+ case list_option: {
+ int i;
+ struct e1000_opt_list *ent;
+
+ for (i = 0; i < opt->arg.l.nr; i++) {
+ ent = &opt->arg.l.p[i];
+ if (*value == ent->i) {
+ if (ent->str[0] != '\0')
+ e_info("%s\n", ent->str);
+ return 0;
+ }
+ }
+ }
+ break;
+ default:
+ BUG();
+ }
+
+ e_info("Invalid %s value specified (%i) %s\n", opt->name, *value,
+ opt->err);
+ *value = opt->def;
+ return -1;
+}
+
+/**
+ * e1000e_check_options - Range Checking for Command Line Parameters
+ * @adapter: board private structure
+ *
+ * This routine checks all command line parameters for valid user
+ * input. If an invalid value is given, or if no user specified
+ * value exists, a default value is used. The final value is stored
+ * in a variable in the adapter structure.
+ **/
+void __devinit e1000e_check_options(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ int bd = adapter->bd_number;
+
+ if (bd >= E1000_MAX_NIC) {
+ e_notice("Warning: no configuration for board #%i\n", bd);
+ e_notice("Using defaults for all values\n");
+ }
+
+ { /* Transmit Interrupt Delay */
+ const struct e1000_option opt = {
+ .type = range_option,
+ .name = "Transmit Interrupt Delay",
+ .err = "using default of "
+ __MODULE_STRING(DEFAULT_TIDV),
+ .def = DEFAULT_TIDV,
+ .arg = { .r = { .min = MIN_TXDELAY,
+ .max = MAX_TXDELAY } }
+ };
+
+ if (num_TxIntDelay > bd) {
+ adapter->tx_int_delay = TxIntDelay[bd];
+ e1000_validate_option(&adapter->tx_int_delay, &opt,
+ adapter);
+ } else {
+ adapter->tx_int_delay = opt.def;
+ }
+ }
+ { /* Transmit Absolute Interrupt Delay */
+ const struct e1000_option opt = {
+ .type = range_option,
+ .name = "Transmit Absolute Interrupt Delay",
+ .err = "using default of "
+ __MODULE_STRING(DEFAULT_TADV),
+ .def = DEFAULT_TADV,
+ .arg = { .r = { .min = MIN_TXABSDELAY,
+ .max = MAX_TXABSDELAY } }
+ };
+
+ if (num_TxAbsIntDelay > bd) {
+ adapter->tx_abs_int_delay = TxAbsIntDelay[bd];
+ e1000_validate_option(&adapter->tx_abs_int_delay, &opt,
+ adapter);
+ } else {
+ adapter->tx_abs_int_delay = opt.def;
+ }
+ }
+ { /* Receive Interrupt Delay */
+ struct e1000_option opt = {
+ .type = range_option,
+ .name = "Receive Interrupt Delay",
+ .err = "using default of "
+ __MODULE_STRING(DEFAULT_RDTR),
+ .def = DEFAULT_RDTR,
+ .arg = { .r = { .min = MIN_RXDELAY,
+ .max = MAX_RXDELAY } }
+ };
+
+ if (num_RxIntDelay > bd) {
+ adapter->rx_int_delay = RxIntDelay[bd];
+ e1000_validate_option(&adapter->rx_int_delay, &opt,
+ adapter);
+ } else {
+ adapter->rx_int_delay = opt.def;
+ }
+ }
+ { /* Receive Absolute Interrupt Delay */
+ const struct e1000_option opt = {
+ .type = range_option,
+ .name = "Receive Absolute Interrupt Delay",
+ .err = "using default of "
+ __MODULE_STRING(DEFAULT_RADV),
+ .def = DEFAULT_RADV,
+ .arg = { .r = { .min = MIN_RXABSDELAY,
+ .max = MAX_RXABSDELAY } }
+ };
+
+ if (num_RxAbsIntDelay > bd) {
+ adapter->rx_abs_int_delay = RxAbsIntDelay[bd];
+ e1000_validate_option(&adapter->rx_abs_int_delay, &opt,
+ adapter);
+ } else {
+ adapter->rx_abs_int_delay = opt.def;
+ }
+ }
+ { /* Interrupt Throttling Rate */
+ const struct e1000_option opt = {
+ .type = range_option,
+ .name = "Interrupt Throttling Rate (ints/sec)",
+ .err = "using default of "
+ __MODULE_STRING(DEFAULT_ITR),
+ .def = DEFAULT_ITR,
+ .arg = { .r = { .min = MIN_ITR,
+ .max = MAX_ITR } }
+ };
+
+ if (num_InterruptThrottleRate > bd) {
+ adapter->itr = InterruptThrottleRate[bd];
+ switch (adapter->itr) {
+ case 0:
+ e_info("%s turned off\n", opt.name);
+ break;
+ case 1:
+ e_info("%s set to dynamic mode\n", opt.name);
+ adapter->itr_setting = adapter->itr;
+ adapter->itr = 20000;
+ break;
+ case 3:
+ e_info("%s set to dynamic conservative mode\n",
+ opt.name);
+ adapter->itr_setting = adapter->itr;
+ adapter->itr = 20000;
+ break;
+ default:
+ /*
+ * Save the setting, because the dynamic bits
+ * change itr.
+ */
+ if (e1000_validate_option(&adapter->itr, &opt,
+ adapter) &&
+ (adapter->itr == 3)) {
+ /*
+ * In case of invalid user value,
+ * default to conservative mode.
+ */
+ adapter->itr_setting = adapter->itr;
+ adapter->itr = 20000;
+ } else {
+ /*
+ * Clear the lower two bits because
+ * they are used as control.
+ */
+ adapter->itr_setting =
+ adapter->itr & ~3;
+ }
+ break;
+ }
+ } else {
+ adapter->itr_setting = opt.def;
+ adapter->itr = 20000;
+ }
+ }
+ { /* Interrupt Mode */
+ struct e1000_option opt = {
+ .type = range_option,
+ .name = "Interrupt Mode",
+ .err = "defaulting to 2 (MSI-X)",
+ .def = E1000E_INT_MODE_MSIX,
+ .arg = { .r = { .min = MIN_INTMODE,
+ .max = MAX_INTMODE } }
+ };
+
+ if (num_IntMode > bd) {
+ unsigned int int_mode = IntMode[bd];
+ e1000_validate_option(&int_mode, &opt, adapter);
+ adapter->int_mode = int_mode;
+ } else {
+ adapter->int_mode = opt.def;
+ }
+ }
+ { /* Smart Power Down */
+ const struct e1000_option opt = {
+ .type = enable_option,
+ .name = "PHY Smart Power Down",
+ .err = "defaulting to Disabled",
+ .def = OPTION_DISABLED
+ };
+
+ if (num_SmartPowerDownEnable > bd) {
+ unsigned int spd = SmartPowerDownEnable[bd];
+ e1000_validate_option(&spd, &opt, adapter);
+ if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN)
+ && spd)
+ adapter->flags |= FLAG_SMART_POWER_DOWN;
+ }
+ }
+ { /* Kumeran Lock Loss Workaround */
+ const struct e1000_option opt = {
+ .type = enable_option,
+ .name = "Kumeran Lock Loss Workaround",
+ .err = "defaulting to Enabled",
+ .def = OPTION_ENABLED
+ };
+
+ if (num_KumeranLockLoss > bd) {
+ unsigned int kmrn_lock_loss = KumeranLockLoss[bd];
+ e1000_validate_option(&kmrn_lock_loss, &opt, adapter);
+ if (hw->mac.type == e1000_ich8lan)
+ e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw,
+ kmrn_lock_loss);
+ } else {
+ if (hw->mac.type == e1000_ich8lan)
+ e1000e_set_kmrn_lock_loss_workaround_ich8lan(hw,
+ opt.def);
+ }
+ }
+ { /* Write-protect NVM */
+ const struct e1000_option opt = {
+ .type = enable_option,
+ .name = "Write-protect NVM",
+ .err = "defaulting to Enabled",
+ .def = OPTION_ENABLED
+ };
+
+ if (adapter->flags & FLAG_IS_ICH) {
+ if (num_WriteProtectNVM > bd) {
+ unsigned int write_protect_nvm = WriteProtectNVM[bd];
+ e1000_validate_option(&write_protect_nvm, &opt,
+ adapter);
+ if (write_protect_nvm)
+ adapter->flags |= FLAG_READ_ONLY_NVM;
+ } else {
+ if (opt.def)
+ adapter->flags |= FLAG_READ_ONLY_NVM;
+ }
+ }
+ }
+}
--- /dev/null
+/*******************************************************************************
+
+ Intel PRO/1000 Linux driver
+ Copyright(c) 1999 - 2008 Intel Corporation.
+
+ This program is free software; you can redistribute it and/or modify it
+ under the terms and conditions of the GNU General Public License,
+ version 2, as published by the Free Software Foundation.
