ia64/linux-2.6.18-xen.hg

annotate kernel/Makefile @ 798:b02a90bf5bbc

ACPI: Backport missing part for T-State MSR support

Part of below kernel commit was missed while packporting T-State
support.

commit f79f06ab9f86d7203006d2ec8992ac80df36a34e
Author: Zhao Yakui <yakui.zhao@intel.com>
Date: Thu Nov 15 17:06:36 2007 +0800

ACPI: Enable MSR (FixedHW) support for T-States

Add throttling control via MSR when T-states uses
the FixHW Control Status registers.

Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Signed-off-by: Wei Gang <gang.wei@intel.com>
author Keir Fraser <keir.fraser@citrix.com>
date Mon Mar 02 10:53:59 2009 +0000 (2009-03-02)
parents 831230e53067
children
rev   line source
ian@0 1 #
ian@0 2 # Makefile for the linux kernel.
ian@0 3 #
ian@0 4
ian@0 5 obj-y = sched.o fork.o exec_domain.o panic.o printk.o profile.o \
ian@0 6 exit.o itimer.o time.o softirq.o resource.o \
ian@0 7 sysctl.o capability.o ptrace.o timer.o user.o \
ian@0 8 signal.o sys.o kmod.o workqueue.o pid.o \
ian@0 9 rcupdate.o extable.o params.o posix-timers.o \
ian@0 10 kthread.o wait.o kfifo.o sys_ni.o posix-cpu-timers.o mutex.o \
ian@0 11 hrtimer.o rwsem.o
ian@0 12
ian@0 13 obj-$(CONFIG_STACKTRACE) += stacktrace.o
ian@0 14 obj-y += time/
ian@0 15 obj-$(CONFIG_DEBUG_MUTEXES) += mutex-debug.o
ian@0 16 obj-$(CONFIG_LOCKDEP) += lockdep.o
ian@0 17 ifeq ($(CONFIG_PROC_FS),y)
ian@0 18 obj-$(CONFIG_LOCKDEP) += lockdep_proc.o
ian@0 19 endif
ian@0 20 obj-$(CONFIG_FUTEX) += futex.o
ian@0 21 ifeq ($(CONFIG_COMPAT),y)
ian@0 22 obj-$(CONFIG_FUTEX) += futex_compat.o
ian@0 23 endif
ian@0 24 obj-$(CONFIG_RT_MUTEXES) += rtmutex.o
ian@0 25 obj-$(CONFIG_DEBUG_RT_MUTEXES) += rtmutex-debug.o
ian@0 26 obj-$(CONFIG_RT_MUTEX_TESTER) += rtmutex-tester.o
ian@0 27 obj-$(CONFIG_GENERIC_ISA_DMA) += dma.o
ian@0 28 obj-$(CONFIG_SMP) += cpu.o spinlock.o
ian@0 29 obj-$(CONFIG_DEBUG_SPINLOCK) += spinlock.o
ian@0 30 obj-$(CONFIG_PROVE_LOCKING) += spinlock.o
ian@0 31 obj-$(CONFIG_UID16) += uid16.o
ian@0 32 obj-$(CONFIG_MODULES) += module.o
ian@0 33 obj-$(CONFIG_KALLSYMS) += kallsyms.o
ian@0 34 obj-$(CONFIG_STACK_UNWIND) += unwind.o
ian@0 35 obj-$(CONFIG_PM) += power/
ian@0 36 obj-$(CONFIG_BSD_PROCESS_ACCT) += acct.o
ian@0 37 obj-$(CONFIG_KEXEC) += kexec.o
ian@0 38 obj-$(CONFIG_COMPAT) += compat.o
ian@0 39 obj-$(CONFIG_CPUSETS) += cpuset.o
ian@0 40 obj-$(CONFIG_IKCONFIG) += configs.o
ian@0 41 obj-$(CONFIG_STOP_MACHINE) += stop_machine.o
ian@0 42 obj-$(CONFIG_AUDIT) += audit.o auditfilter.o
ian@0 43 obj-$(CONFIG_AUDITSYSCALL) += auditsc.o
ian@0 44 obj-$(CONFIG_KPROBES) += kprobes.o
ian@0 45 obj-$(CONFIG_SYSFS) += ksysfs.o
ian@0 46 obj-$(CONFIG_DETECT_SOFTLOCKUP) += softlockup.o
ian@0 47 obj-$(CONFIG_GENERIC_HARDIRQS) += irq/
ian@0 48 obj-$(CONFIG_SECCOMP) += seccomp.o
ian@0 49 obj-$(CONFIG_RCU_TORTURE_TEST) += rcutorture.o
ian@0 50 obj-$(CONFIG_RELAY) += relay.o
ian@0 51 obj-$(CONFIG_TASK_DELAY_ACCT) += delayacct.o
ian@0 52 obj-$(CONFIG_TASKSTATS) += taskstats.o
ian@0 53
ian@0 54 ifneq ($(CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER),y)
ian@0 55 # According to Alan Modra <alan@linuxcare.com.au>, the -fno-omit-frame-pointer is
ian@0 56 # needed for x86 only. Why this used to be enabled for all architectures is beyond
ian@0 57 # me. I suspect most platforms don't need this, but until we know that for sure
ian@0 58 # I turn this off for IA-64 only. Andreas Schwab says it's also needed on m68k
ian@0 59 # to get a correct value for the wait-channel (WCHAN in ps). --davidm
ian@0 60 CFLAGS_sched.o := $(PROFILING) -fno-omit-frame-pointer
ian@0 61 endif
ian@0 62
ian@0 63 $(obj)/configs.o: $(obj)/config_data.h
ian@0 64
ian@0 65 # config_data.h contains the same information as ikconfig.h but gzipped.
ian@0 66 # Info from config_data can be extracted from /proc/config*
ian@0 67 targets += config_data.gz
ian@0 68 $(obj)/config_data.gz: .config FORCE
ian@0 69 $(call if_changed,gzip)
ian@0 70
ian@0 71 quiet_cmd_ikconfiggz = IKCFG $@
ian@0 72 cmd_ikconfiggz = (echo "static const char kernel_config_data[] = MAGIC_START"; cat $< | scripts/bin2c; echo "MAGIC_END;") > $@
ian@0 73 targets += config_data.h
ian@0 74 $(obj)/config_data.h: $(obj)/config_data.gz FORCE
ian@0 75 $(call if_changed,ikconfiggz)