+
+ This program is distributed in the hope it will be useful, but WITHOUT
+ ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ more details.
+
+ You should have received a copy of the GNU General Public License along with
+ this program; if not, write to the Free Software Foundation, Inc.,
+ 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+ The full GNU General Public License is included in this distribution in
+ the file called "COPYING".
+
+ Contact Information:
+ Linux NICS <linux.nics@intel.com>
+ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#include <linux/delay.h>
+
+#include "e1000.h"
+
+static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw);
+static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw);
+static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active);
+static s32 e1000_wait_autoneg(struct e1000_hw *hw);
+static u32 e1000_get_phy_addr_for_bm_page(u32 page, u32 reg);
+static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
+ u16 *data, bool read);
+
+/* Cable length tables */
+static const u16 e1000_m88_cable_length_table[] =
+ { 0, 50, 80, 110, 140, 140, E1000_CABLE_LENGTH_UNDEFINED };
+
+static const u16 e1000_igp_2_cable_length_table[] =
+ { 0, 0, 0, 0, 0, 0, 0, 0, 3, 5, 8, 11, 13, 16, 18, 21, 0, 0, 0, 3,
+ 6, 10, 13, 16, 19, 23, 26, 29, 32, 35, 38, 41, 6, 10, 14, 18, 22,
+ 26, 30, 33, 37, 41, 44, 48, 51, 54, 58, 61, 21, 26, 31, 35, 40,
+ 44, 49, 53, 57, 61, 65, 68, 72, 75, 79, 82, 40, 45, 51, 56, 61,
+ 66, 70, 75, 79, 83, 87, 91, 94, 98, 101, 104, 60, 66, 72, 77, 82,
+ 87, 92, 96, 100, 104, 108, 111, 114, 117, 119, 121, 83, 89, 95,
+ 100, 105, 109, 113, 116, 119, 122, 124, 104, 109, 114, 118, 121,
+ 124};
+#define IGP02E1000_CABLE_LENGTH_TABLE_SIZE \
+ ARRAY_SIZE(e1000_igp_2_cable_length_table)
+
+/**
+ * e1000e_check_reset_block_generic - Check if PHY reset is blocked
+ * @hw: pointer to the HW structure
+ *
+ * Read the PHY management control register and check whether a PHY reset
+ * is blocked. If a reset is not blocked return 0, otherwise
+ * return E1000_BLK_PHY_RESET (12).
+ **/
+s32 e1000e_check_reset_block_generic(struct e1000_hw *hw)
+{
+ u32 manc;
+
+ manc = er32(MANC);
+
+ return (manc & E1000_MANC_BLK_PHY_RST_ON_IDE) ?
+ E1000_BLK_PHY_RESET : 0;
+}
+
+/**
+ * e1000e_get_phy_id - Retrieve the PHY ID and revision
+ * @hw: pointer to the HW structure
+ *
+ * Reads the PHY registers and stores the PHY ID and possibly the PHY
+ * revision in the hardware structure.
+ **/
+s32 e1000e_get_phy_id(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_id;
+
+ ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
+ if (ret_val)
+ return ret_val;
+
+ phy->id = (u32)(phy_id << 16);
+ udelay(20);
+ ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
+ if (ret_val)
+ return ret_val;
+
+ phy->id |= (u32)(phy_id & PHY_REVISION_MASK);
+ phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
+
+ return 0;
+}
+
+/**
+ * e1000e_phy_reset_dsp - Reset PHY DSP
+ * @hw: pointer to the HW structure
+ *
+ * Reset the digital signal processor.
+ **/
+s32 e1000e_phy_reset_dsp(struct e1000_hw *hw)
+{
+ s32 ret_val;
+
+ ret_val = e1e_wphy(hw, M88E1000_PHY_GEN_CONTROL, 0xC1);
+ if (ret_val)
+ return ret_val;
+
+ return e1e_wphy(hw, M88E1000_PHY_GEN_CONTROL, 0);
+}
+
+/**
+ * e1000e_read_phy_reg_mdic - Read MDI control register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Reads the MDI control register in the PHY at offset and stores the
+ * information read to data.
+ **/
+s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ u32 i, mdic = 0;
+
+ if (offset > MAX_PHY_REG_ADDRESS) {
+ hw_dbg(hw, "PHY Address %d is out of range\n", offset);
+ return -E1000_ERR_PARAM;
+ }
+
+ /*
+ * Set up Op-code, Phy Address, and register offset in the MDI
+ * Control register. The MAC will take care of interfacing with the
+ * PHY to retrieve the desired data.
+ */
+ mdic = ((offset << E1000_MDIC_REG_SHIFT) |
+ (phy->addr << E1000_MDIC_PHY_SHIFT) |
+ (E1000_MDIC_OP_READ));
+
+ ew32(MDIC, mdic);
+
+ /*
+ * Poll the ready bit to see if the MDI read completed
+ * Increasing the time out as testing showed failures with
+ * the lower time out
+ */
+ for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) {
+ udelay(50);
+ mdic = er32(MDIC);
+ if (mdic & E1000_MDIC_READY)
+ break;
+ }
+ if (!(mdic & E1000_MDIC_READY)) {
+ hw_dbg(hw, "MDI Read did not complete\n");
+ return -E1000_ERR_PHY;
+ }
+ if (mdic & E1000_MDIC_ERROR) {
+ hw_dbg(hw, "MDI Error\n");
+ return -E1000_ERR_PHY;
+ }
+ *data = (u16) mdic;
+
+ return 0;
+}
+
+/**
+ * e1000e_write_phy_reg_mdic - Write MDI control register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write to register at offset
+ *
+ * Writes data to MDI control register in the PHY at offset.
+ **/
+s32 e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ u32 i, mdic = 0;
+
+ if (offset > MAX_PHY_REG_ADDRESS) {
+ hw_dbg(hw, "PHY Address %d is out of range\n", offset);
+ return -E1000_ERR_PARAM;
+ }
+
+ /*
+ * Set up Op-code, Phy Address, and register offset in the MDI
+ * Control register. The MAC will take care of interfacing with the
+ * PHY to retrieve the desired data.
+ */
+ mdic = (((u32)data) |
+ (offset << E1000_MDIC_REG_SHIFT) |
+ (phy->addr << E1000_MDIC_PHY_SHIFT) |
+ (E1000_MDIC_OP_WRITE));
+
+ ew32(MDIC, mdic);
+
+ /*
+ * Poll the ready bit to see if the MDI read completed
+ * Increasing the time out as testing showed failures with
+ * the lower time out
+ */
+ for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) {
+ udelay(50);
+ mdic = er32(MDIC);
+ if (mdic & E1000_MDIC_READY)
+ break;
+ }
+ if (!(mdic & E1000_MDIC_READY)) {
+ hw_dbg(hw, "MDI Write did not complete\n");
+ return -E1000_ERR_PHY;
+ }
+ if (mdic & E1000_MDIC_ERROR) {
+ hw_dbg(hw, "MDI Error\n");
+ return -E1000_ERR_PHY;
+ }
+
+ return 0;
+}
+
+/**
+ * e1000e_read_phy_reg_m88 - Read m88 PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and storing the retrieved information in data. Release any acquired
+ * semaphores before exiting.
+ **/
+s32 e1000e_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ s32 ret_val;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+ hw->phy.ops.release_phy(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_write_phy_reg_m88 - Write m88 PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore, if necessary, then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+s32 e1000e_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ s32 ret_val;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+ hw->phy.ops.release_phy(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_read_phy_reg_igp - Read igp PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and storing the retrieved information in data. Release any acquired
+ * semaphores before exiting.
+ **/
+s32 e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ s32 ret_val;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ IGP01E1000_PHY_PAGE_SELECT,
+ (u16)offset);
+ if (ret_val) {
+ hw->phy.ops.release_phy(hw);
+ return ret_val;
+ }
+ }
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+ hw->phy.ops.release_phy(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_write_phy_reg_igp - Write igp PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore, if necessary, then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+s32 e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ s32 ret_val;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+ ret_val = e1000e_write_phy_reg_mdic(hw,
+ IGP01E1000_PHY_PAGE_SELECT,
+ (u16)offset);
+ if (ret_val) {
+ hw->phy.ops.release_phy(hw);
+ return ret_val;
+ }
+ }
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+ hw->phy.ops.release_phy(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_read_kmrn_reg - Read kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore, if necessary. Then reads the PHY register at offset
+ * using the kumeran interface. The information retrieved is stored in data.
+ * Release any acquired semaphores before exiting.
+ **/
+s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ u32 kmrnctrlsta;
+ s32 ret_val;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
+ E1000_KMRNCTRLSTA_OFFSET) | E1000_KMRNCTRLSTA_REN;
+ ew32(KMRNCTRLSTA, kmrnctrlsta);
+
+ udelay(2);
+
+ kmrnctrlsta = er32(KMRNCTRLSTA);
+ *data = (u16)kmrnctrlsta;
+
+ hw->phy.ops.release_phy(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_write_kmrn_reg - Write kumeran register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore, if necessary. Then write the data to PHY register
+ * at the offset using the kumeran interface. Release any acquired semaphores
+ * before exiting.
+ **/
+s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ u32 kmrnctrlsta;
+ s32 ret_val;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
+ E1000_KMRNCTRLSTA_OFFSET) | data;
+ ew32(KMRNCTRLSTA, kmrnctrlsta);
+
+ udelay(2);
+ hw->phy.ops.release_phy(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_copper_link_setup_m88 - Setup m88 PHY's for copper link
+ * @hw: pointer to the HW structure
+ *
+ * Sets up MDI/MDI-X and polarity for m88 PHY's. If necessary, transmit clock
+ * and downshift values are set also.
+ **/
+s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+
+ /* Enable CRS on Tx. This must be set for half-duplex operation. */
+ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* For newer PHYs this bit is downshift enable */
+ if (phy->type == e1000_phy_m88)
+ phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+
+ /*
+ * Options:
+ * MDI/MDI-X = 0 (default)
+ * 0 - Auto for all speeds
+ * 1 - MDI mode
+ * 2 - MDI-X mode
+ * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
+ */
+ phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+
+ switch (phy->mdix) {
+ case 1:
+ phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
+ break;
+ case 2:
+ phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE;
+ break;
+ case 3:
+ phy_data |= M88E1000_PSCR_AUTO_X_1000T;
+ break;
+ case 0:
+ default:
+ phy_data |= M88E1000_PSCR_AUTO_X_MODE;
+ break;
+ }
+
+ /*
+ * Options:
+ * disable_polarity_correction = 0 (default)
+ * Automatic Correction for Reversed Cable Polarity
+ * 0 - Disabled
+ * 1 - Enabled
+ */
+ phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
+ if (phy->disable_polarity_correction == 1)
+ phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
+
+ /* Enable downshift on BM (disabled by default) */
+ if (phy->type == e1000_phy_bm)
+ phy_data |= BME1000_PSCR_ENABLE_DOWNSHIFT;
+
+ ret_val = e1e_wphy(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if ((phy->type == e1000_phy_m88) &&
+ (phy->revision < E1000_REVISION_4) &&
+ (phy->id != BME1000_E_PHY_ID_R2)) {
+ /*
+ * Force TX_CLK in the Extended PHY Specific Control Register
+ * to 25MHz clock.
+ */
+ ret_val = e1e_rphy(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_EPSCR_TX_CLK_25;
+
+ if ((phy->revision == 2) &&
+ (phy->id == M88E1111_I_PHY_ID)) {
+ /* 82573L PHY - set the downshift counter to 5x. */
+ phy_data &= ~M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK;
+ phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X;
+ } else {
+ /* Configure Master and Slave downshift values */
+ phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK |
+ M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
+ phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X |
+ M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
+ }
+ ret_val = e1e_wphy(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ if ((phy->type == e1000_phy_bm) && (phy->id == BME1000_E_PHY_ID_R2)) {
+ /* Set PHY page 0, register 29 to 0x0003 */
+ ret_val = e1e_wphy(hw, 29, 0x0003);
+ if (ret_val)
+ return ret_val;
+
+ /* Set PHY page 0, register 30 to 0x0000 */
+ ret_val = e1e_wphy(hw, 30, 0x0000);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Commit the changes. */
+ ret_val = e1000e_commit_phy(hw);
+ if (ret_val)
+ hw_dbg(hw, "Error committing the PHY changes\n");
+
+ return ret_val;
+}
+
+/**
+ * e1000e_copper_link_setup_igp - Setup igp PHY's for copper link
+ * @hw: pointer to the HW structure
+ *
+ * Sets up LPLU, MDI/MDI-X, polarity, Smartspeed and Master/Slave config for
+ * igp PHY's.
+ **/
+s32 e1000e_copper_link_setup_igp(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+
+ ret_val = e1000_phy_hw_reset(hw);
+ if (ret_val) {
+ hw_dbg(hw, "Error resetting the PHY.\n");
+ return ret_val;
+ }
+
+ /*
+ * Wait 100ms for MAC to configure PHY from NVM settings, to avoid
+ * timeout issues when LFS is enabled.
+ */
+ msleep(100);
+
+ /* disable lplu d0 during driver init */
+ ret_val = e1000_set_d0_lplu_state(hw, 0);
+ if (ret_val) {
+ hw_dbg(hw, "Error Disabling LPLU D0\n");
+ return ret_val;
+ }
+ /* Configure mdi-mdix settings */
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CTRL, &data);
+ if (ret_val)
+ return ret_val;
+
+ data &= ~IGP01E1000_PSCR_AUTO_MDIX;
+
+ switch (phy->mdix) {
+ case 1:
+ data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
+ break;
+ case 2:
+ data |= IGP01E1000_PSCR_FORCE_MDI_MDIX;
+ break;
+ case 0:
+ default:
+ data |= IGP01E1000_PSCR_AUTO_MDIX;
+ break;
+ }
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CTRL, data);
+ if (ret_val)
+ return ret_val;
+
+ /* set auto-master slave resolution settings */
+ if (hw->mac.autoneg) {
+ /*
+ * when autonegotiation advertisement is only 1000Mbps then we
+ * should disable SmartSpeed and enable Auto MasterSlave
+ * resolution as hardware default.
+ */
+ if (phy->autoneg_advertised == ADVERTISE_1000_FULL) {
+ /* Disable SmartSpeed */
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ return ret_val;
+
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ return ret_val;
+
+ /* Set auto Master/Slave resolution process */
+ ret_val = e1e_rphy(hw, PHY_1000T_CTRL, &data);
+ if (ret_val)
+ return ret_val;
+
+ data &= ~CR_1000T_MS_ENABLE;
+ ret_val = e1e_wphy(hw, PHY_1000T_CTRL, data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ ret_val = e1e_rphy(hw, PHY_1000T_CTRL, &data);
+ if (ret_val)
+ return ret_val;
+
+ /* load defaults for future use */
+ phy->original_ms_type = (data & CR_1000T_MS_ENABLE) ?
+ ((data & CR_1000T_MS_VALUE) ?
+ e1000_ms_force_master :
+ e1000_ms_force_slave) :
+ e1000_ms_auto;
+
+ switch (phy->ms_type) {
+ case e1000_ms_force_master:
+ data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE);
+ break;
+ case e1000_ms_force_slave:
+ data |= CR_1000T_MS_ENABLE;
+ data &= ~(CR_1000T_MS_VALUE);
+ break;
+ case e1000_ms_auto:
+ data &= ~CR_1000T_MS_ENABLE;
+ default:
+ break;
+ }
+ ret_val = e1e_wphy(hw, PHY_1000T_CTRL, data);
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000_phy_setup_autoneg - Configure PHY for auto-negotiation
+ * @hw: pointer to the HW structure
+ *
+ * Reads the MII auto-neg advertisement register and/or the 1000T control
+ * register and if the PHY is already setup for auto-negotiation, then
+ * return successful. Otherwise, setup advertisement and flow control to
+ * the appropriate values for the wanted auto-negotiation.
+ **/
+static s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 mii_autoneg_adv_reg;
+ u16 mii_1000t_ctrl_reg = 0;
+
+ phy->autoneg_advertised &= phy->autoneg_mask;
+
+ /* Read the MII Auto-Neg Advertisement Register (Address 4). */
+ ret_val = e1e_rphy(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
+ if (ret_val)
+ return ret_val;
+
+ if (phy->autoneg_mask & ADVERTISE_1000_FULL) {
+ /* Read the MII 1000Base-T Control Register (Address 9). */
+ ret_val = e1e_rphy(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /*
+ * Need to parse both autoneg_advertised and fc and set up
+ * the appropriate PHY registers. First we will parse for
+ * autoneg_advertised software override. Since we can advertise
+ * a plethora of combinations, we need to check each bit
+ * individually.
+ */
+
+ /*
+ * First we clear all the 10/100 mb speed bits in the Auto-Neg
+ * Advertisement Register (Address 4) and the 1000 mb speed bits in
+ * the 1000Base-T Control Register (Address 9).
+ */
+ mii_autoneg_adv_reg &= ~(NWAY_AR_100TX_FD_CAPS |
+ NWAY_AR_100TX_HD_CAPS |
+ NWAY_AR_10T_FD_CAPS |
+ NWAY_AR_10T_HD_CAPS);
+ mii_1000t_ctrl_reg &= ~(CR_1000T_HD_CAPS | CR_1000T_FD_CAPS);
+
+ hw_dbg(hw, "autoneg_advertised %x\n", phy->autoneg_advertised);
+
+ /* Do we want to advertise 10 Mb Half Duplex? */
+ if (phy->autoneg_advertised & ADVERTISE_10_HALF) {
+ hw_dbg(hw, "Advertise 10mb Half duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
+ }
+
+ /* Do we want to advertise 10 Mb Full Duplex? */
+ if (phy->autoneg_advertised & ADVERTISE_10_FULL) {
+ hw_dbg(hw, "Advertise 10mb Full duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
+ }
+
+ /* Do we want to advertise 100 Mb Half Duplex? */
+ if (phy->autoneg_advertised & ADVERTISE_100_HALF) {
+ hw_dbg(hw, "Advertise 100mb Half duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
+ }
+
+ /* Do we want to advertise 100 Mb Full Duplex? */
+ if (phy->autoneg_advertised & ADVERTISE_100_FULL) {
+ hw_dbg(hw, "Advertise 100mb Full duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
+ }
+
+ /* We do not allow the Phy to advertise 1000 Mb Half Duplex */
+ if (phy->autoneg_advertised & ADVERTISE_1000_HALF)
+ hw_dbg(hw, "Advertise 1000mb Half duplex request denied!\n");
+
+ /* Do we want to advertise 1000 Mb Full Duplex? */
+ if (phy->autoneg_advertised & ADVERTISE_1000_FULL) {
+ hw_dbg(hw, "Advertise 1000mb Full duplex\n");
+ mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
+ }
+
+ /*
+ * Check for a software override of the flow control settings, and
+ * setup the PHY advertisement registers accordingly. If
+ * auto-negotiation is enabled, then software will have to set the
+ * "PAUSE" bits to the correct value in the Auto-Negotiation
+ * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-
+ * negotiation.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames
+ * but we do not support receiving pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) are enabled.
+ * other: No software override. The flow control configuration
+ * in the EEPROM is used.
+ */
+ switch (hw->fc.type) {
+ case e1000_fc_none:
+ /*
+ * Flow control (Rx & Tx) is completely disabled by a
+ * software over-ride.
+ */
+ mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ case e1000_fc_rx_pause:
+ /*
+ * Rx Flow control is enabled, and Tx Flow control is
+ * disabled, by a software over-ride.
+ *
+ * Since there really isn't a way to advertise that we are
+ * capable of Rx Pause ONLY, we will advertise that we
+ * support both symmetric and asymmetric Rx PAUSE. Later
+ * (in e1000e_config_fc_after_link_up) we will disable the
+ * hw's ability to send PAUSE frames.
+ */
+ mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ case e1000_fc_tx_pause:
+ /*
+ * Tx Flow control is enabled, and Rx Flow control is
+ * disabled, by a software over-ride.
+ */
+ mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
+ mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
+ break;
+ case e1000_fc_full:
+ /*
+ * Flow control (both Rx and Tx) is enabled by a software
+ * over-ride.
+ */
+ mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ default:
+ hw_dbg(hw, "Flow control param set incorrectly\n");
+ ret_val = -E1000_ERR_CONFIG;
+ return ret_val;
+ }
+
+ ret_val = e1e_wphy(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
+ if (ret_val)
+ return ret_val;
+
+ hw_dbg(hw, "Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
+
+ if (phy->autoneg_mask & ADVERTISE_1000_FULL) {
+ ret_val = e1e_wphy(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000_copper_link_autoneg - Setup/Enable autoneg for copper link
+ * @hw: pointer to the HW structure
+ *
+ * Performs initial bounds checking on autoneg advertisement parameter, then
+ * configure to advertise the full capability. Setup the PHY to autoneg
+ * and restart the negotiation process between the link partner. If
+ * autoneg_wait_to_complete, then wait for autoneg to complete before exiting.
+ **/
+static s32 e1000_copper_link_autoneg(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_ctrl;
+
+ /*
+ * Perform some bounds checking on the autoneg advertisement
+ * parameter.
+ */
+ phy->autoneg_advertised &= phy->autoneg_mask;
+
+ /*
+ * If autoneg_advertised is zero, we assume it was not defaulted
+ * by the calling code so we set to advertise full capability.
+ */
+ if (phy->autoneg_advertised == 0)
+ phy->autoneg_advertised = phy->autoneg_mask;
+
+ hw_dbg(hw, "Reconfiguring auto-neg advertisement params\n");
+ ret_val = e1000_phy_setup_autoneg(hw);
+ if (ret_val) {
+ hw_dbg(hw, "Error Setting up Auto-Negotiation\n");
+ return ret_val;
+ }
+ hw_dbg(hw, "Restarting Auto-Neg\n");
+
+ /*
+ * Restart auto-negotiation by setting the Auto Neg Enable bit and
+ * the Auto Neg Restart bit in the PHY control register.
+ */
+ ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_ctrl);
+ if (ret_val)
+ return ret_val;
+
+ phy_ctrl |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
+ ret_val = e1e_wphy(hw, PHY_CONTROL, phy_ctrl);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Does the user want to wait for Auto-Neg to complete here, or
+ * check at a later time (for example, callback routine).
+ */
+ if (phy->autoneg_wait_to_complete) {
+ ret_val = e1000_wait_autoneg(hw);
+ if (ret_val) {
+ hw_dbg(hw, "Error while waiting for "
+ "autoneg to complete\n");
+ return ret_val;
+ }
+ }
+
+ hw->mac.get_link_status = 1;
+
+ return ret_val;
+}
+
+/**
+ * e1000e_setup_copper_link - Configure copper link settings
+ * @hw: pointer to the HW structure
+ *
+ * Calls the appropriate function to configure the link for auto-neg or forced
+ * speed and duplex. Then we check for link, once link is established calls
+ * to configure collision distance and flow control are called. If link is
+ * not established, we return -E1000_ERR_PHY (-2).
+ **/
+s32 e1000e_setup_copper_link(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ bool link;
+
+ if (hw->mac.autoneg) {
+ /*
+ * Setup autoneg and flow control advertisement and perform
+ * autonegotiation.
+ */
+ ret_val = e1000_copper_link_autoneg(hw);
+ if (ret_val)
+ return ret_val;
+ } else {
+ /*
+ * PHY will be set to 10H, 10F, 100H or 100F
+ * depending on user settings.
+ */
+ hw_dbg(hw, "Forcing Speed and Duplex\n");
+ ret_val = e1000_phy_force_speed_duplex(hw);
+ if (ret_val) {
+ hw_dbg(hw, "Error Forcing Speed and Duplex\n");
+ return ret_val;
+ }
+ }
+
+ /*
+ * Check link status. Wait up to 100 microseconds for link to become
+ * valid.
+ */
+ ret_val = e1000e_phy_has_link_generic(hw,
+ COPPER_LINK_UP_LIMIT,
+ 10,
+ &link);
+ if (ret_val)
+ return ret_val;
+
+ if (link) {
+ hw_dbg(hw, "Valid link established!!!\n");
+ e1000e_config_collision_dist(hw);
+ ret_val = e1000e_config_fc_after_link_up(hw);
+ } else {
+ hw_dbg(hw, "Unable to establish link!!!\n");
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000e_phy_force_speed_duplex_igp - Force speed/duplex for igp PHY
+ * @hw: pointer to the HW structure
+ *
+ * Calls the PHY setup function to force speed and duplex. Clears the
+ * auto-crossover to force MDI manually. Waits for link and returns
+ * successful if link up is successful, else -E1000_ERR_PHY (-2).
+ **/
+s32 e1000e_phy_force_speed_duplex_igp(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+ bool link;
+
+ ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
+
+ ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Clear Auto-Crossover to force MDI manually. IGP requires MDI
+ * forced whenever speed and duplex are forced.
+ */
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
+ phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
+
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ hw_dbg(hw, "IGP PSCR: %X\n", phy_data);
+
+ udelay(1);
+
+ if (phy->autoneg_wait_to_complete) {
+ hw_dbg(hw, "Waiting for forced speed/duplex link on IGP phy.\n");
+
+ ret_val = e1000e_phy_has_link_generic(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ return ret_val;
+
+ if (!link)
+ hw_dbg(hw, "Link taking longer than expected.\n");
+
+ /* Try once more */
+ ret_val = e1000e_phy_has_link_generic(hw,
+ PHY_FORCE_LIMIT,
+ 100000,
+ &link);
+ if (ret_val)
+ return ret_val;
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000e_phy_force_speed_duplex_m88 - Force speed/duplex for m88 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Calls the PHY setup function to force speed and duplex. Clears the
+ * auto-crossover to force MDI manually. Resets the PHY to commit the
+ * changes. If time expires while waiting for link up, we reset the DSP.
+ * After reset, TX_CLK and CRS on Tx must be set. Return successful upon
+ * successful completion, else return corresponding error code.
+ **/
+s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+ bool link;
+
+ /*
+ * Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
+ * forced whenever speed and duplex are forced.
+ */
+ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+ ret_val = e1e_wphy(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ hw_dbg(hw, "M88E1000 PSCR: %X\n", phy_data);
+
+ ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
+
+ /* Reset the phy to commit changes. */
+ phy_data |= MII_CR_RESET;
+
+ ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ udelay(1);
+
+ if (phy->autoneg_wait_to_complete) {
+ hw_dbg(hw, "Waiting for forced speed/duplex link on M88 phy.\n");
+
+ ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
+ 100000, &link);
+ if (ret_val)
+ return ret_val;
+
+ if (!link) {
+ /*
+ * We didn't get link.
+ * Reset the DSP and cross our fingers.
+ */
+ ret_val = e1e_wphy(hw, M88E1000_PHY_PAGE_SELECT,
+ 0x001d);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000e_phy_reset_dsp(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Try once more */
+ ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
+ 100000, &link);
+ if (ret_val)
+ return ret_val;
+ }
+
+ ret_val = e1e_rphy(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Resetting the phy means we need to re-force TX_CLK in the
+ * Extended PHY Specific Control Register to 25MHz clock from
+ * the reset value of 2.5MHz.
+ */
+ phy_data |= M88E1000_EPSCR_TX_CLK_25;
+ ret_val = e1e_wphy(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * In addition, we must re-enable CRS on Tx for both half and full
+ * duplex.
+ */
+ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+ ret_val = e1e_wphy(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_phy_force_speed_duplex_setup - Configure forced PHY speed/duplex
+ * @hw: pointer to the HW structure
+ * @phy_ctrl: pointer to current value of PHY_CONTROL
+ *
+ * Forces speed and duplex on the PHY by doing the following: disable flow
+ * control, force speed/duplex on the MAC, disable auto speed detection,
+ * disable auto-negotiation, configure duplex, configure speed, configure
+ * the collision distance, write configuration to CTRL register. The
+ * caller must write to the PHY_CONTROL register for these settings to
+ * take affect.
+ **/
+void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 ctrl;
+
+ /* Turn off flow control when forcing speed/duplex */
+ hw->fc.type = e1000_fc_none;
+
+ /* Force speed/duplex on the mac */
+ ctrl = er32(CTRL);
+ ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ctrl &= ~E1000_CTRL_SPD_SEL;
+
+ /* Disable Auto Speed Detection */
+ ctrl &= ~E1000_CTRL_ASDE;
+
+ /* Disable autoneg on the phy */
+ *phy_ctrl &= ~MII_CR_AUTO_NEG_EN;
+
+ /* Forcing Full or Half Duplex? */
+ if (mac->forced_speed_duplex & E1000_ALL_HALF_DUPLEX) {
+ ctrl &= ~E1000_CTRL_FD;
+ *phy_ctrl &= ~MII_CR_FULL_DUPLEX;
+ hw_dbg(hw, "Half Duplex\n");
+ } else {
+ ctrl |= E1000_CTRL_FD;
+ *phy_ctrl |= MII_CR_FULL_DUPLEX;
+ hw_dbg(hw, "Full Duplex\n");
+ }
+
+ /* Forcing 10mb or 100mb? */
+ if (mac->forced_speed_duplex & E1000_ALL_100_SPEED) {
+ ctrl |= E1000_CTRL_SPD_100;
+ *phy_ctrl |= MII_CR_SPEED_100;
+ *phy_ctrl &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10);
+ hw_dbg(hw, "Forcing 100mb\n");
+ } else {
+ ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
+ *phy_ctrl |= MII_CR_SPEED_10;
+ *phy_ctrl &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100);
+ hw_dbg(hw, "Forcing 10mb\n");
+ }
+
+ e1000e_config_collision_dist(hw);
+
+ ew32(CTRL, ctrl);
+}
+
+/**
+ * e1000e_set_d3_lplu_state - Sets low power link up state for D3
+ * @hw: pointer to the HW structure
+ * @active: boolean used to enable/disable lplu
+ *
+ * Success returns 0, Failure returns 1
+ *
+ * The low power link up (lplu) state is set to the power management level D3
+ * and SmartSpeed is disabled when active is true, else clear lplu for D3
+ * and enable Smartspeed. LPLU and Smartspeed are mutually exclusive. LPLU
+ * is used during Dx states where the power conservation is most important.
+ * During driver activity, SmartSpeed should be enabled so performance is
+ * maintained.
+ **/
+s32 e1000e_set_d3_lplu_state(struct e1000_hw *hw, bool active)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+
+ ret_val = e1e_rphy(hw, IGP02E1000_PHY_POWER_MGMT, &data);
+ if (ret_val)
+ return ret_val;
+
+ if (!active) {
+ data &= ~IGP02E1000_PM_D3_LPLU;
+ ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, data);
+ if (ret_val)
+ return ret_val;
+ /*
+ * LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ * during Dx states where the power conservation is most
+ * important. During driver activity we should enable
+ * SmartSpeed, so performance is maintained.
+ */
+ if (phy->smart_speed == e1000_smart_speed_on) {
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ return ret_val;
+
+ data |= IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ return ret_val;
+ } else if (phy->smart_speed == e1000_smart_speed_off) {
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ if (ret_val)
+ return ret_val;
+
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ return ret_val;
+ }
+ } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) ||
+ (phy->autoneg_advertised == E1000_ALL_NOT_GIG) ||
+ (phy->autoneg_advertised == E1000_ALL_10_SPEED)) {
+ data |= IGP02E1000_PM_D3_LPLU;
+ ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, data);
+ if (ret_val)
+ return ret_val;
+
+ /* When LPLU is enabled, we should disable SmartSpeed */
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data);
+ if (ret_val)
+ return ret_val;
+
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data);
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000e_check_downshift - Checks whether a downshift in speed occurred
+ * @hw: pointer to the HW structure
+ *
+ * Success returns 0, Failure returns 1
+ *
+ * A downshift is detected by querying the PHY link health.
+ **/
+s32 e1000e_check_downshift(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data, offset, mask;
+
+ switch (phy->type) {
+ case e1000_phy_m88:
+ case e1000_phy_gg82563:
+ offset = M88E1000_PHY_SPEC_STATUS;
+ mask = M88E1000_PSSR_DOWNSHIFT;
+ break;
+ case e1000_phy_igp_2:
+ case e1000_phy_igp_3:
+ offset = IGP01E1000_PHY_LINK_HEALTH;
+ mask = IGP01E1000_PLHR_SS_DOWNGRADE;
+ break;
+ default:
+ /* speed downshift not supported */
+ phy->speed_downgraded = 0;
+ return 0;
+ }
+
+ ret_val = e1e_rphy(hw, offset, &phy_data);
+
+ if (!ret_val)
+ phy->speed_downgraded = (phy_data & mask);
+
+ return ret_val;
+}
+
+/**
+ * e1000_check_polarity_m88 - Checks the polarity.
+ * @hw: pointer to the HW structure
+ *
+ * Success returns 0, Failure returns -E1000_ERR_PHY (-2)
+ *
+ * Polarity is determined based on the PHY specific status register.
+ **/
+static s32 e1000_check_polarity_m88(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+
+ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_STATUS, &data);
+
+ if (!ret_val)
+ phy->cable_polarity = (data & M88E1000_PSSR_REV_POLARITY)
+ ? e1000_rev_polarity_reversed
+ : e1000_rev_polarity_normal;
+
+ return ret_val;
+}
+
+/**
+ * e1000_check_polarity_igp - Checks the polarity.
+ * @hw: pointer to the HW structure
+ *
+ * Success returns 0, Failure returns -E1000_ERR_PHY (-2)
+ *
+ * Polarity is determined based on the PHY port status register, and the
+ * current speed (since there is no polarity at 100Mbps).
+ **/
+static s32 e1000_check_polarity_igp(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data, offset, mask;
+
+ /*
+ * Polarity is determined based on the speed of
+ * our connection.
+ */
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_STATUS, &data);
+ if (ret_val)
+ return ret_val;
+
+ if ((data & IGP01E1000_PSSR_SPEED_MASK) ==
+ IGP01E1000_PSSR_SPEED_1000MBPS) {
+ offset = IGP01E1000_PHY_PCS_INIT_REG;
+ mask = IGP01E1000_PHY_POLARITY_MASK;
+ } else {
+ /*
+ * This really only applies to 10Mbps since
+ * there is no polarity for 100Mbps (always 0).
+ */
+ offset = IGP01E1000_PHY_PORT_STATUS;
+ mask = IGP01E1000_PSSR_POLARITY_REVERSED;
+ }
+
+ ret_val = e1e_rphy(hw, offset, &data);
+
+ if (!ret_val)
+ phy->cable_polarity = (data & mask)
+ ? e1000_rev_polarity_reversed
+ : e1000_rev_polarity_normal;
+
+ return ret_val;
+}
+
+/**
+ * e1000_wait_autoneg - Wait for auto-neg completion
+ * @hw: pointer to the HW structure
+ *
+ * Waits for auto-negotiation to complete or for the auto-negotiation time
+ * limit to expire, which ever happens first.
+ **/
+static s32 e1000_wait_autoneg(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+ u16 i, phy_status;
+
+ /* Break after autoneg completes or PHY_AUTO_NEG_LIMIT expires. */
+ for (i = PHY_AUTO_NEG_LIMIT; i > 0; i--) {
+ ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+ if (ret_val)
+ break;
+ ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+ if (ret_val)
+ break;
+ if (phy_status & MII_SR_AUTONEG_COMPLETE)
+ break;
+ msleep(100);
+ }
+
+ /*
+ * PHY_AUTO_NEG_TIME expiration doesn't guarantee auto-negotiation
+ * has completed.
+ */
+ return ret_val;
+}
+
+/**
+ * e1000e_phy_has_link_generic - Polls PHY for link
+ * @hw: pointer to the HW structure
+ * @iterations: number of times to poll for link
+ * @usec_interval: delay between polling attempts
+ * @success: pointer to whether polling was successful or not
+ *
+ * Polls the PHY status register for link, 'iterations' number of times.
+ **/
+s32 e1000e_phy_has_link_generic(struct e1000_hw *hw, u32 iterations,
+ u32 usec_interval, bool *success)
+{
+ s32 ret_val = 0;
+ u16 i, phy_status;
+
+ for (i = 0; i < iterations; i++) {
+ /*
+ * Some PHYs require the PHY_STATUS register to be read
+ * twice due to the link bit being sticky. No harm doing
+ * it across the board.
+ */
+ ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+ if (ret_val)
+ break;
+ ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+ if (ret_val)
+ break;
+ if (phy_status & MII_SR_LINK_STATUS)
+ break;
+ if (usec_interval >= 1000)
+ mdelay(usec_interval/1000);
+ else
+ udelay(usec_interval);
+ }
+
+ *success = (i < iterations);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_get_cable_length_m88 - Determine cable length for m88 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Reads the PHY specific status register to retrieve the cable length
+ * information. The cable length is determined by averaging the minimum and
+ * maximum values to get the "average" cable length. The m88 PHY has four
+ * possible cable length values, which are:
+ * Register Value Cable Length
+ * 0 < 50 meters
+ * 1 50 - 80 meters
+ * 2 80 - 110 meters
+ * 3 110 - 140 meters
+ * 4 > 140 meters
+ **/
+s32 e1000e_get_cable_length_m88(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data, index;
+
+ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ index = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
+ M88E1000_PSSR_CABLE_LENGTH_SHIFT;
+ phy->min_cable_length = e1000_m88_cable_length_table[index];
+ phy->max_cable_length = e1000_m88_cable_length_table[index+1];
+
+ phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2;
+
+ return ret_val;
+}
+
+/**
+ * e1000e_get_cable_length_igp_2 - Determine cable length for igp2 PHY
+ * @hw: pointer to the HW structure
+ *
+ * The automatic gain control (agc) normalizes the amplitude of the
+ * received signal, adjusting for the attenuation produced by the
+ * cable. By reading the AGC registers, which represent the
+ * combination of course and fine gain value, the value can be put
+ * into a lookup table to obtain the approximate cable length
+ * for each channel.
+ **/
+s32 e1000e_get_cable_length_igp_2(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data, i, agc_value = 0;
+ u16 cur_agc_index, max_agc_index = 0;
+ u16 min_agc_index = IGP02E1000_CABLE_LENGTH_TABLE_SIZE - 1;
+ u16 agc_reg_array[IGP02E1000_PHY_CHANNEL_NUM] =
+ {IGP02E1000_PHY_AGC_A,
+ IGP02E1000_PHY_AGC_B,
+ IGP02E1000_PHY_AGC_C,
+ IGP02E1000_PHY_AGC_D};
+
+ /* Read the AGC registers for all channels */
+ for (i = 0; i < IGP02E1000_PHY_CHANNEL_NUM; i++) {
+ ret_val = e1e_rphy(hw, agc_reg_array[i], &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Getting bits 15:9, which represent the combination of
+ * course and fine gain values. The result is a number
+ * that can be put into the lookup table to obtain the
+ * approximate cable length.
+ */
+ cur_agc_index = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) &
+ IGP02E1000_AGC_LENGTH_MASK;
+
+ /* Array index bound check. */
+ if ((cur_agc_index >= IGP02E1000_CABLE_LENGTH_TABLE_SIZE) ||
+ (cur_agc_index == 0))
+ return -E1000_ERR_PHY;
+
+ /* Remove min & max AGC values from calculation. */
+ if (e1000_igp_2_cable_length_table[min_agc_index] >
+ e1000_igp_2_cable_length_table[cur_agc_index])
+ min_agc_index = cur_agc_index;
+ if (e1000_igp_2_cable_length_table[max_agc_index] <
+ e1000_igp_2_cable_length_table[cur_agc_index])
+ max_agc_index = cur_agc_index;
+
+ agc_value += e1000_igp_2_cable_length_table[cur_agc_index];
+ }
+
+ agc_value -= (e1000_igp_2_cable_length_table[min_agc_index] +
+ e1000_igp_2_cable_length_table[max_agc_index]);
+ agc_value /= (IGP02E1000_PHY_CHANNEL_NUM - 2);
+
+ /* Calculate cable length with the error range of +/- 10 meters. */
+ phy->min_cable_length = ((agc_value - IGP02E1000_AGC_RANGE) > 0) ?
+ (agc_value - IGP02E1000_AGC_RANGE) : 0;
+ phy->max_cable_length = agc_value + IGP02E1000_AGC_RANGE;
+
+ phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2;
+
+ return ret_val;
+}
+
+/**
+ * e1000e_get_phy_info_m88 - Retrieve PHY information
+ * @hw: pointer to the HW structure
+ *
+ * Valid for only copper links. Read the PHY status register (sticky read)
+ * to verify that link is up. Read the PHY special control register to
+ * determine the polarity and 10base-T extended distance. Read the PHY
+ * special status register to determine MDI/MDIx and current speed. If
+ * speed is 1000, then determine cable length, local and remote receiver.
+ **/
+s32 e1000e_get_phy_info_m88(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 phy_data;
+ bool link;
+
+ if (hw->phy.media_type != e1000_media_type_copper) {
+ hw_dbg(hw, "Phy info is only valid for copper media\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
+ if (ret_val)
+ return ret_val;
+
+ if (!link) {
+ hw_dbg(hw, "Phy info is only valid if link is up\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy->polarity_correction = (phy_data &
+ M88E1000_PSCR_POLARITY_REVERSAL);
+
+ ret_val = e1000_check_polarity_m88(hw);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy->is_mdix = (phy_data & M88E1000_PSSR_MDIX);
+
+ if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) {
+ ret_val = e1000_get_cable_length(hw);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1e_rphy(hw, PHY_1000T_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy->local_rx = (phy_data & SR_1000T_LOCAL_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+
+ phy->remote_rx = (phy_data & SR_1000T_REMOTE_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+ } else {
+ /* Set values to "undefined" */
+ phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
+ phy->local_rx = e1000_1000t_rx_status_undefined;
+ phy->remote_rx = e1000_1000t_rx_status_undefined;
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000e_get_phy_info_igp - Retrieve igp PHY information
+ * @hw: pointer to the HW structure
+ *
+ * Read PHY status to determine if link is up. If link is up, then
+ * set/determine 10base-T extended distance and polarity correction. Read
+ * PHY port status to determine MDI/MDIx and speed. Based on the speed,
+ * determine on the cable length, local and remote receiver.
+ **/
+s32 e1000e_get_phy_info_igp(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+ bool link;
+
+ ret_val = e1000e_phy_has_link_generic(hw, 1, 0, &link);
+ if (ret_val)
+ return ret_val;
+
+ if (!link) {
+ hw_dbg(hw, "Phy info is only valid if link is up\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ phy->polarity_correction = 1;
+
+ ret_val = e1000_check_polarity_igp(hw);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_STATUS, &data);
+ if (ret_val)
+ return ret_val;
+
+ phy->is_mdix = (data & IGP01E1000_PSSR_MDIX);
+
+ if ((data & IGP01E1000_PSSR_SPEED_MASK) ==
+ IGP01E1000_PSSR_SPEED_1000MBPS) {
+ ret_val = e1000_get_cable_length(hw);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1e_rphy(hw, PHY_1000T_STATUS, &data);
+ if (ret_val)
+ return ret_val;
+
+ phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+
+ phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS)
+ ? e1000_1000t_rx_status_ok
+ : e1000_1000t_rx_status_not_ok;
+ } else {
+ phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
+ phy->local_rx = e1000_1000t_rx_status_undefined;
+ phy->remote_rx = e1000_1000t_rx_status_undefined;
+ }
+
+ return ret_val;
+}
+
+/**
+ * e1000e_phy_sw_reset - PHY software reset
+ * @hw: pointer to the HW structure
+ *
+ * Does a software reset of the PHY by reading the PHY control register and
+ * setting/write the control register reset bit to the PHY.
+ **/
+s32 e1000e_phy_sw_reset(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 phy_ctrl;
+
+ ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_ctrl);
+ if (ret_val)
+ return ret_val;
+
+ phy_ctrl |= MII_CR_RESET;
+ ret_val = e1e_wphy(hw, PHY_CONTROL, phy_ctrl);
+ if (ret_val)
+ return ret_val;
+
+ udelay(1);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_phy_hw_reset_generic - PHY hardware reset
+ * @hw: pointer to the HW structure
+ *
+ * Verify the reset block is not blocking us from resetting. Acquire
+ * semaphore (if necessary) and read/set/write the device control reset
+ * bit in the PHY. Wait the appropriate delay time for the device to
+ * reset and release the semaphore (if necessary).
+ **/
+s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u32 ctrl;
+
+ ret_val = e1000_check_reset_block(hw);
+ if (ret_val)
+ return 0;
+
+ ret_val = phy->ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ ctrl = er32(CTRL);
+ ew32(CTRL, ctrl | E1000_CTRL_PHY_RST);
+ e1e_flush();
+
+ udelay(phy->reset_delay_us);
+
+ ew32(CTRL, ctrl);
+ e1e_flush();
+
+ udelay(150);
+
+ phy->ops.release_phy(hw);
+
+ return e1000_get_phy_cfg_done(hw);
+}
+
+/**
+ * e1000e_get_cfg_done - Generic configuration done
+ * @hw: pointer to the HW structure
+ *
+ * Generic function to wait 10 milli-seconds for configuration to complete
+ * and return success.
+ **/
+s32 e1000e_get_cfg_done(struct e1000_hw *hw)
+{
+ mdelay(10);
+ return 0;
+}
+
+/**
+ * e1000e_phy_init_script_igp3 - Inits the IGP3 PHY
+ * @hw: pointer to the HW structure
+ *
+ * Initializes a Intel Gigabit PHY3 when an EEPROM is not present.
+ **/
+s32 e1000e_phy_init_script_igp3(struct e1000_hw *hw)
+{
+ hw_dbg(hw, "Running IGP 3 PHY init script\n");
+
+ /* PHY init IGP 3 */
+ /* Enable rise/fall, 10-mode work in class-A */
+ e1e_wphy(hw, 0x2F5B, 0x9018);
+ /* Remove all caps from Replica path filter */
+ e1e_wphy(hw, 0x2F52, 0x0000);
+ /* Bias trimming for ADC, AFE and Driver (Default) */
+ e1e_wphy(hw, 0x2FB1, 0x8B24);
+ /* Increase Hybrid poly bias */
+ e1e_wphy(hw, 0x2FB2, 0xF8F0);
+ /* Add 4% to Tx amplitude in Gig mode */
+ e1e_wphy(hw, 0x2010, 0x10B0);
+ /* Disable trimming (TTT) */
+ e1e_wphy(hw, 0x2011, 0x0000);
+ /* Poly DC correction to 94.6% + 2% for all channels */
+ e1e_wphy(hw, 0x20DD, 0x249A);
+ /* ABS DC correction to 95.9% */
+ e1e_wphy(hw, 0x20DE, 0x00D3);
+ /* BG temp curve trim */
+ e1e_wphy(hw, 0x28B4, 0x04CE);
+ /* Increasing ADC OPAMP stage 1 currents to max */
+ e1e_wphy(hw, 0x2F70, 0x29E4);
+ /* Force 1000 ( required for enabling PHY regs configuration) */
+ e1e_wphy(hw, 0x0000, 0x0140);
+ /* Set upd_freq to 6 */
+ e1e_wphy(hw, 0x1F30, 0x1606);
+ /* Disable NPDFE */
+ e1e_wphy(hw, 0x1F31, 0xB814);
+ /* Disable adaptive fixed FFE (Default) */
+ e1e_wphy(hw, 0x1F35, 0x002A);
+ /* Enable FFE hysteresis */
+ e1e_wphy(hw, 0x1F3E, 0x0067);
+ /* Fixed FFE for short cable lengths */
+ e1e_wphy(hw, 0x1F54, 0x0065);
+ /* Fixed FFE for medium cable lengths */
+ e1e_wphy(hw, 0x1F55, 0x002A);
+ /* Fixed FFE for long cable lengths */
+ e1e_wphy(hw, 0x1F56, 0x002A);
+ /* Enable Adaptive Clip Threshold */
+ e1e_wphy(hw, 0x1F72, 0x3FB0);
+ /* AHT reset limit to 1 */
+ e1e_wphy(hw, 0x1F76, 0xC0FF);
+ /* Set AHT master delay to 127 msec */
+ e1e_wphy(hw, 0x1F77, 0x1DEC);
+ /* Set scan bits for AHT */
+ e1e_wphy(hw, 0x1F78, 0xF9EF);
+ /* Set AHT Preset bits */
+ e1e_wphy(hw, 0x1F79, 0x0210);
+ /* Change integ_factor of channel A to 3 */
+ e1e_wphy(hw, 0x1895, 0x0003);
+ /* Change prop_factor of channels BCD to 8 */
+ e1e_wphy(hw, 0x1796, 0x0008);
+ /* Change cg_icount + enable integbp for channels BCD */
+ e1e_wphy(hw, 0x1798, 0xD008);
+ /*
+ * Change cg_icount + enable integbp + change prop_factor_master
+ * to 8 for channel A
+ */
+ e1e_wphy(hw, 0x1898, 0xD918);
+ /* Disable AHT in Slave mode on channel A */
+ e1e_wphy(hw, 0x187A, 0x0800);
+ /*
+ * Enable LPLU and disable AN to 1000 in non-D0a states,
+ * Enable SPD+B2B
+ */
+ e1e_wphy(hw, 0x0019, 0x008D);
+ /* Enable restart AN on an1000_dis change */
+ e1e_wphy(hw, 0x001B, 0x2080);
+ /* Enable wh_fifo read clock in 10/100 modes */
+ e1e_wphy(hw, 0x0014, 0x0045);
+ /* Restart AN, Speed selection is 1000 */
+ e1e_wphy(hw, 0x0000, 0x1340);
+
+ return 0;
+}
+
+/* Internal function pointers */
+
+/**
+ * e1000_get_phy_cfg_done - Generic PHY configuration done
+ * @hw: pointer to the HW structure
+ *
+ * Return success if silicon family did not implement a family specific
+ * get_cfg_done function.
+ **/
+static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw)
+{
+ if (hw->phy.ops.get_cfg_done)
+ return hw->phy.ops.get_cfg_done(hw);
+
+ return 0;
+}
+
+/**
+ * e1000_phy_force_speed_duplex - Generic force PHY speed/duplex
+ * @hw: pointer to the HW structure
+ *
+ * When the silicon family has not implemented a forced speed/duplex
+ * function for the PHY, simply return 0.
+ **/
+static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw)
+{
+ if (hw->phy.ops.force_speed_duplex)
+ return hw->phy.ops.force_speed_duplex(hw);
+
+ return 0;
+}
+
+/**
+ * e1000e_get_phy_type_from_id - Get PHY type from id
+ * @phy_id: phy_id read from the phy
+ *
+ * Returns the phy type from the id.
+ **/
+enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id)
+{
+ enum e1000_phy_type phy_type = e1000_phy_unknown;
+
+ switch (phy_id) {
+ case M88E1000_I_PHY_ID:
+ case M88E1000_E_PHY_ID:
+ case M88E1111_I_PHY_ID:
+ case M88E1011_I_PHY_ID:
+ phy_type = e1000_phy_m88;
+ break;
+ case IGP01E1000_I_PHY_ID: /* IGP 1 & 2 share this */
+ phy_type = e1000_phy_igp_2;
+ break;
+ case GG82563_E_PHY_ID:
+ phy_type = e1000_phy_gg82563;
+ break;
+ case IGP03E1000_E_PHY_ID:
+ phy_type = e1000_phy_igp_3;
+ break;
+ case IFE_E_PHY_ID:
+ case IFE_PLUS_E_PHY_ID:
+ case IFE_C_E_PHY_ID:
+ phy_type = e1000_phy_ife;
+ break;
+ case BME1000_E_PHY_ID:
+ case BME1000_E_PHY_ID_R2:
+ phy_type = e1000_phy_bm;
+ break;
+ default:
+ phy_type = e1000_phy_unknown;
+ break;
+ }
+ return phy_type;
+}
+
+/**
+ * e1000e_determine_phy_address - Determines PHY address.
+ * @hw: pointer to the HW structure
+ *
+ * This uses a trial and error method to loop through possible PHY
+ * addresses. It tests each by reading the PHY ID registers and
+ * checking for a match.
+ **/
+s32 e1000e_determine_phy_address(struct e1000_hw *hw)
+{
+ s32 ret_val = -E1000_ERR_PHY_TYPE;
+ u32 phy_addr= 0;
+ u32 i = 0;
+ enum e1000_phy_type phy_type = e1000_phy_unknown;
+
+ do {
+ for (phy_addr = 0; phy_addr < 4; phy_addr++) {
+ hw->phy.addr = phy_addr;
+ e1000e_get_phy_id(hw);
+ phy_type = e1000e_get_phy_type_from_id(hw->phy.id);
+
+ /*
+ * If phy_type is valid, break - we found our
+ * PHY address
+ */
+ if (phy_type != e1000_phy_unknown) {
+ ret_val = 0;
+ break;
+ }
+ }
+ i++;
+ } while ((ret_val != 0) && (i < 100));
+
+ return ret_val;
+}
+
+/**
+ * e1000_get_phy_addr_for_bm_page - Retrieve PHY page address
+ * @page: page to access
+ *
+ * Returns the phy address for the page requested.
+ **/
+static u32 e1000_get_phy_addr_for_bm_page(u32 page, u32 reg)
+{
+ u32 phy_addr = 2;
+
+ if ((page >= 768) || (page == 0 && reg == 25) || (reg == 31))
+ phy_addr = 1;
+
+ return phy_addr;
+}
+
+/**
+ * e1000e_write_phy_reg_bm - Write BM PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore, if necessary, then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ s32 ret_val;
+ u32 page_select = 0;
+ u32 page = offset >> IGP_PAGE_SHIFT;
+ u32 page_shift = 0;
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, &data,
+ false);
+ goto out;
+ }
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ goto out;
+
+ hw->phy.addr = e1000_get_phy_addr_for_bm_page(page, offset);
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+ /*
+ * Page select is register 31 for phy address 1 and 22 for
+ * phy address 2 and 3. Page select is shifted only for
+ * phy address 1.
+ */
+ if (hw->phy.addr == 1) {
+ page_shift = IGP_PAGE_SHIFT;
+ page_select = IGP01E1000_PHY_PAGE_SELECT;
+ } else {
+ page_shift = 0;
+ page_select = BM_PHY_PAGE_SELECT;
+ }
+
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw, page_select,
+ (page << page_shift));
+ if (ret_val) {
+ hw->phy.ops.release_phy(hw);
+ goto out;
+ }
+ }
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+ hw->phy.ops.release_phy(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_read_phy_reg_bm - Read BM PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and storing the retrieved information in data. Release any acquired
+ * semaphores before exiting.
+ **/
+s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ s32 ret_val;
+ u32 page_select = 0;
+ u32 page = offset >> IGP_PAGE_SHIFT;
+ u32 page_shift = 0;
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, data,
+ true);
+ goto out;
+ }
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ goto out;
+
+ hw->phy.addr = e1000_get_phy_addr_for_bm_page(page, offset);
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+ /*
+ * Page select is register 31 for phy address 1 and 22 for
+ * phy address 2 and 3. Page select is shifted only for
+ * phy address 1.
+ */
+ if (hw->phy.addr == 1) {
+ page_shift = IGP_PAGE_SHIFT;
+ page_select = IGP01E1000_PHY_PAGE_SELECT;
+ } else {
+ page_shift = 0;
+ page_select = BM_PHY_PAGE_SELECT;
+ }
+
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw, page_select,
+ (page << page_shift));
+ if (ret_val) {
+ hw->phy.ops.release_phy(hw);
+ goto out;
+ }
+ }
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+ hw->phy.ops.release_phy(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000e_read_phy_reg_bm2 - Read BM PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and storing the retrieved information in data. Release any acquired
+ * semaphores before exiting.
+ **/
+s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ s32 ret_val;
+ u16 page = (u16)(offset >> IGP_PAGE_SHIFT);
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, data,
+ true);
+ return ret_val;
+ }
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ hw->phy.addr = 1;
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_PHY_PAGE_SELECT,
+ page);
+
+ if (ret_val) {
+ hw->phy.ops.release_phy(hw);
+ return ret_val;
+ }
+ }
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+ hw->phy.ops.release_phy(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000e_write_phy_reg_bm2 - Write BM PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore, if necessary, then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ **/
+s32 e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ s32 ret_val;
+ u16 page = (u16)(offset >> IGP_PAGE_SHIFT);
+
+ /* Page 800 works differently than the rest so it has its own func */
+ if (page == BM_WUC_PAGE) {
+ ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, &data,
+ false);
+ return ret_val;
+ }
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ hw->phy.addr = 1;
+
+ if (offset > MAX_PHY_MULTI_PAGE_REG) {
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_PHY_PAGE_SELECT,
+ page);
+
+ if (ret_val) {
+ hw->phy.ops.release_phy(hw);
+ return ret_val;
+ }
+ }
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
+ data);
+
+ hw->phy.ops.release_phy(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_access_phy_wakeup_reg_bm - Read BM PHY wakeup register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read or written
+ * @data: pointer to the data to read or write
+ * @read: determines if operation is read or write
+ *
+ * Acquires semaphore, if necessary, then reads the PHY register at offset
+ * and storing the retrieved information in data. Release any acquired
+ * semaphores before exiting. Note that procedure to read the wakeup
+ * registers are different. It works as such:
+ * 1) Set page 769, register 17, bit 2 = 1
+ * 2) Set page to 800 for host (801 if we were manageability)
+ * 3) Write the address using the address opcode (0x11)
+ * 4) Read or write the data using the data opcode (0x12)
+ * 5) Restore 769_17.2 to its original value
+ **/
+static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
+ u16 *data, bool read)
+{
+ s32 ret_val;
+ u16 reg = ((u16)offset) & PHY_REG_MASK;
+ u16 phy_reg = 0;
+ u8 phy_acquired = 1;
+
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val) {
+ phy_acquired = 0;
+ goto out;
+ }
+
+ /* All operations in this function are phy address 1 */
+ hw->phy.addr = 1;
+
+ /* Set page 769 */
+ e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT));
+
+ ret_val = e1000e_read_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, &phy_reg);
+ if (ret_val)
+ goto out;
+
+ /* First clear bit 4 to avoid a power state change */
+ phy_reg &= ~(BM_WUC_HOST_WU_BIT);
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg);
+ if (ret_val)
+ goto out;
+
+ /* Write bit 2 = 1, and clear bit 4 to 769_17 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG,
+ phy_reg | BM_WUC_ENABLE_BIT);
+ if (ret_val)
+ goto out;
+
+ /* Select page 800 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (BM_WUC_PAGE << IGP_PAGE_SHIFT));
+
+ /* Write the page 800 offset value using opcode 0x11 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ADDRESS_OPCODE, reg);
+ if (ret_val)
+ goto out;
+
+ if (read) {
+ /* Read the page 800 value using opcode 0x12 */
+ ret_val = e1000e_read_phy_reg_mdic(hw, BM_WUC_DATA_OPCODE,
+ data);
+ } else {
+ /* Read the page 800 value using opcode 0x12 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_DATA_OPCODE,
+ *data);
+ }
+
+ if (ret_val)
+ goto out;
+
+ /*
+ * Restore 769_17.2 to its original value
+ * Set page 769
+ */
+ e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT));
+
+ /* Clear 769_17.2 */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg);
+
+out:
+ if (phy_acquired == 1)
+ hw->phy.ops.release_phy(hw);
+ return ret_val;
+}
+
+/**
+ * e1000e_commit_phy - Soft PHY reset
+ * @hw: pointer to the HW structure
+ *
+ * Performs a soft PHY reset on those that apply. This is a function pointer
+ * entry point called by drivers.
+ **/
+s32 e1000e_commit_phy(struct e1000_hw *hw)
+{
+ if (hw->phy.ops.commit_phy)
+ return hw->phy.ops.commit_phy(hw);
+
+ return 0;
+}
+
+/**
+ * e1000_set_d0_lplu_state - Sets low power link up state for D0
+ * @hw: pointer to the HW structure
+ * @active: boolean used to enable/disable lplu
+ *
+ * Success returns 0, Failure returns 1
+ *
+ * The low power link up (lplu) state is set to the power management level D0
+ * and SmartSpeed is disabled when active is true, else clear lplu for D0
+ * and enable Smartspeed. LPLU and Smartspeed are mutually exclusive. LPLU
+ * is used during Dx states where the power conservation is most important.
+ * During driver activity, SmartSpeed should be enabled so performance is
+ * maintained. This is a function pointer entry point called by drivers.
+ **/
+static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active)
+{
+ if (hw->phy.ops.set_d0_lplu_state)
+ return hw->phy.ops.set_d0_lplu_state(hw, active);
+
+ return 0;
+}
projects / legacy / linux-2.6.18-xen.git / commitdiff